9971 SIP Phones at remote location status REJECTED

Hi,
I have 10 locations, Site 1, 2, ....10. All these locations have 10 phones each. These phone are configured with default SIP Profile. Were registered and working fine. While adding a subscriber I downgraded the cluster. After bringing back to regular version. I find all my phones status shows unknown. 
I tried to change dhcp option 150 on dhcp router to point different server and reconfigured with the correct tftp ip address. Also I tried to shutdown the interface where phones are connected and bring it back up. Restarted tftp server many times. Even after all these I find my phones in REJECTED state. 
I know personal reset on each phone will fix this issue. But is there any other way to fix this, since these phones are at remote locations.
Any help is appreciated.
Thanks,
MR

Hello!
I think, that the most possible issue is problem with CTL/ITL.
Certificates were regenerated while downgrading/upgrading and were not propagated to the phones.
So u should try to delete ITL on the phones.
Regards,
Kirill

Similar Messages

  • Cisco UC5xx 8.6 Support for 99xx SIP phones using CCA 3.2.1

    Hi Friends,
    I was looking through posts here in the SMB commuity, the SWP 8.6 for UC5xx, the RN for CCA 3.2.1, and the OLH for CCA 3.2.1, and found a nice thread that will help anyone wanting to get a 9951 or 9971 SIP phone to operate on the UC5xx after upgrade to the Cisco IOS {15.1(4)M4} bringing CME 8.6 to Telephony Services and selection of the SIP 9-2-2 phone loads (included in the SWP) for 99xx.
    My only inquiry for Cisco to check, would be why isnt this documented in the release notes,
    https://supportforums.cisco.com/servlet/JiveServlet/previewBody/26979-102-1-67567/cca_3_2_2_relnotes.pdf
    since CCA doesnt seem to add the 'load 99xx sip99xx.9-2-2' statement, the 'tftp-path flash:', followed by the 'create profile' under VOICE REGISTER GLOBAL?
    If it is supposed to work, then I would alert you that it did not.  After Upgrading CCA to 3.2.1 and then upgrading the UC5xx to SWP 8.6, the adminisrtrator manually adds the 99xx phone by entering MAC and Type under Configure> Telephony> Users/Extensions> Users and Phones: ADD button.  Nothing special, just a normal extension on one button, Video Enabled, and a VM box created.  This allows the phone to register just fine, but it doesnt automatically upgrade to 9-2-2 due to the missing bold commands above.
    I think if this were a known defect, it would have been documented in the RNs, so I raise it to your attention.
    Which operation should have added these commands?
    Can you let us know if this is an anomaly or if everyone will encounter this?
    Thanks kindly,
    Steve

    Yeah uh beleive me Steven, I have tried everything and every location to get these phones working and nothing did. Other people have the same issue (thread here somewhere) luckily mine are only out 1 hour others are out many hours.
    Thanks,
    Bob James

  • Cisco SIP Phone 9971 won't register on CME 8.6 or 8.5 Please HELP

    Please help me , I have problem with registering Cisco SIP phone 9971 with CME 8.6 on ISR 2901.
    I configured CME for SIP clients, then I add configuration for 9971 phone and create profiles.  Phone downloaded SEP...xml file from CME,after that phone look for g4-tones.xml and gd-sip.jar files, I added them to CME after that phone downloaded them and reboot. Now phone is stuck in some kind of loop and does not register on CME.
    On phone log I can see repeting next few messeges.
    12:01:58a No DNS Server IP
    12:01:59a Updating Trust list
    12:01:59a No Trust List instaled
    12:01:59a SEP04C5AB03B0D.cnf.xml (TFTP)  // at this time phone download SEP...xml file from CME
    12:02:00a VPN Error: VPN is not Configured
    on CME if issue DEBUG TFTP EVENTS i receive next few lines
    *Aug 18 18:20:19.891: TFTP: Looking for CTLSEP04C5A4B03B0D.tlv
    *Aug 18 18:20:19.987: TFTP: Looking for ITLSEP04C5A4B03B0D.tlv
    *Aug 18 18:20:20.083: TFTP: Looking for ITLFile.tlv
    *Aug 18 18:20:20.347: TFTP: Looking for SEP04C5A4B03B0D.cnf.xml
    *Aug 18 18:20:20.351: TFTP: Opened flash:/SEP04C5A4B03B0D.cnf.xml, fd 14, size 4585 for process 141
    *Aug 18 18:20:20.363: TFTP: Finished flash:/SEP04C5A4B03B0D.cnf.xml, time 00:00:00 for process 141
    here you can see verison info of CME
    Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.1(4)M, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2011 by Cisco Systems, Inc.
    Compiled Thu 24-Mar-11 15:31 by prod_rel_team
    ROM: System Bootstrap, Version 15.0(1r)M9, RELEASE SOFTWARE (fc1)
    ELTOSAN_ROUTER uptime is 1 hour, 50 minutes
    System returned to ROM by reload at 16:29:20 UTC Thu Aug 18 2011
    System image file is "flash:/c2900-universalk9-mz.SPA.151-4.M.bin"
    Last reload type: Normal Reload
    Last reload reason: Reload Command
    Cisco CISCO2901/K9 (revision 1.0) with 471040K/53248K bytes of memory.
    Processor board ID FGL1508252Y
    3 Gigabit Ethernet interfaces
    2 terminal lines
    1 Virtual Private Network (VPN) Module
    4 Voice FXO interfaces
    4 Voice FXS interfaces
    1 Internal Services Module (ISM) with Services Ready Engine (SRE)
       Survivable Remote Site Voicemail (SRSV) on Cisco Unity Express (CUE) 8.5.1 in slot/sub-slot 0/0
    DRAM configuration is 64 bits wide with parity enabled.
    255K bytes of non-volatile configuration memory.
    254464K bytes of ATA System CompactFlash 0 (Read/Write)
    License Info:
    License UDI:
    Device#   PID                   SN
    *0        CISCO2901/K9          xxxxxxxxxxxxx
    Technology Package License Information for Module:'c2900'
    Technology    Technology-package          Technology-package
                  Current       Type          Next reboot
    ipbase        ipbasek9      Permanent     ipbasek9
    security      securityk9    Permanent     securityk9
    uc            uck9          Permanent     uck9
    data          None          None          None
    Configuration register is 0x2102
    this is RUNNING CONFIGURATION
    ! Last configuration change at 16:10:12 UTC Thu Aug 18 2011
    version 15.1
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    hostname ELTOSAN_ROUTER
    boot-start-marker
    boot system flash:/c2900-universalk9-mz.SPA.151-4.M.bin
    boot-end-marker
    no aaa new-model
    no ipv6 cef
    ip source-route
    no ip routing
    no ip cef
    no ip dhcp use vrf connected
    ip dhcp excluded-address 192.168.5.1 192.168.5.10
    ip dhcp excluded-address 192.168.5.200 192.168.5.255
    ip dhcp pool phone
       network 192.168.5.0 255.255.255.0
       default-router 192.168.5.251
       option 150 ip 192.168.5.251
    ip dhcp pool data
       relay source 192.168.2.0 255.255.255.0
       relay destination 192.168.2.201
    multilink bundle-name authenticated
    crypto pki token default removal timeout 0
    voice-card 0
    voice service voip
    allow-connections h323 to h323
    allow-connections h323 to sip
    allow-connections sip to h323
    allow-connections sip to sip
    supplementary-service h450.12
    fax protocol pass-through g711alaw
    sip
      registrar server expires max 3600 min 120
    voice register global
    mode cme
    source-address 192.168.5.251 port 5060
    max-dn 6
    max-pool 6
    load 9971 sip9971.9-1-1SR1.loads
    authenticate register
    tftp-path flash:
    create profile sync 0005135312289902
    voice register dn  1
    number 207
    allow watch
    name GossaVM
    label 207
    voice register dn  3
    number 101
    name Dejan
    label 101
    mwi
    voice register pool  1
    id mac 000C.29C5.0011
    number 1 dn 1
    dtmf-relay sip-notify
    username testvm password testera
    codec g711alaw
    voice register pool  3
    id mac 04C5.A4B0.3B0D
    type 9971
    number 3 dn 3
    presence call-list
    dtmf-relay rtp-nte
    username dejan password 1234
    codec g711alaw
    no vad
    license udi pid CISCO2901/K9 sn xxxxxxxxxxxx
    hw-module ism 0
    hw-module pvdm 0/0
    redundancy
    interface GigabitEthernet0/0
    description INTERFACE INTERNAL
    no ip address
    no ip route-cache
    duplex auto
    speed auto
    no mop enabled
    interface GigabitEthernet0/0.2
    description LAN DATA
    encapsulation dot1Q 2
    ip address 192.168.2.251 255.255.255.0
    no ip route-cache
    interface GigabitEthernet0/0.5
    description LAN VOICE
    encapsulation dot1Q 5
    ip address 192.168.5.251 255.255.255.0
    no ip route-cache
    interface ISM0/0
    no ip address
    no ip route-cache
    shutdown
    !Application: SRSV-CUE Running on ISM
    interface GigabitEthernet0/1
    no ip address
    no ip route-cache
    shutdown
    duplex auto
    speed auto
    interface ISM0/1
    description Internal switch interface connected to Internal Service Module
    shutdown
    interface Vlan1
    no ip address
    no ip route-cache
    shutdown
    ip forward-protocol nd
    no ip http server
    no ip http secure-server
    snmp-server community public RO
    tftp-server flash:dkern9971.100609R2-9-1-1SR1.sebn alias dkern9971.100609R2-9-1-1SR1.sebn
    tftp-server flash:kern9971.9-1-1SR1.sebn alias kern9971.9-1-1SR1.sebn
    tftp-server flash:rootfs9971.9-1-1SR1.sebn alias rootfs9971.9-1-1SR1.sebn
    tftp-server flash:sboot9971.031610R1-9-1-1SR1.sebn alias sboot9971.031610R1-9-1-1SR1.sebn
    tftp-server flash:skern9971.022809R2-9-1-1SR1.sebn alias skern9971.022809R2-9-1-1SR1.sebn
    tftp-server flash:sip9971.9-1-1SR1.loads alias sip9971.9-1-1SR1.loads
    tftp-server flash:United_States/g4-tones.xml
    tftp-server flash:English_United_States/gd-sip.jar
    control-plane
    voice-port 0/0/0
    voice-port 0/0/1
    voice-port 0/0/2
    voice-port 0/0/3
    voice-port 0/1/0
    voice-port 0/1/1
    voice-port 0/1/2
    voice-port 0/1/3
    mgcp profile default
    gatekeeper
    shutdown
    line con 0
    line aux 0
    line 67
    no activation-character
    no exec
    transport preferred none
    transport input all
    transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
    stopbits 1
    line vty 0 4
    password jebiga
    login
    transport input all
    end
    I did not have any kind of problem with X-LITE to register to CME. also try with few SCCP phones 7940  and I did not any kind of problem .
    this is content of SEP....xml file for 9971
    <device>
    <deviceProtocol>SIP</deviceProtocol>
    <devicePool>
    <dateTimeSetting>
    <dateTemplate>M/D/YA</dateTemplate>
    <timeZone>Pacific Standard/Daylight Time</timeZone>
    <ntps>
    <ntp priority="0">
    <name>0.0.0.0</name>
    <ntpMode>unicast</ntpMode>
    </ntp>
    </ntps>
    </dateTimeSetting>
    <callManagerGroup>
    <members>
    <member priority="0">
    <callManager>
    <ports>
    <sipPort>5060</sipPort>
    </ports>
    <processNodeName>192.168.5.251</processNodeName>
    </callManager>
    </member>
    </members>
    </callManagerGroup>
    </devicePool>
    <sipProfile>
    <sipProxies>
    <registerWithProxy>true</registerWithProxy>
    </sipProxies>
    <sipCallFeatures>
    <cnfJoinEnabled>true</cnfJoinEnabled>
    <localCfwdEnable>true</localCfwdEnable>
    <callForwardURI>service-uri-cfwdall</callForwardURI>
    <callPickupURI>service-uri-pickup</callPickupURI>
    <callPickupGroupURI>service-uri-gpickup</callPickupGroupURI>
    <callHoldRingback>2</callHoldRingback>
    <semiAttendedTransfer>true</semiAttendedTransfer>
    <anonymousCallBlock>2</anonymousCallBlock>
    <callerIdBlocking>2</callerIdBlocking>
    <dndControl>2</dndControl>
    <remoteCcEnable>true</remoteCcEnable>
    </sipCallFeatures>
    <sipStack>
    <remotePartyID>true</remotePartyID>
    </sipStack>
    <sipLines>
    <line button="1" lineIndex="1">
    <featureID>9</featureID>
    <featureLabel></featureLabel>
    <proxy>USECALLMANAGER</proxy>
    <port>5060</port>
    <name></name>
    <displayName></displayName>
    <autoAnswer>
    <autoAnswerEnabled>2</autoAnswerEnabled>
    </autoAnswer>
    <callWaiting>1</callWaiting>
    <authName>dejan</authName>
    <authPassword>1234</authPassword>
    <sharedLine>false</sharedLine>
    <messagesNumber></messagesNumber>
    <ringSettingActive>5</ringSettingActive>
    <forwardCallInfoDisplay>
    <callerName>true</callerName>
    <callerNumber>true</callerNumber>
    <redirectedNumber>true</redirectedNumber>
    <dialedNumber>true</dialedNumber>
    </forwardCallInfoDisplay>
    </line>
    <line button="2" lineIndex="2">
    <featureID>9</featureID>
    <featureLabel>101</featureLabel>
    <proxy>USECALLMANAGER</proxy>
    <port>5060</port>
    <name>101</name>
    <displayName>Dejan Rakic</displayName>
    <autoAnswer>
    <autoAnswerEnabled>2</autoAnswerEnabled>
    </autoAnswer>
    <callWaiting>1</callWaiting>
    <authName>dejan</authName>
    <authPassword>1234</authPassword>
    <sharedLine>false</sharedLine>
    <messagesNumber></messagesNumber>
    <ringSettingActive>5</ringSettingActive>
    <forwardCallInfoDisplay>
    <callerName>true</callerName>
    <callerNumber>true</callerNumber>
    <redirectedNumber>true</redirectedNumber>
    <dialedNumber>true</dialedNumber>
    </forwardCallInfoDisplay>
    </line>
    </sipLines>
    <enableVad>true</enableVad>
    <preferredCodec>g711alaw</preferredCodec>
    <dialTemplate></dialTemplate>
    <kpml>1</kpml>
    <phoneLabel></phoneLabel>
    <stutterMsgWaiting>2</stutterMsgWaiting>
    <disableLocalSpeedDialConfig>true</disableLocalSpeedDialConfig>
    <dscpForAudio>184</dscpForAudio>
    <dscpVideo>136</dscpVideo>
    </sipProfile>
    <commonProfile>
    <phonePassword>1234</phonePassword>
    <callLogBlfEnabled>2</callLogBlfEnabled>
    </commonProfile>
    <featurePolicyFile>featurePolicyDefault.xml</featurePolicyFile>
    <loadInformation>sip9971.9-1-1SR1.loads</loadInformation>
    <vendorConfig>
    </vendorConfig>
    <commonConfig>
    <videoCapability>0</videoCapability>
    <ciscoCamera>0</ciscoCamera>
    </commonConfig>
    <sshUserId>dejan</sshUserId>
    <sshPassword>1234</sshPassword>
    <userId></userId>
    <phoneServices>
    <provisioning>2</provisioning>
    <phoneService  type="1" category="0">
    <name>Missed Calls</name>
    <phoneLabel></phoneLabel>
    <url>Application:Cisco/MissedCalls</url>
    <vendor></vendor>
    <version></version>
    </phoneService>
    <phoneService  type="1" category="0">
    <name>Received Calls</name>
    <phoneLabel></phoneLabel>
    <url>Application:Cisco/ReceivedCalls</url>
    <vendor></vendor>
    <version></version>
    </phoneService>
    <phoneService  type="1" category="0">
    <name>Placed Calls</name>
    <phoneLabel></phoneLabel>
    <url>Application:Cisco/PlacedCalls</url>
    <vendor></vendor>
    <version></version>
    </phoneService>
    <phoneService  type="2" category="0">
    <name>Voicemail</name>
    <phoneLabel></phoneLabel>
    <url>Application:Cisco/Voicemail</url>
    <vendor></vendor>
    <version></version>
    </phoneService>
    </phoneServices>
    <versionStamp>0131511014412102</versionStamp>
    <userLocale>
    <name>English_United_States</name>
    <langCode>en</langCode>
    </userLocale>
    <networkLocale>United_States</networkLocale>
    <networkLocaleInfo>
    <name>United_States</name>
    </networkLocaleInfo>
    <authenticationURL></authenticationURL>
    <directoryURL></directoryURL>
    <servicesURL>http://192.168.5.251:80/CMEserverForPhone/serviceurl</servicesURL>
    <dscpForSCCPPhoneServices>0</dscpForSCCPPhoneServices>
    <dscpForCm2Dvce>96</dscpForCm2Dvce>
    <transportLayerProtocol>2</transportLayerProtocol>
    </device>

