[925 Series] 925XE Neo Platinum Bios Update?

Bios Upgrade Wont Work !?! Any Ideas? I looked for Setting in Cmos protecting it and gone through Book but cant find any Jumpers
LiveUpdate 3.2 Says its done But on Reboot it restores to v1.3, Also tried Makin Boot disk And Using other Flashing Utils Still No Luck
If Protection is in the Bios Some Guidance to Disable it would be appreciated. The Mobo Says 925XE Neo (Ms-7053 v1) on it between PCI SLots

Boot Sector Protection Under Advanced Bios Features is Disabled(has always been disabled anyway), I even tried it on Enabled just so I can Say I did, But still don't work
Has Anyone Got any Ideas Please?

Similar Messages

MOVED: K8N NEO Platinum Bios Update - Memory Downgrade

This topic has been moved to AMD64 nVidia Based board.
K8N NEO Platinum Bios Update - Memory Downgrade

just switch back to bios 1.7

4Gb of RAM in a 925XE Neo Platinum, BIOS report 2.75GB?

Hi,
I've just replaced a dead motherboard in my PC with an MSI 925XE Neo Platinum (MSI-7053)
I needed new RAM for it (old board had DDR-SDRAM) and as it was cheap and the board supported 4GB, I got 4GB.
But the BIOS only reports 2.75GB of available RAM.
CPU is an SL7J8.
Can this be fixed with a BIOS update or something? Or am I stuffed?
Thanks,
J1M.

A part of your physical memory is being reserved by your BIOS, depending on the installed hardware. What's left is for the OS to add to the virtual address space (physical memory + pagefile), usually no more than 3.25 GB for a 32 bit OS. Decrease your pagefile in size to a couple hundred MB, it might change something and you will barely need it anyway...
If it's available in your BIOS, enable Memory Remapping.

K8N NEO Platinum Bios Update - Memory Downgrade

I have a K8N NEO Platinum MOBO, 2 GIG Ram with 1G in Each Dimm 1 and Dimm 2, Dimm 3 is empty. I have updated my bios from 1.7 to 2.1... With 1.7 my RAM runs at DDR400 no problem just like manual says. With 1.8, 1.9 or 2.1 I can only get DDR333???? What gives, anyone have the same problem.
Patriot DC DDR400 PC3200 2-3.2-5 Low Latency HP ram.

just switch back to bios 1.7

[925 Series] msi 925xe neo platinum issue

dear guys
i have just assembled my pc with the above-mentioned board but noted discrepancies with other 925-based boards when benchmarkings are performed. I understood that the same problem also occured with msi 915-based board but all seem to resolve with a bios update. When benchmarking are done with pc mark 2004, my ram marks only hit somewhere around 4700-4800, and cpu benchmarkings also are a bit low as compared to other boards with sisoft sandra 2005. Is MSI working on that or i just have to accept all this issues?
thanks in advance
btw, my pc specs: P4 2.8 GHz (FSB 800 HT-enabled), MSI 925xe neo platinum, A-Data DDR II 533 256 MB x2, Seagate 80GBs NCQ HDDs x2 as RAID 0, and Maxtor 80 GB SATA as RAID 0 and Optical drives.

I don't think it's the motherboard fault and its most likely due to the OS and hard drives. I had the same problem when I installed windows 98 and upgraded to windows 2000. I created a slipstreamed windows 2000 CD and installed windows 2000 from scratch and my problems stopped. Originally I was getting scores in 3D Mark 2005 of 4300-4800 and that was the graphics score. After installing windows using the slipstreamed CD I was getting scores of 5600. I think it was a SATA drive issue, which slowed down system and stopped it working as it should. Though you probably have windows xp installed from scratch I thought I would say this anyway as it kind of is relevant even though it's your CPU and RAM you're having trouble with.
You could try changing SATA ports or updating the drivers for the controllers if it's the SATA dirve to blame though I am sure other people will prove me wrong.
Is the CPU showing up at the speed it's supposed to?

