A 'Do your own homework' page?

Hi,
I'm a frequent poster to the Java Forums, and I get a lot of enjoyment from helping people out; but there are two things that really get up my wrinkly old nose:
1. People who want a solution handed to them.
2. People who hand out "solutions" (presumably to prove how smart they are).
[url http://forums.oracle.com/forums/thread.jspa?messageID=9797998#9796263]I asked the moderators of our forums whether we could add something to the "etiquette" section of the FAQ page, and was shown these examples:
Darryl Burke wrote:
You mean, something on the lines of these pages?
http://www.coderanch.com/how-to/java/DoYourOwnHomework
http://www.coderanch.com/how-to/java/NotACodeMill
They also suggested that I should post a thread here.
Those pages look like a really good idea to me (in fact, JavaRanch has quite a network of them), and would give the old hands who feel the same way as I do something to refer to, rather than having to type out testy replies in longhand. My CTS is reasonably advanced as it is.
I'd be interested to know what you think.
Winston

sybrand_b wrote:
Yes, we have. But does anyone read it? Did it diminish the amount of FAQs?
Did it diminish the amount of people ignoring the 'How to post a tuning request' guideline?
You and I know the answerActually, we have no metrics. I really want to believe that some people actually look at and attempt to follow FAQ's, and others come around to it. It is hard to evaluate how much skew is from the clueless.
>
Do people provide completely working examples to RTFM questions, so encouraging them? Should I really mention Frank Kulash here?This is nothing new, but that does not at all mean we have to give up, nor does it mean we have to stress over it. Different idiots respond to different abuse, and some small percentage will never learn. The best we can hope for is group disapproval making most of the worst go away, and the variety of individual disapprovals will help in special cases.
This is not a homogenous population, and that is a good thing.

Similar Messages

I am having to use IE to access your site to send you a question about why Firefox is not loading even your own home page? Also can i go back to the previous version of Firefox, as this version (4.0) has a huge number of problems?

It started out as once in a while the page would load, but be blank. Now it is nearly every website I attempt to go shows it loads the page, as the address is listed in the top. it shows the page name in the tab, but the page is blank.
As I said in my question, I am having to contact you on IE, because Firefox won't load it's own pages.
So that you know, it had been years snce I used IE, Since loading 4.0 it has become a daily event.

You might try using the add-on 'NoSquint' which allows numerous zoom options specific to each page you visit & keeps your settings - https://addons.mozilla.org/en-US/firefox/addon/nosquint/
If you want to go back to 3.6x, you will find it here:
http://www.mozilla.com/en-US/firefox/all-older.html
In most cases you can simply "upgrade" (meaning downgrade) directly from the installation. It would be a good idea to save your passwords & bookmarks just to be on the safe side.

I want to ctrl-+, ctrl-+, ctrl-+, ctrl-+, ctrol-+ on every single web page.... even your own dumb web page.

Every page on the internet takes up 70% of my screen.
I want to use common sense and force every page to take up 100% of my screen.
I want to perform ctrl-+, ctrl-+, ctrl-+ ctrl-+, ctrl-+ on every single page... how can I do that?
WHere is the 100% option? This is rediculous - a web browser that insists on using 60% of the screen.
Even on your own web site - there is 1.5 inches on both sides of the page - how is this useful or logical or reasonable in any way?
TAKE THE WHOLE SCREEN.

My control key is wore out... literally. It's held together with glue and tape and honey. Because I have to hit ctrl-+ ctrl-+ ctrl-+ ctrl-+ ctrl-+ on every single web site.
Because there is no option - 100%, that's the deal. Make the stuff 100%. How hard can that possibly be?

Modify\Remove UDI 'build your own page' text

Hi ,
I am using UDI wizard to create custom 'Build your own page' type template. Could anyone pls. suggest how to modify\remove 'my First custom page'? from this wizard page?
any pointers will be appreciated. Thanks.

Hi,
It is not displayed when your run the UDI or when you run the Preview either actually.. The name used will be the two you supplied when creating the page here:
So the My First Custom page is just displayed when you edit it.
-- My System Center blog ccmexec.com -- Twitter
@ccmexec

Printing my own photos! Does anyone know what happened to the area on the left hand side of iPhoto when you went into printing your own photos? I used to be able to create a page of wallets and print it from my own computer and now I can't find it.Help

Does anyone know what happened to printing your own photos in iphoto? There used to be a thing on the left hand side of iphoto that you used to create wallets, 5x7, etc. Now there is nothing there. Can anyone help me? I dont want to order stuff, i want to pirint my own.

what version of iPhoto?
LN

Using SqlProvider and Weblogic authenticator in my own login page

Hi All,
I want to use SqlProvider of weblogic server for authentication of users. For the said purpose I have made necessary steps in weblogic server console. now i want to use it in my own login page and authenticate user based on sqlProvider and wls.
Can u suggest me what to do? or where do I move next ?