    Hello,
    I'm facing exactly the same problem, that is:
    a Cisco SIP Phone 9971 won't register on CME 8.6 running on a 2811
    I have read all the postings to this Forum, but I have not been able to solve it.
    In my case the commands voice register dn  and  voice register pool are OK.
    So frankly, I have no idea what I could be missing.
    I'm pasting the Router's config.
    I hope somebody is able to point me in the right direction.
    Here is the config.  Thank you!
    C2811#sh run
    Building configuration...
    version 15.1
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    hostname C2811
    no aaa new-model
    dot11 syslog
    ip source-route
    ip cef
    ip dhcp excluded-address 172.25.140.1 172.25.140.10
    ip dhcp excluded-address 172.35.140.1 172.35.140.10
    ip dhcp pool Data
    network 172.25.140.0 255.255.255.0
    default-router 172.25.140.1
    option 150 ip 172.25.140.1
    dns-server 172.25.140.1
    ip dhcp pool Voice
    network 172.35.140.0 255.255.255.0
    default-router 172.35.140.1
    option 150 ip 172.35.140.1
    dns-server 172.35.140.1
    no ip domain lookup
    no ipv6 cef
    multilink bundle-name authenticated
    voice service voip
    allow-connections sip to sip
    sip
      registrar server expires max 3600 min 120
    voice register global
    mode cme
    source-address 172.25.140.1 port 5060
    max-dn 40
    max-pool 42
    load 9971 sip9971.9-4-1-9.loads
    authenticate register
    authenticate realm cisco
    tftp-path flash:
    create profile sync 0004820400584603
    voice register dn  1
    number 1010
    allow watch
    name Phone10
    label Phone10
    mwi
    voice register pool  1
    id mac 189C.5DB6.BD09
    type 9971
    number 1 dn 1
    presence call-list
    dtmf-relay rtp-nte
    username adm password adm
    call-forward b2bua busy 68600
    codec g711ulaw
    no vad
    camera
    video
    voice-card 0
    crypto pki token default removal timeout 0
    crypto pki trustpoint TP-self-signed-1879153754
    enrollment selfsigned
    subject-name cn=IOS-Self-Signed-Certificate-1879153754
    revocation-check none
    rsakeypair TP-self-signed-1879153754
    crypto pki certificate chain TP-self-signed-1879153754
    certificate self-signed 01
    (details ommited)
    license udi pid CISCO2811 sn FTX1146A44H
    username admin privilege 15 password 0 admin
    redundancy
    interface FastEthernet0/0
    no ip address
    duplex auto
    speed auto
    interface FastEthernet0/0.25
    description Data VLAN
    encapsulation dot1Q 25
    ip address 172.25.140.1 255.255.255.0
    interface FastEthernet0/0.35
    description Voice VLAN
    encapsulation dot1Q 35
    ip address 172.35.140.1 255.255.255.0
    interface FastEthernet0/1
    no ip address
    shutdown
    duplex auto
    speed auto
    ip forward-protocol nd
    ip http server
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 600 life 86400 requests 10000
    tftp-server flash:P00308010200.bin
    tftp-server flash:P00308010200.sbn
    tftp-server flash:P00308010200.sb2
    tftp-server flash:P00308010200.loads
    tftp-server flash:SCCP42.9-3-1SR3-1S.loads
    tftp-server flash:apps42.9-3-1ES19.sbn
    tftp-server flash:cnu42.9-3-1ES19.sbn
    tftp-server flash:cvm42sccp.9-3-1ES19.sbn
    tftp-server flash:dsp42.9-3-1ES19.sbn
    tftp-server flash:jar42sccp.9-3-1ES19.sbn
    tftp-server flash:term42.default.loads
    tftp-server flash:term62.default.loads
    tftp-server flash:SCCP45.9-3-1SR3-1S.loads
    tftp-server flash:apps45.9-3-1ES19.sbn
    tftp-server flash:cnu45.9-3-1ES19.sbn
    tftp-server flash:cvm45sccp.9-3-1ES19.sbn
    tftp-server flash:dsp45.9-3-1ES19.sbn
    tftp-server flash:jar45sccp.9-3-1ES19.sbn
    tftp-server flash:term45.default.loads
    tftp-server flash:term65.default.loads
    tftp-server flash:/Ringtones/Ringlist.xml alias Ringlist.xml
    tftp-server flash:/Ringtones/DistinctiveRingList.xml alias DistinctiveRingList.x
    ml
    tftp-server flash:sip9971.9-4-1-9.loads
    tftp-server flash:kern9971.9-4-1-9.sebn
    tftp-server flash:rootfs9971.9-4-1-9.sebn
    tftp-server flash:dkern9971.100609R2-9-4-1-9.sebn
    tftp-server flash:sboot9971.031610R1-9-4-1-9.sebn
    tftp-server flash:skern9971.022809R2-9-4-1-9.sebn
    tftp-server flash:/g4-tones.xml alias United_States/g4-tones.xml
    tftp-server flash:/gd-sip.jar alias English_United_States/gd-sip.jar
    control-plane
    mgcp profile default
    telephony-service
    max-ephones 24
    max-dn 48
    ip source-address 172.25.140.1 port 2000
    cnf-file location flash:
    load 7960-7940 P00308010200
    load 7942 SCCP42.9-3-1SR3-1S.loads
    load 7945 SCCP45.9-3-1SR3-1S.loads
    load 7962 SCCP42.9-3-1SR3-1S.loads
    load 7965 SCCP45.9-3-1SR3-1S.loads
    max-conferences 8 gain -6
    dn-webedit
    transfer-system full-consult
    create cnf-files version-stamp 7960 Feb 11 2014 07:18:32
    ephone-dn  1
    number 1001
    description Phone 1
    name Phone 1
    hold-alert 30 originator
    ephone-dn  2
    number 1002
    description Phone 2
    name Phone 2
    hold-alert 30 originator
    ephone-dn  3
    number 1003
    description Phone 3
    name Phone 3
    hold-alert 30 originator
    ephone  1
    device-security-mode none
    mac-address 001C.58FB.6E0F
    button  1:1
    ephone  2
    device-security-mode none
    mac-address 0014.A981.7F8A
    button  1:2
    ephone  3
    device-security-mode none
    mac-address 0006.5356.A4B8
    button  1:3
    alias exec con conf t
    alias exec sib show ip int brief
    alias exec srb show run | b
    alias exec sri show run int
    line con 0
    exec-timeout 0 0
    logging synchronous
    line aux 0
    line vty 0 4
    privilege level 15
    login local
    transport input telnet ssh
    transport output telnet ssh
    line vty 5 15
    privilege level 15
    login local
    transport input telnet ssh
    transport output telnet ssh
    scheduler allocate 20000 1000
    ntp master 1
    end
    C2811#

  • Cisco SIP Phone 9971 will not register on CME 8.6

    Hello,
    I'm trying to configure a  Cisco SIP Phone 9971,
    but it won't register on CME 8.6, which is running on a 2811
    The Phone shows this error message: Phone Not Registered.
    And when I check the the Status Messages in the Phone, I see the following:
    VPN Error: vpn is not configured
    Actually, it shows all these 4 messages in a constant Loop:
    12:01:59a SEP189C5DB6BD09.cnf.xml (TFTP)
    12:01:59a No Trust List instaled
    12:01:59a Updating Trust list
    12:02:00a VPN Error: VPN is not Configured
    It seems that this VPN Error is keeping the Phone from registering.
    This is repeated for ever and the Phone never registers; at least that's what it appears.
    However, when I do a sh voice register pool, I get the following:
    C2811#sh voice register pool  1
    Pool Tag 1
    Config:
      Mac address is 189C.5DB6.BD09
      Type is 9971
      Number list 1 : DN 1
      Proxy Ip address is 0.0.0.0
      Current Phone load version is Cisco-CP9971/9.4.1
      DTMF Relay is enabled, rtp-nte
      Call Waiting is enabled
      DnD is disabled
      Video is enabled
      Camera is enabled
      Busy trigger per button value is 0
      call-forward b2bua busy 68600
      keep-conference is enabled
      registration expires timer max is 3600 and min is 120
      username adm password adm
      kpml signal is enabled
      Lpcor Type is none
      blf call list is enabled
      Transport type is udp
      service-control mechanism is supported
      registration Call ID is [email protected]
      Registration method: per line
      Privacy feature is not configured.
      Privacy button is disabled
      active primary line is: 1010
      contact IP address: 172.35.140.12 port 5060
      Phone SIS Version:  6.0.2
      GW SIS Version:  1.0.0
    Dialpeers created:
    Dial-peers for Pool 1:
    dial-peer voice 40001 voip
    destination-pattern 1010
    session target ipv4:172.35.140.12:5060
    session protocol sipv2
    dtmf-relay rtp-nte
    digit collect kpml
    codec  g711ulaw bytes 160
    no vad
      call-fwd-busy        68600
      after-hours-exempt   FALSE
    Statistics:
      Active registrations  : 4
      Total SIP phones registered: 1
      Total Registration Statistics
        Registration requests  : 4
        Registration success   : 4
        Registration failed    : 0
        unRegister requests    : 0
        unRegister success     : 0
        unRegister failed      : 0
        Attempts to register
               after last unregister : 0
        Last register request time   : 18:11:43.551 UTC Mon Feb 24 2014
        Last unregister request time :
        Register success time        : 18:11:43.551 UTC Mon Feb 24 2014
        Unregister success time      :
    C2811#
    This sh voice register pool  seems to indicate that the Phone has actually registered.
    But I still get the  Phone Not Registered   message on the screen!
    I did some Debugs and they also seem to indicate that the Phone has indeed registered:
    Feb 24 18:01:12.399: VOICE_REG_POOL: Creating param container for dial-peer 4000
    1.VOICE_REG_POOL pool->tag(1), dn->tag(1), submask(1)
    VOICE_REG_POOL pool_tag(1), dn_tag(1)
    Feb 24 18:01:12.399: VOICE_REG_POOL: Created dial-peer entry of type 0
    Feb 24 18:01:12.399: VOICE_REG_POOL: Registration successful for 1010, registration id is 1
    Feb 24 18:01:12.411: VOICE_REG_POOL: Contact matches pool 1 number list 1
    Feb 24 18:01:12.411: VOICE_REG_POOL: GW SIS: X-cisco-cme-sis-1.0.0
    Feb 24 18:01:12.411: VOICE REGISTER POOL-1 has registered.
                                   Name:SEP189C5DB6BD09 IP:172.35.140.12  DeviceType:Phone
    So frankly, I have no idea why the Phone keeps showing the Phone Not Registered message.
    I'm pasting the Router's config.
    I hope somebody is able to point me in the right direction.
    Here is the config.  Thank you!
    C2811#sh run
    Building configuration...
    version 15.1
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    hostname C2811
    no aaa new-model
    dot11 syslog
    ip source-route
    ip cef
    ip dhcp excluded-address 172.25.140.1 172.25.140.10
    ip dhcp excluded-address 172.35.140.1 172.35.140.10
    ip dhcp pool Data
    network 172.25.140.0 255.255.255.0
    default-router 172.25.140.1
    option 150 ip 172.25.140.1
    dns-server 172.25.140.1
    ip dhcp pool Voice
    network 172.35.140.0 255.255.255.0
    default-router 172.35.140.1
    option 150 ip 172.35.140.1
    dns-server 172.35.140.1
    no ip domain lookup
    no ipv6 cef
    multilink bundle-name authenticated
    voice service voip
    allow-connections sip to sip
    sip
      registrar server expires max 3600 min 120
    voice register global
    mode cme
    source-address 172.25.140.1 port 5060
    max-dn 40
    max-pool 42
    load 9971 sip9971.9-4-1-9.loads
    authenticate register
    authenticate realm cisco
    tftp-path flash:
    create profile sync 0004820400584603
    voice register dn  1
    number 1010
    allow watch
    name Phone10
    label Phone10
    mwi
    voice register pool  1
    id mac 189C.5DB6.BD09
    type 9971
    number 1 dn 1
    presence call-list
    dtmf-relay rtp-nte
    username adm password adm
    call-forward b2bua busy 68600
    codec g711ulaw
    no vad
    camera
    video
    voice-card 0
    crypto pki token default removal timeout 0
    crypto pki trustpoint TP-self-signed-1879153754
    enrollment selfsigned
    subject-name cn=IOS-Self-Signed-Certificate-1879153754
    revocation-check none
    rsakeypair TP-self-signed-1879153754
    crypto pki certificate chain TP-self-signed-1879153754
    certificate self-signed 01
    (details ommited)
    license udi pid CISCO2811 sn FTX1146A44H
    username admin privilege 15 password 0 admin
    redundancy
    interface FastEthernet0/0
    no ip address
    duplex auto
    speed auto
    interface FastEthernet0/0.25
    description Data VLAN
    encapsulation dot1Q 25
    ip address 172.25.140.1 255.255.255.0
    interface FastEthernet0/0.35
    description Voice VLAN
    encapsulation dot1Q 35
    ip address 172.35.140.1 255.255.255.0
    interface FastEthernet0/1
    no ip address
    shutdown
    duplex auto
    speed auto
    ip forward-protocol nd
    ip http server
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 600 life 86400 requests 10000
    tftp-server flash:P00308010200.bin
    tftp-server flash:P00308010200.sbn
    tftp-server flash:P00308010200.sb2
    tftp-server flash:P00308010200.loads
    tftp-server flash:SCCP42.9-3-1SR3-1S.loads
    tftp-server flash:apps42.9-3-1ES19.sbn
    tftp-server flash:cnu42.9-3-1ES19.sbn
    tftp-server flash:cvm42sccp.9-3-1ES19.sbn
    tftp-server flash:dsp42.9-3-1ES19.sbn
    tftp-server flash:jar42sccp.9-3-1ES19.sbn
    tftp-server flash:term42.default.loads
    tftp-server flash:term62.default.loads
    tftp-server flash:SCCP45.9-3-1SR3-1S.loads
    tftp-server flash:apps45.9-3-1ES19.sbn
    tftp-server flash:cnu45.9-3-1ES19.sbn
    tftp-server flash:cvm45sccp.9-3-1ES19.sbn
    tftp-server flash:dsp45.9-3-1ES19.sbn
    tftp-server flash:jar45sccp.9-3-1ES19.sbn
    tftp-server flash:term45.default.loads
    tftp-server flash:term65.default.loads
    tftp-server flash:/Ringtones/Ringlist.xml alias Ringlist.xml
    tftp-server flash:/Ringtones/DistinctiveRingList.xml alias DistinctiveRingList.x
    ml
    tftp-server flash:sip9971.9-4-1-9.loads
    tftp-server flash:kern9971.9-4-1-9.sebn
    tftp-server flash:rootfs9971.9-4-1-9.sebn
    tftp-server flash:dkern9971.100609R2-9-4-1-9.sebn
    tftp-server flash:sboot9971.031610R1-9-4-1-9.sebn
    tftp-server flash:skern9971.022809R2-9-4-1-9.sebn
    tftp-server flash:/g4-tones.xml alias United_States/g4-tones.xml
    tftp-server flash:/gd-sip.jar alias English_United_States/gd-sip.jar
    control-plane
    mgcp profile default
    telephony-service
    max-ephones 24
    max-dn 48
    ip source-address 172.25.140.1 port 2000
    cnf-file location flash:
    load 7960-7940 P00308010200
    load 7942 SCCP42.9-3-1SR3-1S.loads
    load 7945 SCCP45.9-3-1SR3-1S.loads
    load 7962 SCCP42.9-3-1SR3-1S.loads
    load 7965 SCCP45.9-3-1SR3-1S.loads
    max-conferences 8 gain -6
    dn-webedit
    transfer-system full-consult
    create cnf-files version-stamp 7960 Feb 11 2014 07:18:32
    ephone-dn  1
    number 1001
    description Phone 1
    name Phone 1
    hold-alert 30 originator
    ephone-dn  2
    number 1002
    description Phone 2
    name Phone 2
    hold-alert 30 originator
    ephone-dn  3
    number 1003
    description Phone 3
    name Phone 3
    hold-alert 30 originator
    ephone  1
    device-security-mode none
    mac-address 001C.58FB.6E0F
    button  1:1
    ephone  2
    device-security-mode none
    mac-address 0014.A981.7F8A
    button  1:2
    ephone  3
    device-security-mode none
    mac-address 0006.5356.A4B8
    button  1:3
    alias exec con conf t
    alias exec sib show ip int brief
    alias exec srb show run | b
    alias exec sri show run int
    line con 0
    exec-timeout 0 0
    logging synchronous
    line aux 0
    line vty 0 4
    privilege level 15
    login local
    transport input telnet ssh
    transport output telnet ssh
    line vty 5 15
    privilege level 15
    login local
    transport input telnet ssh
    transport output telnet ssh
    scheduler allocate 20000 1000
    ntp master 1
    end
    C2811#

