970A-G46 CTRL-F doesn´t work.

Hi,
I have build a new PC with this MB and two Kingston HyperX SSD. I would like to create a Raid1 but
if the system shows the two drives and "press CTRL-F to enter Raid" and I do it, nothing happens. Any hints?
In BIOS SATA Raid and Legacy ROM are enabled.
Best Regards,
Freddy

Make sure to not hold CTRL once it boots, but do actually press ctrl+f once it shows. I was holding Ctrl upon boot and when screen popped up, I was pressing F into it and didnt work.

Similar Messages

Ctrl+enter doesn't work

ctrl+enter doesn't work when I try to go to maps.yahoo.com. It only happens when I try to go here. ctrl+enter works for every other site I've tried.

That is a known limitation if you only use maps.yahoo (maps.yahoo.com should work though). 
Ctrl+Enter to fixup the URL and add .com only works if there is one domain (yahoo) and not with multiple domains (maps.yahoo).
*[https://bugzilla.mozilla.org/show_bug.cgi?id=688395 bug 688395] - CTRL+Enter does not append .com after getting a server not found error

CTRL+break doesn't work, cannot boot on Rommon.

GoodDay to All,
Im using a 1750 router, and then i upgrade it to higher version, after
then i reload it, the problem it does not goes to start-up mode or
even the rommon mode,not enough memory to load the image, it always
rebooted after the self-decompressing image,
I try to stop it using the CTRL+Break, but it doesn't work.
Here are the error message.
Smart Init is disabled. IOMEM set to: 20
Memory required: 31637548 bytes, Memory available: 25165824 bytes
INSUFFICIENT MEMORY TO LOAD IMAGE!
The difference between Memory required and Memory available is the additional
memory you need to run the router. Alternately, use a smaller image; this
may cause the memory requirement to decrease, and may allow you to at least
use the router with reduced functionality until you get more memory.
*** System received a Software forced crash ***
signal= 0x17, code= 0x200, context= 0x8000620c
PC = 0xffffffff, Vector = 0x200, SP = 0xffffffff
System Bootstrap, Version 12.0(3)T, RELEASE SOFTWARE (fc1)
Copyright (c) 1999 by cisco Systems, Inc.
C1700 platform with 24576 Kbytes of main memory
program load complete, entry point: 0x80008000, size: 0x6b4628
Self decompressing the image : #################################
################# [OK]
Smart Init is disabled. IOMEM set to: 20
Thanks,
Lester

Hi Lester,
After trying all the above suggestions, if you still are facing issues then open the router's box and take out the Flash SIMM... it will try to look for an IOS file thrice and then will fall into rommon automatically
You can use the following link for hardware installation:
http://www.cisco.com/en/US/customer/products/hw/routers/ps221/prod_configuration_guide09186a0080099429.html#wp1077820
After you are in rommon, issue the command "confreg 0x2100" and "reset" the router, you will again go into rommon
Then insert the FLash once again in the chassis and then bootup again, because of config-register 0x2100, the router will go to rommon and then you should check the new IOS that you are trying to install.
Your router should have sufficient amount of DRAM to load that IOS, infact it'll help if you post the exact file names of the previous IOS and the new IOS along with your routers DRAM and Flash Capacity (But this is a secondary task which we can think of once you are able to go into rommon)
Regards,
Neeraj

Ctrl+C closes tab instead of copying text and Ctrl+F doesn't work

Hi,
As stated in title, since upgrading Firefox to the latest version, when I press Ctrl+C it closes the tab I'm on instead of copying text. It can be text from a website or text from an email i'm writing. Estremely frustrating, as I've come to the habit of copying the text of an email I'm sending using Yahoo Mail before sending in case it doesn't send properly and gets lost!!!
Also, I usually pressed Ctrl+F to search for a specific piece of text on a website, but this simply doesn't work. Any ideas?
I use the Welsh language version of Firefox, and the same problem occurs on both my home laptop and work PC.

Super annoying, but I've realised '''Ctrl+Shift+T''' opens the last tab to be closed and that is a great help until a fix comes along.

CTRL+RMB doesn't work any more on Firefox4.

[http://www.lingoes.net Lingoes] translator uses CTRL+RMB to capture text. It doesn't work any more on Firefox4. Why? Is it possible to restore it? Thanks!

Thanks for your answers!
I found out, that only on the US site Expert Mouse there is no software for Lion.
(The one you can get there is from 2006!)
But I found suitable TrackballWorks software on the Kensington UK site
http://eu.kensington.com/kensington/en/gb/o/15/sku/498/64325/kensington+expert+o ptical+trackball.aspx
of 2010 and a Beta-version of July 2011.
Since the 2010 version works fine under Lion I'm happy with it.
I hope this will also help others with problems with old Kensington software.
Thanks again!

CTRL+Z Doesn't Work in Direct Link

So...oddly, CRTL+Z for undo doesn't work for me when I'm Direct Linked. My UI pulls up the Timeline window though (as in settings not actual timeline) which doesn't do anyone any good because you can't adjust anything there anyway
Thoughts? Anyone else?
I'm on Win 8.1 (HP ZBook) - latest updates in Adobe across the board.

