[945 Series] 945P Platinum and core cell :(

HI!
Anybody tell me some issue about core cell and the 945P??
core cell does'nt work at all...My two board fans ( 120mm) turn a 2300 rpm and the cpu fan 2400 rpm !!! With my big Zalman, Idle time, the cpu ( INTEL 820) is very cold! 27 degres....!! Samething at 3000 mhz....
I would like to know if a patch is available ( I have the last one core cell at the MSi site) or if someone can give me some alternative...
My house is like an airport right now...you can imagine how!
Thank you!

 Core Cell doesnt have a good rep on here...many problems. If i were you i would try out SpeedFan. You can download the program for free and it will ajust all your fan speeds for you after you configure it. It lets you set the temps and speeds, along with monitoring them for you. Just google SpeedFan and use the help section for the walk through on the configuration. Good Luck with your airport 
Post back with questions 

Similar Messages

  • 945P Platinum and Pentium D 945

    Did anyone try Intel Pentium D 945 CPU on the 945P Platinum motherboard? Does it work with bios 1.6?

    Quote from: Maesus on 09-March-07, 19:50:58
    oh well, there is no good reason why D 945 is not supported by 945P. Just make sure you have the latest BIOS.
    Once I've seen OK on the CPU Support Page for the Pentium D 915.. Maesus do you think I should try?  ???

  • [945 Series] 945P Neo will not Post

    Hi all!  I have a 945 Neo Board with an Intel Pentium D processor.  I also have 2 GB of RAM, a PCI-E RadeonX700 vid card, a SATA HD, and DVD burner.  It is in an Antec case w/ 350 W power supply.  I have a ps2 kb and mouse.  I put it all together last night and the Black screen begins to boot.  It detects the processor, the full amount of RAM, and the DVD burner and HD.  Then I get a series of continuous beeps and a message that "keyboard cannot be detected"  The BIOS then sits there asking to press DEL to enter into it.  Obviously I cant because it does not detect the KB.  I tried removing one stick of ram, and then I tried removing everything from the board except the vid card, kb and mouse.  This is all to no avail.
    As far as the power supply it only had the four prong connector instead of the eight that is on the board.  I did plug the four prongs into the eight prong connector.  Could this be the issue?  Is the adapter necessary?  Or is it a different issue?  Any help would be appreciated because I am going nuts!! 

    Well I have only tried to post this new mobo. ( Just to look around the BIOS)
    I am still whiting to get my New PSU and HS&F.
    I think my problem is similar to yours. Right now I'm using a P.O.S. PSU w/ a 20pin to 24pin adapter & only one P4 plug.
    The mobo comes on for a few seconds then powers down. (Probably because of this POS PSU)
    Once I get the new parts in the mail I think I will be fine.
    There is a little more info on my New system in the tread
    https://forum-en.msi.com/index.php?topic=92545.0

  • 945P Platinum and 530J P4 speed fan problem

    Hi,
    i cant find 4pin selector in BIOS. The problem is, that CPU fan is going at 3115 rpm and rpm never goes lower. CPU temp is 32C. When temp is 40C, CPU fan goes 4500rpm. TOOO noisy. On 915P Platinum (with 530J but other orig. p4 cooler- i see differences) there is CPU fan very good, if CPU get loaded, fan speed goes up, but if you end work, CPU is in a minute at <2000rpm and I almost cant hear it.
    Any ideas?
    Thanks
    P.S. Excuse my english

    problem solved, i switched on Legend Thermal Control in BIOS...

  • [945 Series] 945P Overclocks

    Anyone out there with the 945P? Post your overclocks! I want to see what results people are getting.

    Quote from: Din on 03-September-05, 02:34:33
    OC is accordingly RAM,PSU and cooling system... and ofcourse the CPU. The OC options of LGA775 mainboards are ~ same
    What does that have to do with my question? I just want to know people overclocking results.
    Also am I missing something or does the 945P not allow you to lower the multiplier of the 630 chip like the Asus P5AD2-E? and you can't run a 1:1 ratio with PC2-4200 memory to overclock to the stock 533 speed? In the memory setup you can only use 533 and 667.

