975x - "Unknown Hard Error " STOP during RAID XP install

Hello guys,
I've got a new 975x Platnium system I'm building and I have an issue.
I've got 2 SATAII drives and I want to RAID 0 them.
I've made a ICH7R floppy and use the F6 method during the setup ... this (seems to) work fine, as the CD installation of XP kicks off and goes all the way through to GUI mode ...
However, during the 'installing devices' part for the GUI set-up (just before you would enter the Regional Options), the system fails with an 'UNKNOWN HARD ERROR', followed by a STOP error ...
Now, if I scrap the RAID and just install on a single drive, it works every time without fail ...
It's still pretty much barebones system ... CD-Rom, 2 SATA II drives, 2x1 gig OCX memory ... the graphics card is a Sapphire x1900
Anyone have any ideas why this could be failing ? ... odd that is should work on non-RAID and then give up during the RAID setup ...
Let me know ...thanks,
Spencer Steel

Yes - i did try it with XP with SP2 .. although, I couldn't actually get a boot from my XP SP2 CD at system level, I had to go in with XP SP1 and then run the SET.EXE for XP SP2 from there ... not pretty, (but it did occur to me that SP2 might have the drivers) ... the end result was the same though.
I'm still a little hazy in the RAID config. itself ... I mean, I've got the PowerUp Premium board and there are 4 'normal' sata connections on the board and one 'special' on - which I think is the JMicron controller.
I've put my 2 drives in SATA1&2 (normal!) and used the ICH7DH drivers during the f6 setup ... i did also add the JMircron controller as well during one attempt, but no joy.
Is this the best solution? Why/when would I use the Jmicron slot? The documentation is not exactly helpful !
Running fine on one disk - would love to be able to RAID it though ...
Let me know your thoughts .... thanks for helping....
S.S.

Similar Messages

Unknown Hard Error when installing Windows XP?

Ok first off I tried installing Windows Vista Home Premium on my new 24in iMac and after installation had problems installing drivers. Found out it was because I had a 64 bit version of Vista and the iMacs dont support that. Then I got a copy of XP Home Service Pack 3 from a friend to try. Im not sure if it is 32 or 64 bit but I was going to try it anyways. Its starts to extract the files and get ready for the install but not long after it does that it gives me an unknown error and the blue screen of death.
"STOP: c0000221 Unknown Hard Error
\SystemRoot\System32\ntdll.dll"
Does anyone know what this means? I would really like to get one of them installed. I dont care which one...if anyone knows how I can put a 64bit version of Vista on my iMac that would probably be best since it installed fine and just messed up when installing the drivers. Otherwise can anyone tell me what to do about this unknown error? Or do I need to search around for yet another operating system cd?
Any help will be greatly appreciated.

Hi KadeP,
there is indeed not a solution for that CD-problem, since you are getting it when installing from the CD not after the installation, when there is a problem with that specific file on your harddisk.
So, apart from the checking of the CD for physical problems (dirt, dust, scratches) the only other solution would be the use of another CD and maybe doing a full disc-copy of that CD onto a CD-R or CD-RW and hoping the best.
As for the Vista procedures the hatter described, all these has to be done before even installing Vista and also on a Windows PC.
The outcome of that would be a modified Vista Installation DVD, which seems to be installing even on iMacs not really supported.
Since I don't have Vista I never tried it myself, though.
But the hatter is 'our local Vista/Windows 7 genius'
As for the 'old XP CD' you found:
such behaviour/error is usually a sign that the XP CD is not at Service Pack level 2 (SP2) which is a must for XP CDs.
However, you can use these instructions http://www.winsupersite.com/showcase/windowsxpsp2slipstream.asp to 'slipstream' yourself a XP SP2 installation CD.
But again, you have to do it on a running Windows PC.
Regards
Stefan

Unknown Hard Error when reformatting. Please help.

Hi, I was going to reformat my HD but got the following error after I inserted the Recovery CD into my CD Rom.
STOP: 0xC0000221 unknown hard error
C:\Winnt\System32\Ntdll.dll
Error 0X 80070456: The media in the drive may have changed PREIN ST6.SWM
Could someone kindly help me please? Is it safe to abort now?
Thanks.

