990fxa gd80 raid 0 problem please help me i am begging you

so i will start with my set up
990fxa dg80 mb
fx 8350 cpu
780ti
8 gig of ram
256 hdd
2x samsung 850 evo
750 hybrid drive
So at this stage all my data is on the 750 hdd and the disk is stored away. my problem started with me buyng 2 mx100 256 ssds . If my bios is set to ide or ahci they work fine i had my windows instaled on 1 of them all woks fine. Once i switch my bios to raid ( before i set up my raid 0) boot up win 7 instalation i do not see any drives ( i know is normal) load the drivers for the raid controler (sb950 for w7 as it says in themanual) and only my 256 hdd shows up but not the ssds . Than i set them up in ld raid 0 same problem . Tryed on another 2 mbs ... 1 same and a gygabite same problem. So i was sure there is a problem with ssds. I got rid of them got 2 new 850 evo 250 gb same problem. please help me i am so desparate i am willing to pay woth body organs for help

I..have a few questions...
1. You set BIOS to the RAID mode, and under that option there's a Board SATA RAID ROM, do you set it as Legacy ROM?
2. Did you enter Ctrl+F to initialize the drives/Delete Array(If they're used SSDs) and create RAID0?
3. Is your Win7 64 bit or 32 bit?
4. I assume it's 64 bit, did you copy the W764 folder for driver loading?
And make sure you get the driver from here:
http://www.msi.com/support/mb/990FXAGD80.html#down-driver&Win7 64

Similar Messages

System D.O.T automatically why? problem please help me

hello everybody,
please help me my system says at post message that wrong cmos information then gives me option to boot or go to bios when i check my bios , my ONBOARD LAN GETS ENABLED AUTOMATICALLY ,the Frequency tab i check says something like PRIVATE DOT ENABLED AND CPU+AGP SOMETHING i mean my comptuer gets fast and the CPU fan becomes on full speed and i hear loud noise until Corecenter runs it becomes quiet again. the question is is this a bios fault or something , DID ANYBODY WHO BOUGHT 865PE PLATINIUM BOARD EXPERIENCE THIS PROBLEM PLEASE HELP ME MY CONFIGURATIONS ARE BELOW
PENTIUM 2.40 GHZ PRESCOTT (54 C MAXIMUM)
MSI 865PE PLATINIUM BOARD (IT GOT NO RAID ABILITY)
DDR 400 MHZ KINGSTON SINGLE CHIP RAM (ALTHOUGH IT RUNS AT 333MHZ)
MSI GEFORCE FX 5200 T128 (64 BIT DAMN IT!!!)
MSI CD ROM
SONY FLOPPY
COMPUTER CASING WITH SMALL MINI ADDITIONAL FAN ON THE SIDE (IT RUNS MAYBE AND ALSO GIVES ELECTRIC SHOCK OR SOMTHING SOMETIMES)
STABIMATIC 500V AUTOMATIC STABILIZER(ALTHOUGH I HAVE UPS CAN SOME BODY TELL ME IS UPS ALSO STABILIZER OF APC(AMERICAN POWER ----)
AMI BIOS 3.4
SO CAN ANY BODY TELL ME IF THIS IS A PROBLEM OF BIOS SHOULD I UPGRADE TO LATEST
WHAT METHOD THROUGH AUTOUPDATE OR MANUAL , I ONLY ONCE DID MANUALLY ON MY DELL 4100 PIECE OF CAKE !

Hi,
Go to here for MSI LIVEUPDATE
http://www.msi.com.tw/program/support/software/swr/spt_swr_detail.php?UID=556&kind=1
Install and run program.........
BIOS problems:
http://www.msi.com.tw/html/support/bios/note/boot.htm
If you would like to download bios and install........
http://www.msi.com.tw/program/support/bios/bos/spt_bos_detail.php?UID=556&kind=1
You can also choose 3.7 if wish too first.....
I am sure this will help you.
Del

Creative Live Vista IM (VF0420) Problem, PLEASE HELP!

