9.0.124.0 for IE7 is not detected

Flash9f.ocx is correctly installed in
C:\WINDOWS\system32\Macromed\Flash in my WinXP SP2 Home system, but
every Web site that I visit that requires Flash Player in order to
operate properly fails to detect that Flash Player is installed in
my system. I have no such problem with Firefox. I had no such
problem with 9.0.115.0. I'm running IE7 fully patched, and it's
functioning properly except for this Flash Player issue.
I've successfully installed 9.0.124.0 three times -- at least
the Adobe site told me three times that it was successfully
installed. I've submitted a bug report but have received no
response from Adobe.
Is anyone else experiencing this issue?

Because reinstalling 9.0.124.0 over itself wasn't working, I
decided to uninstall it and then do a fresh install. That resolved
the issue. Flash Player is now detected when I use IE7 to browse
Web sites that require Flash Player.
You have to use the Flash Player uninstall program to
uninstall it -- see "Safe versions security restrictions when
installing Flash Player (Internet Explorer on Windows)" at
http://www.adobe.com/go/kb402435.

Similar Messages

  • Installation procedure for WRT54GC does not detect router on Windows Vista.

    Today I bought a used WRT54GC, supposed to be in working condition.  I ran the installation procedure on my Vista laptop, following the detailed steps to the letter, and all was going fine, until the detection routine.  All the router's lights were blinking, and others solid, as per the instructions, but a few seconds later I got a message stating that ".. Setup was not able to find a Compact Linksys Wireless router on the network....etc".
    I immediately went to reset the unit, inserting a pin and waiting until the power light blinked several times (about 30 seconds).  This did not help.  I also reset the DSL modem, just in case, to no avail.
    I have contacted the vendor, and he users that the unit was fine. 
    The Linksys support page has several user's forums references to how to 'connect' using Windows Vista, but all assume the unit has already been installed and working, which I found frustrating, since I cannot install it!
    Any help will be greatly appreciated.
    Regards,
    gherna1

    The trick is not to use the installation disk, but connect the PC/laptop directly to the router (wired), let it assign the dynamic IP address (default action), and then use the router's interface to set it up.  Its address is 192.168.1.1 (it may be different for other models or brands).
    I was able to set it up this way and now I'm enjoying it.  Thanks to all who offered their advice.
    Regards,
    gherna1.