Add ADF Security to your application.
- Add the groups (the ones in your WLS) to 'Enterprise roles' (use the same name).
- Define your 'Application Roles' (the roles you want to use in your application) and add the corresponding Enterprise roles to it.
- Set the resource grants
That should be it.

Roll Your Own - APEX 4.0 and JQuery-UI Application

For those with a apex.oracle.com account and want to see jQeury tabs running via 4.0 in your own Workspace, use following this script to create your own version of Shijesh's (Apex_Noob) application.
Credit also goes out to Alistair Laing for his hard work in investigating why 4.0 is requiring the use of the googleapis jquery.js... libraries.
Application Builder - Create
Application Type - Database
Create Application - From Scratch
Name - jQuery Application
Add Page - keep default and Click Add Page
Click CreateMy application defaulted to Theme 2, you will need to switch the theme to one of the following: If you don't the tabs will not render properly.
8 Orange
10 Sand
13 Classic Blue
14 Simple Green
15 Light Blue
16 Dark Blue
18 Simple Gray
19 Red Gray
Message - Application created successfully.
Click Shared ComponentsUnder User Interface Click - ThemesIf you don't see one of the above Themes, you will need to Create and switch your Theme.
Click - CreateFrom the Repository selected Click - Next and select one of the above Themes
Click - Switch ThemeSelect one of the above Themes and Click - Next
Click -NextClick - Switch ThemeReturn to your newly created Application by Clicking on Application xxxxxxx Breadcrumb
Click - Create PageSelect - Blank PageClick - NextAssign the page a name
Click - NextAccept defaults and Click - NextClick - FinishClick - Edit PageI still work in Component View, to toggle to this View, click on the control adjacent to Page number and Go button. Hover over the ones on the far right and you will see both Component View and Tree View
From Component View
Click on the Page Edit Control
In the Text Area labeled Javascript/Execute when Page Loads - paste in the following code:
$x("tabs").appendChild( $x("tabs-1"));
$x("tabs").appendChild( $x("tabs-2"));
jQuery("#tabs").tabs();In the Text Area labeled HTML Header and Body Attribute/HTML Header - paste in the following code:
<link rel="stylesheet" href="http://ajax.googleapis.com/ajax/libs/jqueryui/1.8.1/themes/redmond/jquery-ui.css" type="text/css" />
<script src= "http://ajax.googleapis.com/ajax/libs/jqueryui/1.8.1/jquery-ui.js"> </script>Click - Apply ChangesRequired use of the Google jqueryui libraries is being questioned by recent threads created by Alistair Laing since it appears that 4.0 does not currently support jQeury tabs
{thread:id=1083507}
{thread:id=1083540}
Create a Region
Type HTML Text - accept defaults
Provide a Title like "Tabs" and accept defaults
Template - Reports Region
Sequence 10
Click - NextIn the Enter HTML Text Region Source: Text Area - paste in the following code:
<div id="tabs">
<ul>
<li><a href="#tabs-1">Employees</a></li>
<li><a href="#tabs-2">Departments</a></li>
</ul>
</div>Click - Create RegionCreate a second Region
Type Report/Sql Report
Provide a Title like "Employees" and accept defaults
Template Reports Region
Sequence 20
Click - NextIn the Enter SQL Query or PL/SQL function returning a SQL Query: Text Area - paste in the following code:
SELECT empno,
       ename,
       job,
       mgr,
       hiredate,
       sal,
       comm,
       deptno
FROM   empClick - Create RegionEdit the newly created Report Region
Under Attributes/Static ID - paste in the following code:
tabs-1Click - Apply ChangesCreate a third Region
Type Report/Sql Report
Provide a Title like "Departments" and accept defaults
Template Reports Region
Sequence 30
Click - NextIn the Enter SQL Query or PL/SQL function returning a SQL Query: Text Area - paste in the following code:
SELECT deptno,
       dname,
       loc
FROM   deptClick - Create RegionEdit the newly created Report Region
Under Attributes/Static ID - paste in the following code:
tabs-2Click - Apply ChangesRun you page and you should see you tabs.
Jeff