Hi
I use Freetrack to play Airplane Combat Simulators, it's a program that uses the WebCam and a hat with 3 LED to simulate the head movement inside the cockpit.
I'm using Creative Live Vista IM (VF0420) installed the CD drivers and it works perfectly with the Freetrack and all the other programs.
Recently i've bought a Joystick (Saitek Aviator), so I installed the drivers on the CD plugged in the Joystick and it was also working perfectly.
The problem is that now the camera it's not working and the only way to get the camera working is to unplug the Joystick and restart the computer.
After the restart I tested the camera and it was working ok, but again, just after I plug in the Joystick the camera freezes the image and stops working until the next restart with the joystick disconnected.
Resuming, this camera only works when the joystick is disconnected since the computer restart. LOL
I'm using Windows XP 32 Bit + SP2
I tested with other webcam (also Creative) and had no problems working with Freetrack and no conflicts with the Joystick.
I see no conflicts on the Device Manager.
Anyone with the same problem or with the solution please reply.
Thank's in advance.

buddhika wrote:
Im using P4 2.4 ASUS MB (Via chipset VT8237)256MB 60GB HD52x Asus CDromSB Li've 24 bitHard disk is primary IDE, CD rom is secondary IDE masters
I have used old creative and Ectiva sound cards very wel in last years. I gat a SB Li've 24bit new card.
I have a dual boot sys, I installed SB drivers in win98se and it worked well. no problem (although sound card specs didnot said its compatible with win98)
then I installed drivers to winXP sp2, it worked well untill i used cd rom.whenever cd rom is reading data sound gets very distorted (sound is from Hard disk files; mp3 wav, ..). I used different players problem remain,in games the sound distorts when cd runs.cant play a Audio CD, sound is too distorted.
I have changed the Sb's PCI slot and booted first the problem was gone, then restarted and problem remained.
I have questined creative support but no answer.
Please help me !!
If you use cable between CD-ROM dri've and sound card, disable the "Enable Digital Output ...." setting on Device Manager --> DVD/CD-ROM dri'ves --> your dri've name --> Properties --> Properties -tab. If not using cable, then try with cable instead (disable this setting then).
Check if DMA transfer is activated for CD-ROM dri've(s) (try if enabling/disabling it makes any difference).
Disable the Creative CD-ROM detector (service).
jutapa

My iphone is on recovery mode and i can´t turn on it, when i try to recover it from itunes i get: "unknown error (36), i´ve tried to do lot of things but i can´t solve my problem. please help!!

my iphone is on recovery mode and i can´t turn on it, when i try to recover it from itunes i get: unknown error (36), i´ve tried to do lot of things but i can´t solve my problem. please help!!

Hi, i had the same problem. Try to find the file "apple" or "itunes" don't know it anymore exactly. Ahm well you need to delet any information or just plug in your iphone into an other computer. important is that your iphone never has been pluged in this computer before. This was what i did, and it worked!

Problem Please help me.....Let me know the area to look for it I am a DBA..