Hi KadeP,
there is indeed not a solution for that CD-problem, since you are getting it when installing from the CD not after the installation, when there is a problem with that specific file on your harddisk.
So, apart from the checking of the CD for physical problems (dirt, dust, scratches) the only other solution would be the use of another CD and maybe doing a full disc-copy of that CD onto a CD-R or CD-RW and hoping the best.
As for the Vista procedures the hatter described, all these has to be done before even installing Vista and also on a Windows PC.
The outcome of that would be a modified Vista Installation DVD, which seems to be installing even on iMacs not really supported.
Since I don't have Vista I never tried it myself, though.
But the hatter is 'our local Vista/Windows 7 genius'
As for the 'old XP CD' you found:
such behaviour/error is usually a sign that the XP CD is not at Service Pack level 2 (SP2) which is a must for XP CDs.
However, you can use these instructions http://www.winsupersite.com/showcase/windowsxpsp2slipstream.asp to 'slipstream' yourself a XP SP2 installation CD.
But again, you have to do it on a running Windows PC.
Regards
Stefan

The upload has failed. An unknown server error occurred during processing. Please try again

I keep getting this message when I try to upload a folio "The upload has failed. An unknown server error occurred during processing. Please try again". It happens every time, some articles do upload but some not.

Thanks Automator21 I manage to upload most of my articles successfully by starting again the whole process. But I have 4 articles that I can't upload, all of this articles have big size videos (one 50mb, other one with 70mb, other with 4 small 30mb videos). I could upload those articles by taking the videos out, but I want those videos on my articles.
I use Adobe Media Encoder to compress the videos and they are not in high quality, for example the 70mb file is an 640x480 8 min. long video. And they are all with H.264 encoding and .mp4.
Do you know how can I fix this problem.
Thanks!

"Unknown Publisher" error message during installation

Ok, I have tried for several days and even got ahold of Microsoft on this issue. Every time i go to download Itunes the download is ok, but when it goes to install Itunes, I ALWAYS get "Unknown Publisher" error message and installation is cancelled. How do i resolve this issue? Any ideas?????

Welcome to AD!
Some folks have had success by downloading and installing QuickTime standalone, then installing itunes after QT. iTunes needs QT codecs to play audio & video.
http://www.apple.com/quicktime/download/
Make sure to get the version withOUT itunes.

Windows error message during palm desktop install

Have been trying unsuccesfully to install palm desktop. Windows XP Home Edition generates error messages after software is installed which prevents using the desktop software. Uncomfortably, I have my data only on my Tungsten e handheld.
Post relates to: Tungsten E

Thanks for the info. I am still unable to install PD414setup.exe onto an XP machine. The error message that I got was: "Error opening installation log file. Verify that the specified log file location exists and is writable".
Thank you in advance,
Chris
Post relates to: Treo 650 (Rogers)

ERROR 3004 during iOS 7 instalation

Hi did someone know why this happend ? I try to upgrade to iOS 7 with new iTunes 11.1. Download was perfect and fast. But during preparing iPhone for upgrate I got error 3004. Since this error I tried all -> delete all iphone, delete all apple products and instal them again, restore phone from deposit and many more... nothing helped. I think problem is not in my phone. I have same error also in one situation when I try restore iPhone from factory restore. I have error 3004 too. But when I restore phone form my restore I dont have this problem. Any help please ?