    VPN is not Configured prints on all phones now with the built-in VPN client if VPN isn't configured.  That's normal and is just cosmetic.  That should not be causing your registration issues.

  • Cisco SIP Phone 9971 won't register on CME 8.6

    Hello,
    I'm facing a very strange problem:
    a Cisco SIP Phone 9971 won't register on CME 8.6 running on a 2811
    I have read all the related-postings to this and other Forum, but I have not been able to solve it.
    One of the "potential solutions" was to make sure that the Phone had a Line configured.
    But I think that the commands voice register dn  and  voice register pool are properly configured (see config below)
    So frankly, I have no idea what I could be missing.
    I'm pasting the Router's config.
    I hope somebody is able to point me in the right direction.
    Here is the config.  Thank you!
    C2811#sh run
    Building configuration...
    version 15.1
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    hostname C2811
    no aaa new-model
    dot11 syslog
    ip source-route
    ip cef
    ip dhcp excluded-address 172.25.140.1 172.25.140.10
    ip dhcp excluded-address 172.35.140.1 172.35.140.10
    ip dhcp pool Data
    network 172.25.140.0 255.255.255.0
    default-router 172.25.140.1
    option 150 ip 172.25.140.1
    dns-server 172.25.140.1
    ip dhcp pool Voice
    network 172.35.140.0 255.255.255.0
    default-router 172.35.140.1
    option 150 ip 172.35.140.1
    dns-server 172.35.140.1
    no ip domain lookup
    no ipv6 cef
    multilink bundle-name authenticated
    voice service voip
    allow-connections sip to sip
    sip
      registrar server expires max 3600 min 120
    voice register global
    mode cme
    source-address 172.25.140.1 port 5060
    max-dn 40
    max-pool 42
    load 9971 sip9971.9-4-1-9.loads
    authenticate register
    authenticate realm cisco
    tftp-path flash:
    create profile sync 0004820400584603
    voice register dn  1
    number 1010
    allow watch
    name Phone10
    label Phone10
    mwi
    voice register pool  1
    id mac 189C.5DB6.BD09
    type 9971
    number 1 dn 1
    presence call-list
    dtmf-relay rtp-nte
    username adm password adm
    call-forward b2bua busy 68600
    codec g711ulaw
    no vad
    camera
    video
    voice-card 0
    crypto pki token default removal timeout 0
    crypto pki trustpoint TP-self-signed-1879153754
    enrollment selfsigned
    subject-name cn=IOS-Self-Signed-Certificate-1879153754
    revocation-check none
    rsakeypair TP-self-signed-1879153754
    crypto pki certificate chain TP-self-signed-1879153754
    certificate self-signed 01
    (details ommited)
    license udi pid CISCO2811 sn FTX1146A44H
    username admin privilege 15 password 0 admin
    redundancy
    interface FastEthernet0/0
    no ip address
    duplex auto
    speed auto
    interface FastEthernet0/0.25
    description Data VLAN
    encapsulation dot1Q 25
    ip address 172.25.140.1 255.255.255.0
    interface FastEthernet0/0.35
    description Voice VLAN
    encapsulation dot1Q 35
    ip address 172.35.140.1 255.255.255.0
    interface FastEthernet0/1
    no ip address
    shutdown
    duplex auto
    speed auto
    ip forward-protocol nd
    ip http server
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 600 life 86400 requests 10000
    tftp-server flash:P00308010200.bin
    tftp-server flash:P00308010200.sbn
    tftp-server flash:P00308010200.sb2
    tftp-server flash:P00308010200.loads
    tftp-server flash:SCCP42.9-3-1SR3-1S.loads
    tftp-server flash:apps42.9-3-1ES19.sbn
    tftp-server flash:cnu42.9-3-1ES19.sbn
    tftp-server flash:cvm42sccp.9-3-1ES19.sbn
    tftp-server flash:dsp42.9-3-1ES19.sbn
    tftp-server flash:jar42sccp.9-3-1ES19.sbn
    tftp-server flash:term42.default.loads
    tftp-server flash:term62.default.loads
    tftp-server flash:SCCP45.9-3-1SR3-1S.loads
    tftp-server flash:apps45.9-3-1ES19.sbn
    tftp-server flash:cnu45.9-3-1ES19.sbn
    tftp-server flash:cvm45sccp.9-3-1ES19.sbn
    tftp-server flash:dsp45.9-3-1ES19.sbn
    tftp-server flash:jar45sccp.9-3-1ES19.sbn
    tftp-server flash:term45.default.loads
    tftp-server flash:term65.default.loads
    tftp-server flash:/Ringtones/Ringlist.xml alias Ringlist.xml
    tftp-server flash:/Ringtones/DistinctiveRingList.xml alias DistinctiveRingList.x
    ml
    tftp-server flash:sip9971.9-4-1-9.loads
    tftp-server flash:kern9971.9-4-1-9.sebn
    tftp-server flash:rootfs9971.9-4-1-9.sebn
    tftp-server flash:dkern9971.100609R2-9-4-1-9.sebn
    tftp-server flash:sboot9971.031610R1-9-4-1-9.sebn
    tftp-server flash:skern9971.022809R2-9-4-1-9.sebn
    tftp-server flash:/g4-tones.xml alias United_States/g4-tones.xml
    tftp-server flash:/gd-sip.jar alias English_United_States/gd-sip.jar
    control-plane
    mgcp profile default
    telephony-service
    max-ephones 24
    max-dn 48
    ip source-address 172.25.140.1 port 2000
    cnf-file location flash:
    load 7960-7940 P00308010200
    load 7942 SCCP42.9-3-1SR3-1S.loads
    load 7945 SCCP45.9-3-1SR3-1S.loads
    load 7962 SCCP42.9-3-1SR3-1S.loads
    load 7965 SCCP45.9-3-1SR3-1S.loads
    max-conferences 8 gain -6
    dn-webedit
    transfer-system full-consult
    create cnf-files version-stamp 7960 Feb 11 2014 07:18:32
    ephone-dn  1
    number 1001
    description Phone 1
    name Phone 1
    hold-alert 30 originator
    ephone-dn  2
    number 1002
    description Phone 2
    name Phone 2
    hold-alert 30 originator
    ephone-dn  3
    number 1003
    description Phone 3
    name Phone 3
    hold-alert 30 originator
    ephone  1
    device-security-mode none
    mac-address 001C.58FB.6E0F
    button  1:1
    ephone  2
    device-security-mode none
    mac-address 0014.A981.7F8A
    button  1:2
    ephone  3
    device-security-mode none
    mac-address 0006.5356.A4B8
    button  1:3
    alias exec con conf t
    alias exec sib show ip int brief
    alias exec srb show run | b
    alias exec sri show run int
    line con 0
    exec-timeout 0 0
    logging synchronous
    line aux 0
    line vty 0 4
    privilege level 15
    login local
    transport input telnet ssh
    transport output telnet ssh
    line vty 5 15
    privilege level 15
    login local
    transport input telnet ssh
    transport output telnet ssh
    scheduler allocate 20000 1000
    ntp master 1
    end
    C2811#

    Thank you for your reply.
    I did some debugs and the results are very strange!
    This is what I got:
    Feb 24 18:01:12.219: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
    Sent:
    SIP/2.0 400 Bad Request
    Via: SIP/2.0/UDP 172.35.140.12:5060;branch=z9hG4bK08011844
    From: ;tag=189c5db6bd09000260cf3daf-289a76d1
    To: ;tag=52488-160A
    Date: Mon, 24 Feb 2014 18:01:12 GMT
    Call-ID: [email protected]
    CSeq: 1000 REFER
    Content-Length: 0
    Contact:
    Feb 24 18:01:12.291: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
    Received:
    REGISTER sip:172.25.140.1 SIP/2.0
    Via: SIP/2.0/UDP 172.35.140.12:5060;branch=z9hG4bK1e9ad079
    From: ;tag=189c5db6bd0900032df02e9c-25d79707
    To:
    Call-ID: [email protected]
    Max-Forwards: 70
    Date: Fri, 01 Jan 1982 00:02:41 GMT
    CSeq: 101 REGISTER
    User-Agent: Cisco-CP9971/9.4.1
    Contact: ;+sip.instance="
    000000-0000-0000-0000-189c5db6bd09>";+u.sip!devicename.ccm.cisco.com="SEP189C5DB
    6BD09";+u.sip!model.ccm.cisco.com="493";video
    Supported: replaces,join,sdp-anat,norefersub,resource-priority,extended-refer,X-
    cisco-callinfo,X-cisco-serviceuri,X-cisco-escapecodes,X-cisco-service-control,X-
    cisco-srtp-fallback,X-cisco-monrec,X-cisco-config,X-cisco-sis-6.0.2,X-cisco-xsi-
    8.0.1
    Content-Length: 0
    Reason: SIP;cause=200;text="cisco-alarm:22 Name=SEP189C5DB6BD09 ActiveLoad=sip99
    71.9-4-1-9.loads InactiveLoad=sip9971.9-3-2SR1-1.loads Last=reset-reset"
    Expires: 3600
    Feb 24 18:01:12.395: voice_reg_get_reg_expires_timer: no voice register pool found
    Feb 24 18:01:12.395: VOICE_REG_POOL: Register request for (1010) from (172.35.140.12)
    Feb 24 18:01:12.395: VOICE_REG_POOL: Contact matches pool 1 number list 1
    Feb 24 18:01:12.395: VOICE_REG_POOL: No entry for (172.35.140.12) found in srst contact table
    Feb 24 18:01:12.395: VOICE_REG_POOL: key(1010) contact(172.35.140.12:5060) add to contact table
    Feb 24 18:01:12.395: VOICE_REG_POOL: No entry for (1010) found in contact table
    Feb 24 18:01:12.399: VOICE_REG_POOL: key(1010) contact(172.35.140.12) added to contact table
    Feb 24 18:01:12.399: VOICE_REG_POOL: key(172.35.140.12) contact(1010) add to srst contact table
    Feb 24 18:01:12.399: VOICE_REG_POOL: No entry for (172.35.140.12) found in srst contact table
    Feb 24 18:01:12.399: VOICE_REG_POOL: key(172.35.140.12) contact(1010) added to srst contact table
    Feb 24 18:01:12.399: VOICE_REG_POOL pool->tag(1), dn->tag(1), submask(1)
    But right after these errors, I get the following:
    Feb 24 18:01:12.399: VOICE_REG_POOL: Creating param container for dial-peer 4000
    1.VOICE_REG_POOL pool->tag(1), dn->tag(1), submask(1)
    VOICE_REG_POOL pool_tag(1), dn_tag(1)
    Feb 24 18:01:12.399: VOICE_REG_POOL: Created dial-peer entry of type 0
    Feb 24 18:01:12.399: VOICE_REG_POOL: Registration successful for 1010, registration id is 1
    Feb 24 18:01:12.411: VOICE_REG_POOL: Contact matches pool 1 number list 1
    Feb 24 18:01:12.411: VOICE_REG_POOL: GW SIS: X-cisco-cme-sis-1.0.0
    Feb 24 18:01:12.411: VOICE REGISTER POOL-1 has registered.
                                   Name:SEP189C5DB6BD09 IP:172.35.140.12  DeviceType:Phone
    Feb 24 18:01:12.411: VOICE_REG_POOL: Pool[1]: service-control (reset type: 2) message sent to sip:[email protected]
    Feb 24 18:01:12.411: voice_reg_privacy_update_to_phone: delay sending privacy update during bulk registration
    Feb 24 18:01:12.415: //1/7B0070C28003/SIP/Msg/ccsipDisplayMsg:
    ====================
    And when I do a sh voice register pool, I get the following:
    C2811#sh voice register pool  1
    Pool Tag 1
    Config:
      Mac address is 189C.5DB6.BD09
      Type is 9971
      Number list 1 : DN 1
      Proxy Ip address is 0.0.0.0
      Current Phone load version is Cisco-CP9971/9.4.1
      DTMF Relay is enabled, rtp-nte
      Call Waiting is enabled
      DnD is disabled
      Video is enabled
      Camera is enabled
      Busy trigger per button value is 0
      call-forward b2bua busy 68600
      keep-conference is enabled
      registration expires timer max is 3600 and min is 120
      username adm password adm
      kpml signal is enabled
      Lpcor Type is none
      blf call list is enabled
      Transport type is udp
      service-control mechanism is supported
      registration Call ID is [email protected]
      Registration method: per line
      Privacy feature is not configured.
      Privacy button is disabled
      active primary line is: 1010
      contact IP address: 172.35.140.12 port 5060
      Phone SIS Version:  6.0.2
      GW SIS Version:  1.0.0
    Dialpeers created:
    Dial-peers for Pool 1:
    dial-peer voice 40001 voip
    destination-pattern 1010
    session target ipv4:172.35.140.12:5060
    session protocol sipv2
    dtmf-relay rtp-nte
    digit collect kpml
    codec  g711ulaw bytes 160
    no vad
      call-fwd-busy        68600
      after-hours-exempt   FALSE
    Statistics:
      Active registrations  : 4
      Total SIP phones registered: 1
      Total Registration Statistics
        Registration requests  : 4
        Registration success   : 4
        Registration failed    : 0
        unRegister requests    : 0
        unRegister success     : 0
        unRegister failed      : 0
        Attempts to register
               after last unregister : 0
        Last register request time   : 18:11:43.551 UTC Mon Feb 24 2014
        Last unregister request time :
        Register success time        : 18:11:43.551 UTC Mon Feb 24 2014
        Unregister success time      :
    C2811#
    So apparently the Phone is actually registered!
    However, the Phone screens still shows this message: Phone Not Registered.
    So frankly I don't understand what's going on!
    I really hope somebody can help.  Thanks!