Problem Please help me.....Let me know the area to look for it I am a DBA..Thanks in advance to let me know the cause and the area to look and fix it...
Server Error in '/' Application.
Problem with SAP/BAPI. SAP.Connector.RfcCommunicationException: Connect to message server failed Connect_PM MSHOST=prddb01.lamrc.com, R3NAME=PRD, GROUP=Prod HR PRD LOCATION CPIC (TCP/IP) on local host ERROR service 'sapmsPRD' unknown TIME Wed May 04 08:59:06 2005 RELEASE 620 COMPONENT NI (network interface) VERSION 36 RC -3 MODULE ninti.c LINE 428 DETAIL NiPServToNo SYSTEM CALL getservbyname COUNTER 1 at SAP.Connector.SAPConnection.ThrowRfcException(RFC_ERROR_INFO_EX rfcerrInfo, Encoding encoding, String languangeCode) at SAP.Connector.SAPConnection.Open() at SAP.Connector.SAPClient.RfcInvoke(String method, Object[] methodParamsIn) at SAP.Connector.SAPClient.SAPInvoke(String method, Object[] methodParamsIn) at SoftwareKeySAPG.SAPProxy1.Z_Bapi_Load_Kpi_Region(ZSOFT_KPI_REGIONS_MTable& Kpi_Regions, ZSOFT_PROD_TYPETable& Prod_Type) at SoftwareKeySAPG.SAPGSK.LoadKPIRegion(DataSet dsProduct)
Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code.
Exception Details: System.Web.Services.Protocols.SoapException: Problem with SAP/BAPI. SAP.Connector.RfcCommunicationException: Connect to message server failed Connect_PM MSHOST=prddb01.lamrc.com, R3NAME=PRD, GROUP=Prod HR PRD LOCATION CPIC (TCP/IP) on local host ERROR service 'sapmsPRD' unknown TIME Wed May 04 08:59:06 2005 RELEASE 620 COMPONENT NI (network interface) VERSION 36 RC -3 MODULE ninti.c LINE 428 DETAIL NiPServToNo SYSTEM CALL getservbyname COUNTER 1 at SAP.Connector.SAPConnection.ThrowRfcException(RFC_ERROR_INFO_EX rfcerrInfo, Encoding encoding, String languangeCode) at SAP.Connector.SAPConnection.Open() at SAP.Connector.SAPClient.RfcInvoke(String method, Object[] methodParamsIn) at SAP.Connector.SAPClient.SAPInvoke(String method, Object[] methodParamsIn) at SoftwareKeySAPG.SAPProxy1.Z_Bapi_Load_Kpi_Region(ZSOFT_KPI_REGIONS_MTable& Kpi_Regions, ZSOFT_PROD_TYPETable& Prod_Type) at SoftwareKeySAPG.SAPGSK.LoadKPIRegion(DataSet dsProduct)
Source Error:
An unhandled exception was generated during the execution of the current web request. Information regarding the origin and location of the exception can be identified using the exception stack trace below.
Stack Trace:
[SoapException: Problem with SAP/BAPI.
SAP.Connector.RfcCommunicationException: Connect to message server failed
Connect_PM MSHOST=prddb01.lamrc.com, R3NAME=PRD, GROUP=Prod HR PRD
LOCATION    CPIC (TCP/IP) on local host
ERROR       service 'sapmsPRD' unknown
TIME        Wed May 04 08:59:06 2005
RELEASE     620
COMPONENT   NI (network interface)
VERSION     36
RC          -3
MODULE      ninti.c
LINE        428
DETAIL      NiPServToNo
SYSTEM CALL getservbyname
COUNTER     1
   at SAP.Connector.SAPConnection.ThrowRfcException(RFC_ERROR_INFO_EX rfcerrInfo, Encoding encoding, String languangeCode)
   at SAP.Connector.SAPConnection.Open()
   at SAP.Connector.SAPClient.RfcInvoke(String method, Object[] methodParamsIn)
   at SAP.Connector.SAPClient.SAPInvoke(String method, Object[] methodParamsIn)
   at SoftwareKeySAPG.SAPProxy1.Z_Bapi_Load_Kpi_Region(ZSOFT_KPI_REGIONS_MTable& Kpi_Regions, ZSOFT_PROD_TYPETable& Prod_Type)
   at SoftwareKeySAPG.SAPGSK.LoadKPIRegion(DataSet dsProduct)]
   System.Web.Services.Protocols.SoapHttpClientProtocol.ReadResponse(SoapClientMessage message, WebResponse response, Stream responseStream, Boolean asyncCall) +1503
   System.Web.Services.Protocols.SoapHttpClientProtocol.Invoke(String methodName, Object[] parameters) +218
   SoftwareKeyUI.InstalledBaseDataWS.InstalledBaseData.LoadKPIRegionMulti(DataSet products)
   SoftwareKeyUI.InstalledBaseDataAccess.LoadKPIRegionMulti(DataSet products)
   SoftwareKeyUI.InstalledBase.GetRegionDetails(Int32 userId, String product, String regionType)
   SoftwareKeyUI.FilteredAccess.GetRegionDetails(Int32 userId, String product, String regionType)
   SoftwareKeyUI.search.LoadRegionDetails()
   SoftwareKeyUI.search.regionType_SelectedIndexChanged(Object sender, EventArgs e)
   System.Web.UI.WebControls.ListControl.OnSelectedIndexChanged(EventArgs e) +108
   System.Web.UI.WebControls.DropDownList.System.Web.UI.IPostBackDataHandler.RaisePostDataChangedEvent() +26
   System.Web.UI.Page.RaiseChangedEvents() +115
   System.Web.UI.Page.ProcessRequestMain() +1099