Here is my solution...I tried for a couple of hours and I stumbled upon this...
- Unplug your ipad and make sure its in recovery mode
- Make sure you have newest iTunes installed
- Goto C:\Windows\System32\drivers\etc
- Make new folder here (name it ipsw) You will also need administrative priviliges
- Move the ipsw files to new folder that you created in the C:\Windows\System32\drivers\etc directory
- Plug your ipad back in recovery mode
- Select your ipsw from the NEW ipsw folder in the C:\Windows\System32\drivers\etc directory by holding the "SHIFT" key when you choose the "RESTORE IPAD"

Error 1335 during Business Objects Install

I have downloaded and unpacked business objects 3.1 however when I run the setup it fails with this error:
Error 1335. The cabinet file 'warfil29.cab' required for this installation is corrupt and cannot be used. This could indicate a network error, an error reading from the CD ROM, or a problem with this package.
I thought maybe my anti-virus was corrupting the cab files when I unpack them but I have stopped my anti-virus, re-unpacked the .rar files and I am still getting the error.
Can anyone help me?

Hello,
also continuing the installation with <Ignore> leads to: "FDI Server Error"
This is not an BO error.
I checked google and others:
This seems to be a hardware / disk error.
I formatted my disk / my partition again and the BO installation works again.
The following does NOT lead to a cure of theses errors:
- reinstall Windows
- recopy the files
- download the BO software a 2 time
- delete directory and recopy BO software
- reinstall BO
- install BO from another disk
- install BO to another directory
- switch of of any AntVirus Software
Best
Martin
Edited by: Martin Sautter on Aug 24, 2009 9:50 AM

Unknown server error (30641)- BB playbook- when trying to create BB ID

unknown server error (30641)- During set up, it asks that you create a Blackberry ID for the BB playbook. Then it shows unknown server error (30641)- I plug it to my computer and download the Desktop manager which ask to update it. I did then it told me disconnect Playbook, install BB ID and plug into PC again. But I got server error again. I am stuck on server error. can you by pass the ID set up and get the BB playbook working and the ID thing after? The ID is not even some critical security feature that must come before the enjoyment of the product. I am really frustrated with my brand new device and my money is wasted. If BB has no fix for this I want my money bacck.
Solved!
Go to Solution.

Perhaps this can help you:
Article ID: KB28198 "Error Id: 30641" is encountered when creating a BlackBerry ID with BlackBerry App World on a smartphone
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

MSI Big Bang-XPower: Errors and Bluescreens Trying to Install Windows 7 64-bit

Hello! This is my first build since... Well, Pentium 3 really. It's been an adventure learning the new hardware. The PC components listed in my signature are the pieces to the machine I'm working on currently, and the one related to this issue.
It boots up just dandy, all the bright and shiny mobo lights blinking reassuringly, recognizes the full 12 GB of RAM in setup, and everything seems peachy until I get to loading the Windows 7 install.
I've tried using an old Vista disc I had lying around, no go. Same issues. I tried loading a different Windows 7 Pro 64-bit disc. Same issues.
These are the error messages I'm receiving most often:
"Windows failed to start. A recent hardware or software change might be the cause. To fix the problem:
1.) Insert your windows installation disc and restart your computer.
2.) Choose your language settings, and then click 'next'.
3.) Click "repair your computer".
If you do not have this disc, contact your system administrator or computer manufacturer for assistance.
File: \windows\system32\ntoskrnl.exe ((This changes every now and then, as does the status number. Always in the system32 file though))
Status: 0xc0000098
Info: Windows failed to load because the kernel is missing, or corrupt."
The error is inconsistent in the files it mentions, also often referring to:
"File: \windows\system32\config\system
Status: 0xc0000001
Info: Windows failed to load because the system registry file is missing, or corrupt."
The HDD is still brand new and entirely blank, not yet even formatted. I have not done much changing things around in the BIOS, because I haven't done much in the BIOS in a very long time, and I'd rather not accidentally make things worse without first obtaining external help. I do not currently intend to overclock the machine, as I am a huge wuss and don't want to screw up my shiny new equipment with my noobsauce. XD
I did some searching around the Interwebs, and found references to similar problems where it was suggested that the person remove all but one stick of RAM and try loading the OS at that point, but it was also mentioned that one stick for that person would be 2 GB. The least I have available to me is 4 GB, and I have attempted this with no change. In this instance, flashing the BIOS to a new version was also recommended. However, I have never flashed a BIOS before and am leaving that as a last resort unless otherwise advised.
Setup currently lists my BIOS Version as V1.2 060910.
It has on a few attempts made it past the 'Starting Windows' screen, and this is the kind of error I generally receive there on a bluescreen:
"STOP: c00002221 Unknown Hard Error
\Systemroot\System32\ntdll.dll"
Over the course of this build, I found that the two previous HDDs that I'd ordered from Newegg were dead and were neither consistently spinning up nor being detected by the mobo, but the current one seems to be recognized just fine. I'd been worried it was a mobo issue, that it just wasn't recognizing them.
I've also read around, and am wondering if perhaps this could be related to a RAM incompatibility issue with the mobo and processor? The RAM that was recommended to me for this build was Triple Channel DDR3 PC 1333, and is supposedly low voltage enough to play happily with the current equipment.
I'd thought to plug the HDD into another machine and format it/install the OS there, then hook it back up and see if it boots, but I have serious doubts as to whether that will ultimately solve the problem, and solving the problem is really what I'm after.
All the equipment save for the power supply and HDD were bought on Newegg.com.
Any assistance would be incredibly appreciated. I'd really like to get the new baby up and running.
:D

