[915 Series] SATA, IDE and the 915G.

Hello all,
I have an enquiry and did a peruse through the manual to no avail, so I am turning my enquiry over to you all.
Is the 915G Combo motherboard capable of running two Hard Disks via IDE connections AND two or more SATA Hard Disks at the same time?
Regards,
Thor

Quote from: MSI
On-Board IDE / SATA
• Dual Ultra DMA 66/100 IDE controllers integrated in ICH6.
- Supports PIO, Bus Master operation modes.
- Can connect up to two Ultra ATA drives.
• Serial ATA/150 controller integrated in ICH6.
- Up to 150MB/sec transfer speeds.
- Can connect up to four Serial ATA devices.
IDE RAID
• VIA6410 IDE RAID Controller
- Two Ultra DMA 66/100/133 IDE Controllers.
- Supports RAID 0, 1 and 0+1.
- Connect up to 4 Ultra ATA 133 devices.
According to the MSI product page, you should be able to connect up to 6 PATA (IDE) and 4 SATA together. I see no reason why you should not be able to use all of them at once.
Good Luck
Jeremy

Similar Messages

[915 Series] sata II and DDR2 higher than pc4200...2 questions.

Can i put sata2 on my MSI 915 G COMBO ?
What's the differenc betwin pc4200 (533) and pc4300 (533)? Looks like the 4300 is a ddr 538!???
If i try a memory higher than PC4200(533) on the same MB(915g) it will reconize it as a 533 or 400?
cheers

Quote
Can i put sata2 on my MSI 915 G COMBO ?
SATA2 is supposed to be backwards compatible.
Quote
What's the differenc betwin pc4200 (533) and pc4300 (533)
A typo?
Quote
If i try a memory higher than PC4200(533) on the same MB(915g) it will reconize it as a 533 or 400?
It might run it at 533, but as the natural FSB for that board is 800, the probable (and desired) result is it will run at 400, leaving lot's of room for overclocking at a 1:1 ratio.

Can any body please give me an idea and the Import and Export process?

Can any body please give me an idea and the Import and Export process? Excise Duty and other duties and so on.
I will be highly obliged for the help.
Regards,
Subhasish

for importing material,every importer has to file bill of entry in customs.
first vendor send some documents like certificate of origine , bill of lading, packing list etc to importer.
on the basis of those documents,importer makes supporting documents like duty calculation sheet, GATE declaration form,CHA declaration form,insurance certificate.
CHA (custom house agent ) file the bill of entry on behalf of impoter in customs.
custom verify it.
after duty payment, CHA can clears the consignment from custom.
there are two typs of BOE.
1 Home consumption BOE
2 Warehousing BOE
in 1st type of BOE , payment of duty is done at the time of custom clearance
and in 2nd type of BOE, importer can put material in warehouse without payment of duty. at time of using those material from warehouse,importer has to file out bond warehouse BOE and pay the all duties.

Sata Drive and the KT6V Motherboard

Hi all, Wondering if anyone could help me. I just got a new PC and am setting it up as a server. Now I have a 40G hhd running the O.S. which is windows 98se ( I know its old and has problems but it should work fine) I also have a 120g WD SATA drive that i want to use as a storage drive. ( I have a set up on my other pc this way) but windows does not see the Sata drive and when i try the raid setup I see the Drive but i cant do anything with it. My mother board is a KT6V and all drivers and programs are loaded. I can use the Raid Tool and see the drive it says its working but again I cant do anything with it. Just wondering if this is the way this MotherBoard runs or if there is a setting im missing. Thanks for your time.

Hello,
Win98se,
How did you format the 120GB sata drive?
With the KT6 boards, if you have only one sata drive and enter the Sata ROM, you cannot choose any options, That is normal.
Must be using FAT32 for win98se.

[915 Series] Ethernet Controller and SM Bus Controller Drivers

I have a 915P Neo2 Platinum Motherboard.
I recently built a computer. When I put the driver CD in my computer freezes on loading. I have trieed finding the source of that problem. Now I am trying to Download the drivers. I have downloaded most but the two Question mark thingos it says on my device manager list are "Ethernet Controller" and "SM Bus controller". I have searched on the driver download list. I can find the right ethernet controller but when I download the zipped folder and unzip it, it just has a few random files that I cant open. No setup files. How do i use these files?