Great post Jeff,
With regard to Jquery UI and tabs I've contacted the Apex dev team and received a reply from them.
All the jQueryUI files are included in the APEX 4.0 distribution, but not all jQueryUI components
are loaded by default to avoid a huge initial download. It's not necessary to load your own version of jQueryUI, just load the missing component.
For the "Tabs" you have to add
<link href="IMAGE_PREFIX#libraries/jquery-ui/1.8/themes/base/jquery.ui.tabs.css" rel="stylesheet" type="text/css" />
<script src="#IMAGE_PREFIX#libraries/jquery-ui/1.8/ui/minified/jquery.ui.tabs.min.js" type="text/javascript"></script>
to your page template or the header attribute of your page where you want to use it.They did not mention which other Jquery UI widgets were not included so people need to check to see if they get any JS errors Like "$('#tabs').tabs() is not a function" this would suggest that tabs is not being loaded. To included it in you page header directly after #HEAD# you need to place the css and js as stated above.
If you need jquery help just post you queries here or the is some other jquery links that maybe of some use
jQuery
http://jquery.com/ - Official jQuery Website
http://api.jquery.com/ - jQuery API Library
http://plugins.jquery.com/ - jQuery Plugins (Not APEX related)|
http://yayquery.com/ - yayQuery - jQuery Podcast
http://jqueryui.com/ - Official jQuery UI Website
http://jqueryui.com/demos/ - jQuery UI Demos
Edited by: Alistair Laing on Jun 9, 2010 4:04 PM
Add more links
Edited by: Alistair Laing on Jun 9, 2010 4:09 PM

How can you add your own print and export buttons to the CR viewer toolbar?

I posted a previous question that was asking how to get around the Information Bar in IE7 when you export and print. Unfortunately the CR viewer file download code gets blocked by IE7 because the buttons don't directly download the file. However, I have been able to get a regular button that calls the following code and streams the file to the client and IE7 does not block it.
Sub PrintPDF(sender As Object, e As System.EventArgs)
     Dim crReportDocument as ReportDocument
     Dim crExportOptions as ExportOptions
     Dim crDiskFileDestinationOptions as DiskFileDestinationOptions
     Dim Fname as string
     CrReportDocument = New ReportDocument()
     CrReportDocument.Load(Server.MapPath("estactionlist.rpt"))
     Fname = Server.MapPath("./") & Session.SessionID.ToString & ".pdf"
     CrDiskFileDestinationOptions = New DiskFileDestinationOptions()
     CrDiskFileDestinationOptions.DiskFileName = FName
     CrExportOptions = crReportDocument.ExportOptions
     With crExportOptions
          .DestinationOptions = CrDiskFileDestinationOptions
          .ExportDestinationType = ExportDestinationType.DiskFile
          .ExportFormatType = ExportFormatType.PortableDocFormat
     End With
     CrReportDocument.Export()
     Response.ClearContent()
     Response.ClearHeaders()
                Response.AddHeader("content-disposition", "attachment;filename=test.pdf")
                Response.ContentType = "application/pdf"
                Response.Charset = ""
                Response.WriteFile(Fname)
                Response.Flush()
     Response.Close()
     System.IO.File.Delete(Fname)
End Sub
So here are my questions?
1. Is it possible to add a custom print control/icon to the CR viewer toolbar?
2. If one is not possible, then is it possible to override the CR viewer print and export buttons with your own subroutines like the one above?
I just want my page to look nice and hate to have print and export buttons outside of my CR viewer.
Thanks,
Kevin

It might be possible to replace the buttons in a windows app since you can retrieve the toolbar as a toolbar object in the winform viewer ( ToolStrip toolBar = (ToolStrip) crystalReportViewer1.Controls[3]; ) however with a web app, it's a lot more difficult.
The problem is that that you need to parse the Request string to try and figure out if the print / export button was clicked. The code below makes the print button disappear if you click it, so you should be able to modify it to call your custom printing / exporting code instead (You have to do this check in a postback)
        Dim I As Integer = 0
        If Request.Form.AllKeys.Length > 0 Then
            For I = 0 To Request.Form.AllKeys.Length - 1
                Response.Write(Request.Form.Keys(I).ToString & "<BR>")
                If Request.Form.Keys(I).ToString = "CrystalReportViewer2:_ctl2:_ctl2.x" Then
                    CrystalReportViewer2.HasPrintButton = False
                End If
            Next
       End If
Shawn

AP Check printing setups for printing checks on your own

HI
I am wondering if there a good document which deals with AP check printing with MICR and signature on your own check stock
thanks

