[915 Series] 915P combo and P4 530j model cpu

I get 4 red DLEDs at boot attempt. I have bios 1.3. Do I need an older cpu to boot to flash the bios to 1.7?
Using a enermax 500 watt noisetaker, 24 pin psu. 2 sticks of Centom 512mb memory, tried just 1 stick... same I have removed all parts but the video and ram. no vid signal, 4 red lights...
Matt

Did you make sure you plugged in the 4 pin power into the motherboard? If so try removing the CPU and reseating it.
Good Luck
Jeremy

Similar Messages

[915 Series] 915P Combo Problems.. Can anyone help Please?

Hello everyone!
I'm pleasured to be in contact with you, I'm from Portugal, so any errors in my english, please excuse me
I've bought an MSI Motherbnoard 915P Combo and there is some questions that I need your help.
My system is:
MSI 915P Combo 8latest 1.6 Bios version)
Pentium 4 LGA775 3.0 GHZ
Zalman 7700 Al-CU
1GB Kingston PC3200 2x512 (Dual Channel, 3-3-3-7)
XFX Geforce Nx 6200 PCI-Express (with direct power alimentation from the PSU.. is this normal?)
Enermax 350w Noisetaker ATX 2.01 (with all stability since I've bought to my P4 Socket 478)
160GB Seagate Barracuda SATA NCQw/8MB Cache
Pioneer DVR-108 16x DVD+RW
Thermaltake Shark Aluminium Case
Integrated 5.1 Sound Solution (Azalia)
Ok... the problem is... my computer doesn't shut Off! I've installed the Windows Xp and SP2 from new, bu when I'm choosing the option "Shut Down" win windows, the pc shutt down only 3 seconds!!!
By the on/off button is everything ok...
Can anyone help me?
Thank's in advance.

Quote from: NovJoe on 21-March-05, 20:30:51
Check your power button connector to the mobo and see if it was fixed properly or you can try turning the connector 180 degrees around and fix it in and see if the same problem replicates.
Next you can also try to clear CMOS.
Check in your Power Management Options in Windows and check if there's any funny settings.
Thank you very much NovJoe for your kind attention and help.
Since I arrive home I'll try that.
i've tried the connector of the power in the board of the 2 possible way with no result.
How can I clear the CMOS? nly with Jumpers isn't?
And what do you mean to say with funny settings in windos? Can you be more specific please?
Regards

[915 Series] 915P Combo installation trouble

I am attempting to install a 915P Combo board with a Pentium 4 530J 3.0/800/1G processor. At the moment I have only 1 DIMM, the processor, the power supply and the case power switch and speaker connected to the board. The memory, power supply and case are known to function properly. (I experienced the same symptoms with my system fully connected, and the system did not post.) Here is the situation:
After pressing the power button I hear one long beep and six short beeps. This combination is not listed in the Basic Troubleshooting Guide. When I had the D-LED installed the system hung with the bottom left and top right lights green and the other two orange. This combination is indicated as the processor read indication.
Any thoughts? Thanks.
EDIT: the one long beep and six short beeps might be eight short beeps; it's hard to tell. Eight short beeps is listed as indicated a display error, so I tried reinstalling my brand-new PCIx16 card. No luck.

AMI BIOS (American Megatrends Inc) don't have long beeps, just short beeps.
in ur case we have
6 Beeps 8042 - A20 Failure
8beeps Display memory read/write failure
So you must install your VGA card in another system.
AWARD BIOS have long beeps..
1 long 9 short, BIOS ROM error...
Just make sure your PSU is ok, Clear the BIOS, and send this mainboard for a check

915p Combo and Leadtek Winfast PVR2000 - No Sound on live playback

Has anyone attempted to install a (PCI card) PVR2000 onto a 915p Combo board and utilise the onboard sound rather than a dedicated Sound Card? I've attached the PVR card to the motherboard via the CD-In connector (JAUD1 or something), but only get sound when playing back captured TV or Radio. This suggests that the card is working, but the motherboard can't hear it through the connector. I've tried replacing the cable with one that definitely works and updated the Leadtek and Onboard Sound drivers, but to no avail.
Can anyone help?
Thanks!