K8N Neo Platinum bios 1.5 fixes matrox 450

K8N Neo Platinum
BIOS Type Award® BIOS File Sizes 311KB
Version 1.5 Update date 2005-1-21
Update Description - Support Matrox G450 AGP card.
- Update CPU ID.
- Support FX-55.
- Support Sempron CPU 1800+ GHz.
- Update NVRAID ROM firmware to Ver:4.60.
Special note ,
Download 7030v15.zip
http://www.msi.com.tw/program/support/bios/bos/spt_bos_detail.php?UID=572&kind=1

Quote
Originally posted by Supershanks
Guess MSI don't know their own boards
K8N Neo Platinum
May be theirs an "Optional adapter" somewhere
Thats what I said, didn't know the socket 754 board(my current board) support s939 platform...it would be cool though
Or maybe the same fixes apply to the Neo2 and they copy 'n pasted the info..

MSI 925XE Neo Platinum 54G Package contents

Hi to every body!
i bought a Nice MSI 925XE Neo Platinum 54G Motherboard but i think that the WiFi should have been included inthe delivery of my tower as on the receip it is stated as a 54g.
Has any faced any similar situation?
unfortunately the Retailer failed to provide me the box of the mother board at the delivery.
Could i, with the board serial number, find if and what was included in the retail box i suposely bought?
Anyway

thanx for the attetion Maesus
i bought my card on mid march for about 200 euros ex-VAT if this can give you an idea,
further more the thing that made me search was that the package was on the shop display and it is written on that a WIFI is bundel with
the serial should be 4C20240535 amoung all tha numbers written on.
thanx mate!

K8N Neo Platinum Bios 1.3 XP 3700 heat question

i did do a quick search on here before posting this question but had a load of varying answers ... so
i have a K8N Neo Platinum Bios 1.3 an xp 3700 and core centre says the chip is at about 45 - 50 degrees when the pc is idle
this is with the stock fan that came with the chip and ive also tried a samurai heatsink and fan .... ive reseated and reapplied artic silver and also tried thermal pads as well and the temp on the processor always comes back as 45 ish degrees
is this normal as the pc seems to run ok and even after round of doom 3 the temps only seem to hit about 55
are these chips hotter now or is it a bios / thermal temp issue
cheers guys
ohh and nice forums BTW

yup, issue with temp reading -> 1.43 beta bios for K8N NEO pL. for me 36-39 idle 42-45 after a doom3 session

Kingmax Hardcore DDR500 with MSI MS K8N Neo Platinum (Bios Version 1.40)

I am interested in Kingmax Hardcore DDR500 (PC4000) 512MB DDR-SDRAM. Currently, I’m using MSI MS K8N Neo Platinum (Bios Version 1.40) with AMD 64bit 2800+ & MSI MS 8907 FX5200-TD128 AGP Card.
Please advice whether the Kingmax Hardcore DDR500 (PC4000) 512MB DDR-SDRAM compatible with my systems.

The "safe mode" that the BIOS message refers to is not related to Windows' Safe Mode. The BIOS safe mode lets you un-do any overclocking or memory settings that might make your computer so unstable that you can't even get into the BIOS settings to change them. In that case, you hold insert while powering on to reset the BIOS to default safe values.
As for your problem getting into Windows' Safe Mode. If you upgraded from another motherboard that uses a different chipset, or if you somehow got the wrong chipset drivers installed, then the old AGP GART or chipset drivers will cause the system to halt/reboot very early in the Windows boot process even in safe mode. I've run into this problem before and its tricky. Best thing to do is switch back to the old motherboard, then go into safe mode and remove all chipset-related drivers, and then switch back to the new motherboard. If you can't do that, try running system repair from the windows setup CD. And failing that, you'd probably have to fully re-install the OS.

K8N NEO Platinum BIOS 1.8

I updated to this, only to find my machine would not boot to Windows. This, presumably because it was using 1T when, with two double-sided DIMMS, I require 2T. I couldn’t find anywhere to change that setting.
I noted on the boot screen that it was a workstation BIOS, and the flash utility is 859G rather than the usual 833C.
Got 1.7 on there now.
Have other people had trouble with this?