Recently we started to deal with AP check printing in our organizatin. It was a daunting task with the information and resources scattered all over and missing critical pieces of information to make sense out of the whole process flow. We attempted to go through the AP check printing internally and succeded.
I decided to post the information for the benefit of people about the our experience
Check Printing Basics and Beyond for Printing Checks on Your Own
by
Sarma Chilukuri
This article deals with what is needed to get your own checks printed. It is a first attempt to uncover all the hidden rules that one should be aware to get your own checks printed. The first section deals with the basic AP check printing setup, while the 2nd half explores some of the flow of events that make it possible to print the check.
Part I â Basic Setup
AP Setup for check printing
There are multiple steps in the AP check printing. First set of steps deal with the AP side setups. The second step is to get the System side setups. The system side setup deals with printer setup and program options setups. The last step would be to make the print format files configured with the vendor provided escape sequences in the laser print format file.
Step 1: login as Payable Manager
Step 2: Bank Setup: Navigate to Setup: Payments > Banks
1.     Make sure the Bank # etc are present
2.     Tab to âBank Accountsâ, and make sure your account # has been setup
3.     On the Bank Accounts screen, tab to the âPayables Documentsâ and verify that Payment format (E.g., COK Laser Format) has been entered. This âPayment format links to next section where we associate it to the right payment program.
Fig 1. AP Payment Bank Setup Screen
Step 3: Program Setup (Setup: Payments > Programs)
As we know there are only 5 formats 3 of which are âEver Green Laserâ (APXPBFE G|L|F) which are explained in the AP Users Guide. For your own form printing, you have to associate the format to APXPFEL (laser format) program. Also, the APXPBFEL or APXPBFEF call the APXPBFEG, which is the base program that pulls the data from oracle base tables. APXPBFEL is the one which allows us to print the checks with MICR and signature on a plain paper not on a pre printed stationery.
Fig. 2 AP Payment Format Setup Screen
Printer Styles, Drivers setup
The above process summarizes the AP Setup. As a DBA, the printer setup needs to be validated. The base install provides the right setup to some extent. But the differences in printers and print queues may add some complexity to the final configuration. The following section discusses the set up the base install provides and changes as needed.
Step 1. Login as system Administrator
Step 2: Style (Install : Printer > Style)
Look for the âPORTRAITHPLJ4LASCHECKâ. This one is associated with the SRW Driver Called, âAPLASPâ (AP Laser printer format).
Step 3: Driver (Install : Printer > Driver).
     1. The âPORTRAITHPLJ4LASCHECKâ is associated with a âUser Driverâ of PORTRAIT for HPLJ4 and and a SRW driver of âAPLASPâ
     2. Also notice that there is an Initialization string at the bottom of it. This initialization string gets called as pre-report trigger for the APXPBFEG program (APXPBFEG.rdf) file. It sets the kind of format it should be. Please see the Appendix A for details on these printer pcl code translations. The Initialization string was as follows:
Initialization: /eE/e&l0o2a7C/e(s0P/e(8U
Step 4: Printer type (Install : Printer > Register)
Each printer type is associated with a set of styles. Make sure the printer that was selected has the above style and its associated driver listed against that.
Fig. 3 System Administrator Printer Seups
Step 5: Program Setup (Concurrent > Program > Define)
This step holds the key for check printing. It is necessary to define whether you need the check on top followed by the Stub or the other way around. The way it is controlled is based on the APXPBFEG.rdf, the report definition file and the APLASP.prt (Printer Style associate with the Portrait laser check format SRW driver). The APLASP.prt file ($FND_TOP/reports) has two identical setups called the 100 series and the 200 series. Those identical sets of setups define where the MICR and signature print on the check. The following table lists the some of the codes in the 100 series. Please refer to Doc ID #146452.1 for complete details.
Fig. 4 System Administrator Concurrent Program Definitions
CODE #     Code Definition
100     Electronic check activation string
101     1st Check #
102     2nd Check #
104     Deactivate check number mode string
111     Activate MICR line
112     MICR Deactivation / reset the printer head position
121     1st Signature
122     2nd Signature
141     Address font activation string
199     Return to default state string
Table 1. APLASP.prt -- MICR Activation Codes
The above code block repeats itself the same way in the 200 series. The decision to activate one way or the other controls the Check printing.
Step 2: Setting up the Option block