  • Is it possible to have a phone line connected to a Mac Mini (OS X10.8.2) so you can use your computer with Parallels (Windows xp) to dial into a modem to download data being collected and stored at the remote location?

    Is it possible to have a phone line connected to a Mac Mini (OS X10.8.2) so you can use your computer with Parallels (Windows xp) to dial into a modem to download data being collected and stored at the remote location?

    Hi, do you mean a real Dial-up Modem as in the old days?
    As I recall, the Apple USB Modem won't work in 64 bit OSes, but there are others that will, I think this is one of them...
    http://www.zoomtel.com/products/dial_up_external_usb.html
    Or is the Modem on the other end Cable/DSL/FiberOptic?

  • SIP Phone 9971

    I have CUCM (9.1.2) and Sip phone 9971.
    When user hangup phone, and try to dial phone number to PSTN, he waiting about 15 seconds before sip phone make a call. I would to make this time about 1 or 2 seconds. If he call to Polycom server, he does not waiting any time.
    I changed any timer - no effects.
    I apply "Sip dial rules" nothing changed.
    Can anybody tell me how i can fix it?

    Is only one user impacted. Normally delays in the dialing are due to below:
    1) Overlap in dial plan or
    2) Interdigit timeout  T302 (default is 15 sec) that comes into play specially if you are hitting a variable route pattern
    So either you can check your dial plan and have specific route patterns or you can change the inter digit time out to something less 5 secs maybe according to your issue. (3 secs is the minimum value you can configure)
    To change inter digit timeout T302 go to - Service Parameters, Call Manager service and search T302. Change it to the required value (its in msecs)
    -Terry
    Please rate all helpful posts

  • X-lite Sip Phone Registration Rejected

    I have an x-lite sip phone that i added as a third party(basic) sip device on cisco call manager, settings are:
    UserID: <Extn No on CUCM>
    Domain:<ip address of the CUCM>
    Password:<CUCM Digest Credentials>
    Authorization Name: <UserID on CUCM>
    No Domain Proxy
    What could be missing?

    Take a look at Mr. Bell's writeup on this:
    http://www.netcraftsmen.net/component/content/article/70-unified-communications/766-sip-endpoints-in-cisco-cucm-x-lite-as-an-example.html
    Please remember to rate helpful responses and identify helpful or correct answers.

  • SIP phone registering on SIP trunk

    Hi,
    i have a UC 500 connected to our phone provider using a SIP trunk.
    All the phones are SPA508 G
    All is working fine !
    Then, some days ago i added a SIP phone (extention 350) on the UC500, that also worked fine, and then after some minutes all our incoming/outgoing calls were blocked.
    I called my provider that told me that our IP was banned because they have seen to much registration attempt from a bad user that was "350"
    I can confirm with a "sh sip-ua register status" command that i had two sip registration : my SIP trunk and the SIP phone
    Then it seems that the UC 500 is trying to register the SIP phone on the SIP trunk ?
    What am i doing wrong ?
    Is there a command to avoid that ?
    Bellow is how the SIP phone and the SIP trunk are configured
    Many thanks for your help, i was unable to find anything about that, but i guess somebody already had this problem !
    The SIP phone -------------------------------------------------------------------------
    voice service voip
     allow-connections h323 to h323
     allow-connections h323 to sip
     allow-connections sip to h323
     allow-connections sip to sip
     supplementary-service h450.12
     fax protocol none
     modem passthrough nse codec g711ulaw
     sip
      registrar server expires max 3600 min 120
      no update-callerid
    voice class codec 1
     codec preference 1 g711ulaw
     codec preference 2 g729r8
    voice register global
     mode cme
     source-address 10.1.1.1 port 5060
     max-dn 20
     max-pool 20
     load 9971 sip9971.9-2-2
     load 9951 sip9951.9-2-2
     load 8961 sip8961.9-2-2
     load 7971 term71.default
     authenticate register
     authenticate realm xxxxxx.com
     timezone 13
     hold-alert
     mwi stutter
     mwi reg-e164
     create profile sync 0636240803635305
    voice register dn  1
     number 350
     name Conference
     label Conference
    voice register pool  1
     id mac 1234.1234.1234
     number 1 dn 1
     username 350 password 1234
     codec g711ulaw
    The SIP trunk ----------------------------------------------------------------------
    sip-ua
     credentials username user1234 password 1234 realm sipgw9.provider.com
     authentication username user1234 password 1234 no remote-party-id
     retry invite 2
     retry register 10
     timers connect 100
     registrar dns:sipgw9.provider.com expires 3600
     sip-server dns:sipgw9.provider.com

    I'm still searching on the forum, and maybe i found somthing related to my problem, not sure... any advice ?
    Disable outbound proxy on voice register global as by default it will use the outbound proxy configured on the system which would not make sense
    voice register global
      no outbound-proxy
    found there : https://supportforums.cisco.com/discussion/10760741/uc500-sip-server-and-sip-trunk

  • I need helping!!! configuring RDP access to my local server from a remote location on my Cisco ASA 5505 Firewall.

    I need helping configuring RDP access to my local server from a remote location on my Cisco ASA 5505 Firewall.
    I have attempted to configure rdp access but it does not seem to be working for me Could I please ask someone to help me modify my current configuration to allow this? Please do step by step as I could use all the help I could get.
    I need to allow the following IP addresses to have RDP access to my server:
    66.237.238.193-66.237.238.222
    69.195.249.177-69.195.249.190
    69.65.80.240-69.65.80.249
    My external WAN server info is - 99.89.69.333
    The internal IP address of my server is - 192.168.6.2
    The other server shows up as 99.89.69.334 but is working fine.
    I already added one server for Static route and RDP but when I try to put in same commands it doesnt allow me to for this new one. Please take a look at my configuration file and give me the commands i need in order to put this through. Also please tell me if there are any bad/conflicting entries.
    THE FOLLOWING IS MY CONFIGURATION FILE
    Also I have modified IP information so that its not the ACTUAL ip info for my server/network etc... lol for security reasons of course
    Also the bolded lines are the modifications I made but that arent working.
    ASA Version 7.2(4)
    hostname ciscoasa
    domain-name default.domain.invalid
    enable password DowJbZ7jrm5Nkm5B encrypted
    passwd 2KFQnbNIdI.2KYOU encrypted
    names
    interface Vlan1
    nameif inside
    security-level 100
    ip address 192.168.6.254 255.255.255.0
    interface Vlan2
    nameif outside
    security-level 0
    ip address 99.89.69.233 255.255.255.248
    interface Ethernet0/0
    switchport access vlan 2
    interface Ethernet0/1
    interface Ethernet0/2
    interface Ethernet0/3
    interface Ethernet0/4
    interface Ethernet0/5
    interface Ethernet0/6
    interface Ethernet0/7
    ftp mode passive
    dns server-group DefaultDNS
    domain-name default.domain.invalid
    object-group network EMRMC
    network-object 10.1.2.0 255.255.255.0
    network-object 192.168.10.0 255.255.255.0
    network-object 192.168.11.0 255.255.255.0
    network-object 172.16.0.0 255.255.0.0
    network-object 192.168.9.0 255.255.255.0
    object-group service RDP tcp
    description RDP
    port-object eq 3389
    object-group service GMED tcp
    description GMED
    port-object eq 3390
    object-group service MarsAccess tcp
    description MarsAccess
    port-object range pcanywhere-data 5632
    object-group service MarsFTP tcp
    description MarsFTP
    port-object range ftp-data ftp
    object-group service MarsSupportAppls tcp
    description MarsSupportAppls
    port-object eq 1972
    object-group service MarsUpdatePort tcp
    description MarsUpdatePort
    port-object eq 7835
    object-group service NM1503 tcp
    description NM1503
    port-object eq 1503
    object-group service NM1720 tcp
    description NM1720
    port-object eq h323
    object-group service NM1731 tcp
    description NM1731
    port-object eq 1731
    object-group service NM389 tcp
    description NM389
    port-object eq ldap
    object-group service NM522 tcp
    description NM522
    port-object eq 522
    object-group service SSL tcp
    description SSL
    port-object eq https
    object-group service rdp tcp
    port-object eq 3389
    access-list outside_1_cryptomap extended permit ip 192.168.6.0 255.255.255.0 object-group EMRMC
    access-list inside_nat0_outbound extended permit ip 192.168.6.0 255.255.255.0 192.168.0.0 255.255.0.0
    access-list inside_nat0_outbound extended permit ip 192.168.6.0 255.255.255.0 object-group EMRMC
    access-list outside_access_in extended permit tcp 69.16.158.128 255.255.255.128 host 99.89.69.334 eq pcanywhere-data
    access-list outside_access_in extended permit udp 69.16.158.128 255.255.255.128 host 99.89.69.334 eq pcanywhere-status
    access-list outside_access_in extended permit tcp 69.16.158.128 255.255.255.128 host 99.89.69.334 object-group RDP
    access-list outside_access_in extended permit tcp 69.16.158.128 255.255.255.128 192.168.6.0 255.255.255.0 eq ftp
    access-list outside_access_in extended permit tcp 69.16.158.128 255.255.255.128 192.168.6.0 255.255.255.0 eq ldap
    access-list outside_access_in extended permit tcp 69.16.158.128 255.255.255.128 192.168.6.0 255.255.255.0 eq h323
    access-list outside_access_in extended permit tcp 69.16.158.128 255.255.255.128 192.168.6.0 255.255.255.0 eq telnet
    access-list outside_access_in extended permit tcp 69.16.158.128 255.255.255.128 192.168.6.0 255.255.255.0 eq www
    access-list outside_access_in extended permit tcp 69.16.158.128 255.255.255.128 host 99.89.69.334 object-group SSL
    access-list outside_access_in extended permit tcp 69.16.158.128 255.255.255.128 192.168.6.0 255.255.255.0 object-group NM522
    access-list outside_access_in extended permit tcp 69.16.158.128 255.255.255.128 192.168.6.0 255.255.255.0 object-group NM1731
    access-list outside_access_in extended permit tcp 173.197.144.48 255.255.255.248 host 99.89.69.334 object-group RDP
    access-list outside_access_in extended permit tcp any interface outside eq 3389
    access-list outside_access_in extended permit tcp host 66.237.238.194 host 99.89.69.333
    access-list outside_access_in extended permit tcp host 66.237.238.194 host 99.89.69.333 object-group rdp
    access-list outside_access_in extended permit tcp any host 99.89.69.333 object-group rdp
    access-list out_in extended permit tcp any host 192.168.6.2 eq 3389
    pager lines 24
    logging enable
    logging asdm informational
    mtu inside 1500
    mtu outside 1500
    icmp unreachable rate-limit 1 burst-size 1
    asdm image disk0:/asdm-524.bin
    no asdm history enable
    arp timeout 14400
    global (outside) 1 interface
    nat (inside) 0 access-list inside_nat0_outbound
    nat (inside) 1 0.0.0.0 0.0.0.0
    static (inside,outside) tcp 99.89.69.334 3389 192.168.6.1 3389 netmask 255.255.255.255
    static (inside,outside) tcp interface 3389 192.168.6.2 3389 netmask 255.255.255.255
    access-group outside_access_in in interface outside
    route outside 0.0.0.0 0.0.0.0 99.89.69.338 1
    timeout xlate 3:00:00
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    http server enable
    http 192.168.6.0 255.255.255.0 inside
    http 0.0.0.0 0.0.0.0 outside
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart
    crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
    crypto map outside_map 1 match address outside_1_cryptomap
    crypto map outside_map 1 set peer 68.156.148.5
    crypto map outside_map 1 set transform-set ESP-3DES-MD5
    crypto map outside_map interface outside
    crypto isakmp enable outside
    crypto isakmp policy 10
    authentication pre-share
    encryption 3des
    hash md5
    group 1
    lifetime 86400
    crypto isakmp policy 30
    authentication pre-share
    encryption 3des
    hash md5
    group 2
    lifetime 86400
    telnet timeout 5
    ssh timeout 5
    console timeout 0
    dhcpd auto_config outside
    tunnel-group 68.156.148.5 type ipsec-l2l
    tunnel-group 68.156.148.5 ipsec-attributes
    pre-shared-key *
    class-map inspection_default
    match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
    parameters
      message-length maximum 512
    policy-map global_policy
    class inspection_default
      inspect dns preset_dns_map
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect rsh
      inspect rtsp
      inspect esmtp
      inspect sqlnet
      inspect skinny
      inspect sunrpc
      inspect sunrpc
      inspect xdmcp
      inspect sip
      inspect netbios
      inspect tftp
    service-policy global_policy global
    prompt hostname context
    Cryptochecksum:f47dfb2cf91833f0366ff572eafefb1d
    : end
    ciscoasa(config-network)#

    Unclear what did not work.  In your original post you include said some commands were added but don't work:
    static (inside,outside) tcp interface 3389 192.168.6.2 3389 netmask 255.255.255.255
    and later you state you add another command that gets an error:
    static (inside,outside) tcp 99.89.69.333 3389 192.168.6.2 3389 netmask 255.255.255.255
    You also stated that 99.89.69.333 (actually 99.89.69.233, guessing from the rest of your config and other posts) is your WAN IP address.
    The first static statement matches Cisco's documentation, which states that a static statement must use the 'interface' directive when you are trying to do static PAT utilizing the IP address of the interface.  Since 99.89.69.333 is the assigned IP address of your WAN interface, that may explain why the second statement fails.
    Any reason why you are using static PAT (including the port number 3389) instead of just skipping that directive?  Static PAT usually makes sense when you need to change the TCP port number.  In your example, you are not changing the TCP port 3389.