Download the latest drivers for the C-Media soundchip, PVR2000 and the latest version of WinFast PVR. After that go to the Configuration Screen in Winfast and select CD-Player for Audio-in &Audio-out. In Cmedia Xear->Mixer select CD-Player in Rec and click the button that looks likea speaker (a hammer in earlier versions and select Monitoring).

"915P Combo and PCI-Express problem"

Hello friends, I have a pc with the following configuration: mobo 915P Combo with a processor pentium 4 530 3.0 ghz, memory kingston 1GB Kit DDR 400 dual channel, psu 500w ATX with connector 20-pin, video card XFX Geforce 6600 256 MB PCI-EXPRESS, sound card audigy 2 zs, hard disk 120 GB seagate 7200 rpm SATA. And I have a problem with the port PCI-Express and my video card, if I install the video card the computer it doesn't start up well, that is to say, it start up and to the 3 seg this shut down automatically and 5 seg later this tries to start up but without success , after several intents this can start up perfect and everything works well . And if I don't install the video card pci-express and I intall my old video card port pci 16 mb Banshee the pc starts up perfect and doesn't have problems. what is the real problem? 1) the video card pci-express, 2) the port pci-express of the mobo, 3)that I have a psu with connector 20-pin? Thanks

dear moderator,
i got same problem as Calvido. My system specification MSI 915G Combo with the lastest bios v1.8 with a processor pentium 4 530 3.0 ghz, memory kingston 1GB DDR 533 dual channel, psu 350w True power, video card Leadtek Geforce 6600 256 MB PCI-EXPRESS, hard disk 120 GB maxtor 7200 rpm SATA. And I have a problem with the PCI-Express, if i use the intergrated graphic intel 900 it dun give me any problem n i used for more than 6mth.
It happen when i try to upgrade my intergrated graphic card to PCI-E. 1st i try with the Inno3D geforce 6600 256mb PCI-E n when my com start until windows it become blank screen for awhile the screen appear again for no more than 1 min became blank again. 2nd try i use Leadtek Geforce 6600 256MB PCI-E it seem alright but when i click on icon it start to delay ...until hang. 1st i thought my OS problem so i format my system, but problem still the same so i repeat format until 7 or 8 times. Problem not solve.
I try to send email to MSI but no reply
Pls help me to solve the problem
best regard

[915 Series] 915P After switch off - keyboard LED and mouse are ON

Hi,
when I switch off from WinXP, keyboard LED and mouse stay ON. Why? Any suggestions, how can i fix this?
Thanks (915P Platinum, latest BIOS, WinXP Pro)

ha... looks like MSI didn't do proper vaidation on either hardware or BIOS.
MAYBE the next BIOS will fix this, or MAYBE it's true hardware "feature". If that's the case, well, just live with it.

[915 Series] 915G-Combo with OCZ-DDR2-533/4200 no post - help!