In the concurrent program definition for the APXPBFEL, there is an Options block in the middle. You need to list the codes that you want to activate. Please refer to Doc ID # 186640.1 for some explanation on these.
E.g.,
p_printer_code_mask="201,211,221,241" p_sig2_amount="" p_sig3_amount="" p_sig1_vendnum="" p_sig2_vendnum="" p_sig3_vendnum="" p_country_to_ignore="US" p_continuous_stationery="N"
Step 3: Output format is Text
Text format is sufficient, as the printer will pick up these escape sequences anyway.
Fig. 5 System Administrator Concurrent Program APXPBFEL Options Definition
UIPRINT.TXT, UIFONTS.ALI
One needs to be aware of a few more pieces in this puzzle. The UIPRINT.TXT identifies to the Oracle Applications the print queues that were setup. This file is needed to set your PCL / Post Script printer definitions. I did not have to really tinker with these files other than identifying the PCL and Post Script Qâs that were setup on the UNIX box.
Part II: Integrating all the pieces
The above setups are all documented in various articles. We need to understand a few more steps to see how all these pieces come together.
What you need to know about APXPBFEG.rdf
APXPBFEG (.rdf) is the report file which when called pulls the data from Oracle. If you open the APXPBFEG.rdf in the Oracle reports, there is initialization to the report called, SRW.Init. This will bring in the initialization string associated with the PORTRAITHPLJ4LASCHECK driver definition file. Also, please be very careful with this report format file. When you open it, there is small tiny empty block. in the first block which calls the printer initialization code 100/200 under the Format Mask (from APLASP.prt). If this portion gets changed or messed up, one can end up with some unexpected results. Each of those blocks like MICR, CHECK etcâ¦ have associated format triggers and printer codes.
Please make sure that the printer mask is properly handled. I noticed that the 200 series MICR (211) and Signature (221) printer masks were tied to 111 and 121 respectively. These should have been 211 and 221. The other place you need to be careful was the printer code before and after is proper.
For E.g.,
For the MICR, the âprinter code before and after columns â should be 111 and 112 (or 211 / 212) respectively while Format Trigger should reference to 111 (211).
Fig. 6 APXPBFEG rdf file printer mask and Format Triggers
The escape sequences in the APLASP.prt file for these codes will play the crucial role in getting our format around the report output that gets generated from the APXPBFEG program. Please refer to the explanation of these escape sequence codes in the APPENDIX A.
At this point when you run the program, you will see that the formatted output report file will have all the initialization strings and the output associated with that. You can compare the fields and verify the results. Let us closely examine the parts of the 111 and 121 where the micr and signature prints. The key to this to code the escape sequences the right way to get the associate MICR and signature print out correctly.
Fig. 7 APXPBFEG rdf file MICR printer mask and Format Triggers
Code 111 and Code 112 from the APLASP.prt file.
I broke the line into pieces to illustrate the exact escape sequence code.
Code "211"
Part 1: esc "&f0S" esc "&f0y0X" esc "&l0E" esc "&a0L"
Part 2: esc "(8M" esc "(s0p8.00h8.0v0s0b80T" --- This will be provided by the ROM
Cartridge provider
Part 3: esc "&k15H" esc "*p3215Y" esc "&a13.8C"
code "212"
Part 1 : esc "&f1x3x8X"
Part 2 : esc "&f1S"
Let us go over these 2 sets of codes carefully.
Escape Code     Meaning     Comment
esc "&f0S"      Push Cursor Position
esc "&f0y0X"     Define Macro ID 0 and Start Macro Definition
esc "&l0E"      Define Top Margin at 0 Lines
esc "&a0L"      Define Left Margin at Column 0
esc "(8M"     8M Symbol SetNote : As per pcl codes this happens to be Font Primary JIS Math 8 symbol     MICR Part 1 : Provided by the Vendor from where you the ROM cartridge
esc "(s0p8.00h8.40s0b0T"     {Fixed Pitch}{pitch 8.00 cpi}{Font Style 8.40}{Medium Weight}{Typeface 0}     MICR Part 2 : Provided by the Vendor
esc "&k15H" esc "*p907Y"     Set HMI = 15/120" Vert position = 907 Dots
esc "&a13.8C"     Move to Column 13.8
     CODE 112
esc "&f1x3x8X"     {End Macro Definition}{Call Macro}{Delete Macro ID}
esc "&f1S"     {Pop Cursor Position}     At this point, the MICR gets printed
Table 2. Escape Sequences in APLAP.prt file Explanation
Fig. 8 APXPBFEG rdf file Signature printer mask and Format Triggers
The signature piece (221) has also similar meaning.
Escape Code     Meaning     Comment
esc "&f0S"     Push Cursor Position
esc "*t300R"     300 DPI Graphics resolution
esc "*p1500X"     Horiz position = 1500 Dots
esc "*p650Y"     Vert position = 470 Dots
esc "(4B" esc "(s1p53v0s0b102T"esc "&f0S!"     Symbol SetProportionalPoint Size 53UprightMedium WeightTypeface 102Push Cursor Position!     Vendor gave the us esc "(4B"esc"(s1p53v0s0b102T!"Note: the ! when the it pushes the ! and that is where it prints the signature piece. The first part forms the symbol set , say (4B and the later part forms the signature font and ! is the piece. I took the ! from the above and let it stay with the 3rd part of it so that signature does not print twice.