  • CUCM 8.6 Dropped call transfers involving SIP phones

    Hi All,
    I am a developer who has been tasked with figuring out why call transfers are being dropped by Cisco CUCM when the original call comes from a SIP phone.  This scenario works:
    Cisco phone calls another Cisco phone, which transfers the original call to a SIP phone
    These scenarios do not work:
    SIP phone calls Cisco phone, which transfers the original call to another Cisco phone
    SIP phone calls Cisco phone, which transfers the original call to another SIP phone
    I have researched the Call Manager traces to the best of my ability, and I see some info in there that could potentially point to the source of the problem.  I am just unable to understand what the trace means:
    10:23:08.672 |//SIP/SIPCdpc(1,74,2342)/ci=24377698/ccbId=175645/scbId=0/active_CcDisconnReq: ccDisconnReq.onBehalfOf=Media : ccDisconnReq.s.sv=2 : ccDisconnReq.c.cv=47 |1,100,63,1.93259^10.10.10.85^*
    10:23:08.672 |//SIP/Stack/Info/0x0/sipConstructContainerContext #### Created container=0xb0b42f58|1,100,71,1.1^*^*
    10:23:08.672 |//SIP/SIPCdpc(1,74,2342)/ci=24377698/ccbId=175645/scbId=0/appendReasonHdr: appendReasonHdr - Invalid Disconnect Cause(cause=47), No Reason Header Appended|1,100,63,1.93259^10.10.10.85^*
    10:23:08.672 |//SIP/SIPCdpc(1,74,2342)/ci=24377698/ccbId=175645/scbId=0/appendRPIDHdrForOriginalCalledParty: SIP device does not Support Orig Dialled Phone nego: 0|1,100,63,1.93259^10.10.10.85^*
    I have been wondering whether this could be a codec issue, however the SIP phones we are using are configured with the following codecs:
    G711U
    G711A
    G722
    ILBC
    GSM
    and our SIP software is  also set to accept the first codec offered by the remote side.  It seems from the SIP client logs that G722 is being used as the codec to communicate with the Cisco phones, but perhaps I'm misinterpreting.
    I have attached a CUCM trace of a call from a SIP phone (ext. 491) to a Cisco handset (ext. 170) where the Cisco handset attempts to transfer the call to another SIP phone (ext. 492).  The trace snippet shown above is from this log.
    I would really appreciate it if someone more experienced with VoIP/SIP/CUCM could take a look and offer any ideas on what the issue might be, and also how we might be able to address it.  I can try to provide more info about our CUCM configuration if needed.
    Thanks in advance!

    Leslie, so here is what I found from the traces....
    To understand the difference we need to understand how cucm performs call transfers from a sccp signalling point and a sip signalling point
    SCCP
    When the transfer key is pressed
    1. CUCM sends a CloseReceiveChannel and StopMediaTransmission to the IP phone involved in active media (referenced by the callids)
    NB, here CUCM updates the call state on the phone to a call state of 8 which is "Hold"
    2.CUCM tells the held party to listen MOH from MOH server
    3.CUCM establishes newcall leg with the intended transfered destination..Once this call is connected
    4.CUCM receives a new Transfer instruction from the transferring phone to connect the held party
    5..CUCM sends a CloseReceiveChannel between the held phone and MOH server (to tear down the media)
    6. Next CUCM sends a CloseReceiveChannel and StopMediaTransmission to the transfering party & transfered party to remove Xferring party from call
    7. finally CUCM sends OpenReceiveChannel between the original called party and the transfered party..and call is done
    For SIP signalling. when the first transfer key is pressed
    1. CUCM sends invite (re-invite) with an inactive SDP (a=inactive) to indicate a break in media path
    2. CUCM sends a Delayed offer to insert MOH or to resume Media stream
    NB: CUCM expects a sendrecv offer with SDP to the DO. (NB:if cucm gets an inactive offer SDP in the 200 OK instead of providing a send-recv offer SDP, the media path remains in an inactive state and causes calls to dropcall will drop),CUCM sends an ACK with sendonly to the 200 OK
    3.CUCM establishes newcall leg with the intended transfered destination..Once this call is connected
    4.CUCM receives a new Transfer instruction from the transferring phone to connect the held party
    5. Next CUCM sends a re-invite with an inactive SDP to indicate a break in media path to MOH (in attempt to complete transfer)
    6.Next CUCM sends an inactive SDP to indicate a break in media path between transfering party & transfered party to remove Xferring party from call
    7. Next CUCM sends a DO re-invite to connect the transfered party. The far end then sends 200 OK with the required SDP to connect the call
    Now having explained all of these, we need to look at where the call is failing for SIP-----SCCP----SIP calls without MTP
    lets look at succesful SCCP-----SCCP-----SIP without MTP
    Point 4 above
    ++++++++Extension 170 presses the transfer button to connect the two calls (Callid=24378483)+++++++++++++
    (0003395) SoftKeyEvent softKeyEvent=4(Trnsfer) lineInstance=1 callReference=24378483
    Point 5 above
    ++++Next CUCM closed the media between extension 160 and MOH server callid=24378480(this is the only active call on this callid)+++
    (0003396) CloseReceiveChannel conferenceID=24378480 passThruPartyID=16777845.  myIP: IpAddr.type:0 ipv4Addr:0x0a0a0a89(10.10.10.137)
    Point 6 Above
    +++++Next cucm closes the call between extension 170 and 490 callid=(24378483)++++++++
    (0003395) CloseReceiveChannel conferenceID=24378483 passThruPartyID=16777847.  myIP: IpAddr.type:0 ipv4Addr:0x0a0a0a8b(10.10.10.139)
    (0003395) StopMediaTransmission conferenceID=24378483 passThruPartyID=16777847.  myIP: IpAddr.type:0 ipv4Addr:0x0a0a0a8b(10.10.10.139)
    Point 6 above for the sip side (since the destination is SIP, to tear down media to SCCP phone, so as to connect the caller to the xfered party)
    +++++++Next CUCM sends a re-invite with a=inactive SDP to the sip phone ++++++++++++
    //SIP/SIPTcp/wait_SdlSPISignal: Outgoing SIP TCP message to 10.10.10.104 on port 62220 index 1890
    [885626,NET]
    INVITE sip:[email protected]:62220;transport=tcp SIP/2.0
    Via: SIP/2.0/TCP 10.10.10.195:5060;branch=z9hG4bK23332dbee978
    From: ;tag=192115~d8e94532-127d-4dca-bba0-64b1675da032-24378484
    o=CiscoSystemsCCM-SIP 192115 2 IN IP4 10.10.10.195
    s=SIP Call
    c=IN IP4 0.0.0.0
    m=audio 24560 RTP/AVP 9 101
    a=rtpmap:9 G722/8000
    a=ptime:20
    a=inactive-----------------------------------------------------Inactive
    Still part of Point 6 for SIP signalling
    ++++++++++++Next sip phone responds with a 200 OK recevonly SDP +++++++++++++++++++
    //SIP/SIPTcp/wait_SdlReadRsp: Incoming SIP TCP message from 10.10.10.104 on port 62220 index 1890 with 683 bytes:
    [885628,NET]
    SIP/2.0 200 OK
    v=0
    o=- 18077 11099 IN IP4 10.10.10.104
    s=yasdjip
    c=IN IP4 10.10.10.104
    t=0 0
    a=ptime:20
    a=recvonly-------------------------------------a=recvonly
    Finally Point 7 above..
    +++++++++++++=Next cucm sends a DO re-invite to extension 492-sip phone++++++++++
    //SIP/SIPTcp/wait_SdlSPISignal: Outgoing SIP TCP message to 10.10.10.104 on port 62220 index 1890
    [885630,NET]
    INVITE sip:[email protected]:62220;transport=tcp SIP/2.0
    Via: SIP/2.0/TCP 10.10.10.195:5060;branch=z9hG4bK233534ffec4a
    From: ;tag=192115~d8e94532-127d-4dca-bba0-64b1675da032-24378484
    To: ;tag=5B0E9816C2CA6D70F3166FB972EDE4C2
    +++++++Next we get a 200 OK from sip phone with sdp=sendrecv+++++++++=
    /SIP/SIPTcp/wait_SdlReadRsp: Incoming SIP TCP message from 10.10.10.104 on port 62220 index 1890 with 683 bytes:
    [885634,NET]
    SIP/2.0 200 OK
    Via: SIP/2.0/TCP 10.10.10.195:5060;branch=z9hG4bK233534ffec4a
    Contact:
    From: ;tag=192115~d8e94532-127d-4dca-bba0-64b1675da032-24378484
    Call-ID: [email protected]
    v=0
    o=- 18077 11099 IN IP4 10.10.10.104
    s=yasdjip
    c=IN IP4 10.10.10.104
    t=0 0
    m=audio 16574 RTP/AVP 9 101
    a=rtpmap:101 TELEPHONE-EVENT/8000
    a=fmtp:101 0-15
    a=ptime:20
    a=sendrecv
    +Now CUCM sends an OpenReceiveChannel and start media xmission to sccp phone (callid=24378480) with media parameters of sip phone++++++
    (0003396) OpenReceiveChannel conferenceID=24378480 passThruPartyID=16777848 millisecondPacketSize=20 compressionType=6(Media_Payload_G722_64k) RFC2833PayloadType=101 qualifierIn=? sourceIpAddr=IpAddr.type:0 ipAddr:0x0a0a0a68000000000000000000000000(10.10.10.104). myIP: IpAddr.type:0 ipv4Addr:0x0a0a0a89(10.10.10.137)
    (0003396) startMediaTransmission conferenceID=24378480 passThruPartyID=16777848 remoteIpAddress=IpAddr.type:0 ipAddr:0x0a0a0a68000000000000000000000000(10.10.10.104)
    remotePortNumber=16574 milliSecondPacketSize=20 compressType=6(Media_Payload_G722_64k) RFC2833PayloadType=101 qualifierOut=?. myIP: IpAddr.type:0 ipv4Addr:0x0a0a0a89(10.10.10.137)
    +++++++++++=Next Phone sends its ACK+++++++++++++++
    (0003396) OpenReceiveChannelAck Status=0, IpAddr=IpAddr.type:0 ipAddr:0x0a0a0a89000000000000000000000000(10.10.10.137), Port=20352, PartyID=16777848
    +++++++++++=Next CUCM sends ACK to 200 OK from SIP Phone+++++++++++
    //SIP/SIPTcp/wait_SdlSPISignal: Outgoing SIP TCP message to 10.10.10.104 on port 62220 index 1890
    [885635,NET]
    ACK sip:[email protected]:62220;transport=tcp SIP/2.0
    Via: SIP/2.0/TCP 10.10.10.195:5060;branch=z9hG4bK23366067b8c0
    From: ;tag=192115~d8e94532-127d-4dca-bba0-64b1675da032-24378484
    To: ;tag=5B0E9816C2CA6D70F3166FB972EDE4C2
    Date: Tue, 19 Feb 2013 21:44:45 GMT
    Call-ID: [email protected]
    Max-Forwards: 70
    CSeq: 103 ACK
    Allow-Events: presence
    Content-Type: application/sdp
    Content-Length: 237
    v=0
    o=CiscoSystemsCCM-SIP 192115 3 IN IP4 10.10.10.195
    s=SIP Call
    c=IN IP4 10.10.10.137
    b=TIAS:64000
    b=AS:64
    t=0 0
    m=audio 20352 RTP/AVP 9 101
    a=rtpmap:9 G722/8000
    a=ptime:20
    a=rtpmap:101 telephone-event/8000
    a=fmtp:101 0-15
    Now at this point all is well...and the call is connected....
    Now here is where the call is failing on the SIP-SCCP-SIP call without MTP
    From Point 2 above, CUCM sends a DO to insert MOH, and then gets response, then sends an ACK to 200 Ok back to SIP Phone..
    //SIP/SIPTcp/wait_SdlSPISignal: Outgoing SIP TCP message to 10.10.10.104 on port 53361 index 1810
    [881160,NET]
    ACK sip:[email protected]:53361;transport=tcp SIP/2.0
    Via: SIP/2.0/TCP 10.10.10.195:5060;branch=z9hG4bK22035ecc1fcb
    From: ;tag=190666~d8e94532-127d-4dca-bba0-64b1675da032-24378214
    To: "492" ;tag=97C34E1FB9A11F83DD8D8F5BA4C87C57
    Date: Tue, 19 Feb 2013 17:38:50 GMT
    Call-ID: 1CCA5149B966DC89AE0F752B8EF86480BC7102DB
    Max-Forwards: 70
    CSeq: 102 ACK
    o=CiscoSystemsCCM-SIP 190666 3 IN IP4 10.10.10.195
    s=SIP Call
    c=IN IP4 10.10.10.195---------------------------------------IP address of MOH server
    t=0 0
    m=audio 4000 RTP/AVP 0--------------------------------MOH port 4000
    a=rtpmap:0 PCMU/8000
    a=ptime:20
    a=sendonly---------------------------------------------------------sendonly
    +++++NOW Point 6 above (SIP) CUCM sends a=inactive to break media path to MOH server to connect caller and xfered party++++++
    //SIP/SIPTcp/wait_SdlSPISignal: Outgoing SIP TCP message to 10.10.10.104 on port 53361 index 1810
    [881161,NET]
    INVITE sip:[email protected]:53361;transport=tcp SIP/2.0
    Via: SIP/2.0/TCP 10.10.10.195:5060;branch=z9hG4bK22045bb7f918
    From: ;tag=190666~d8e94532-127d-4dca-bba0-64b1675da032-24378214
    To: "492" ;tag=97C34E1FB9A11F83DD8D8F5BA4C87C57
    Date: Tue, 19 Feb 2013 17:39:04 GMT
    Call-ID: 1CCA5149B966DC89AE0F752B8EF86480BC7102DB
    Supported: timer,resource-priority,replaces
    Min-SE:  1800
    User-Agent: Cisco-CUCM8.6
    Allow: INVITE, OPTIONS, INFO, BYE, CANCEL, ACK, PRACK, UPDATE, REFER, SUBSCRIBE, NOTIFY
    CSeq: 103 INVITE
    Max-Forwards: 70
    Expires: 180
    Allow-Events: presence
    Remote-Party-ID: ;party=calling;screen=yes;privacy=off
    Contact:
    Content-Type: application/sdp
    Content-Length: 164
    v=0
    o=CiscoSystemsCCM-SIP 190666 4 IN IP4 10.10.10.195
    s=SIP Call
    c=IN IP4 0.0.0.0--------------------------------------------------------------------Media IP is 0.0.0.0
    t=0 0
    m=audio 4000 RTP/AVP 0
    a=rtpmap:0 PCMU/8000
    a=ptime:20
    a=inactive---------------------------------------------------------------------media inactive
    At this point, we should get a response back from the sip phone...
    and here is what we got..
    ++Trying which is expected++++
    //SIP/SIPTcp/wait_SdlReadRsp: Incoming SIP TCP message from 10.10.10.104 on port 53361 index 1810 with 331 bytes:
    [881162,NET]
    SIP/2.0 100 Trying
    Via: SIP/2.0/TCP 10.10.10.195:5060;branch=z9hG4bK22045bb7f918
    From: ;tag=190666~d8e94532-127d-4dca-bba0-64b1675da032-24378214
    Call-ID: 1CCA5149B966DC89AE0F752B8EF86480BC7102DB
    CSeq: 103 INVITE
    To: "492" ;tag=97C34E1FB9A11F83DD8D8F5BA4C87C57
    Content-Length: 0
    ++++++++Then we get a BYE+++++++++++++++
    /SIP/SIPTcp/wait_SdlReadRsp: Incoming SIP TCP message from 10.10.10.104 on port 53361 index 1810 with 576 bytes:
    [881163,NET]
    BYE sip:[email protected]:5060;transport=tcp SIP/2.0
    Via: SIP/2.0/TCP 10.10.10.104:53361;branch=z9hG4bKa2vdQvR7J9OiMyjU;rport
    Contact:
    Max-Forwards: 70
    From: "492" ;tag=97C34E1FB9A11F83DD8D8F5BA4C87C57
    Allow: OPTIONS, INVITE, ACK, REFER, CANCEL, BYE, NOTIFY
    Supported: replaces, path
    User-Agent: Acrobits Softphone Business/2.4.8
    To: ;tag=190666~d8e94532-127d-4dca-bba0-64b1675da032-24378214
    Call-ID: 1CCA5149B966DC89AE0F752B8EF86480BC7102DB
    CSeq: 3 BYE
    Content-Length: 0
    So this is the root cause of the problem. Your SIP phone does not know how to respond to multiple media break between it and the MOH server.
    The difference between this and the succesful SCCP-SIP--SCCP, is that the held party was a sccp phone, hence the sip phone only has to process one a=inactive SDP message, where as in the SIP-SCCP-SIP, the help party was sip, so the sip phone has to process two a=inactive SDP messages
    Now what is the difference when MTP is involved! A Big difference. MTP stays in the media path. So there is never a break in media and no inactive SDP attribute is sent. The flow looks like below:
    for the initial call...The SIP phone sends its media to MTP and likewise the SCCP phone
    SIP------Media------MTP------------Media-------SCCP Phone
    When the new destination is dialled and transfer is commited,
    SIP-------------media----MTP--------media---------MTP
    The final invoite sent to connect 492 and 491 has MTP as the IP address to connect Media to.
    ++++++++Ivite to 492 ++++++++++++++
    INVITE sip:[email protected]:61303;transport=tcp SIP/2.0
    Via: SIP/2.0/TCP 10.10.10.195:5060;branch=z9hG4bK231a3b24b862
    From: ;tag=192048~d8e94532-127d-4dca-bba0-64b1675da032-24378472
    To: ;tag=78FF5BF6C019A55EA020B69BB6A767E2
    Date: Tue, 19 Feb 2013 21:24:59 GMT
    Call-ID: [email protected]
    Supported: timer,resource-priority,replaces
    Min-SE:  1800
    User-Agent: Cisco-CUCM8.6
    Allow: INVITE, OPTIONS, INFO, BYE, CANCEL, ACK, PRACK, UPDATE, REFER, SUBSCRIBE, NOTIFY
    CSeq: 102 INVITE
    Max-Forwards: 70
    Expires: 180
    Allow-Events: presence
    Remote-Party-ID: ;party=calling;screen=yes;privacy=off
    Contact:
    Content-Type: application/sdp
    Content-Length: 214
    v=0
    o=CiscoSystemsCCM-SIP 192048 1 IN IP4 10.10.10.195
    s=SIP Call
    c=IN IP4 10.10.10.195---------------------------------------------------------------the MTP ip address
    t=0 0
    m=audio 25038 RTP/AVP 0 101
    a=rtpmap:0 PCMU/8000
    a=ptime:20
    a=rtpmap:101 telephone-event/8000
    a=fmtp:101 0-15
    +++++++Invite to 491 +++++++++++++++++
    //SIP/SIPTcp/wait_SdlSPISignal: Outgoing SIP TCP message to 10.10.10.94 on port 50376 index 1887
    [885429,NET]
    INVITE sip:[email protected]:50376;transport=tcp SIP/2.0
    Via: SIP/2.0/TCP 10.10.10.195:5060;branch=z9hG4bK231b78d1b56
    From: ;tag=192046~d8e94532-127d-4dca-bba0-64b1675da032-24378467
    To: "491" ;tag=F13CE94DE942C47680356A647DC7F916
    Date: Tue, 19 Feb 2013 21:24:59 GMT
    Call-ID: AE7045FFB2D8D9C28D54651473A14A5D41B5B93C
    Supported: timer,resource-priority,replaces
    Min-SE:  1800
    User-Agent: Cisco-CUCM8.6
    Allow: INVITE, OPTIONS, INFO, BYE, CANCEL, ACK, PRACK, UPDATE, REFER, SUBSCRIBE, NOTIFY
    CSeq: 101 INVITE
    Max-Forwards: 70
    Expires: 180
    Allow-Events: presence
    Remote-Party-ID: "Leslie2" ;party=calling;screen=no;privacy=off
    Contact:
    Content-Type: application/sdp
    Content-Length: 237
    v=0
    o=CiscoSystemsCCM-SIP 192046 1 IN IP4 10.10.10.195
    s=SIP Call
    c=IN IP4 10.10.10.195----------------------------------------MTP
    b=TIAS:64000
    b=AS:64
    t=0 0
    m=audio 25030 RTP/AVP 0 101
    a=rtpmap:0 PCMU/8000
    a=ptime:20
    a=rtpmap:101 telephone-event/8000
    a=fmtp:101 0-15
    Wao! That was a long one isnt it...It was fun too.
    So now you can look at your sip phones and see if they can accept two inactive sdp messages within the same call. That way you can remove MTP. otherwise you will have MTP involved in every single call involving a sip phone, even if they do not involve transfers
    Please rate all useful posts
    "opportunity is a haughty goddess who waste no time with those who are unprepared"