I was hoping one of you wonderful experts on this board might be able to help. I just bought a pair of OCZ DDR2-RAM and am having trouble getting the system to recognize it. Here are the specs:
RAM specs:
- 533MHz DDR2, unbuffered CL 3-3-3-8
- 1GB (2X512) dual channel optimized gold kit
- 1.8V 240pin DIMM
- 2.2V EVP - OCZ's unique Extended Voltage Protection feature allows PC2-4200 modules to handle voltages up to 2.2V ±5%
- OCZ part number:-OCZ25331024ELDCGE-K
System specs:
* CPU model and rated speed:-Intel Socket775 2.8GHzE
* Not Overclocked
* Motherboard and revision:-MSI 915G-combo
* Motherboard Bios rev:-1.7 (latest)
* Video card:-ATI X800XL
* Power supply:-450W
* Operating System:-XP Pro SP2
My current Crucial DDR-400 PC3200 CT6464Z40B 2x512MB RAM runs without problems installed. When I switched out the Crucial RAM and installed the OCZ DDR2-533 PC4200 RAM in the appropriate DDR2 slots (1 and 3), no go. The system won't even post and I can't get into the BIOS. I tried using even just one of the 512MB sticks, alternated sticks, and even tried just one stick in DDR2 in slot3 instead of slot1 - no go. My boot drives don't get accessed either as I had even placed a Memtest bootdisk in the floppy hoping it might be able to access that.
I've been working over the last 24hrs with the very helpful OCZ folks but we havn't been able to get anywhere. I realize that OCZ isn't technically on the 'tested and verified' DDR2-list for the 915G-combo board, but OCZ is a good name brand (up there with Crucial) and I went for the higher-end Gold-series (CAS3) so I figured it wouldn't be a problem.
I've tried clearing the CMOS (no effect except to wipe out my bios settings). I have a D-Bracket2 installed and it hangs when the upper right light is green with the rest red (according to the D-bracket guide, that means 'Memory Detection Test - will hang if the memory module is damaged or not installed properly'. I can't imagine the RAM is bad - I have 2 matching ones to test (neither seem to work when installed by itself), and just got it brand new from Monarchcomputers yesterday evening in their retail box unopened.
Per OCZ's advice, I was unable to manually set a CAS of 4 with my Crucial DDR installed (I could only manually set it to a max of 3), so I also test-tried a manual set of the BIOS memory timing to 3-4-4-10 while the Crucial DDR RAM was installed and then retried the system with only the new DDR2 installed in their appropriate slots (Crucial DDR of course removed). Still no luck - the system won't get to bios and hangs at the Memory Test per D-Bracket2. It won't even get to a point where it tries to access/boot from floppy so that I can't run MemoryTest from disk.
Would anyone else out there recommend trying something else, short of going out and shelling out $140 for an ABit AA8-925X mboard that OCZ actually lists as compatible with their RAM? My MSI 915G-Combo board has been flawless for me up to now and I'd hate to part with it just because it won't work with good OCZ DDR2 ram. One thing I havn't tried is attempting to use an older BIOS version - I had flashed to the latest v1.7 bios prior to installing the DDR2 ram, so I've never actually tried any of the older versions. Does anyone think this would be worth a shot?
Cheers
- James

Thanks... I tried that.... still no go...
I just got an email from OCZ techsupport (they had requested that I email them directly).
"we have identified a problem with the PC4200 Gold DDR2 dimms, we need to get you a pair with reprogrammed SPD info on them. So we need to swap your kit out"
They were very apologetic about it, and from what I can tell I don't think this happens a lot with OCZ ram...
So that hopefully will be the solution to my problem.. I'm processing an RMA with them right now.. will let you know how it goes.. it's a 'relief' to find out that it most likely isn't my MSI-915G board's fault after all...
Kudos to OCZ at least for getting back to me so quickly, even though it does suck to have my memory delayed again.. I'll post again when I get the replacement RAM and let you all know how it goes... at least they've identified a problem and are willing to take care of it rather than leaving me hanging...

[915 Series] Ethernet Controller and SM Bus Controller Drivers

I have a 915P Neo2 Platinum Motherboard.
I recently built a computer. When I put the driver CD in my computer freezes on loading. I have trieed finding the source of that problem. Now I am trying to Download the drivers. I have downloaded most but the two Question mark thingos it says on my device manager list are "Ethernet Controller" and "SM Bus controller". I have searched on the driver download list. I can find the right ethernet controller but when I download the zipped folder and unzip it, it just has a few random files that I cant open. No setup files. How do i use these files?

Hi Adams.. first we need your sys specsQuote
-CPU speed, FSB speed and OC speed which you always run if you OC, also include whether HT is enabled or not.
-RAM, the timing and the OC timing which you always run,
-exact motherboard model,
-display card, if u OC include the info as well
-PSU, power supply unit, brand and model, even better to include the exact wattage of all +3.3V, +5V and 12V rails
-HDDs, CDROMs and which ports you plug them in
-other PCI cards and which slots you plug them in
-other peripherals like USB, 1394 devices which you plug them in and create the issue
-BIOS settings which you changed from the default values, such as enable/disable some built-in devices, ACPI, etc
-OS, with service pack

[915 Series] sata II and DDR2 higher than pc4200...2 questions.