Quote from: Derek Baker on 27-August-05, 23:24:19
I updated to this, only to find my machine would not boot to Windows. This, presumably because it was using 1T when, with two double-sided DIMMS, I require 2T. I couldn’t find anywhere to change that setting.
I noted on the boot screen that it was a workstation BIOS, and the flash utility is 859G rather than the usual 833C.
Got 1.7 on there now.
Have other people had trouble with this?
me too.
K8N NEO Platinum MS-7030
Sempron 3000+ E6 64bit /no OC (200x9)
Samsung
Previous 1.7 BIOS is 2T Commandrate display on POST Screen.
1.8 Bios is 1T Commandrate display on POST Screen.
then, run Memtest86 1.55+ result no error on 1.7BIOS
but, run Memtest86 1.55+ result a lot of error on 1.8BIOS
Fixed no error to set Memclock to 166Mhz
I Replaced other memory.
I wish to select memory setup 1T/2T commandrate

Official, non-beta K8N Neo Platinum BIOS when?

Hi,
I see a lot of beta 1.5x BIOS releases for K8N Neo Platinum. Anybody know when the official release will come from MSI???
Thanks.

Quote
Originally posted by darthhen
Yeah I guess. It's hard to tell sometimes. I don't have the time to test out all the different beta bioses. I just want to update to the stable one.
yes but its also wrong to assume tha beta BIOS are unstable.in fact most these days are rock stable hence the fact they become official.

KA92 Platinum Bios Update

Hello. I have built a gaming system for a customer, and after a few weeks of use, it now will not consistantly pass the post test. I say consistantly, because 1 out of 7 or 10 times it will boot and then work fine, however most of the time it will fail the post with 1 long and 8 short peeps, which I have already researched. All parts were new, and nothing has been changed on this system. Yet the problem happened. I have cleared the CMOS, and removed the memory and have cleared all power through the system and still the problem persists. I believe that the bios version is 1.0 and the newest is 1.4. I was hoping that someone could provide me with clear instructions for doing the bios update to version 1.4 using a USB flash drive. The live update tool will not work as the system is running Vista 64bit SP1. All and of course the system does not have a floppy drive. System specs are listed below, and again please list the instructions in detail. Thank you for your help in advance, Todd.
System Specifications:
MSI K9A2 Platinum AM2+/AM2 AMD 790FX ATX AMD Motherboard
AMD Athlon 64 X2 6400+ Windsor 3.2GHz Socket AM2 125W Dual-Core Processor Model ADX6400CZBOX
2 sets (4GB - 4 dimms) Crucial Ballistix 2GB (2 x 1GB) 240-Pin DDR2 SDRAM DDR2 1066 (PC2 8500) Dual Channel Kit Desktop Memory Model BL2KIT12864AA1065 Seagate Barracuda 7200.10 ST3250410AS 250GB 7200 RPM SATA 3.0Gb/s Hard Drive
LITE-ON 20X DVD±R DVD Burner with LightScribe Black SATA Model LH-20A1L-05
LITE-ON 20X DVD±R DVD Burner Black IDE Model DH-20A4P-04
2 - MSI RX2600XT Diamond Plus Radeon HD 2600XT 512MB 128-bit GDDR4 PCI Express x16 HDCP Ready CrossFire Supported Video Cards

Quote from: BOSSKILLER on 17-April-08, 05:13:57
Don't use generic noname PSU, also avoid "Apevia".
Use quality PSU with powerfull large single rail good brand, like PC & Power Cooling, Corsair, Enermax e.g.
Good PSU suggestion with other info here:
https://forum-en.msi.com/index.php?topic=112039.msg836246#msg836246
Add-on to read:
PSU's---2 x 12v---The Dual Rail Myth
Is your problem caused by your PSU?
Unfortunatly I don't think that I can return it at this time. It has been more then 30 days. It bought it becasue it had a $50 rebate, but was still a $140 PSU before rebate. I didn't think that I was getting a cheap one, but I guess I was wrong. I usually only ever buy Thermaltake and occasionally Cooler Master. I have had good luck with both in the past. Thermaltake is worth the money in my opinion. If the Apevia goes bad again, then I will try to exchange for credit, but since I threw the orginal box away, newegg wouldn't work with me at this time. :(

Neo 2 bios update

my neo 2 865 pe reboots when i surf the web may a bios update to version 1.9 fix it where can i get the 1.9 bios

Use LiveMonitor, or LiveUpdate, or download from MSI site.
It might fix it, but since you don't say what you have in your system and how you are connecting to the net, who knows?