  • SPA3102: Can I route a POTS line to a SIP phone?

    I need to temporarily get POTS service where there is, well, nothing. My idea is to use an SPA3102, a wireless link and a SIP phone (all of which I have) to solve the problem. At the required phone location, I would just have a SIP phone connected to a WiFi link.
    At the other end of the link would be the SPA3102. It's only connections would be to the WiFi link radio and the POTS line. No internet involved.
    First question: Can I do this? If yes, second is how as in how do I configure the SPA3102? If would be great if picking up the SIP phone got POTS dialtone but not mandatory. But, it clearly is mandatory that an incoming POTS call would ring the SIP phone.

    There is no network beyond the pieces I listed. The two ends look like this:
    Local: POTS line, SPA3102, wireless link radio
    Remote: wireless link radio, SIP phone
    The radio link is point-to-point and effectively can be ignored for the configuration. That is, a POTS line, SPA3102 and SIP phone hooked together would look effectively the same and this is how I will test the system before deployment.
    As there is no external/internet connection, the IP addresses are arbitrary. Clearly, adding a computer with web browser to the system for configuration purposes is needed but, once again, the IP address is arbitrary. My guess (and it is just that) is that the computer can be plugged into the Ethernet port and the SIP side into the Internet port so no Ethernet hub would be needed but that is a guess.

  • German menu language on 7960G SIP Phone

    Hi All
    I have flashed a 7960G SCCP Phone to SIP Firmware.
    Is there any possibility to give this phone another menu language, like german?
    Or is this running only on SCCP Firmware?
    Thank you

