A few keys not working - faulty keyboard?

Hi,
A friend of mine (honest!) spilt a v.small amount of water on her keyboard on her 2.16ghz 17" MBP and decided to dry it out using a hair dryer.
One melted keyboard later and I was asked to replace her keyboard for her.
So having bought and fit a new keyboard, keys are not working and 1 is intermittant. These keys are: f10, f11, 0, - and p ([ is intermittant).
They are all grouped together near the top right of the keyboard.
Twice I have tried to ensure the keyboard ribbon cable is firmly in place and it seems to be. Is the new keyboard I bought likely to be faulty and there needs returning, or could this be some other problem.
Thanks in advance for all your thoughts!
Dominic

Did the new keyboard come with a new cable? You might want to carefully examine the cable under strong magnification and look for any breaks that might correspond to the keys that are not working or not working properly.
Also, try an external keyboard. If you have the same situation on an external, there is some problem other than the replacement keyboard.
For future reference for your friend, you NEVER want to use a hair drier on a water spill. The best thing to do is to turn the Mac off, remove the battery, and lay it keyboard down on a towel for several days. You want all the water to drain out and any internal residue to dry completely before putting power to the machine again. Most of the time, the water will dry and everything will work again.
The forced air from the hair drier could have blown water deeper into the machine and there could be some residue causing problems. When you take the machine apart to check the cable, also check for any remaining moisture that could still be causing problems. If the machine had not been allowed to dry for several days, it needs to.
Good luck!

Similar Messages

  • Satellite P300 - One Key not working on keyboard

    Hi all,
    Does anyone have a suggested solution to fix a key not working on my laptop? One letter on my keyboard "the letter b" has stopped working.
    Laptop is Satellite P300- "PSPCA-01U013"
    Thanks :)

    Hi Ricco1,
    The problem is that single keys cant be replaced so if a certain key doesnt work its time to replace the whole keyboard but dont worry, new keyboards are not so expensive. Just get in contact with an authorized service provider and ask for a new keyboard, the guys are able to order a new one and they can replace it for you if cant do this yourself.
    Here you can find a list of all ASPs:
    www.mytoshiba.com.au > Support > Find a service center

  • Certain keys not working on keyboard

    When attempting to hit the "O" key and or the "P" key it hits the letter above and or around the requested keys. Does anyone else have a problem when attempting to text someone and you can't hit either key? Extremely frustrating!

    Yes, the "magic rice trick" doesnt work.
    inexpensive repair? No.
    Liquid spills, why your MacBook chassis is a one-way valve for spills
    After a substantial spill many people will turn their notebook upside down and shake it, not only does this not work, but it spreads liquid havoc throughout your machine and makes things often as bad as possible.
    The keyboard itself acts like a one way valve in the case of a substantial liquid spill. While liquid pours into the bottom chassis easy, it does not come out easily at all, and in the case of any spill, most of it will not come out by turning it upside down. Disconnect all power and contact Apple for diagnostics and repair.
    Do not attempt to, after a spill, ‘dry out your MacBook’ and test it
    After a spill most people invariably try to “dry out” their notebook by various methods, including hair dryers and otherwise. This both does not work, and after a substantial spill of any magnitude, even if the liquid was water, residue is left behind.
    There are additionally many very tight places inside your notebook where liquids will linger for a very long time, and cause corrosion or worse.
    Immediately unplug your notebook and contact Apple for in shop diagnostics and parts replacement.
    In the case of very minor spills people will “dry out” their notebook and feel success that their notebook is working ok, however invariably in nearly all instances after 4-14 days an error / fault pops up and is usually followed by more.
    In case of a spill, damage estimates are impossible,.....anything can be fixed, without question.......the question is cost.
    contact Apple for in shop diagnostics and cost estimation ....possible parts replacement.  

  • Some keys not working on keyboard on Pavilion G6 with windows 8

    Hi, Some of the keys (,backspace,h,g ect) are not working on my laptop, i have windows 8 installed and i have tried to do a restore settings but it did not work.
    Any suggestions would be appriciated

    Hi desiree79,
    Welcome to the HP Support Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
    I saw your post regarding the problems with your keyboard. I have included a HP document below with some steps to follow. There is a section on Stuck Keys check that out first.
    Notebook Keyboard Troubleshooting Windows 8
    Thank you,
    Please click “Accept as Solution ” if you feel my post solved your issue.
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    Thank you,
    BHK6
    I work on behalf of HP

  • Few keys not working

    Hello,
    I spilled some water on my hp Pavillion g4-1200 tu Notebook PC about a month ago. I wiped the water immediately but since then I have been noticing that some keys have become hard to press and yesterday some keys even stopped working. At times some keys works and at times they dont. Please help me as I have already cleaned my laptop and have also used a hairdryer to wipe of the dust but it is not working as such. I tried using the driver scanner on hp's website to see if the laptops drivers were up to date even that didnot work successfully though the keyboard driver is up to date.
    Thanks