  • Core Cell user settings drives me mad

     :O  :O  NEO2 Board with i865PE and Core Cell
    Hi MSI Crew!
    It is completletly annoying, everytime my pc boots up, the settings are default very high revalations/seconds to nb and cpu fan, that meens VERY LOUD! So I adjust them manually to "low-1" and the system works fine, but when the next reboot comes....it stays at "full speed". I hate this, really, it sucks. And the automatic function will only give some kind of police horn: low-high-low-high  -unusable.
    Even with the latest update no fix.
    So please please please make the settings permanent.

    thank you for your reply but i solved the problem I needed to
    type _root infront of the getURL code.

  • P6N platinum and Dual Core Center

    Hi,
    When I attempt to use the Dual Core Center I get an error:
    0xc0000005 Program failed to start, press OK to end.
    I have updated the BIOS, Dual Core Center, Nvidea drivers, .NET framework etc no change.
    Tech support told me that the Dual Core Cell chip on the board was bad so I got a second board without change.
    I really don't care about the OC'ing features, I want to monitor temps and control fans.
    I have tried Speedfan, it does not control the fans plugged to the mobo headers. Neither does Nvideas tool (Nview).
    Infact nothing I have tried will control the fans.
    Suggestions?
    (Aside from returning both boards and going with a different brand)
    Components List:
    MSI P6N SLI Platinum LGA 775 NVIDIA nForce 650i SLI ATX
    EVGA 256-P2-N740-LR GeForce 8500GT 256MB GDDR2 PCI Express x16
    FSP Group (Fortron Source) AX450-PN ATX12V 450W Power Supply
    Intel Core 2 Duo E6600 Conroe 2.4GHz LGA 775 Processor
    Crucial 2GB (2 x 1GB) 240-Pin DDR2 SDRAM DDR2 667
    SAMSUNG SpinPoint T Series HD403LJ 400GB 7200 RPM SATA 3.0Gb/s
    SAMSUNG DVD burner
    MAXTOR 40GB HDD (PATA, moved frmo old PC for transfer of files)
    USB Wireless Network
    Windowx XP Home, SP2

    Quote from: Maverick0984 on 20-July-07, 22:44:21
    I think the program is horrible...don't waste your time with it.
    If it works, good! It doesn't tend to fuss.
    But if it doesn't work, uninstall it.
    CoreTemp and Everest like Jack says are the best.
    Fan speeds however your out of luck with. You can submit a report through Speedfan to the author however.

  • Dual Core Center- MSI P6N SLI Platinum and MSI 8800 GTS 640

    I have both the MSI 650i MOBO and the MSI 8800 GTS vidcard. When using an Asus P5B Dlx MOBO and this vidcard, Dual Core Center was installed and displayed the information for the videocard and allowed a mild OC. Now with both MSI products in the case, Dual Core Center only displays the information on the MOBO-- no 8800 GTS information. The tab at the top for the VGA does not bring up anything.  ??? I have tried installing the version on each one of the disks that came with each piece of equipment again and it doesn't seem to make a difference, it doesn't work. I downloaded the most recent version of the utility from the MSI site and still get only the MOBO information. How do I get the display for the video card.
    Or since the MSI utilities typically are listed on the forums as not being the greatest, what else can I/should I be using instead?
    {I'll put this in the graphics forum too as it hits both areas...}

    Running a P6N SLI Platinum and a MSI 7900GTO with Dualcorecenter 2004 and everything is ok.
    Never installed any driver from the MSI CD which comes with the board or graphics card. All drivers are downloaded
    from Nvidia.
    Maybe the 8800 series is not supported yet.

  • Intel Core 2 Quad Q8400 to 945P Platinum?

    Hi, i have question.Is possible aplicate processor Q8400 to motherboard 945P platinum?I downloaded the newest BIOS file W7176IMS.230 for 945P platinum, but i didnt find cpu support.Thx a lot.

    >>Posting Guide<<
    Your specific processor does not appear on the CPU support list.
    http://us.msi.com/index.php?func=prodcpusupport&maincat_no=1&prod_no=193#menu
    Suggest you contact >>How to contact MSI.<< MSI technical to check if there is any intention to do this. I doubt that they would do any further work on a BIOS on a discontinued MB.