Welp, I wasn't a moron bios flasher >.>... It was stable when I flashed it, and it said it was successful... I cleared CMOS after it was done, did the reboot and load optimized thing and reboot again...
Aaaaand it won't go into Windows. Now, I went back at that point and set all the settings back to what let it boot originally: 9-9-9-20, 1.6v, CR of 2... made sure it was booting in the right order, unplugged the USB...
And it freezes midway through the little windows icon forming, bluescreens, and shuts down. I haven't been able to catch what it is yet, since it's crashing so fast.
I tried to run the windows repair thing when the option was given after the crash, and it gets partway through loading the files and then crashes again, sending me right back to the same place.
*facedesk*
On the bright side, what files it does load seem to be loading quickly. _ _;
Edit: Tried booting into my Ubuntu drive, no luck. Just sits stuck at the startup screen. Tried loading Failsafe Defaults... still crashes. Still fiddling with it. I'm hoping the fact that I can get into the BIOS at all means I didn't bust it, but never done this before.
Edit: Managed to load into Startup Repair with just one stick of RAM in it, fiddling with it still and seeing what happens.
Edit: _ _;; Bluescreened and restarted. *facedesk... facedesk...*
Edit: Tried Startup Repair again, and it said 'Startup Repair cannot repair this this computer automatically.' This was the information it gave:
Quote
Problem signature:
Problem Event Name: StartupRepairOffline
Problem Signature 01: 6.1.7600.16385
Problem Signature 02: 6.1.7600.16385
Problem Signature 03: unknown
Problem Signature 04: 21200765
Problem Signature 05: AutoFailover
Problem Signature 06: 2
Problem Signature 07: NoRootCause
OS Version: 6.1.7600.2.0.0.256.1
Locale ID: 1033
The mouse isn't lagging across the screen anymore at least, I guess.
Edit... Again >.>: After some searching around the web, it seems as though there have been other people with similar problems with other boards, etc. Most suggested a repair or reinstall of Windows. I don't have much on the drive installed yet that can't be redone, so I'm going to venture a reinstall. Will post results.

ERROR: stopping on error 7777 during MAIN IMPORT

Dear Expert,
When i am applying Basis and ABAP Support pack 700-17 levels i am getting following red( In Bold) entries in the action log.
   Import phase 'IMPORT_PROPER' (30.12.2008, 14:56:58)
   Error during executing the tp command 'tp IMPORT all CHE ...'
   tp return code: '0014' , tp message: 'A tool used by tp terminated for unknown reasons' , tp output:
     This is tp version 372.04.36 (release 700, unicode enabled)
     ERROR: stopping on error 7777 during MAIN IMPORT
     stopping on error 7777 during MAIN IMPORT
     tp returncode summary:
     TOOLS: Highest return code of single steps was: 14
     WARNS: Highest tp internal warning was: 0118
     standard output from tp and from tools called by tp:
   Details of the error situation can also be found in the import logs
   Interrupt the import due to an error situation (30.12.2008, 15:11:06)
   Display detailed informations concerning the error in phase 'IMPORT_PROPER'
Abort the import due to an error situation (30.12.2008, 15:12:15)
I have found following Notes from the SAP also applied but still i am facing the same error message
Note 1274493 - Windows: TP/R3trans might terminate with old DB library
Note 998004 - Update the Oracle Instant Client on Windows
Regards
Chandra