Can i put sata2 on my MSI 915 G COMBO ?
What's the differenc betwin pc4200 (533) and pc4300 (533)? Looks like the 4300 is a ddr 538!???
If i try a memory higher than PC4200(533) on the same MB(915g) it will reconize it as a 533 or 400?
cheers

Quote
Can i put sata2 on my MSI 915 G COMBO ?
SATA2 is supposed to be backwards compatible.
Quote
What's the differenc betwin pc4200 (533) and pc4300 (533)
A typo?
Quote
If i try a memory higher than PC4200(533) on the same MB(915g) it will reconize it as a 533 or 400?
It might run it at 533, but as the natural FSB for that board is 800, the probable (and desired) result is it will run at 400, leaving lot's of room for overclocking at a 1:1 ratio.

[915 Series] 915P Combo2 v3.2 sound drivers for Windows 7

Hey i'm having a problem trying to find a driver for my sound card there are no windows 7 updates for the 915p combo2 v3.2 and i was wondering if i could get some help getting one.

Holy thread from the dead Batman!
I'll split off your post from the 5 year dead thread.

[915 Series] SATA, IDE and the 915G.

Hello all,
I have an enquiry and did a peruse through the manual to no avail, so I am turning my enquiry over to you all.
Is the 915G Combo motherboard capable of running two Hard Disks via IDE connections AND two or more SATA Hard Disks at the same time?
Regards,
Thor

Quote from: MSI
On-Board IDE / SATA
• Dual Ultra DMA 66/100 IDE controllers integrated in ICH6.
- Supports PIO, Bus Master operation modes.
- Can connect up to two Ultra ATA drives.
• Serial ATA/150 controller integrated in ICH6.
- Up to 150MB/sec transfer speeds.
- Can connect up to four Serial ATA devices.
IDE RAID
• VIA6410 IDE RAID Controller
- Two Ultra DMA 66/100/133 IDE Controllers.
- Supports RAID 0, 1 and 0+1.
- Connect up to 4 Ultra ATA 133 devices.
According to the MSI product page, you should be able to connect up to 6 PATA (IDE) and 4 SATA together. I see no reason why you should not be able to use all of them at once.
Good Luck
Jeremy

[915 Series] 915p Neo2 HDD/Optical Drive Setup

I have a system as stated in signature with the two hard drives on a single cable and both set for Cable Select. I also have two optical drives on a single cable both set for Cable Select. When HDD cable is in IDE1 (blue connector) and CD-ROM cable is in IDE2, WinXP will run and recognize all four drives. However, I cannot boot from a CD. If I reverse the cables the CD will load, but will tell me I have no HDD.
Initially, to load XP I had one CD-ROM in cable position master and an HDD in cable position slave, other wise I got a message "no system found" or "Win could not find a HDD".
I have reviewed several posts and have not been able to find a solution. Everything works fine when in normal operation (booting from HDD) but when booting from proprietary softwhere on CD which can't be loaded on an HDD & must be loaded from the CD, I have to open the machine and swap cables and both I and my cable connectors are getting tired of this approach.
The BIOS tells me that I am using VIA VT6410 Raid BIOS Ver. 4.50 and with the HDD cable connected to IDE2 it lists the two drives as None Raid Primary Master & Slave.

Best to have your boot HDD as master on primary IDE with second HDD as slave on Primary IDE. Put burner as master on secondary IDE with cdr as slave to it.
Cable select is known to give problems in a lot of instances. Best to use master/slave jumper settings.

BIOS Problem with 915P Combo

Hi there...
I have one MB 915P Combo and i have problems in BIOS configuration.
I go to: Advanced BIOS Features / BOOT SEQUENCE
And have one option Boot from other Device, it have No.
I change to Yes, and reboot and now it is possible to use pen disks.
The problem:
If i install a program and at the end of installation (for example update IDE/Raid utility) it is necessary to reboot windows , i restart the windows and when go to windows, now is not possible to use pen disks...
To solve the problem temporaly:
It is necessary to go to the BIOS configuration and Change the Boot from other device to "No" and reboot... and Change again to "Yes" to work with Pen disk.
And sometimes appears a blue window in Windows with a Device Driver error.
How to solve the problem ?
I have the latest BIOS 1.6
Thanks.