The error is a very basic one - the sapmsPRD service is not known. You will have to go to <NT_ROOT>\system32\drivers\etc and add the entry sapmsPRD 3600 to this file.
This is basically telling the requester at what port to look for the message server.
C

Problem Please help me.....Let me know the area to look for it

Problem Please help me.....Let me know the area to look for it I am a DBA..Thanks in advance to let me know the cause and the area to look and fix it...
Server Error in '/' Application.
Problem with SAP/BAPI. SAP.Connector.RfcCommunicationException: Connect to message server failed Connect_PM MSHOST=prddb01.lamrc.com, R3NAME=PRD, GROUP=Prod HR PRD LOCATION CPIC (TCP/IP) on local host ERROR service 'sapmsPRD' unknown TIME Wed May 04 08:59:06 2005 RELEASE 620 COMPONENT NI (network interface) VERSION 36 RC -3 MODULE ninti.c LINE 428 DETAIL NiPServToNo SYSTEM CALL getservbyname COUNTER 1 at SAP.Connector.SAPConnection.ThrowRfcException(RFC_ERROR_INFO_EX rfcerrInfo, Encoding encoding, String languangeCode) at SAP.Connector.SAPConnection.Open() at SAP.Connector.SAPClient.RfcInvoke(String method, Object[] methodParamsIn) at SAP.Connector.SAPClient.SAPInvoke(String method, Object[] methodParamsIn) at SoftwareKeySAPG.SAPProxy1.Z_Bapi_Load_Kpi_Region(ZSOFT_KPI_REGIONS_MTable& Kpi_Regions, ZSOFT_PROD_TYPETable& Prod_Type) at SoftwareKeySAPG.SAPGSK.LoadKPIRegion(DataSet dsProduct)
Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code.
Exception Details: System.Web.Services.Protocols.SoapException: Problem with SAP/BAPI. SAP.Connector.RfcCommunicationException: Connect to message server failed Connect_PM MSHOST=prddb01.lamrc.com, R3NAME=PRD, GROUP=Prod HR PRD LOCATION CPIC (TCP/IP) on local host ERROR service 'sapmsPRD' unknown TIME Wed May 04 08:59:06 2005 RELEASE 620 COMPONENT NI (network interface) VERSION 36 RC -3 MODULE ninti.c LINE 428 DETAIL NiPServToNo SYSTEM CALL getservbyname COUNTER 1 at SAP.Connector.SAPConnection.ThrowRfcException(RFC_ERROR_INFO_EX rfcerrInfo, Encoding encoding, String languangeCode) at SAP.Connector.SAPConnection.Open() at SAP.Connector.SAPClient.RfcInvoke(String method, Object[] methodParamsIn) at SAP.Connector.SAPClient.SAPInvoke(String method, Object[] methodParamsIn) at SoftwareKeySAPG.SAPProxy1.Z_Bapi_Load_Kpi_Region(ZSOFT_KPI_REGIONS_MTable& Kpi_Regions, ZSOFT_PROD_TYPETable& Prod_Type) at SoftwareKeySAPG.SAPGSK.LoadKPIRegion(DataSet dsProduct)