  • 945P Platinum, memory divider (BIOS)

    First I want to say hello to all users!
    I recently bought MSI 945P Platinum motherboard with Bios v1.3, CPU is Intel Celeron 2.66GHz, 64bit, LGA775, 256mb cache which I intend to replace with some Pentium D in about a month. But until than I tried to overclock CPU but all I achieved is 145*20=2.9GHz (default is 133*20=2.66GHz) Vcore 1.4v, with Kingston VR DDR2 533MHz memory. The thing is that FSB:DRAM is always 1:2, how can I change this in bios? I think that the problem is memory, it wont go more than 580MHz... and if I put FSB at 146 the only solution is CLEAR CMOS.
    I didn`t tried with different bios versions because there are no other versions to download from msi.com.tw.
    P.S. I also tried to set in bios>core cell>memory manual 4-4-4-11 533MHz but nothing happens, I cant change FSB:DRAM from 1:2.
    Please help.
    Thanks in advance.

    You can.
    The o/c method goes like this: Every 1 FSB rised = 2 RAM MHz rised. If your 2.66GHz Celeron is 133 x 20, 133 is the FSB and 20 is the multiplier so your RAMs will be 266 x 2, where 266 is the RAM speed and Double Data Rate 266 will give approx. 533MHz. We'll only take the FSB and the RAM speed here for divider calculation.
    133 : 266 will ratio as 1 : 2. If you want to o/c higher in terms of CPU speed, you can try dropping your RAM speed to 200MHz and rising the FSB to higher clock speed. This will allow the RAM speed to increase as well.

  • Problem overclocking my 945P PLATINUM+805D

    hi...
    my english is lack so i'll make it slow
    i just bought the msi 945p platinum with intel dual 805d.
    unfortunally, i cant o/c the system ..
    the bios got no update on msi website so i see it is the latest bios .
    i know that the 805d can be o/c to 3.2 without any over voltage ...as concidered to other motherboards .just by increasing the fsb to 166.
    i am kind of newbie in the terms of o/c .
    i tried to make some adjustments in the corecenter software but the system freezes or get quickly unstable.
    i cant make the fsb on bios ,higher then 165 .default is 133 by the range.
    i put over voltage to the memory ->1.9v .default is 1.8 , and put the fsb to 165...but the system didnt post .
    anyone here can help me please ?
    ms spectrum :
    805D
    MSI PLATINUM 945P
    OCZ GOLD EDITION 667 DD2 5400 4-4-4-12  . 1 GIGA KIT.DUAL CHANNEL.
    ATI X1300PRO 256M
    CHENBRO GAMING BOMB
    PSU 350W everpower true power / 18A on one rail 12v

    Quote from: emankov on 27-May-06, 01:52:50
    I also have a D805 and an 945P platinum.
    In fact i manage a 3.3 GHZ stable overclock by using these:
    In BIOS cell menu:
    CPU ratio unlock-unlock
    Memory function sub-menu - Enter, then
    DRAM timing - AUTO (!!!!)
    System memory frequency - auto
    D.O.T.3 Step0 setting - disabled
    Auto Detect PCI clock - Enabled
    Spread Spectrum - Disabled
    CPU fsb frequency - 165 (THIS IS THE MAX THAT MOBO PERMITS AND IT PISSES ME OFF) 
    PCI-e frequency - 115
    CPU voltage - 1.21V (1 step up from normal)
    Memory voltage - 1.8V
    AGP/PCI voltage - 1.5V
    I have to say that i use a ZALMAN 9550 heatsink and a pair of OCZ DDR2/667 dual channel. CPU temp as BIOS shows is 42C
    Also, memory is not overclocked at all !!!
    PSU is a TAGAN 500W
    I am sure that i could go up to 3.6-3.8 GHZ with a board that is more "overclocking" oriented.....
    But alas...i have no other problems (so far) from it 
    thanks for the post 
    exact vallues are very helpful even  though ıt ıs not mathematıcal ıssue ...
    for the guıdıng lıght to get thıs mobo hıgher .
    as your values ın same hardware .. ı got a 3.3 805D .. ı  see thıs mobo ıs lıttle bıt problematıc wıth OC .
    thanks agaın 

  • 945P Platinum IDE 2 & IDE 3 works in PIO MODE?