What if you just normally reboot windows without any new installation? Does it happen the same way?

915P Combo POST problems

Hi All,
First i would like to say great site and wonderful info provided. my problem has to do with starting up the computer. When turned on the computer doesn't POST and I have to press the reset few times to get to POST. here is how it goes: When turned on "CPU fan makes throaty sound 'too much for just starting up'". then the mouse + keyboard light check, either lights up indicating a POST in progress or they don't during all of that the monitor is still not POSTING.
Out of 10 start ups 9 require pressing the reset button 5-10 times to get it to post. could anyone please give some feedback on this problem. Also if it is not too much does anybody know why a computer with a SATA master HD and a Third primary ATA133 HD won't let me add any more drive and will ask for RAID to be installed? having problems connecting my CDRW ROM with 2 HDs and a DVD drive installed i have to manually open the case and unplug the DVD drive and swap it with the CD writer if i want to burn something on CD. Thanks again for the help.
MSI 915P Combo AMI BIOS v 1.6
Intel P4 530J 3.0GHz 1MB L2
2 x 512MB 'Generic' PC4200 DDR2 533MHz Unbuffered
420W Generic PSU
RADEON X700 Pro 256MB GDDR3
1x 80GB S-ATA Maxtor DiamondMax 8MB Buffer
1x 60GB ATA133 Maxtor
2x LG Flatron L1950 LCD
LG GDR8163 DVD-ROM
SoundBlaster Audigy2 ZS
WinXP Pro SP2
DirectX 9.0c
MS Wireless Key+Mouse
ATI Catalyst Suite5.5

Dude i'm telling you I'm having the exact same problem.......
after hours of troubleshooting and reading these forums and whatnot I've found out I am not the only one having this problem.....these MSI boards are pieces of i'd return it if I were you
this is the response I got from MSI's technical support via email
Dear Customer,
Since have tried a known good power supply then try with board outside of case with minimal components if same have board replaced with reseller if just received if had been working and issue occurred the can rma through us Thanks
Technical Support Division
MSI Computer Corp.
with such good english you can tell that MSI really puts alot of effort into customer support........The guy on the phone was foreign and hard to understand also and he said the same thing....Send it back!
I'm not getting a replacement either i'm getting an exchange because it is ridiculously evident through the 15-20 posts both here and on the online help section that this model of board is indeed a pile of and has many similar problems with no real answers. We got wtfpwnd, cut your losses and send it back

915P Combo for SATA RAID

Okay, I just recently purchased a 915 P combo. I'm trying to setup a SATA raid and I don't have the option. The bios version is 1.2 and it's southbridge is a intel ICH6R. When I go into ATA/IDE configuration [Enhanced] I only see IDE and AHCI but no RAID. I have two 200gig WD hard drives. I don't know if this means anything either but the post screen says found primary master IDE drive and then says found secondary master ide drive. I'm not sure if it should say SATA or something else then IDE. Any help would be greatly appricated.

I purchased the 915P Combo from NewEgg.com which says:
"SATA/RAID: 4x SATA, 2x ATA(VT6410) 133 with RAID 0/1/0+1"
which led me to believe that it could do SATA RAID. My 915P box even says "SATA RAID - supports SATA and IDE interface RAID 0, 1 or 1.5". On the front of the box, like someone else mentioned, there is a big sticker that says "Intel ICH6/6R Test OK" which I can understand would not necessarily guarantee it had the 6R.
Looking closer at the sticker on the side of the mobo box it does say "P4-800, 915P, ICH6, ...." and not "ICH6R", but until reading this thread, I didn't even know what ICH6/ICH6R was, and wouldn't have helped me before purchase.
I think this is misleading and I'm pissed off- I purposely purchased two SATA 160gig drives when buying the parts for my new computer, soley to do RAID striping, and now I can't. I will be asking NewEgg for a refund and will likely not be buying another MSI product.
IF I were to purchase another MSI board, what SHOULD I get to have the SATA RAID features? (and will accept my P4-3GHz 800M LGA775 530, and DDR2)

[915 Series] 915P combo and P4 530j model cpu

Similar Messages

Maybe you are looking for