    Hi,
    thank you for the help.
    Now I have these files in my TFTP Server.
    These are my files:
    OS79XX.TXT
    P0S3-08-12-00
    SEP0014A8924D6D.CNF.XML
    <device>
    <devicePool>
    <callManagerGroup>
    <members>
    <member priority="0">
    <callManager>
    <ports>
    <ethernetPhonePort>2000</ethernetPhonePort>
    </ports>
    <processNodeName> </processNodeName>
    </callManager>
    </member>
    </members>
    </callManagerGroup>
    </devicePool>
    <versionStamp>{Jan 01 2005 00:00:00}</versionStamp>
    <loadInformation>P0S3-08-12-00</loadInformation>
    <userLocale>
    <name>German_Germany</name>
    <langCode>de</langCode>
    </userLocale>
    <networkLocale>Germany</networkLocale>
    <idleTimeout>0</idleTimeout>
    <authenticationURL></authenticationURL>
    <directoryURL></directoryURL>
    <idleURL></idleURL>
    <informationURL></informationURL>
    <messagesURL></messagesURL>
    <proxyServerURL></proxyServerURL>
    <servicesURL></servicesURL>
    </device>
    SIP0014A8924D6D.cnf
    # SIP Configuration Generic File
    # Line 1 appearance
    line1_name: 01010101001
    # Line 1 Registration Authentication
    line1_authname: "UNPROVISIONED"
    # Line 1 Registration Password
    line1_password: "UNPROVISIONED"
    # Line 2 appearance
    line2_name: football
    # Line 2 Registration Authentication
    line2_authname: "UNPROVISIONED"
    # Line 2 Registration Password
    line2_password: "UNPROVISIONED"
    ####### New Parameters added in Release 2.0 #######
    # All user_parameters have been removed
    # Phone Label (Text desired to be displayed in upper right corner)
    phone_label: "" ; Has no effect on SIP messaging
    # Line 1 Display Name (Display name to use for SIP messaging)
    line1_displayname: "User ID"
    # Line 2 Display Name (Display name to use for SIP messaging)
    line2_displayname: ""
    ####### New Parameters added in Release 3.0 ######
    # Phone Prompt (The prompt that will be displayed on console and telnet)
    phone_prompt: "SIP Phone" ; Limited to 15 characters (Default - SIP Phone)
    # Phone Password (Password to be used for console or telnet login)
    phone_password: "cisco" ; Limited to 31 characters (Default - cisco)
    # User classifcation used when Registering [ none(default), phone, ip ]
    user_info: none
    SIPDefault.cnf
    # SIP Default Generic Configuration File
    # Image Version
    image_version: P0S381200
    language: german
    # Proxy Server
    proxy1_address: "" ; Can be dotted IP or FQDN
    proxy2_address: "" ; Can be dotted IP or FQDN
    proxy3_address: "" ; Can be dotted IP or FQDN
    proxy4_address: "" ; Can be dotted IP or FQDN
    proxy5_address: "" ; Can be dotted IP or FQDN
    proxy6_address: "" ; Can be dotted IP or FQDN
    # Proxy Server Port (default - 5060)
    proxy1_port: 5060
    proxy2_port: 5060
    proxy3_port: 5060
    proxy4_port: 5060
    proxy5_port: 5060
    proxy6_port: 5060
    # Proxy Registration (0-disable (default), 1-enable)
    proxy_register: 0
    # Phone Registration Expiration [1-3932100 sec] (Default - 3600)
    timer_register_expires: 3600
    # Codec for media stream (g711ulaw (default), g711alaw, g729a)
    preferred_codec: g711ulaw
    # TOS bits in media stream [0-5] (Default - 5)
    tos_media: 5
    # Inband DTMF Settings (0-disable, 1-enable (default))
    dtmf_inband: 1
    # Out of band DTMF Settings (none-disable, avt-avt enable (default), avt_always - always avt )
    dtmf_outofband: avt
    # DTMF dB Level Settings (1-6dB down, 2-3db down, 3-nominal (default), 4-3db up, 5-6dB up)
    dtmf_db_level: 3
    # SIP Timers
    timer_t1: 500 ; Default 500 msec
    timer_t2: 4000 ; Default 4 sec
    sip_retx: 10 ; Default 10
    sip_invite_retx: 6 ; Default 6
    timer_invite_expires: 180 ; Default 180 sec
    ####### New Parameters added in Release 2.0 #######
    # Dialplan template (.xml format file relative to the TFTP root directory)
    dial_template: dialplan
    # TFTP Phone Specific Configuration File Directory
    tftp_cfg_dir: "" ; Example: ./sip_phone/
    # Time Server (There are multiple values and configurations refer to Admin Guide for Specifics)
    sntp_server: "" ; SNTP Server IP Address
    sntp_mode: directedbroadcast ; unicast, multicast, anycast, or directedbroadcast (default)
    time_zone: EST ; Time Zone Phone is in
    dst_offset: 1 ; Offset from Phone's time when DST is in effect
    dst_start_month: April ; Month in which DST starts
    dst_start_day: "" ; Day of month in which DST starts
    dst_start_day_of_week: Sun ; Day of week in which DST starts
    dst_start_week_of_month: 1 ; Week of month in which DST starts
    dst_start_time: 02 ; Time of day in which DST starts
    dst_stop_month: Oct ; Month in which DST stops
    dst_stop_day: "" ; Day of month in which DST stops
    dst_stop_day_of_week: Sunday ; Day of week in which DST stops
    dst_stop_week_of_month: 8 ; Week of month in which DST stops 8=last week of month
    dst_stop_time: 2 ; Time of day in which DST stops
    dst_auto_adjust: 1 ; Enable(1-Default)/Disable(0) DST automatic adjustment
    time_format_24hr: 1 ; Enable(1 - 24Hr Default)/Disable(0 - 12Hr)
    # Do Not Disturb Control (0-off, 1-on, 2-off with no user control, 3-on with no user control)
    dnd_control: 0 ; Default 0 (Do Not Disturb feature is off)
    # Caller ID Blocking (0-disbaled, 1-enabled, 2-disabled no user control, 3-enabled no user control)
    callerid_blocking: 0 ; Default 0 (Disable sending all calls as anonymous)
    # Anonymous Call Blocking (0-disabled, 1-enabled, 2-disabled no user control, 3-enabled no user control)
    anonymous_call_block: 0 ; Default 0 (Disable blocking of anonymous calls)
    # DTMF AVT Payload (Dynamic payload range for AVT tones - 96-127)
    dtmf_avt_payload: 101 ; Default 101
    # Sync value of the phone used for remote reset
    sync: 1 ; Default 1
    ####### New Parameters added in Release 2.1 #######
    # Backup Proxy Support
    proxy_backup: "" ; Dotted IP of Backup Proxy
    proxy_backup_port: 5060 ; Backup Proxy port (default is 5060)
    # Emergency Proxy Support
    proxy_emergency: "" ; Dotted IP of Emergency Proxy
    proxy_emergency_port: 5060 ; Emergency Proxy port (default is 5060)
    # Configurable VAD option
    enable_vad: 0 ; VAD setting 0-disable (Default), 1-enable
    ####### New Parameters added in Release 2.2 ######
    # NAT/Firewall Traversal
    nat_enable: 0 ; 0-Disabled (default), 1-Enabled
    nat_address: "" ; WAN IP address of NAT box (dotted IP or DNS A record only)
    voip_control_port: 5060 ; UDP port used for SIP messages (default - 5060)
    start_media_port: 16384 ; Start RTP range for media (default - 16384)
    end_media_port: 32766 ; End RTP range for media (default - 32766)
    nat_received_processing: 0 ; 0-Disabled (default), 1-Enabled
    # Outbound Proxy Support
    outbound_proxy: "" ; restricted to dotted IP or DNS A record only
    outbound_proxy_port: 5060 ; default is 5060
    ####### New Parameter added in Release 3.0 #######
    # Allow for the bridge on a 3way call to join remaining parties upon hangup
    cnf_join_enable : 1 ; 0-Disabled, 1-Enabled (default)
    ####### New Parameters added in Release 3.1 #######
    # Allow Transfer to be completed while target phone is still ringing
    semi_attended_transfer: 1 ; 0-Disabled, 1-Enabled (default)
    # Telnet Level (enable or disable the ability to telnet into the phone)
    telnet_level: 1 ; 0-Disabled (default), 1-Enabled, 2-Privileged
    ####### New Parameters added in Release 4.0 #######
    # XML URLs
    services_url: "" ; URL for external Phone Services
    directory_url: "" ; URL for external Directory location
    logo_url: "" ; URL for branding logo to be used on phone display
    # HTTP Proxy Support
    http_proxy_addr: "" ; Address of HTTP Proxy server
    http_proxy_port: 80 ; Port of HTTP Proxy Server (80-default)
    # Dynamic DNS/TFTP Support
    dyn_dns_addr_1: "" ; restricted to dotted IP
    dyn_dns_addr_2: "" ; restricted to dotted IP
    dyn_tftp_addr: "" ; restricted to dotted IP
    # Remote Party ID
    remote_party_id: 0 ; 0-Disabled (default), 1-Enabled
    ####### New Parameters added in Release 4.4 #######
    # Call Hold Ringback (0-off, 1-on, 2-off with no user control, 3-on with no user control)
    call_hold_ringback: 0 ; Default 0 (Call Hold Ringback feature is off)
    ####### New Parameters added in Release 6.0 #######
    # Dialtone Stutter for MWI
    stutter_msg_waiting: 0 ; 0-Disabled (default), 1-Enabled
    # RTP Call Statistics (SIP BYE/200 OK message exchange)
    call_stats: 0 ; 0-Disabled (default), 1-Enabled
    xmlDefault.CNF.XML
    <?xml version="1.0"?>
    -<Default>
    -<callManagerGroup>
    -<members>
    -<member priority="0">
    -<callManager>
    -<ports>
    <ethernetPhonePort>2000</ethernetPhonePort>
    </ports>
    <processNodeName/>
    </callManager>
    </member>
    </members>
    <loadInformation6 model="IP Phone 7910"/>
    <loadInformation124 model="Addon 7914"/>
    <loadInformation9 model="IP Phone 7935"/>
    <loadInformation8 model="IP Phone 7940"/>
    <loadInformation7 model="IP Phone 7960">P0S3-8-12-00</loadInformation7>
    <loadInformation20000 model="IP Phone 7905"/>
    <loadInformation30008 model="IP Phone 7902"/>
    <loadInformation30002 model="IP Phone 7920"/>
    <loadInformation30019 model="IP Phone 7936"/>
    <loadInformation30006 model="IP Phone 7970"/>
    <loadInformation30018 model="IP Phone 7961"/>
    <loadInformation30007 model="IP Phone 7912"/>
    </callManagerGroup>
    </Default>
    The folders "German_Germany"; "germany" and the file German_Germany.aar are in TFTP folder,too. But my phone is doing nothing with this files.
    This is the log of TFTP Server:
    Rcvd DHCP inform Msg for IP 192.168.0.9, Mac 02:70:7E:7F:09:01 [04/03 13:21:54.559]
    Rcvd DHCP inform Msg for IP 192.168.0.9, Mac 02:70:7E:7F:09:01 [04/03 13:21:58.562]
    Rcvd DHCP Rqst Msg for IP 0.0.0.0, Mac 00:14:A8:92:4D:6D [04/03 13:22:45.892]
    Previously allocated address 192.168.0.6 acked [04/03 13:22:45.893]
    Connection received from 192.168.0.6 on port 50798 [04/03 13:22:46.037]
    Read request for file <CTLSEP0014A8924D6D.tlv>. Mode octet [04/03 13:22:46.038]
    File <CTLSEP0014A8924D6D.tlv> : error 2 in system call CreateFile Das System kann die angegebene Datei nicht finden. [04/03 13:22:46.038]
    Connection received from 192.168.0.6 on port 50798 [04/03 13:22:47.036]
    Read request for file <CTLSEP0014A8924D6D.tlv>. Mode octet [04/03 13:22:47.036]
    File <CTLSEP0014A8924D6D.tlv> : error 2 in system call CreateFile Das System kann die angegebene Datei nicht finden. [04/03 13:22:47.036]
    Connection received from 192.168.0.6 on port 50798 [04/03 13:22:51.035]
    Read request for file <CTLSEP0014A8924D6D.tlv>. Mode octet [04/03 13:22:51.036]
    File <CTLSEP0014A8924D6D.tlv> : error 2 in system call CreateFile Das System kann die angegebene Datei nicht finden. [04/03 13:22:51.036]
    Connection received from 192.168.0.6 on port 50799 [04/03 13:22:51.056]
    Read request for file <SEP0014A8924D6D.cnf.xml>. Mode octet [04/03 13:22:51.057]
    File <SEP0014A8924D6D.cnf.xml> : error 2 in system call CreateFile Das System kann die angegebene Datei nicht finden. [04/03 13:22:51.057]
    Connection received from 192.168.0.6 on port 50800 [04/03 13:22:51.085]
    Read request for file <SIP0014A8924D6D.cnf>. Mode octet [04/03 13:22:51.086]
    File <SIP0014A8924D6D.cnf> : error 2 in system call CreateFile Das System kann die angegebene Datei nicht finden. [04/03 13:22:51.086]
    Connection received from 192.168.0.6 on port 50801 [04/03 13:22:51.105]
    Read request for file <MGC0014A8924D6D.cnf>. Mode octet [04/03 13:22:51.105]
    File <MGC0014A8924D6D.cnf> : error 2 in system call CreateFile Das System kann die angegebene Datei nicht finden. [04/03 13:22:51.105]
    Connection received from 192.168.0.6 on port 50802 [04/03 13:22:51.124]
    Read request for file <XMLDefault.cnf.xml>. Mode octet [04/03 13:22:51.127]
    Using local port 65426 [04/03 13:22:51.127]
    <XMLDefault.cnf.xml>: sent 3 blks, 1077 bytes in 0 s. 0 blk resent [04/03 13:22:51.135]
    Connection received from 192.168.0.6 on port 50803 [04/03 13:22:51.180]
    Read request for file <P0S3-8-12-00.loads>. Mode octet [04/03 13:22:51.180]
    Using local port 65427 [04/03 13:22:51.180]
    <P0S3-8-12-00.loads>: sent 1 blk, 458 bytes in 0 s. 0 blk resent [04/03 13:22:51.183]
    Rcvd DHCP inform Msg for IP 192.168.0.9, Mac 02:70:7E:7F:09:01 [04/03 13:24:17.151]
    Rcvd DHCP inform Msg for IP 192.168.0.9, Mac 02:70:7E:7F:09:01 [04/03 13:24:20.150]
    Rcvd DHCP Rqst Msg for IP 0.0.0.0, Mac 00:14:A8:92:4D:6D [04/03 13:24:34.219]
    Previously allocated address 192.168.0.6 acked [04/03 13:24:34.220]
    Connection received from 192.168.0.6 on port 50823 [04/03 13:24:34.258]
    Read request for file <SIPDefault.cnf>. Mode octet [04/03 13:24:34.259]
    Using local port 64133 [04/03 13:24:34.259]
    Connection received from 192.168.0.6 on port 50823 [04/03 13:24:35.250]
    Read request for file <SIPDefault.cnf>. Mode octet [04/03 13:24:35.250]
    Using local port 64134 [04/03 13:24:35.250]
    Connection received from 192.168.0.6 on port 50823 [04/03 13:24:39.250]
    Read request for file <SIPDefault.cnf>. Mode octet [04/03 13:24:39.250]
    Using local port 64135 [04/03 13:24:39.250]
    <SIPDefault.cnf>: sent 13 blks, 6203 bytes in 0 s. 0 blk resent [04/03 13:24:39.284]
    Connection received from 192.168.0.6 on port 50824 [04/03 13:24:39.485]
    Read request for file <SIP0014A8924D6D.cnf>. Mode octet [04/03 13:24:39.485]
    File <SIP0014A8924D6D.cnf> : error 2 in system call CreateFile Das System kann die angegebene Datei nicht finden. [04/03 13:24:39.485]
    TIMEOUT waiting for Ack block #1 [04/03 13:24:49.260]
    TIMEOUT waiting for Ack block #1 [04/03 13:24:50.251]
    Rcvd DHCP Rqst Msg for IP 0.0.0.0, Mac 00:14:A8:92:4D:6D [04/03 13:26:50.610]
    Previously allocated address 192.168.0.6 acked [04/03 13:26:50.611]
    Connection received from 192.168.0.6 on port 50857 [04/03 13:26:50.649]
    Read request for file <SIPDefault.cnf>. Mode octet [04/03 13:26:50.649]
    Using local port 64137 [04/03 13:26:50.649]
    Connection received from 192.168.0.6 on port 50857 [04/03 13:26:51.641]
    Read request for file <SIPDefault.cnf>. Mode octet [04/03 13:26:51.642]
    Using local port 64138 [04/03 13:26:51.642]
    Connection received from 192.168.0.6 on port 50857 [04/03 13:26:55.641]
    Read request for file <SIPDefault.cnf>. Mode octet [04/03 13:26:55.641]
    Using local port 64139 [04/03 13:26:55.642]
    <SIPDefault.cnf>: sent 13 blks, 6203 bytes in 0 s. 0 blk resent [04/03 13:26:55.676]
    Connection received from 192.168.0.6 on port 50858 [04/03 13:26:55.874]
    Read request for file <SIP0014A8924D6D.cnf>. Mode octet [04/03 13:26:55.875]
    File <SIP0014A8924D6D.cnf> : error 2 in system call CreateFile Das System kann die angegebene Datei nicht finden. [04/03 13:26:55.875]
    TIMEOUT waiting for Ack block #1 [04/03 13:27:05.651]
    TIMEOUT waiting for Ack block #1 [04/03 13:27:06.645]
    Rcvd DHCP Rqst Msg for IP 0.0.0.0, Mac 00:14:A8:92:4D:6D [04/03 13:28:40.670]
    Previously allocated address 192.168.0.6 acked [04/03 13:28:40.671]
    Connection received from 192.168.0.6 on port 50797 [04/03 13:28:40.813]
    Read request for file <CTLSEP0014A8924D6D.tlv>. Mode octet [04/03 13:28:40.813]
    File <CTLSEP0014A8924D6D.tlv> : error 2 in system call CreateFile Das System kann die angegebene Datei nicht finden. [04/03 13:28:40.814]
    Connection received from 192.168.0.6 on port 50797 [04/03 13:28:41.803]
    Read request for file <CTLSEP0014A8924D6D.tlv>. Mode octet [04/03 13:28:41.804]
    File <CTLSEP0014A8924D6D.tlv> : error 2 in system call CreateFile Das System kann die angegebene Datei nicht finden. [04/03 13:28:41.804]
    Connection received from 192.168.0.6 on port 50797 [04/03 13:28:45.803]
    Read request for file <CTLSEP0014A8924D6D.tlv>. Mode octet [04/03 13:28:45.803]
    File <CTLSEP0014A8924D6D.tlv> : error 2 in system call CreateFile Das System kann die angegebene Datei nicht finden. [04/03 13:28:45.804]
    Connection received from 192.168.0.6 on port 50798 [04/03 13:28:45.824]
    Read request for file <SEP0014A8924D6D.cnf.xml>. Mode octet [04/03 13:28:45.824]
    File <SEP0014A8924D6D.cnf.xml> : error 2 in system call CreateFile Das System kann die angegebene Datei nicht finden. [04/03 13:28:45.824]
    Connection received from 192.168.0.6 on port 50799 [04/03 13:28:45.853]
    Read request for file <SIP0014A8924D6D.cnf>. Mode octet [04/03 13:28:45.853]
    File <SIP0014A8924D6D.cnf> : error 2 in system call CreateFile Das System kann die angegebene Datei nicht finden. [04/03 13:28:45.853]
    Connection received from 192.168.0.6 on port 50800 [04/03 13:28:45.874]
    Read request for file <MGC0014A8924D6D.cnf>. Mode octet [04/03 13:28:45.876]
    File <MGC0014A8924D6D.cnf> : error 2 in system call CreateFile Das System kann die angegebene Datei nicht finden. [04/03 13:28:45.876]
    Connection received from 192.168.0.6 on port 50801 [04/03 13:28:45.895]
    Read request for file <XMLDefault.cnf.xml>. Mode octet [04/03 13:28:45.895]
    Using local port 64147 [04/03 13:28:45.895]
    <XMLDefault.cnf.xml>: sent 3 blks, 1077 bytes in 0 s. 0 blk resent [04/03 13:28:45.898]
    Connection received from 192.168.0.6 on port 50802 [04/03 13:28:45.935]
    Read request for file <P0S3-8-12-00.loads>. Mode octet [04/03 13:28:45.936]
    Using local port 64148 [04/03 13:28:45.936]
    <P0S3-8-12-00.loads>: sent 1 blk, 458 bytes in 0 s. 0 blk resent [04/03 13:28:45.937]
    Rcvd DHCP Rqst Msg for IP 0.0.0.0, Mac 00:14:A8:92:4D:6D [04/03 13:30:28.597]
    Previously allocated address 192.168.0.6 acked [04/03 13:30:28.597]
    Connection received from 192.168.0.6 on port 50787 [04/03 13:30:28.636]
    Read request for file <SIPDefault.cnf>. Mode octet [04/03 13:30:28.636]
    Using local port 64149 [04/03 13:30:28.636]
    Connection received from 192.168.0.6 on port 50787 [04/03 13:30:29.627]
    Read request for file <SIPDefault.cnf>. Mode octet [04/03 13:30:29.628]
    Using local port 64150 [04/03 13:30:29.628]
    Connection received from 192.168.0.6 on port 50787 [04/03 13:30:33.627]
    Read request for file <SIPDefault.cnf>. Mode octet [04/03 13:30:33.628]
    Using local port 64151 [04/03 13:30:33.628]
    <SIPDefault.cnf>: sent 13 blks, 6203 bytes in 0 s. 0 blk resent [04/03 13:30:33.658]
    Connection received from 192.168.0.6 on port 50788 [04/03 13:30:33.856]
    Read request for file <SIP0014A8924D6D.cnf>. Mode octet [04/03 13:30:33.856]
    File <SIP0014A8924D6D.cnf> : error 2 in system call CreateFile Das System kann die angegebene Datei nicht finden. [04/03 13:30:33.857]
    Rcvd DHCP inform Msg for IP 192.168.0.9, Mac 02:70:7E:7F:09:01 [04/03 13:30:41.756]
    TIMEOUT waiting for Ack block #1 [04/03 13:30:43.637]
    TIMEOUT waiting for Ack block #1 [04/03 13:30:44.629]
    Rcvd DHCP inform Msg for IP 192.168.0.9, Mac 02:70:7E:7F:09:01 [04/03 13:30:44.759]
    Rcvd DHCP inform Msg for IP 192.168.0.9, Mac 02:70:7E:7F:09:01 [04/03 13:32:11.253]
    Rcvd DHCP inform Msg for IP 192.168.0.9, Mac 02:70:7E:7F:09:01 [04/03 13:32:14.253]
    Rcvd DHCP Rqst Msg for IP 0.0.0.0, Mac 00:14:A8:92:4D:6D [04/03 13:33:50.655]
    Previously allocated address 192.168.0.6 acked [04/03 13:33:50.656]
    Connection received from 192.168.0.6 on port 50795 [04/03 13:33:50.696]
    Read request for file <SIPDefault.cnf>. Mode octet [04/03 13:33:50.696]
    Using local port 62124 [04/03 13:33:50.696]
    Connection received from 192.168.0.6 on port 50795 [04/03 13:33:51.685]
    Read request for file <SIPDefault.cnf>. Mode octet [04/03 13:33:51.686]
    Using local port 62125 [04/03 13:33:51.686]
    Connection received from 192.168.0.6 on port 50795 [04/03 13:33:55.685]
    Read request for file <SIPDefault.cnf>. Mode octet [04/03 13:33:55.685]
    Using local port 62126 [04/03 13:33:55.685]
    <SIPDefault.cnf>: sent 13 blks, 6203 bytes in 0 s. 0 blk resent [04/03 13:33:55.723]
    Connection received from 192.168.0.6 on port 50796 [04/03 13:33:55.915]
    Read request for file <SIP0014A8924D6D.cnf>. Mode octet [04/03 13:33:55.915]
    File <SIP0014A8924D6D.cnf> : error 2 in system call CreateFile Das System kann die angegebene Datei nicht finden. [04/03 13:33:55.915]
    TIMEOUT waiting for Ack block #1 [04/03 13:34:05.698]
    TIMEOUT waiting for Ack block #1 [04/03 13:34:06.691]
    Is there anybody, who can help me with this problem.