    The keyboard is mechanically damaged, no driver will fix your problem. Unless you have skills in cleaning keyboard internally , you are set to buy a new keyboard and install it.
    Check your laptop technical manual for more details

  • Curve 9300 3G - A few Keys not working properly

    Somebody close had gifted this Blackberry Curve 9300 3G mobile to me. After using it for just 2 months, the Space, alt and 0 keys are not working properly. At times I just have to keep pressing for these respective keys to respond and at times upon pressing, these keys respond more than once. Does anybody know how to tackle this issue.
    Regds
    AK

    Maybe your Keypad Membrane not working 

  • Dimmer and volume keys not working on keyboard

    I went to up my volume from the f5 key on my keyboard and it didn't work. I tried to dim and lighten the screen and that too didn't work. Any suggestions on how to resolve this situation?

    Did you check your Keyboard Shortcut settings in Sys. preferences, Keyboard & Mouse perhaps something is off there.
    *Your Question being marked as solved does not seem accurate, since you still have the issue with these 2 items.Hope this explains how to mark your Question / Topic Answers, Helpful and Solved
    Eme;~[)

  • Launch Keys not working on keyboard

    I have a keyboard with some special launch keys.  I am able to set some of them with KDE's global shortcuts settings, but others aren't recognized when I try to set them as the trigger.  They are recognized in dmesg though as unknown keys.  How do I get these buttons to work?
    Thanks.

    I've had no luck following this page https://wiki.archlinux.org/index.php/Ma … o_keycodes
    I'm using a PS/2 keyboard, not USB.  I'm having no luck either using the hwdb or setkeycoads.  I just can't seem to get KDE to recognize the key.

  • Keys not working on keyboard

    Hi all,
    Keyboard randomly stopped working overnight:CAPS lock, n and b keys won't work but are not stuck. Sometimes a u will appear instead of n. Typing via OSK. Computer had been working fine although it was giving me weird messages yesterday about the wrong charger when I plugged in, when it was the same charger it's always been (that came with the product July 2014).
    Regards,
    ikki

    Dear Customer,
    Welcome and Thank you for posting your query on HP Support Forum
    It looks like you are having issues with the Keyboard on your Notebook.
    We will surely assist you with this.
    Let’s start with a questions:
    1. Was there any liquid split on the Notebook Keyboard
    2. Is there any Dust settled on the Notebook Keyboard
    3. Are there any Keys which are fallen off / Any Keys which are loose
    Troubleshooting: 
    Step 01. Click on the Start Button and go to Control Panel
    Step 02. Open the Device Manager and expand the Keyboard from the list
    Step 03. Right click on Standard PS/2 Keyboard and click on Uninstall
    Note: This driver will get installed again automatically on your Notebook
    Step 04. Please turn OFF the Notebook
    Step 05. Un-plug the Power/AC Adapter and also remove the Battery too
    Step 06. Press and Hold the Power Button of the Notebook for a full minute
    Step 07. Now let's re-insert the battery back in and plug back the Power/AC Adapter
    Step 08. Start the Notebook and keep tapping F10 Key during the startup to access the BIOS
    Step 09. Once you get to the BIOS, Please press F9 or F5 Key[Model specific] to load setup defaults for the BIOS
    Step 10. Use the arrow keys to say "YES" and hit enter
    Step 11. Now let's press Esc/Escape Key. Save Changes and Exit - Yes
    Step 11. Now please wait till the Unit loads the Windows Operating system
    If the issue still persists please check and verify if an External Keyboard works fine with your Notebook
    Note: Please click on the below shown link to find more troubleshooting steps
    http://h10025.www1.hp.com/ewfrf/wc/document?docname=c03738933&tmp_task=solveCategory&cc=us&dlc=en&lc...
    Hope this helps, for any further queries reply to the post and feel free to join us again
     **Click the White Thumbs Up Button on the right to say Thanks**
    Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.
    Thank You,
    GBL84
    Although I am an HP employee, I am speaking for myself and not for HP

  • Keyboard Keys not working / Backlit Keyboard Not Lighting Up

    Hi,
    I purchased my macbook pro in February of 09. Recently I have come to realize that the following keys: (alt key, left shift key, and control key) have stopped working and the right half of my keyboard has stopped lighting up when the lights go dim. What can I do to fix it and will it cost me if I'm under warranty.
    Thanks Apple Community!
    Cheers,

    you just need to do a SMC (systems management reset) and all will be good again. i had the same issue after i installed snow leopard
    1. shut down your MacBookPro and unplug everything attached but your power source
    2. press down "shift" + "control" + "option" + "power button" for 2-3 seconds and release
    3. nothing should have happened (macbook remains off)
    4. power it up in normal fashion
    that should do it....my beautiful backlit gem-like keyboard was all better!