    Hello there, I just Bought MSI 945P Platinum M/B and Intel Pentium 4 D @2,8Ghz with 1Ghz RAM, 80GB SATA2, 4 CDRW drives (PATA) where 2 of them I plug in to IDE1 slot(known as RAID, but i configured it to IDE function in BIOS) and the others are in IDE2 slot. I used winxp with the all M/B driver installed, everything's seems ok in device manager, the problem is when I use nero for burning with multiple recorder activated, the windows then going extremely slow in any response even with the mouse movement that it seems windows is running out of system memory. Then I check the device manager and I found that IDE2 run in PIO Mode, IDE1 run in UDMA Mode2.
    It didn't make any changes when I used IDE3 slot, it run in PIO MODE either.
    How Can I configured The IDE2 & IDE3 to works in DMA mode? I've try any combination in BIOS Setup... it didn't work??
    HELP, any advice would be appreciated THX...

    PCI Bus Mastering already enabled since the 1st time I configured the bios, I'm using 2 pieces thermaltake IDE round Cable that plugged in to IDE 2 & 3, IDE 1 using cable that came with the board. I'm using 4 LiteOn PATA Writers and Seagate 80Gb SATA2 HDD plugged in SATA1 port.
    1st configuration, 2 writers are in IDE 1 & the others are in IDE 2
    2nd configuration, 2 writers are in IDE 1 & the others are in IDE 3
    3rd configuration, 2 writers are in IDE 2 & the others are in IDE 3
    All above configuration make the same result, IDE 2 & 3 Won't run in DMA mode
    I've try to switch the thermaltake cable to IDE1 and it's work fine (DMA still on).
    It doesn' t matter how I configured the BIOS (SATA to combine, enhanced, or AUTO) IDE2&3 still in PIO Mode.

  • 945P Platinum No Manual Bios Download

    Anyone help why MSI took off Manual Bios Downloads for 945P Platinum Version Boards
    I like to Manual Update Board Bios to latest Bios before Loading OS and view current Version releases (without LiveUpdate)
    Also anyone experienced Microphone Problems plugging into Mic Plug (Onboard Realtek 882) all version Sound Drivers
    Low Voice pick up (Skype or Sound Recorder) have to use USB Mic
    Have tested on 10 Different Boards and differnet plug in mics all the same

    Not unusual that bios is removed / greyouted, when there are just the original 1.0 bios and no update versions.
    Have you been able to download newer/later biosversions then the orginial bios before ?
    No clue about the mic-port issue.
    Sometimes separate pci soundcards gives better functionality.

  • Difference between 6 Cell Li-iion Cyl HC Rear (72Wh) and 6 Cell Li-ion (47Whr) Cylindrical

    Hi Tech teams,
    I went to the lenovo site to customize a T440S Thinkpad and got stuck at the REAR BATTERY selection. I have searched in google and the site and could not see the picture difference's between 6 Cell Li-Ion Cyl HC Rear (72Wh) and 6 Cell Li-ion (47Whr) Cylindrical. I know those will be large and will bulge out of the laptop.
    But I would like to understand in which way and want to see the pictures of the laptop fitted with these 2, so that I can proceed with my order. Will it come out like a cylindrical bulge at the back of the laptop or at the bottom it will have an extra step like thing. Why dint the lenovo put 3 different pictures showing the laptop with these batteries in the "help me decide" option while customizing the laptop. That would have been very nice to the customers. I have wasted 2 hours to compose this and search everywhere, without any resolution. I found a similar thread in some forum, asking for the pictures, and no one replied him as well. Please see the below screenshot.
    Thanks
    Manu

    Hi,
    look at Notebookcheck review
    x220 | i5-2520m | Intel ssd 320 series | Gobi 2000 3G GPS | WiFi
    x220 | i5-2520m | hdd 320 | Intel msata ssd 310 series | 3G GPS | WiFi
    Do it well, worse becomes itself
    Русскоязычное Сообщество   English Community   Deutsche Community   Comunidad en Español

  • K9n2 sli dual core cell problems

    I just installed my new motherboard ,update drivers for the 750a and my gtx 260 . i installed dual core cell utility , reboot . when my os (vista 32 bit) load firewall , anti-virus,  the system lock , everything stop working , i must reset the pc go in fail safe mode and uninstall dual core cell. why?

    Quote from: BuD_Sp3NcER on 21-January-09, 15:33:55
    You have to ask yourself: Why do you like it?
    There are many other Apps out there that could do the job of DualCore Center.
    i know , i unable to use dual core, i can't says i like it. it's just a little question , no need to worry 

Maybe you are looking for