esc "&f1S"      Pop Cursor Position
esc "*p+121Y"     Move down 121 Dots
esc "&f1S"     Pop Cursor Position
Table 3. Escape Sequences for Signature in APLAP.prt file and Explanation
Summary
One can print their own checks using the above steps. This can work as a cost effective solution for small organizations where the budgetary constraints are tighter. We are successful in getting the AP Checks printed using the above method.
References
Metalink Doc ID # 186640.1, Different Payment Formats â¦
Metalink Doc ID # 60936.1, Step by Step Guide to Setup a Printer in Oracle Applications
Metalink Doc ID # 250543.1, How to Create An Initialization String for a Payable Check Format
Metalink Doc ID # 48680.1, Accounts Payable FAQ â Payment Batch, Check
Metalink Doc ID # 1074792.6, Exclamation Point (!) Prints On Check When Using APXPBFEL And Cartridge
Metalink Doc ID # 158486.1, APXPBFEL Evergreen (Long Laser)
Metalink Doc ID # 146452.1, Listing of p_printer_code_mask Default Values for APXPBFEL
Chapter 2, Oracle Payables user guide
Appendix A
APLASP.prt printer codes explanation
code "200" esc "&l0o2a6d66p8.000c2e1x0l63f1H" esc "&k12.00H" esc "(8U"
esc "(s0p10.00h12.00v0s0b3T" esc "&k11.75H" esc "&a1l0R" control(M) esc"&f3005y4X"
{Portrait}
{Letter}
{6 LPI}
{Define Page Length to 66 Lines}
{Set VMI = 8.000/48"}
{Define Top Margin at 2 Lines}
{Select 1 Copies}
{Disable Perf Skip}
{Define Text Length as 63 Lines}
{Feed from Tray 1 (upper)}
0.1 esc "&k12.00H"
{Set HMI = 12.00/120"}
0.2 esc "(8U"
{Roman-8 Symbol Set}
0.3 esc "(s0p10.00h12.00v0s0b3T"
{Fixed Pitch}
{pitch 10.00 cpi}
{Point Size 12.00}
{Upright}
{Medium Weight}
{Typeface 3}
0.4 esc "&k11.75H"
{Set HMI = 11.75/120"}
0.5 esc "&a1l0R"
{Define Left Margin at Column 1}
{Move to Row 0}
control(M)
0.6 esc"&f3005y4X"
{Define Macro ID 3005}
{Enable Overlay}
code "201" esc "&f0S" esc "&a1.25r70C" esc "(8U" esc "(s1p14v0s3b4148T"
{Push Cursor Position} esc "&f0S"
1.1 esc "&a1.25r70C"
{Move to Row 1.25}
{Move to Column 70}
1.2 esc "(8U"
{Roman-8 Symbol Set}
1.3 esc "(s1p14v0s3b4148T"
{Proportional}
{Point Size 14}
{Upright}
{Bold}
{Typeface 4148}
code "202" esc "&f0S" esc "&a20.25r70C" esc "(8U" esc "(s1p14v0s3b4148T"
{Push Cursor Position}
2.1 esc "&a20.25r70C"
{Move to Row 20.25}
{Move to Column 70}
2.2 esc "(8U"
{Roman-8 Symbol Set}
2.3 esc "(s1p14v0s3b4148T"
{Proportional}
{Point Size 14}
{Upright}
{Bold}
{Typeface 4148}
code "211" esc "&f0S" esc "&f0y0X" esc "&l0E" esc "&a0L"
esc "(0Q" esc "(s0p8.00h8.40s0b0T" esc "&k15H" esc "*p907Y" esc "&a13.8C"
{Push Cursor Position}
11.1 esc "&f0y0X"
{Define Macro ID 0}
{Start Macro Definition}
11.2 esc "&l0E"
{Define Top Margin at 0 Lines}
11.3 esc "&a0L"
{Define Left Margin at Column 0}
11.4 esc "(0Q"
{0Q Symbol Set}
11.5 esc "(s0p8.00h8.40s0b0T"
{Fixed Pitch}
{pitch 8.00 cpi}
{Font Style 8.40}
{Medium Weight}
{Typeface 0}
11.6 esc "&k15H" esc "*p907Y"
{Set HMI = 15/120"}
{Vert position = 907 Dots}
11.7 esc "&a13.8C"
{Move to Column 13.8}
code "212" esc "&f1x3x8X" esc "&f1S"
{End Macro Definition}
{Call Macro}
{Delete Macro ID}
12.1 esc "&f1S"
{Pop Cursor Position}
code "221" esc "&f0S" esc "*t300R" esc "*p1500X" esc "*p470Y"
esc "(30C" esc "(4B" esc "(s1p53v0s0b102T!"
esc "&f0S!" esc "&f1S" esc "*p+121Y" esc "&f1S"
esc "&f0S"
{Push Cursor Position}
21.1 esc "*t300R"
{300 DPI Graphics resolution}
21.2 esc "*p1500X"
{Horiz position = 1500 Dots}
21.3 esc "*p470Y"
{Vert position = 470 Dots}
21.4 esc "(30C"
{30C Symbol Set}
21.5 esc "(4B"
{4B Symbol Set}
21.6 esc "(s1p53v0s0b102T!"
{Proportional}
{Point Size 53}
{Upright}
{Medium Weight}
{Typeface 102}
21.7 esc "&f0S!"
{Push Cursor Position}
21.8 esc "&f1S"
{Pop Cursor Position}
21.9 esc "*p+141Y"
{Move down 121 Dots}
21.10 esc "&f1S"
{Pop Cursor Position}
code "222" esc "&f0S" esc "*t300R" esc "*p1500X" esc "*p650Y"
esc "(30A" esc "(s0p.426h35.25v0s0b128T" esc "&f0S!"
esc "&f1S" esc "*p+141Y" esc "&f1S"
{Push Cursor Position}
22.1 esc "*t300R"
{300 DPI Graphics resolution}
22.2 esc "*p1500X"
{Horiz position = 1500 Dots}
22.3 esc "*p650Y"
{Vert position = 650 Dots}
22.4 esc "(30A
{30A Symbol Set}
22.5 esc "(s0p.426h35.25v0s0b128T"
{Fixed Pitch}
{pitch .426 cpi}
{Point Size 35.25}
{Upright}
{Medium Weight}
{Typeface 128}
22.6 esc "&f0S!"
{Push Cursor Position}
22.7 esc "&f1S"
{Pop Cursor Position}
22.8 esc "*p+141Y"
{Move down 141 Dots}
22.9 esc "&f1S"
{Pop Cursor Position}
code "241" esc "&a-100V" esc "&l5.8C" esc "(8U" esc "(s0p12.00h10.00v0s3b3T" esc "&k11.75H"
41.0 esc "&a-100V"
{Move up 100 Decipoints}
41.1 esc "&l5.8C"
{Set VMI = 5.8/48"}
41.2 esc "(8U"
{Roman-8 Symbol Set}
41.3 esc "(s0p12.00h10.00v0s3b3T"
{Fixed Pitch}
{pitch 12.00 cpi}
{Point Size 10.00}
{Upright}
{Bold}
{Typeface 3}
41.4 esc "&k11.75H"
{Set HMI = 11.75/120"}
code "299" esc "(8U" esc "(s0p10.00h12.00v0s0b3T" esc "&k11.75H" esc "&l6D"
{Roman-8 Symbol Set}
99.1 esc "(s0p10.00h12.00v0s0b3T"
{Fixed Pitch}
{pitch 10.00 cpi}
{Point Size 12.00}
{Upright}
{Medium Weight}
{Typeface 3}
99.2 esc "&k11.75H"
{Set HMI = 11.75/120"}
99.3 esc "&l6D"
{6 LPI}