Hi!
Sometimes I also have this problem, which is very annoying. I did not find out, why it happens.
However a restart of speedgrade helps.

CS3 Bridge will not launch tried 'ctrl' icon doesn't work.

Adobe Bridge has encountered a problem and needs to close. We are sorry for the inconvenience.
this is the message I get when i try to launch Adobe Bridge -
I called tech support & although I've spent $$$ for master collection CS3 - and so many other adobe programs/software for myself & others.. they are unwilling to offer any support other than a paid issue, which really chafes.
so here I am, throwing seeds into the wind hoping i can get back to work after wasting a nother day with this this.
there is no phantom instance of Bridge.
I have a wacom tablet. I cannot get to any 'preferences' screen with any combination of ctrl, alt, ****..
Bridge will not launch.
Help please? thanks

Curt Y answered this in another thread;
If you can not get the reset window, you are doing something incorrectly.
1. Bridge has to be closed. Check the Task Manager to make sure no copy is running in the background.
2. You have to press and HOLD the Crtl key when you click on the start icon for Bridge.
3. If successful you will get a reset window with 3 options.
in this thread;
http://forums.adobe.com/message/2735898#2735898
the key point is step 2 HOLD... this is nowhere else in the forums..
so, again, thanks to Curt Y for the answer/
I checked all three boxes & Bridge did launch. Why is this so obscure.. and why could tech support just tell me that..
oh well.
again. thanks.

My ctrl button doesn't work with other keys

Hello: I am unable to use the ctrl+t (open new tab), ctrl+c or ctrl+v (copy/paste) among other ctrl commands while using firefox. I know that the ctrl key itself is not broken as I am able to use the ctrl+backspace and ctrl+forward (return to last page viewed) functions.
Many of the help sites I've seen focus on uninstalling the ask.com toolbar. I uninstalled ask.com toolbar once, and the ctrl key started working again. The problem came back within a week, however, and ask.com is not a factor anymore as it has already been uninstalled. What else can I do to fix this problem? Any advice would be appreciated.
I have already tried restarting firefox in safe mode, and this did not solve the problem.
J

Start Firefox in [[Safe Mode]] to check if one of the extensions is causing the problem (switch to the DEFAULT theme: Firefox (Tools) > Add-ons > Appearance/Themes).
* Don't make any changes on the Safe mode start window.
* https://support.mozilla.com/kb/Safe+Mode
* https://support.mozilla.com/kb/Troubleshooting+extensions+and+themes

My ctrl button doesn't work with many other keys

Hello: I am unable to use the ctrl+t (open new tab), ctrl+c or ctrl+v (copy/paste) among other ctrl commands while using firefox. I know that the ctrl key itself is not broken as I am able to use the ctrl+backspace and ctrl+forward (return to last page viewed) functions.
Many of the help sites I've seen focus on uninstalling the ask.com toolbar. I uninstalled ask.com toolbar once, and the ctrl key started working again. The problem came back within a week, however, and ask.com is not a factor anymore as it has already been uninstalled. What else can I do to fix this problem? Any advice would be appreciated.
J

Start Firefox in [[Safe Mode]] to check if one of the extensions is causing the problem (switch to the DEFAULT theme: Firefox (Tools) > Add-ons > Appearance/Themes).
* Don't make any changes on the Safe mode start window.
* https://support.mozilla.com/kb/Safe+Mode
* https://support.mozilla.com/kb/Troubleshooting+extensions+and+themes

I can't open any new windows from File [New Tab] and from clicking on [+] , as I usually did. And [Ctrl+T] doesn't work for me.How I can make it to work for me again, please?

I have to open the next window by right clicking on some link from previous site, who gives, '''''from drop down menu''''', option to [Open link in new tab] and then I can use that "fresh" tab.
It is my desktop, if it's important to know for help.
Please, some ideas, how to fix it, will be welcome.
Thank you.

Hi, were you able to resolve your problem? If so, please mark this question as '''Solved'''. Thanks !

I cannot open a new page. ctrl + t doesn't work, or the block next to the current page. nothing works.

When I follow a hyperlink, a new page will appear.
And when after I closed Firefox, I open again Firefox all pages, which were open, will reappear.

This issue can be caused by the Ask.com toolbar (Tools > Add-ons > Extensions)
See:
* [[Troubleshooting extensions and themes]]

Adobe reader X (10.1.2) Zoom and Copy doesn't work

Hi guys,
I installed Reader X yesterday and now I'm stuck with these 2 problem
I cannot zooming by using ctrl+mouse wheel (up or down), zooming with ctrl+(plus or minus) still work. This feature also work fine on FireFox, Chrome and other programs. In addition, I cannot left click to drag pages down with hand tool.
Another problem is everytime I copy text from a pdf file, there is a message that "There were an error while copying to the Clipboard. An internal error occured".
All above features works fine on Reader 9 and older versions. I'm using Windows 7 Home 64-bit.
Please help

v10.1.3 seems to solve this issue, but...
For me Ctrl+minus doesn't work... it confuses it with Ctrl+6
Maybe because I'm on AZERTY keyboard and - and 6 are on same key