Source Error:
An unhandled exception was generated during the execution of the current web request. Information regarding the origin and location of the exception can be identified using the exception stack trace below.
Stack Trace:
[SoapException: Problem with SAP/BAPI.
SAP.Connector.RfcCommunicationException: Connect to message server failed
Connect_PM MSHOST=prddb01.lamrc.com, R3NAME=PRD, GROUP=Prod HR PRD
LOCATION CPIC (TCP/IP) on local host
ERROR service 'sapmsPRD' unknown
TIME Wed May 04 08:59:06 2005
RELEASE 620
COMPONENT NI (network interface)
VERSION 36
RC -3
MODULE ninti.c
LINE 428
DETAIL NiPServToNo
SYSTEM CALL getservbyname
COUNTER 1
at SAP.Connector.SAPConnection.ThrowRfcException(RFC_ERROR_INFO_EX rfcerrInfo, Encoding encoding, String languangeCode)
at SAP.Connector.SAPConnection.Open()
at SAP.Connector.SAPClient.RfcInvoke(String method, Object[] methodParamsIn)
at SAP.Connector.SAPClient.SAPInvoke(String method, Object[] methodParamsIn)
at SoftwareKeySAPG.SAPProxy1.Z_Bapi_Load_Kpi_Region(ZSOFT_KPI_REGIONS_MTable& Kpi_Regions, ZSOFT_PROD_TYPETable& Prod_Type)
at SoftwareKeySAPG.SAPGSK.LoadKPIRegion(DataSet dsProduct)]
System.Web.Services.Protocols.SoapHttpClientProtocol.ReadResponse(SoapClientMessage message, WebResponse response, Stream responseStream, Boolean asyncCall) +1503
System.Web.Services.Protocols.SoapHttpClientProtocol.Invoke(String methodName, Object[] parameters) +218
SoftwareKeyUI.InstalledBaseDataWS.InstalledBaseData.LoadKPIRegionMulti(DataSet products)
SoftwareKeyUI.InstalledBaseDataAccess.LoadKPIRegionMulti(DataSet products)
SoftwareKeyUI.InstalledBase.GetRegionDetails(Int32 userId, String product, String regionType)
SoftwareKeyUI.FilteredAccess.GetRegionDetails(Int32 userId, String product, String regionType)
SoftwareKeyUI.search.LoadRegionDetails()
SoftwareKeyUI.search.regionType_SelectedIndexChanged(Object sender, EventArgs e)
System.Web.UI.WebControls.ListControl.OnSelectedIndexChanged(EventArgs e) +108
System.Web.UI.WebControls.DropDownList.System.Web.UI.IPostBackDataHandler.RaisePostDataChangedEvent() +26
System.Web.UI.Page.RaiseChangedEvents() +115
System.Web.UI.Page.ProcessRequestMain() +1099