Hi Adams.. first we need your sys specsQuote
-CPU speed, FSB speed and OC speed which you always run if you OC, also include whether HT is enabled or not.
-RAM, the timing and the OC timing which you always run,
-exact motherboard model,
-display card, if u OC include the info as well
-PSU, power supply unit, brand and model, even better to include the exact wattage of all +3.3V, +5V and 12V rails
-HDDs, CDROMs and which ports you plug them in
-other PCI cards and which slots you plug them in
-other peripherals like USB, 1394 devices which you plug them in and create the issue
-BIOS settings which you changed from the default values, such as enable/disable some built-in devices, ACPI, etc
-OS, with service pack

I have downloaded a tv series into itunes and the third episode won't play. We have successfully watched the first two. What is the problem?

I am having trouble viewing the third episode of a tv series that I have downloaded on Itunes. Any suggestions?

It won't work, they are linked to your account and can only be played via iTunes on a computer, an iOS device or Apple TV. You might be able to get a cable to link your Mac to your TV so that you can play/mirror it through your TV e.g. if it's a Macbook with an HDMI socket and your TV also has an HDMI socket then you could try an HDMI to HDMI cable (Apple do them, and electrical stores should also have them) - I've used one to play iTunes TV programmes on my TV (though I don't think that I got sound through my TV, only my Mac).
Message was edited by: King_Penguin

Netbeans IDE and the Jar file

I can't find the jar file compiled by Netbeans anywhere. In the preferences it says the "dist" folder, but that returns nothing when I search my computer.
I'm using the Mac OS X release, if that helps at all.

I've just had a look at NetBeans (on a Windows machine). The jar file is not created until I choose "Build Main Project". At that point a helpful message appeared saying:To run this application from the command line without Ant, try:
java -jar "C:\Documents and Settings\pbrockway.WXPD6OFF\WhereAmI\dist\WhereAmI.jar"The jar file also appears in the "Files" tab (under dist). There doesn't seem to be any way of running the jar file from the NetBeans IDE - or at least, I couldn't find it: others might be more knowledgable about this.

I bought a tv series from 2009 and the last episode will not download

I bought the 7th season of the biggest loser on Itunes and can not get episode 719 to download. this is rather frustrating since I spent money to get the whole series. It just keeps saying that it wont download. ANysuggestions

How much space do you have free on the iPad?

[915 Series] CPU Voltage and clock multiplier

The manueal of 915G combo says(page 3-24):
Adjust CPU Voltage
The settings are used to adjust the CPU clock multiplier(ratio) and CPU core voltage....
I dont know how, and you?
Can anyone explain that to me, please.
cheers

If the value has a "v" or "X.XX", it'll be the value for setting the CPU voltage as Mutiplier settings only comes in full numeric value like 1, 2, 3, 4... 20 etc.
My guess of why it is being phrased as such is mainly to due the different settings to o/c a system may require a minor increase of the CPU Voltage to keep the whole system to run stablely.

I am trying to edit a home movie on iMovies but when I try to download the movie from a dvd a message comes up saying there are no importable files. The DVD is the last in a series of 5 and the others have downloaded without any difficulty.Help?

I am trying to edit a home movie on iMovies on a mac book air. The movie is on a dvd but when I try to import the movie onto iMovies I get a message saying there are no importable files. I've downloaded the macx converter software but I can't seem to download the movie into that either.

Chris , thanks for the prompt reply. The dvd was produced by a third party that I found on line . I had a number of old mini digital video cassettes from a Sony Handycam. I can play the DVD's on my laptop but I can't edit them on iMovies to delete a lot of the rubbish on them. I have five DVD's and three downloaded without any problem but the last two are according to iMovies non importable.

[915 Series] 915P combo and P4 530j model cpu

I get 4 red DLEDs at boot attempt. I have bios 1.3. Do I need an older cpu to boot to flash the bios to 1.7?
Using a enermax 500 watt noisetaker, 24 pin psu. 2 sticks of Centom 512mb memory, tried just 1 stick... same I have removed all parts but the video and ram. no vid signal, 4 red lights...
Matt

Did you make sure you plugged in the 4 pin power into the motherboard? If so try removing the CPU and reseating it.
Good Luck
Jeremy

SATA/IDE Problems

Brief system specs:
# CPU: Intel core2duo 6600 @ 2.4 GHz
# Motherboard: p965 Neo
# Memory: 2x 512
# Vidcard: evga 7900gt
# HDD: 1x WD Raptor 150gb sataII
# Drive(s): LG DVDr/CDr combo drive
# OS: Windows XP Home Sp2
# PSU: Ultra 500 watts
The main problem is that anytime I insert a cd/dvd into the drive and do something with it, such as installing programs or copying files etc., my computer becomes VERY slow and choppy and CPU usage goes to 100%. I have the HDD running to the 1st SATA slot, and the Combo drive running to the only IDE slot. Here's a screen shot of the device manager for this:
http://img174.imageshack.us/img174/1036/ender4aq5.jpg
For some reason the Combo drive will only stay in PIO mode, despite reinstalling the device and switching it to DMA, it always reverts back to PIO. I'm not sure if this has anything to do with the lag issue.
Another weird part about the screen shot is the SATA HDD is sitting in IDE channel. Shouldn't it be in the Serial ATA controller part?
I'm pretty new to this stuff, so please break it down into something I can understand, if you can help.