Hi,
Have you checked note 1288862? Otherwise I recommend to open a message to SAP.
Cheers

I uninstalled Itunes because message "Itunes has stopped working" i attempted to reinstall now get error message "error occurred during installation before itunes could be configured" how to i fix for windows 8.1

I have a PC with windows 8.1. My itunes folder is stored on external drive. I haven't used itunes for a while. I got a message to update to itunes 11.3.1. I got error message that "registry settings used by itunes for importing and burning CD's/DVD's has stopped working" I uninstalled itunes and attempted to reinstall. Now i get message" error occurred during installation before itunes could be configured" How do I fix this.

See Troubleshooting issues with iTunes for Windows updates.
tt2

"iTunes has stopped working" error message during syncing

I've downloaded the latest version of iTunes, and just started to download Podcasts. But now I get the error message during syncing....almost everytime. Is there a solution out there or update that I haven't downloaded??

Same problem here! Moreover, for some reason, the pictures in my iPhone 3GS somehow have been divided into 2 folders, Photos and Medialibrary. And when I open iPhone as a folder through the explorer I can see only the Photos folder, but cannot see the Medialibrary folder which stores the photos taken before updating/upgrading the iPhone and getting separated folders!!! What the hack with all of this?!!! When I connect iPhone to PC it automatically opens iTunes and starts syncronizing it, but at the process of OPTIMIZING the photos (and according to the number of photos it shows, I see that it tries to syncronize that invisible Medialibrary folder) the process suddenly stops and error message pops out Tried the sync test, tried the button DEBUG in that pop out message, but NOTHING HELPS!!! Also, when I open the Medialibrary in my iPhone, the screen get sblack all through scrolling it down, only the video clips are shown there... >.<
So, could you, apple developers, please, explain WHAT THIS PROBLEM IS ABOUT?!!!!!! FIX IT! I am getting ****** of to spend hours at the computer and reading those lame advises which do not help at all! I have my own things to do except reading your support websites. And I payed for the product ready to use, but not a halfproduct which problems should further be solved somehow by users..

Unknown error (-50) during iPhone syncing

I've been consistently getting an error message during WiFi syncing of my iPhone 5 which says, "The iPhone cannot be synced. An unknown error occured (-50)" What should I do to correct this?

error code 50 http://support.apple.com/kb/TS3694#error50 follow instructions to resolve.

Web Application Designer -Unknown Error Occured during Portal Communication

we are getting the below error while using the Web Application Designer .
"Unknown Error Occured during Portal Communication"
Vesrion
SAPBW 700 SP14 on ABAP & SP12 on JAVA.
Found the below error in the default trace
Error 1
Exception thrown Fri Aug 15 11:29:15,070:Exception thrown by application running in JCo Server
java.lang.RuntimeException: Bean RSWR_PREEXECUTION_PROXYnot found on host smy14sap99, ProgId =SMY14SAP99_PORTAL_BD1: Object not found in lookup of RSWR_PREEXECUTION_PROXY.
Error 2
Error> occured >Fri Aug 15 11:29:12,413<
RfcException:
message: 'ashost' is missing
Return code: RFC_INVALID_PARAMETER(19)
error group: 101
key: RFC_ERROR_PROGRAM

Hello,
Have a look at these Notes
SAP Note 988484 RC=12 in after import method for objects BTMP and BITM
SAP Note 916090 RFC-error messages in Web Application Designer 2004s
Thanks
Chandran

975x - "Unknown Hard Error " STOP during RAID XP install

Similar Messages

Maybe you are looking for