Hi
You should make a mapping for the service sapmsPRD in your /etc/services file (On Windows: C:WINDOWSSYSTEM32DRIVERSETCservices). If your instance number is 00 you will have to add the following entry:
sapmsPRD 3600/tcp
Good luck!
René van Es

SB Live 24 + CD rom = Problem, please help

Im using P4 2.4 ASUS MB (Via chipset VT8237)256MB 60GB HD52x Asus CDromSB Li've 24 bitHard disk is primary IDE, CD rom is secondary IDE masters
I have used old creative and Ectiva sound cards very wel in last years. I gat a SB Li've 24bit new card.
I have a dual boot sys, I installed SB drivers in win98se and it worked well. no problem (although sound card specs didnot said its compatible with win98)
then I installed drivers to winXP sp2, it worked well untill i used cd rom.whenever cd rom is reading data sound gets very distorted (sound is from Hard disk files; mp3 wav, ..). I used different players problem remain,in games the sound distorts when cd runs.cant play a Audio CD, sound is too distorted.
I have changed the Sb's PCI slot and booted first the problem was gone, then restarted and problem remained.
I have questined creative support but no answer.
Please help me !!

buddhika wrote:
Im using P4 2.4 ASUS MB (Via chipset VT8237)256MB 60GB HD52x Asus CDromSB Li've 24 bitHard disk is primary IDE, CD rom is secondary IDE masters
I have used old creative and Ectiva sound cards very wel in last years. I gat a SB Li've 24bit new card.
I have a dual boot sys, I installed SB drivers in win98se and it worked well. no problem (although sound card specs didnot said its compatible with win98)
then I installed drivers to winXP sp2, it worked well untill i used cd rom.whenever cd rom is reading data sound gets very distorted (sound is from Hard disk files; mp3 wav, ..). I used different players problem remain,in games the sound distorts when cd runs.cant play a Audio CD, sound is too distorted.
I have changed the Sb's PCI slot and booted first the problem was gone, then restarted and problem remained.
I have questined creative support but no answer.
Please help me !!
If you use cable between CD-ROM dri've and sound card, disable the "Enable Digital Output ...." setting on Device Manager --> DVD/CD-ROM dri'ves --> your dri've name --> Properties --> Properties -tab. If not using cable, then try with cable instead (disable this setting then).
Check if DMA transfer is activated for CD-ROM dri've(s) (try if enabling/disabling it makes any difference).
Disable the Creative CD-ROM detector (service).
jutapa

[TV@Master] Problem please help

I have Msi.mother board PT8-Neo -LSR , Model No.Ms-6799 , main board bios -Phonenix ,maind board version i updat it to 2.2 , cpu size 2.4 G celleron D/256/533 , memory size 256DDram (400),display card Nvidia Riva TNT2 model 64
the problem that i face it when i put my TV@nywhere -master card ,the pc stop at the main page that show the biso version and name of bios company and the letters do not bost well it look like a virus work , and when i take tha card off the pc go normally , i tried put it to other PCI the same problem
please help

i meany by fix the problem of getting the pc go on to windows with card on PCI salot but i still have the broblem of the driver
please read my reply again
my operating system is win me and i have also another pc have XP
when i log in to windows the system show that found my TV@nywhere card but it didnt took the installatin driver for it i tried to install the driver directly
but it give me this 2 mesages when i try to install the driver
MSI TV card is not found ,stop the installation
the other message is
MSI pvs driver installatin failed
i download the driver from msi page also give me the same messages
for known on Device Manager it show me that the driver there but do not have the driver and the ? mark beside them
what to do now

I want to buy an in-app purchase but i don`t remember my security questions and i cant access my recovery email either, what can i do? i have 100$ on my account and cant use it because of that problem, please help URGENT

I want to buy an in-app purchase but i don`t remember my security questions and i cant access my recovery email either, what can i do? i have 100$ on my account and cant use it because of that problem, please help URGENT

If you have a rescue email address on your account then you can use that - follow steps 1 to 5 half-way down this page will give you a reset link on your account : http://support.apple.com/kb/HT5312
If you don't have a rescue email address (you won't be able to add one until you can answer your questions) then you will need to contact Support in your country to get the questions reset : http://support.apple.com/kb/HT5699

I'm in trouble, my iPod Touch is giving 4th shock when recharge and the battery does not last any more. who knows or has a similar problem, please help me. Note: all this after I downloaded the new version OS5.

I'm in trouble, my iPod Touch is giving 4th shock when recharge and the battery does not last any more. who knows or has a similar problem, please help me. Note: all this after I downloaded the new version OS5.

I would make an appointment at the Genius Bar of an Apple store because of the shock issue. I doubt it was caused by the update.

My iphone 4 is acting like crap right i can't even restore it everytime i try to reboot it my iphone freezes at the apple logo it is ******* to the point where i just want to smash it how do i solve this problem please help?

my iphone 4 is acting like crap right i can't even restore it everytime i try to reboot it my iphone freezes at the apple logo it is ******* me off to the point where i just want to smash it how do i solve this problem please help?