So I can update my Oracle Java Applet Plug-in to Development Kit 7, Update 65, can you link me to the correct Oracle download page from your Plugin Update page?

When I periodically accessed your Plugin Check and Updates web page in the past, I really appreciated you connecting me to the correct Plugin Updates vendor web page when I clicked on your red Update Now button. This time, however, your Java Applet Plug-in "Update Now" button linked me to the Oracle Java "7u65 Updates Release Notes" instead of the usual download page. It seems rather unexpected for me, or any other conscientious user for that matter, to search the appropriate "JDK 7U65" file download from the Oracle website.
Thank you,

This is getting way too complicated for normal peop.
First: the "Update Plugin" does not work, it goes to a page with all sort of computer jargon but no "Update button" anywhere.
Second: this forum jscher2000 gives a good solution, but I downloaded the incorrect java update, because my computer is 64 bit. how am I supposed to know my browser is what it refers to and that FF is 32 bit.....???$%^&*()??
Third: some of those "critical update" software are not even on my computer....well at least I don't think it is, I search for "shockwave" and did not find it.
I love Moz FF but the updating is starting to get out of control. why give us (computer idiot) an auto recommendation update not tailored to our computer? Perhaps in big letters at the top there should be an explanation "this is general suggestion these plugin needs updating, not to tailored with your computer, do your own research"
and/or add info I need to know like the 32 bit thing, took me forever to download the 64bit update for JAVA and it was the wrong one.
Now I am just afraid to update anything for FF because it is too darn confusing.

Using your own router

Good day all, I would like to hear from others who use their own routers to connect to Verizon Fios. Are there any pro's or con's to using your own? Will your connection be more secure using Verizon's equipment or your own. Any difference in speeds noted? Thank for your opinions.