SOLVED - English thesaurus doesn't work in OpenOffice Writer 3.2.1

I'm using OpenOffice Writer v.3.2.1 in current Arch Linux. To enable spell and grammar checking and for a thesaurus, it appears one has to install the appropriate extension(s). I did that by going to Tools -> Extension Manager, selecting Add, navigating to /usr/lib/openoffice/share/extension/install, picking the dictionary "dict-en.oxt" (file dated 6/1/10) and clicking Open. That installed the "English spelling and hyphenation dictionaries and thesaurus 2010.03.16". Spell-checking and hyphenation do indeed work and are supported through the Hunspell SpellChecker and Libhyphen Hyphenator, resp.
However, with this extension, the thesaurus doesn't work. In Tools>Language, the entry "Thesaurus" is greyed out and CTRL+F7 doesn't work. In Tools>Options>Language Settings>Writing Aids, under "Available language modules" no thesaurus or grammar modules are listed. When I press the "Edit" button in that dialog box, the categories Grammar and Thesaurus are there but no specific modules are listed for them. No separate English thesaurus appears to be available at http://extensions.services.openoffice.org/en/dictionary .
How can I get a decent thesaurus to work from within OOo Writer?
EDIT: To be able to use the thesaurus requires installation of libmythes. Thanks to Robert Tucker for pointing out the fix.
Last edited by RobF (2010-08-09 21:46:51)

erdk wrote:Hmm, I've also have newest kernel with bumblebee, bbswitch and nvidia, but instead of normal versions I've installed dkms-* packages (dkms-bbswitch and dkms-nvidia) - so when new kernel arrives these modules are automatically rebuild to match new kernel. You should reinstall this two packages (bbswtich and nvidia) - they be build against new kernel and everything should be ok
Yes, the dkms versions work fine with the new kernel
Thanks!

Tracker doesn't work in deskbar-applet

Hi again, one more problem.
I used to use a lot the spotlight-like tandem deskbar-applet + tracker; but after the upgrade to Gnome 2.24 it doesn't work for me anymore and it looks like i'm the only one that uses it or, at least, that has this problem.
I followed these instructions but nothing happens. The other deskbar plugins happen to be like
/usr/lib/deskbar-applet/modules-2.20-compatible/wikipedia-suggest.py
/usr/lib/deskbar-applet/modules-2.20-compatible/wikipedia-suggest.pyc
/usr/lib/deskbar-applet/modules-2.20-compatible/wikipedia-suggest.pyo
I tried placing module-tracker.py in that directory but again nothing happens and cannot find the files tracker-module.pyc nor tracker-module.pyo. As google tells me at least tracker-module.pyc should be created automatically the first time tracker-module.py is run. I tried to force it and here is the result:
[pablo@pablerkas modules-2.20-compatible]$ python tracker-module.py
Traceback (most recent call last):
File "/usr/lib/deskbar-applet/modules-2.20-compatible/tracker-module.py", line 14, in <module>
import deskbar.core.gnomedesktop
ImportError: No module named gnomedesktop
[pablo@pablerkas ~]$ sudo modprobe gnomedesktop
FATAL: Module gnomedesktop not found.
I googled again with that but found nothing helpful...
Thanks in advance.
Plus: keybindig <ctrl>space doesn't work...
Last edited by Slurp (2008-10-30 12:45:36)

ok i have patched the script, but...
the script works but if I restart X or simply restart the deskbar, the script is not shown in the list (even if I use the reload button).
I have to recopy the script (from a backup dir) to the /usr/lib/deskbar.../modules.../ dir and it magically works, until the next reboot....
note that the script is in /usr/ so it cannot be modified by my user (and deskbar)
Can you confirm this?
I can make a script that copy the script everytime gnome boots, but it's not a good idea...

Ctrl + click doesn't select ALL non-transparent pixels

Hello. How can I select ALL non-transparent pixels from a layer?
- Ctrl + click doesn't work (it seems to have a 50% tolerance - my opacity 7% and 40% pixels don't get selected);
- The magic wand tool with 0% tolerance does work (when I click on a transparent pixel it selects ALL opacity 0% pixels around it and then I just have to inverse selection), BUT my image has a lot of holes with transparent areas and selecting them one by one would be tedious.
Thank you.

I think it should. if your only going by the selection outline, then the selection outline only shows the pixels that are 50% or more selected.
In other words the pixels have varying degrees of transparency. If the selected pixel is not at least 50% opaque then the selection outline doesn't show them, but they are selected when ctrl clicking on a layer thumbnail.
After making the selection by ctrl clicking make a new layer and fill the selection with black and then turn off the visibilty of all the other layers.
You should get a better idea of what is happening.If you were to lock the transparency of the layer and fill with black you should get the same result.
If you use the magic wand at 0% tolerance then your not getting a true selection of the layer transparency, but rather making the partially transparent pixels fully opaque (selected).

970A-G46 CTRL-F doesn´t work.

Similar Messages

Maybe you are looking for