Quote from: Isiah on 14-March-07, 13:55:45
1. Is the drive flashed to the latest firmware?
2. Does it function correctly in other machines? (I transplanted a DVD-rom from machine to machine at work to re-install xp pro on one and the drive died somewhere in between)
3. Is the IDE cable attached firmly to back of drive and motherboard? (This can cause errors, crashes and other interesting phenomenem !)
4. Are did you re-install windows after changing motherboard?
5. Was is a DYI (do it yourself) build? <----------\
6. Are you a qualified technician or a home user? <---/\ = If you don't follow propper anti-static rules you will damage you components every time in some way, shape or form! (sick of people comming to me AFTER they have tried to do something themselves to save a few bucks and it ends up costing 100's or 1000's because they "thought" they knew what they were doing.)
1. I have no idea.
2. Yes, it worked in the same pc im using now, the old hdd was on the ide slot WITH the drive, and it worked fine. I just got the new SATA hdd, so I'm using that.
3. Yeah, cables are fine. The cable that goes into the SATA hdd seemed a little bent and was hard to put in, but I managed it so I doubt that's it.
4. I reinstalled windows on the new hdd.
6. Not really no.

Script crashes IDE and Flash Player but works in browsers

I'm building a game program and I've got a script that loads
an external swf, and then duplicates the clip for the user to play.
It worked until a few days ago when I reinstalled my OS (Mac OS
10.4.11) to fix an unrelated problem. The strange thing is that I
had reinstalled the browser plugin to fix a related problem. Now
the code works in the browser, but crashes the IDE and the Flash
Player every time. I called Adobe Support but they were no help
since it's "project related." I've reinstalled CS3 and Flash
itself, but nothing helps.
Here's the code that crashes:
// INITIALIZE LOADER AND ADD TO STAGE
var myLoader:Loader = new Loader;
addChild (myLoader);
myLoader.contentLoaderInfo.addEventListener (Event.COMPLETE,
isLoaded);
// DUPLICATE CLIP WHEN LOADED
function isLoaded (event:Event):void {
event.target.content.width = 100;
event.target.content.height= 200;
// THIS IS THE LINE THAT CRASHES
var copyClass:Class =
Object(event.target.content).constructor;
var newThing:DisplayObject = new (copyClass);
addChild (newThing);
newThing.x +=50;
myLoader.load (new
URLRequest('coloring/coloring1.swf'));

See this cool mp3 xml player with visualization, playlist and
skins. Fully customisable. Vector.
http://flashden.net/item/mp3-xml-strongplayerstrong-with-visualization-and-skins-vectorise d/11851

IDES and Model Company

I have installed IDES, and the model company data is not available. How to access Model company data? Im using SAP* and DDIC to enter into the IDES. Please provide steps in creating SAP user ID. Im particularly interested in using pre defined user id and the profile as mentioned in IDES help.
SUPER( SAP_ALL, SAP_NEW)
DEVELOPER( IDES_DEVELOP)
MUSTER( IDES_ALL)
JUNIOR( IDES_USER)
Is model company data accesible only using this USER ID and Profiles.
When I enter using SAP*, IDES shows only company code 0001. Apart from that no other data is available as stated in IDES examples.
I want to learn SAP SD through the IDES Model company. Please help...

-> which client do you use to login?
usually ides data lies within the 800/811 (?) client...have a look at table t000 (through scc4)
GreetZ, AH

I clicked on Sky go app to install on Sat .It is now Monday night and the app Icon is greyed out and displaying "waiting". Anybody got any ideas?

I clicked on Sky go app to install on Sat .It is now Monday night and the app Icon is greyed out and displaying "waiting". Anybody got any ideas?

Often, rebooting, or deleting the waiting app and re-installing, will do the trick.
Matt

[915 Series] SATA, IDE and the 915G.

Similar Messages

Maybe you are looking for