Just got FiOS today and faced the same issue. I need to keep the Actiontec router for the TV STBs, but it has not the same features as my D-Link 655. There are instructions online on how to turn the Actiontec into a network bridge, but that may interfere with services.
Here is what I did:
1. Change the IP of the Actiontec router to something different than the 192.168.1.1 so that it doesn't interfere with your existing router (unless your router already uses a different IP, then you can skip this). I followed the instructions from here: http://www.dslreports.com/forum/r20329726-northeast-how-to-change-the-default-IP-on-Actiontec-M1424W...
Note 1: Once you change the address you need to reconnect to the other IP address!
Note 2: You also need to change the DHCP range on the Actiontec to no longer include the new IP. This can be changed on the same page.
2. Make sure that you power cycle the STBs, otherwise they still look for the router on the old address
3. Plug your router of choice in and connect one of the LAN ports of the Actiontec to the WAN port of your router
4. You now should be able to access Internet through your router.
I use DynDNS so that I can remote into a system at home using a domain name. If you have such a setup be aware that the web admin of the Actiontec will be accessible from the Internet!
I fixed that by
1. Setting the Actiontec's firewall to the lowest setting
2. Forwarding all TCP and UDP ports to my router except for the port 4567. That apparently is used by something for Verizon (the TV STBs??), so you may need to create multiple forwarding rules. If you choose custom ports you can specify a range, which is really nice. This way all traffic except for port 4567 hits my router and either goes where I forwarded the ports to or goes nowhere as there is no service.
This setup should provide the best of both worlds. I say should as I yet have to test it for a while,but so far things are working out OK.
If you have your own wireless and don't need the wireless from the Actiontec then turn the wireless off on the Actiontec and detach the antenna.

I want my new TAB to open blank,but have installed a s/w which opens it's own search page when i open new tab??Help appreciated.

I want my new TAB to open blank,but have installed a s/w which opens it's own search page when i open new tab??Help appreciated

Software? See if you can get it removed with some anti-malware tools. Spybot, AVG, Kapersky, et cetera...
If you know the name of the program, you could search the registry for any instance of that name and --be CAREFUL--delete them.
And I have to ask: Did you go back to Firefox after uninstalling this program and reset the "when I open a new tab..." setting? What about your home page?

Direction: Member Own Home Page

Hi there,
DW 8.0.2, PHP with mySQL database.
In ASP VBScript I can help myself around building a member
page where a
member can login and update his/her detail.
Now I want to build, in PHP, a login page and according to
the login
page, the member's "own" home page displays. On this Home
page I want to
have some links to update details and view back orders. The
back orders
will be in the form of a down loadable PDF document which
will be
updated daily.
I trust you clever people understand what I mean with "own"
Home Page.
I don't expect someone to do everything for me, as I will
choose to do
this from some tutorial.
Really looking forward to your help.
Regards,
Deon

Be sure to select in the same session(startup session in general tab) in '''WHEN FIREFOX STARTS ''' to '''SHOW MY HOME PAGE''' after your put the desire start page in HOME PAGE session.
thank you
Please mark "Solved" the answer that really solve the problem, to help others with a similar problem.

EXS24 sampler, load your own samples?

Is it possible now to load your own samples (wav, aiff) in the exs24?

Hi,
yes, you can! In the upper right corner of the EXS24 main window (above the main volume knob) there's an edit button. Click on it, and the editor window pops up. In this window you can use your own samples to build a new patch. In Logic, click on Help > Logic 8 Instruments & Effects. A pdf file opens up, and on page 312 a section starts about creating your own patches. Tip: from page 275 of this "Instruments & effects" manual there's a general explanation of the EXS24.
Kind regards,
Jaap

Droid X2 Should Have Their Own Support Page.

I know this has been brought up in previous post (maybe it's own thread) correct me if I'm wrong, but I really think VZW Community should have their own support page. I feel that it's a nuisance to put Droid X2 in every subject box when you want to post a message about the X2 device. I think I've read it's only put together because they are so similar but so are the Inc. And Inc. 2, Minus the camera on the X2 as the X has one (and dual core.) And the minus the scrolling button from the Inc. To the Inc. 2. Yet they have their own support pages as to no one getting confused. The X and X2 are quite different in my opinion. As to the hard reset is different...builds are different...a few different apps and widgets I believe. Also many of the people that give advise could get confused as to how to solve your problem as to either being on an X or X2...I think it would just make things way easier for the X2 owners to receive support. Just my .2 cents though. Hope something can be done about this. Thanks.

@RIPCharge
Actually the X and X2 in fact have so many things in common that it makes since to keep it group with the X because if you look at the track history the X2 has went through almost all the same issues that the original X did when it was first released, the device uses the same charger, battery, docks and other accessories.
In my opinion Motorola has took its pointers from Apple recently, instead of updating the hadware they learned that they can change out a feature here and there and sell the device as a new better device, also they proved the patteren they are following with the Razr and it non-removable battery.. (Screams Apple to me).
There isn't a logical reason to make a thread that will be doing nothing but repeating the same thing already covered from the original X and as for the reset being diffrent this is software related and once the next update hits the reset process will probally change to match the X2 method.

A 'Do your own homework' page?

Similar Messages

Maybe you are looking for