  • Touchpad went crazy for no reason : not detecting multitouch

    I have a Synaptics touchpad which I could do two finger scrolling just a day ago. Today, when I try using it with two fingers, the pointer just "flips out", changing its position million times a second.
    synclient used to show higher "widths" when I used multitouch (so I could scroll with pressure&width emulation), now it won't do that at all (it recognizes the width when I acutally use my whole finger, though)
    here's xorg.0.log :
    (II) Synaptics touchpad driver version 1.2.1
    (--) Mouse0 auto-dev sets device to /dev/input/event8
    (**) Option "Device" "/dev/input/event8"
    (II) Mouse0: x-axis range 1472 - 5472
    (II) Mouse0: y-axis range 1408 - 4448
    (II) Mouse0: pressure range 0 - 255
    (II) Mouse0: finger width range 0 - 0
    (II) Mouse0: buttons: left right
    (**) Option "SHMConfig" "true"
    (**) Option "FingerLow" "25"
    (**) Option "FingerHigh" "30"
    (**) Option "MaxTapTime" "130"
    (**) Option "EmulateTwoFingerMinZ" "70"
    (**) Option "EmulateTwoFingerMinW" "9"
    (**) Option "VertScrollDelta" "100"
    (**) Option "HorizScrollDelta" "100"
    (**) Option "CornerCoasting" "true"
    (**) Option "VertTwoFingerScroll" "true"
    (**) Option "HorizTwoFingerScroll" "true"
    (**) Option "TapButton1" "1"
    (**) Option "TapButton2" "2"
    (**) Option "TapButton3" "3"
    (**) Option "MinSpeed" "0.45"
    (**) Option "MaxSpeed" "0.90"
    (**) Option "AccelFactor" "0.0020"
    (**) Option "CoastingSpeed" "0.30"
    (--) Mouse0: touchpad found
    (**) Option "AlwaysCore" "true"
    (**) Option "CorePointer"
    (**) Mouse0: always reports core events
    (II) XINPUT: Adding extended input device "Mouse0" (type: TOUCHPAD)
    (**) Mouse0: (accel) keeping acceleration scheme 1
    (**) Mouse0: (accel) acceleration profile 0
    (--) Mouse0: touchpad found
    (II) config/hal: Adding input device Macintosh mouse button emulation
    (II) LoadModule: "evdev"
    (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
    (II) Module evdev: vendor="X.Org Foundation"
    compiled for 1.7.3, module version = 2.3.2
    Module class: X.Org XInput Driver
    ABI class: X.Org XInput driver, version 7.0
    (**) Macintosh mouse button emulation: always reports core events
    (**) Macintosh mouse button emulation: Device: "/dev/input/event0"
    (II) Macintosh mouse button emulation: Found 3 mouse buttons
    (II) Macintosh mouse button emulation: Found relative axes
    (II) Macintosh mouse button emulation: Found x and y relative axes
    (II) Macintosh mouse button emulation: Configuring as mouse
    (**) Macintosh mouse button emulation: YAxisMapping: buttons 4 and 5
    (**) Macintosh mouse button emulation: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
    (II) XINPUT: Adding extended input device "Macintosh mouse button emulation" (type: MOUSE)
    (**) Macintosh mouse button emulation: (accel) keeping acceleration scheme 1
    (**) Macintosh mouse button emulation: (accel) acceleration profile 0
    (II) Macintosh mouse button emulation: initialized for relative axes.
    (II) config/hal: Adding input device SynPS/2 Synaptics TouchPad
    (II) Synaptics touchpad driver version 1.2.1
    (**) Option "Device" "/dev/input/event8"
    (**) Option "TapButton1" "1"
    (**) Option "TapButton2" "2"
    (**) Option "TapButton3" "3"
    (--) SynPS/2 Synaptics TouchPad: no supported touchpad found
    (EE) SynPS/2 Synaptics TouchPad Unable to query/initialize Synaptics hardware.
    (EE) PreInit failed for input device "SynPS/2 Synaptics TouchPad"
    (II) UnloadModule: "synaptics"
    (EE) config/hal: NewInputDeviceRequest failed (8)
    and xorg.conf :
    Section "InputDevice"
    Identifier "Mouse0"
    Driver "synaptics"
    Option "AlwaysCore" "true" # send events to CorePointer
    Option "Device" "/dev/input/mice"
    #Option "Device" "/dev/psaux"
    Option "Protocol" "auto-dev"
    Option "SHMConfig" "true" # configurable at runtime? security risk
    # Option "LeftEdge" "1300" # x coord left
    # Option "RightEdge" "5500" # x coord right
    # Option "TopEdge" "770" # y coord top
    # Option "BottomEdge" "5300" # y coord bottom
    Option "FingerLow" "25" # pressure below this level triggers release
    Option "FingerHigh" "30" # pressure above this level triggers touch
    Option "MaxTapTime" "130" # max time in ms for detecting tap
    # Option "VertEdgeScroll" "true" # enable vertical scroll zone
    # Option "HorizEdgeScroll" "true" # enable horizontal scroll zone
    Option "CornerCoasting" "true" # enable continuous scroll with finger in corner
    Option "CoastingSpeed" "0.30" # corner coasting speed
    Option "VertScrollDelta" "100" # edge-to-edge scroll distance of the vertical scroll
    Option "HorizScrollDelta" "100" # edge-to-edge scroll distance of the horizontal scroll
    Option "MinSpeed" "0.45" # speed factor for low pointer movement
    Option "MaxSpeed" "0.90" # maximum speed factor for fast pointer movement
    Option "AccelFactor" "0.0020" # acceleration factor for normal pointer movements
    Option "VertTwoFingerScroll" "true" # vertical scroll anywhere with two fingers
    Option "HorizTwoFingerScroll" "true" # horizontal scroll anywhere with two fingers
    Option "EmulateTwoFingerMinW" "9" # this may vary between different machines
    Option "EmulateTwoFingerMinZ" "70" # this may vary between different machines
    Option "TapButton1" "1"
    Option "TapButton2" "2"
    Option "TapButton3" "3"
    EndSection
    I bought a new mouse and thought it was the reason, but I was already switching between touchpad and another mouse on the fly without any problem.
    The second possiblity is that I was trying to dim my backlight using some driver and I might have broken my touchpad as a result, but basic gestures (edge scroll,etc) work without any problem and also, I can use it flawlessly on windows.
    Any suggestions ?
    Last edited by felace (2010-04-16 14:34:10)