[Athlon64] MSI K8T Neo FIS2R BIOS Update when? CnQ no workie!

The MSI K8T Neo FIS2R (MS-6702) hasn't had a BIOS update since 3-4-2005!
I put a Sempron 64 3000+ in my motherboard, and was very disappointed that it is recognized as an "AMD Unknown Processor". Sure, it works, but one of the reasons I bought it is in the hopes of getting AMD Cool n Quiet to work. However, apparently the AMD driver can't recognize the CPU due to the old BIOS on the motherboard.
Every other MSI skt 754 board supports Sempron E6 revision already. Why not the K8T Neo FIS2R? Where have all the MSI BIOS programmers gone? I have been waiting 2-months for a BIOS update to support the E6 Semprons. I have asked and begged MSI Tech Support. I am tempted to switch to ASUS or some other company that is actually timely with BIOS updates. Only reason I haven't yet, is this board is everything I want EXCEPT for Cool n Quiet not working. It's starting to look like there is no BIOS update in sight, so I am very disappointed.
Anyone here work for MSI can confirm there are no plans for a BIOS update? Because I don't want to wait around for something that's not going to happen.

Sorry, I didn't mean to imply I thought the mods here are MSI staff... I was just kind of hoping there's MSI staff lurking here, seeing what people think of their products or seeing what people complain about.
No, pretty much C 'n Q is the only reason I'm disappointed, but it was something I was really set on getting to work since this is a server that's up 24/7, but isn't utilized but maybe 4hrs out of a given day. I could reduce frequency and voltage, but unlike C 'n Q, it won't automatically increase speed and voltage based on demand - which is something I want since although it's a server, I also use it as a regular PC as well.
I've even tried the 2.33 beta BIOS with no change, and even found a 5.52 BIOS in their BIOS testing directory. I guess that BIOS was for a different kind of 6702, although I had pulled out the peripheral modules with AMI's MMTOOL and they looked the same as the existing BIOS, but that BIOS killed my motherboard so it couldn't have been for a regular 6702. I had to desolder the BIOS chip with a heat gun, reprogram the old BIOS back on it with an EPROM programmer, and solder in a socket. I guess that shows my dedication to get C 'n Q working!

K8N Neo Platinum Bios 1.3 Question

This is bit of a dumb question..... I am not a noob either, been building computers for 6 years.
I have a K8N Neo Platinum with AMD64 3000, 1 GB Corsair Value Ram, 160 GB Western Digital ATA Drive, ATI 9800 Pro 128MB Catalyst 4.7, LG DVD Drive and NEC 2510A DVD burner, Windows XP Pro with SP 1a.
Tried to get into Safe Mode the other day ( to uninstall the video driver with Driver Cleaner) ...Hit F8 while booting , got the standard menu for safe mode, picked the standard "Safe Mode " option....then the computer restarts.
So I can't get into safe mode
I went back to the MSI website to get bios version again....then I saw this for Bios version 1.3 which I have on my board....
Quote
System reboot to safe mode when "Insert" key pressed
Does this mean, instead of hitting F8...you hit the insert key , or does this mean hit F8, chose the menu selection you want , then hit insert while it is going through the boot process.
Thought that I would ask?

The "safe mode" that the BIOS message refers to is not related to Windows' Safe Mode. The BIOS safe mode lets you un-do any overclocking or memory settings that might make your computer so unstable that you can't even get into the BIOS settings to change them. In that case, you hold insert while powering on to reset the BIOS to default safe values.
As for your problem getting into Windows' Safe Mode. If you upgraded from another motherboard that uses a different chipset, or if you somehow got the wrong chipset drivers installed, then the old AGP GART or chipset drivers will cause the system to halt/reboot very early in the Windows boot process even in safe mode. I've run into this problem before and its tricky. Best thing to do is switch back to the old motherboard, then go into safe mode and remove all chipset-related drivers, and then switch back to the new motherboard. If you can't do that, try running system repair from the windows setup CD. And failing that, you'd probably have to fully re-install the OS.

[925 Series] 925XE Neo Platinum Bios Update?

Similar Messages

Maybe you are looking for