  • CME SIP Phone Calls in one-way (inside local network)

    Hello everyone, first time here, need a little help.
    I'm having some trouble to find a solution to the following problem.
    Recently I've installed CME 9.1 using the router 2921. Most of the phones are SIPs, model 3905 (around 20 of them), with the last firmware updated.
    Some users are complaining one way audio issue in internal calls, from a extension to another (only in sip phones)
    With Wireshark capture I could see that RTP packets are being sent and receive by the router and not directly trough the phones. Is this normal in CME? When a call with problems occours (one way audio) there is no audio in one way, but router still sends confort noise packets.
    Here is my config.
    Thanks for any help.
    Martin
    ##################################################################################33
    System returned to ROM by power-on
    System restarted at 11:29:23 BR Tue Jan 29 2013
    System image file is "flash0:c2900-universalk9-mz.SPA.152-4.M2.bin"
    Last reload type: Normal Reload
    Last reload reason: power-on
    voice service voip
    no ip address trusted authenticate
    allow-connections h323 to h323
    allow-connections h323 to sip
    allow-connections sip to h323
    allow-connections sip to sip
    fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none
    sip
      registrar server expires max 3600 min 120
    voice register global
    mode cme
    source-address 10.3.245.1 port 5060
    max-dn 60
    max-pool 70
    load ATA-187 ATA187.9-2-3-1
    load 3905 CP3905.9-2-1-0
    authenticate realm all
    timezone 17
    time-format 24
    date-format D/M/Y
    tftp-path flash:
    file text
    create profile sync 0094230880392697
    network-locale U1
    user-locale U1 load /CME-locale-pt_BR-Portuguese-8.8.2.5.tar
    ntp-server 10.3.244.7 mode directedbroadcast
    voice register dn  1
    number 9006
    name Sala_Reuniao_02
    label Sala de Reuniao 2
    voice register dn  2
    number 9007
    name Sala_Reuniao_03
    voice register dn  3
    number 9008
    name Sala Reuniao 04
    voice register pool  1
    id mac 8478.ACE6.09A2
    type 3905
    number 1 dn 1
    template 1
    codec g711ulaw
    voice register pool  2
    id mac 8478.ACE6.0573
    type 3905
    number 1 dn 2
    codec g711ulaw
    voice register pool  3
    id mac 5897.1ECD.8F8D
    type 3905
    number 1 dn 3
    codec g711ulaw
    interface GigabitEthernet0/0
    no ip address
    duplex auto
    speed auto
    interface GigabitEthernet0/0.220
    encapsulation dot1Q 220
    ip address 10.3.245.1 255.255.255.0
    ip helper-address 10.3.244.71
    h323-gateway voip bind srcaddr 10.3.245.1
    telephony-service
    max-ephones 5
    max-dn 5 no-reg both
    ip source-address 10.3.245.1 port 2000
    timeouts interdigit 5
    timeouts busy 12
    system message  XXXXXXXX
    cnf-file location flash:
    cnf-file perphone
    user-locale U2 load CME-locale-pt_BR-Portuguese-8.8.2.5.tar
    user-locale 2 PT
    network-locale U2
    load 7925 CP7925G-1.4.1SR1.LOADS
    load 6941 SCCP69xx.9-2-1-0.loads
    time-zone 17
    time-format 24
    date-format dd-mm-yy
    max-conferences 8 gain -6
    dn-webedit
    time-webedit
    transfer-system full-consult
    transfer-pattern .T
    create cnf-files version-stamp Jan 01 2002 00:00:00
    ephone-dn  1  dual-line
    number 9001
    ephone  1
    mac-address D867.D9E6.F57F
    ephone-template 1
    type 6941
    button  1:1

    Hi ,
    We have upgarded the the firmware to the  3905.9-2-2ES2 , but show voice register pool phone-load still shows the old firmware, but the phoen itself is showing the new upgraded version on the dsiplay ...any advice is highly appricated,
    ADM-CME9#show voice register pool phone-load
    Pool Device Name     Current-Version             Previous-Version
    ==== =============== =========================== ===========================
    1    SEP7081053DE72F Cisco/SPA502G-7.4.8a                                  
    3    SEP34BDC8C6C412 Cisco-CP3905/9.2.1                                    
    4    SEP34BDC8C64561 Cisco-CP3905/9.2.1                                    
    5    SEP54781AE1F531 Cisco-CP3905/9.2.1                                    
    6    SEP54781AE171D2 Cisco-CP3905/9.2.1                                    
    10   SEP54781AE1F544 Cisco-CP3905/9.2.1                                    
    15   SEP1CE6C77323CD Cisco-CP3905/9.2.1                                    
    16   SEP58971E282A23 Cisco-CP3905/9.2.1                                    
    17   SEP58971E2822A8 Cisco-CP3905/9.2.1                                    
    19   SEP1CE6C77321F3 Cisco-CP3905/9.2.1                                    
    30   SEP54781AE171E2 Cisco-CP3905/9.2.1                                    
    31   SEP54781AE16FD4 Cisco-CP3905/9.2.1                                    
    32   SEP54781AE16F2F Cisco-CP3905/9.2.1                                    
    33   SEP54781A1C77FD Cisco-CP3905/9.2.1                                    
    34   SEP54781A1C77DC Cisco-CP3905/9.2.1                                    
    35   SEP54781AE17527 Cisco-CP3905/9.2.1                                    
    36   SEP54781AE17766 Cisco-CP3905/9.2.1                                    
    37   SEP54781AE1731A Cisco-CP3905/9.2.1                                    
    38   SEP54781AE08B8D Cisco-CP3905/9.2.1                                    
    39   SEP54781AE123B1 Cisco-CP3905/9.2.1                                    

  • Incoming calls issue in Third Party SIP Phone

    Hi,
    Yesterday I configured my third party sip phone which is yealink in this case on cucm and successfully registered it with cucm, despite of registration i have some calling issue in this phone. I am able to make outbound calls from this phone to any other phone however issue is related to inbound calls.I tried calling its DN from anywhere but call disconnect after sometime. Also didnt get any proper sip session trace in RTMT. Kindly suggest some step to sortout this issue.
    Thanks

    Dear Manish,
    Call normally dicsonnected after 30-40 sec with termination code 102 in session trace. PFB SDI  trace with 5030 is Thirdparty sip phone and 5033 is c7945. Looking forward for your suggestion.
    CallingPartyNumber=5033
    |DialingPartition=
    |DialingPattern=5030
    |FullyQualifiedCalledPartyNumber=5030
    |DialingPatternRegularExpression=(5030)
    |DialingWhere=
    |PatternType=Enterprise
    |PotentialMatches=NoPotentialMatchesExist
    |DialingSdlProcessId=(0,0,0)
    |PretransformDigitString=5030
    |PretransformTagsList=SUBSCRIBER
    |PretransformPositionalMatchList=5030
    |CollectedDigits=5030
    |UnconsumedDigits=
    |TagsList=SUBSCRIBER
    |PositionalMatchList=5030
    |VoiceMailbox=
    |VoiceMailCallingSearchSpace=PT-LHR-LOCAL:PT-Local:Unityvmpt:PT-F6-Local:PT-ISL-LOCAL:PT-KHI-LOCAL:PT_Operator_LHR:PT_Operator_KHI:PT_Operator_ISL
    |VoiceMailPilotNumber=7103
    |RouteBlockFlag=RouteThisPattern
    |RouteBlockCause=0
    |AlertingName=Syed Ahmer
    |UnicodeDisplayName=Syed Ahmer
    |DisplayNameLocale=1
    |OverlapSendingFlagEnabled=0
    12:17:38.028 |//SIP/SIPUdp/wait_SdlSPISignal: Outgoing SIP UDP message to 172.16.200.21:[5062]:
    [23928282,NET]
    INVITE sip:[email protected]:5062 SIP/2.0
    Via: SIP/2.0/UDP 10.100.200.11:5060;branch=z9hG4bK1ca0cc6e317649
    From: "Syed Ahmer" ;tag=8787406~039e2a80-8561-4586-8954-d01ed2aa12c8-246211918
    To:
    Date: Thu, 30 Jan 2014 07:17:38 GMT
    Call-ID: [email protected]
    Supported: timer,resource-priority,replaces
    Min-SE:  1800
    User-Agent: Cisco-CUCM8.5
    Allow: INVITE, OPTIONS, INFO, BYE, CANCEL, ACK, PRACK, UPDATE, REFER, SUBSCRIBE, NOTIFY
    CSeq: 101 INVITE
    Expires: 180
    Allow-Events: presence
    Send-Info: conference, x-cisco-conference
    Alert-Info:
    Contact:
    Remote-Party-ID: "Syed Ahmer" ;party=calling;screen=yes;privacy=off
    Max-Forwards: 70
    Content-Length: 0
    |14,100,50,1.14103336^10.163.14.4^SEP00230432C828
    12:17:38.028 |EnvProcessUdpPort - EnvProcessUdpHandler::fireSignal() varId = 0|14,100,50,1.14103336^10.163.14.4^SEP00230432C828
    12:17:38.028 |EnvProcessUdpHandler::fireSignal - SEND: index = 0, handler = 0xaf299320|*^*^*
    12:17:38.028 |EnvProcessUdpPort::fireSignal - SEND, destination = 172.16.200.21:5062|*^*^*
    12:17:38.028 |EnvProcessUdpPort - EnvProcessUdpHandler::send(buff, 850, 172.16.200.21:5062)|*^*^*

Maybe you are looking for

  • Load Test Results - time series request data for by URL in VS2013

    I am trying to figure out how to export and then analyze the results of a load test, but after the test is over it seems I cannot find the data for each individual request by url. This data shows during the load test itself, but after it is over it s

  • DBMS_METADATA.get_ddl issues

    When you run, select dbms_metadata.get_ddl('USER', 'scott') FROM DUAL; gives following error... ORA-31603: object "scott" of type USER not found in schema "SYSTEM" ORA-06512: at "SYS.DBMS_SYS_ERROR", line 105 ORA-06512: at "SYS.DBMS_METADATA", line 2

  • Viewing PDF After Exporting from InDesign

    G'day from Australia. My name is Steve, I do a bit of freelance work from time to time but I'm also  employed by a Christian Minstry in Brisbane. Recently I have encountered (and not just me but my manager as well) that when creating a pdf from InDes

  • Detecting computer wake up from sleep

    Is there a way (i.e., event) in AIR to detect that a computer just woke up from sleep or hibernation?

  • Premiere Pro CS 5.5 Crashes right after being launched.

    So... I have a problem with my Premiere Pro. I'm not the most experienced person behind the keyboard so I thought that my best bet is to ask from the professionals. Anyway, when I launch my premiere pro, it starts like every Adobe program I have. The