    I would like to say I have had this problem for a year now. It was working fine yesterday, and now when I booted into windows and back to archlinux it started going crazy on two fingers. Anyone have a solution? I desperately want this resolved.
    When I use two fingers it goes crazy, when I put my finger down so it covers a larger surface area it works (but that's not the way I want it).
    Edit: Okay, after a lot of googling synonyms, I got https://bbs.archlinux.org/viewtopic.php?id=77005. This solved my problems and this thread is solved.
    Last edited by caelestis (2011-01-22 20:07:54)

  • Camera for macbook pro not detecting camera since upgrade to mountain lion

    I recently upgraded from Snow leopard to Mountain Lion and I was trying to make a video call in skype. The camera worked for a minute or so then stopped working. Since then my camera hasn't been detected by my Macbook pro. Can anyone help me?

    I recently upgraded from Snow leopard to Mountain Lion and I was trying to make a video call in skype. The camera worked for a minute or so then stopped working. Since then my camera hasn't been detected by my Macbook pro. Can anyone help me?

  • Pages and Keynotes for iOS can not detect documents on my iPad 2

    ...but all documents can be seen on my iPhone 4s and on iCloud.
    Both iDevices updated to iOS 7.0.3., both apps updated with latest patch. I have tried to reset the iPad 2 (64 gb, WiFi+3G), with no positive effect. I saw this error yesterday evening for the first time. Everything was working Tuesday evening. I am able to access and work with the documents in iCloud on my PC. That work gets synced like it's supposed to.
    Any suggestions?

    That was fast - and it worked!
    Now I just have to figure out, how all those settings got turned off
    Thanks again for the help! Much appreciated

  • Battery is not detected in Equium U400-124

    Hi Guys,
    I bought a U400-124 yesterday and replaced it today for the same model and i still have the same problem.
    The notebook works fine when its conected to AC power but as soon as i unplug it the notebook dies ? Its not the charger thats the problem, i have changed that also. On the icon that tells you if the battery is charging or not it says "Battery is not detected"
    Does anyone have an idea why this happens ? All help would be hugely appreciated.

    Hey man
    I bought a Toshiba Equium U400 too. And i faced the same problem.
    So I took it to the ASP (Authorized Service Provider) and they said it was not the laptops problem it was the problem of the battery.
    So as I had a warranty I changed my battery and its running great..
    Try my idea and your going to be happy..
    So go to a Toshiba reseller or buy your battery online.
    So you did a wrong thing changing you laptop should have changed your battery... happy to help and tell me if u have any other problem.
    Bye

  • System Update 5 not detecting drivers for M92P (2988-A6U)

    I've installed our corporate image (Windows 7 SP1 - 64bit) which has an older network driver installed. 11.12.36.0
    The latest driver from Lenovo's web site is 11.15.16.0 which installs without a problem.
    So i re-imaged again with the older driver 11.12.36.0 and figured that the easiest way to update the driver(s) would be to use System Update 5. 
    To my surprise when i ran system update it returns the following:
    "No packages applicable to your system were found"
    No i know i could just fix the image and install the driver during the image process but I want to use System Update.
    Does anybody have a clue as to why System Update is not detecting the needed drivers?
    Has anybody had any success with running System Update 5 on a Windows 7 sp1 64-bit machines?
    Thanks-

    Unfortunately right now it appears that the 11.15.16.0 version of that driver does not have TVSU support yet.  Once the content team completes the process of creating and testing the package through TVSU, it will be published for customers.  I'll try to find out where this one falls in the queue. Sorry for the inconvenience.

  • HT4437 hi even when i connect my macbook and apple tv to the same wifi network i cant put on the air play mirroring option.my airplay mirroring option does not detect any device.what can i do for this?

    hi even when i connect my macbook and apple tv to the same wifi network i cant put on the air play mirroring option.my airplay mirroring option does not detect any device.what can i do for this?

    See
    http://support.apple.com/kb/TS4215

  • My wifi will not detect networks and will not search for other networks when I search for them. Do I need a new iPhone or can I fix it myself?

    My wifi is on and when it tries to find a wifi connection, the gray little circle just keeps spinning and will not detect our home wifi. I have tried to search for it and connect to it manually, but it will not search for the network name. I'm hoping I don't need a new phone so please help.