Don't worry, just follow these steps to fix iPhone stuck on Apple logo
=> First of all Start your Computer and then connect with Internet connection, now Download the latest version of the iTunes application
=> Now install the iTunes application in your System and connect your Device with computer via Data cable
=> Now connect your Device with iTunes application and then Tab on summary option, see in the left side bar of iTunes
=> Now Select restore option from iTunes and then confirm the Restore Message for better results. After this unplug your Device and Restart it
I hope that will surely
Thank you...

Hello!i have problem to insttal potoshop cs6 this is,we've encountered the following issues.installer failed to initialize.this could be due to a missing file.please download adobe support advisor to detected the problem.please,help me

this is,we've encountered the following issues.
installer failed to initialize.this could be due to a missing file.please download adobe support advisor to detected the problem.
please,help me!

Hi there Mylenium, is there any way you can help me? My cs6 is doing all kinds weird things lately. The liquifying too stopped working completely, when I try to work with the actions, it starts flickering and changing opacity in color by itself. It starts flickering and is completely out of whack! I tried uninstalling and reinstalling and still no luck. I tried getting in touch with adobe and no luck with that neither! Is there anyway you might be able to help?

I have a really really big problem to my iphone icloud please help me i could send you my birth certificate for confirmation that im the real user please help me

i have a really really big problem to my iphone icloud please help me i could send you my birth certificate for confirmation that im the real user please help me apple.corp and please tell me if this is not possible to be done it almost a month that i cant use my iphone.
thank you for those who read this
<Email Edited by Host>

Remove your email address. This is a public website, and you are addressing thousands of strangers.
After doing that, tell us what your issue actually is. This is a user-to-user technical forum. You are not addressing Apple here.

My iPad stop working suddenly i see black screen only pressing the home? and sleep button dose not solve the problem please help?

My iPad stop working suddenly i see black screen only pressing the home and sleep button dose not solve the problem please help ?

Frozen or unresponsive iPad
Resolve these most common issues:
    •    Display remains black or blank
    •    Touch screen not responding
    •    Application unexpectedly closes or freezes
http://www.apple.com/support/ipad/assistant/ipad/
iPad Frozen, not responding, how to fix
http://appletoolbox.com/2012/07/ipad-frozen-not-responding-how-to-fix/
iPad Frozen? How to Force Quit an App, Reset or Restart Your iPad
http://ipadacademy.com/2010/11/ipad-frozen-how-to-force-quit-an-app-reset-or-res tart-your-ipad
Black or Blank Screen on iPad or iPhone
http://appletoolbox.com/2012/10/black-or-blank-screen-on-ipad-or-iphone/
What to Do When Your iPad Won't Turn On
http://ipad.about.com/od/iPad_Troubleshooting/ss/What-To-Do-When-Your-Ipad-Wo-No t-Turn-On.htm
iOS: Not responding or does not turn on
http://support.apple.com/kb/TS3281
Home button not working or unresponsive, fix
http://appletoolbox.com/2013/04/home-button-not-working-or-unresponsive-fix/
Fixing an iPad Home Button
http://tinyurl.com/om6rd6u
iPad: Basic troubleshooting
http://support.apple.com/kb/TS3274
 Cheers, Tom

I am using firefox 3.6.17 i upgraded it to 4.1.but it does not work properly sometimes it opens every website and most of the time it does not work . so what is the problem please help . thank you

i am using firefox 3.6.17 i upgraded it to 4.1.but it does not work properly sometimes it opens every website and most of the time it does not work . so what is the problem please help . thank you

Did you check your security software (firewall)?
A possible cause is security software (firewall) that blocks or restricts Firefox or the plugin-container process without informing you, possibly after detecting changes (update) to the Firefox program.
Remove all rules for Firefox from the permissions list in the firewall and let your firewall ask again for permission to get full unrestricted access to internet for Firefox and the plugin-container process.
See:
* [[Server not found]]
* [[Firewalls]]

990fxa gd80 raid 0 problem please help me i am begging you

Similar Messages

Maybe you are looking for