    The following may have something that will help: http://support.apple.com/kb/TS1398

  • *SOLVED* Device not detected/ No driver installed for X-FI Fatal

    OK!!!! the only reason I signed up here was to post that I have (for me) solved my problem.
    Before I get into details this occurred on a fresh system with latest drivers for hardware used.
    The problem was installing my X-Fi card on my 680i m/b (striker extreme).. when I would install the driver it would simply crash the computer and when it started up the hardware was not detected to used the software and the device manager said no driver installed.. I tried everything.. I installed the driver in safe mode (yay it worked without crashing) then I booted for windows only to have it blue screen for a second and restart... repeating the cycle.. so i reinstalled windows again... I tried installing the driver different ways in windows.. nothing worked... I gave up...
    BUT!!!
    today while i was at work I decided I would try one last thing.
    this is what got it going. I have SLI 8800ultras that covered the PCI slot on the bottom of my board and I though I would try the card in this slot to see if it worked there... so I disabled SLI took out my bottom card put in the sound card in the bottom slot, installed the driver... It installed 00% no crash... even better it worked after the restart!!!... so then I had to test if it worked in the top slot so I powered down, moved it up to my top PCI slot and windows auto set the driver for it (as it was already installed) It worked in the top slot now... Finally I put in the second 8800 to make sure it worked with this slot in use... It still worked fine with SLI enabled. because I was unhappy with the mess I made installing drivers all the time as I did with the many crashes I decided to do a fresh install of windows making this card work from the start so here is what you need to do if you have a 680i board with SLI. this is exactly what i did with my fresh install.
    install only one GPU card..
    Put the X-FI in a different slot that isn't giving you problems
    Install windows
    Install service pack 2
    install your chipset drivers
    install sound card drivers
    power down, change sound card to permanent slot
    test - power down
    put in the second GPU card
    install GPU drivers
    Good luck you all having this problem.. I hope my solution helps you.
    Bryan

    I think I?got a similar?problem earlier today when I was messing around with?onboard audio?that I later removed and after unplugging a?USB headset.
    Have you checked the device manager, is there any higlighted hardware that has a exclamation mark next to it.
    I fixed the issue by simply uninstalling the WDM device with the exclamation mark and restarted.

  • External display for T520 not detected

    Hi!
    I have ThinkPad T520 and Samsung 17'' display with DVA output. I bought DVI-VGA adapter and connected the display to laptop's VGA input. The external display is not detected - it is not present in Windows 7 display properties and it shows "No connection, check signal cable" on it's screen. I don't think that there is something wrong with adapter, because it's new. How can I setup it correctly?
    Thanks!

    Hi, koles
    Thank you for the information. In the past, updating BIOS was something that was rarely done, as it could lock up and not work, which would render the computer useless if it failed. Today, however, it is not like it once was. As with updates, there is still some risk involved, but there is now a utility that will update the BIOS for you. If you'd like, you can update all the other drivers first and then do the BIOS as a last resort if you would rather not try it unless you need to.
    Hope it helps. Keep me posted!
    Best,
    Adam
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution!" This will help the rest of the community with similar issues identify the verified solution and benefit from it.

  • A solution for idevice not detected/synced with itunes (11.3 ios 7.1.2 also here)

    hello !
    -the problem i had :
    all perfect, but since last itunes my iphone 5s was not detected anymore by itunes 11.3 or 2 (who cares... but me)
    updated my ios to 7.1.2 then tryied again to sync WIFI-USB to iTunes... => fail !
    (i thinked about wiaitng for a next itunes and/or ios from apple to fix that... but i wanted to fix fastler.)
    (Probelms some have : they reboot their iphone with "connect to itunes" coz their iphone want to be  "RESTOREd" on tiunes when plugged... => THERe NO MIRACLES for that... wait ios update n/or itunes update so..)
    ALWAYS SAVE YOUR idevice USING ICLOUD !!!! IT SAVES ... ALL !! (includings apps data, but the apps themselves ! USE IT ! i done this...)
    -a Fix i have done that worked perfect for me :
    my iphone so was working perfect after ios 7.1.2 update but could not sync...
    so i activated icloud sync on it .... used the "sync to icloud - SAVe NOW" ....
    and...
    (crossing fingers..)
    i restored my idevice !
    (/!\ SINCE my iPhone 3G 16 Mb i never had any problems... or just a bit but always tried to solve by using google or YAHOO..)
    so i restored ALL my iphone LIKE AS LAST STATE ! (i had just to DL all apps, but it's automatik....)
    games saves, apps saves ? (probly too... will test...), all photos docs etc.... where on icloud it was just 1,2 Gb data (not including apps again.)
    -iTunes was not detecting my iDevice (iphone 5s) :
    for this i searched (hadly) on this forum... and found this solution that worked for me :
    (Itunes can't recognize my IPhone ) <- click topik link
    if i remember well ... (i am on PC win 8.1 x64 bits) ...
    you must desinstalle :
    "APPLE SOFTWARE UPDATE", "iTUNES" and "APPLE MOBILE DEVICE SUPPORT" and (.... 30 sec plz...) .. and " APPPLE application support" also...
    (not sure but check this link just up here ^ ....)
    voilà...
    ->
    THINK ALSO, YOUR iDEVICE USB CABLE MUST BE "CERTIFIED FOR APPLE" .... i bought a chineze cable for 5 € did not worked...
    i bought a "BELKIN" on Amazon it works flawless... (coz it's certified apple, even it's not an apple... but solid one)
    ->
    don't forget to reboot your system before relaunching the itunes if u need reboot...
    i hope i helped somes here...
    iDevice are REALLY NICE i love them but sometyimes they caprices.... (sciences is unperfect)...
    -> dont let it down (this topik) this can serves... well !
    peace...

    ALWAYS SAVE YOUR idevice USING ICLOUD !!!! IT SAVES ... ALL !! (includings apps data, but the apps themselves ! USE IT ! i done this...)

  • How can I import photo to computer if my photo were save in event instead of saved photo for ipad1?  Why Photo in event are not detected ?

    How can I import photo to computer if my photo were save in event instead of saved photo for ipad? Photo in event are not detected.

    Importing Personal Photos and videos from your iOS device to your computer.
    http://support.apple.com/kb/HT4083
     Cheers, Tom

  • HT1212 I have forgotten my passcode for ipad and itunes is not "detecting a device in recovery mode."

    I have forgotten my passcode for ipad and itunes is asking passcode to be entered - even after following directions for computers not synced... multiple times, but iTunes is not "detecting a device in recovery mode."  What do I do now?

    DFU Restore
    This will very likley result in loss of data.
    Plug the iPhone into the computer.
    Ensure that it is running the latest version of iTunes and that it has access to the internet.
    Press and hold both the home and sleep/wake buttons for exactly eight seconds.
    Release only the sleep/wake button but continue to hold the home button for another five seconds.
    Let go of the home button, then look at the computer screen for an instructional popup.
    The popup should say "iTunes has detected a device in recovery mode. . .(etc)"  Click accept to all boxes and let iTunes download and install all of the latest device Firmware and Software.
    If no popup appears, repeat the above DFU instructions.  If you've never done a DFU, it may take about three attempts to get the timing right.

  • [svn:bz-trunk] 21394: bug fix for watson 2887837 Not getting duplicate session detected error when same flex client id is used from two different HTTP sessions in CRX .

    Revision: 21394
    Revision: 21394
    Author:   [email protected]
    Date:     2011-06-16 12:34:13 -0700 (Thu, 16 Jun 2011)
    Log Message:
    bug fix for watson 2887837 Not getting duplicate session detected error when same flex client id is used from two different HTTP sessions in CRX.
    get the sessions id before we invalidate the duplicate session.
    Checkintests pass
    Modified Paths:
        blazeds/trunk/modules/core/src/flex/messaging/endpoints/BaseHTTPEndpoint.java

    For our profect I think this issue was caused as follows:
    Believing that remoting was full asynchronous we fired a 2 or 3 remote calls to the server at the same time ( within the same function ) - usually when the users goes to a new section of the app.
    This seemed to trigger the duplicate http session error since according to http://blogs.adobe.com/lin/2011/05/duplication-session-error.html  two remote calls arriving before a session is created will cause 2 sessions to be created.
    Our current solution ( too early to say it works ) is to daisy chain the multiple calls together .
    Also there seemed to be an issue where mobile apps that never quit ( thanks Apple! )  caused the error when activated after a few hours.
    I guess the session expires on the server and the error above occurs on activation.
    So the mobile apps now ping the server with a remote call when activated after sleeping for more than one hour.
    All duplicate http errors are silently caught and reported.
    Fingers crossed we won't get any more!

Maybe you are looking for