  • A s d f g keys not working on a wireless Apple keyboard for Imac

    a s d f g keys not working on a wireless Apple keyboard for Imac.
    When I type they on't work.
    *Exmple o complete entence.
    Plee help! Thi i very rutrtin. I on't wnt to ue cut n pte or ome letter.
    Thnk you in vnce.

    Make a Service appointment for the keyboard at your local AASP.
    Apple - Find Locations
    I'm not sure how old it is, but it is covered for 1 full year as long as it didn't take that 19 story dive.

  • Volume and brightness keys not working with new keyboard on imac

    I just purchased a new wired keyboard for imac and brightness and volume control keys not working . i have tried adjusting keyboard settings. I have software version 10.5.8. Do I need to upgrade software. Thank you for any help.

    Do you have "Automatically Adjust Brightness" check box ticked in System Preferences > Displays > Display ? If so, you can't manually adjust brightness.

  • Keyboard: some keys not working

    Some keys not working.  Need help/suggestions.  Not great with computers so PLEASE give details/steps re: how to do what you suggest - thanks!
    Details: intel based iMac running snow leopard 10.6.8.  Apple wireless/bluetooth keyboard (came with the iMac).
    Some keys suddenly stopped working:  space, tab, capLock, option key to the right of space bar (one on the left works), down arrow
    The problem happens in various programs (safari, pages, etc)
    The keyboard is fine on another iMac
    A different keyboard is fine on this/the involved iMac
    (nutshell: keyboard works fine - computer works fine, unless they're together)
    Here's what's been tried/checked:
    -checked the settings for universal access ("mouse keys" are off) and checked for any bluetooth keyboard shortcuts.
    -in system preferences "speech" is not set for "speak selected text when the key is pressed" - this is not checked/selected
    -tried creating a new user but had the same issue so it's computer-wide rather than just a user account
    -removed the keyboard and reconnected (using the +/- signs and "disconnect" and putting in a new code of numbers to pair keyboard)
    -language/text is set for english
    -did the keyboard viewer and the keys in question did NOT highlight when pressed (but don't forget the entire keyboard is fine on a different computer so thekeys aren't the issue)
    -"slow keys" is turned off re: keyboard in system preferences.
    Any help is welcomed.  It's frustrating knowing the keyboard works, just not with this computer.  Please help.  Many thanks!

    yes - not sure how this works...if you can see my original post there are a lot of details in there.  If you can't...
    nutshell: the keyboard works on a different iMac
                 a different keyboard works on this/the involved iMac
                 I tried to create a different user and the keyboard still does not work so it is computer-wide
                 I also removed the keyboard from the computer (using the +/- symbols and disconnecting and then repairing it.  The problem remained
    Thanks for any help.  It's crazy that the keyboard is fine and the computer is fine but together, there's the problem.
    Thank you!!!

  • My backlit keyboard keys not working?

    How come my backlit keyboard keys not working? When I try to use them I get a circle with a line running through it?

    cpickrell wrote:
    Jax, the backlight is currently usinig a sensor to turn the light on and off for you. This uses the least amount of battery. If you want to test or control the lighting yourself, go to the Apple Menu, select System Preferences, click on the Keyboard icon. Here you can turn the automatic setting on and off. If it is off, you can use they keyboard keys to turn the keyboard lighting on and off.
    Exactly!

  • Wired keyboard-number pad&right arrow keys not working-serial # help!

    Hello to whomever reads/replies -
    I have a wired keyboard for my iMac(it's not the aluminum imac, but the version before it with the keyboard and mouse that came with it). I got this keyboard June 2007 after the original keyboard sent to me had problems with it with some keys not working properly. And now about a week ago my right arrow key and the zero, decimal point, one, two, three and enter button on the keypad stopped working out of the blue. One night they worked and the next they didn't with nothing being done different, nor was the keyboard stored differently.
    I've cleaned the keyboard inside and out twice and tried pushing the little squishy thing under the keys when you pop them off and there's no response with those being pushed either so something's got to be wrong with the keyboard itself.
    Also, when I go online to look up the warrenty on this keyboard, #1 i can't find where it tells me where the serial number on the **** WIRED keyboard is, just gives me where i can find it on the WIRELESS keyboards. Ugh. So I looked under my keyboard and punched in the numbers and letters that i found on a little silver plate just below where the wire and USB ports are in the top of the keyboard and I get an 'invalid serial number' error message.
    So.. could anyone help me with these problems? I'd really rather not call tech support since it took me over two hours to explain to the man that I spoke with last year about my other keyboard and I just don't have the time! Thanks in advance!
    Sharon

    Hello sharon:
    Welcome to Apple discussions.
    Run, don't walk to the phone. Call Applecare and indicate you have a warranty problem. The KB is (or will be shortly) out of warranty. It may take you some time, but it may save you some money in the long run.
    Incidentally, it appears to me that your KB is, indeed, broken.
    Barry

Maybe you are looking for

  • Not Writing Captions to IPTC???

    When sorting my images, I need to add; caption, keywords, copyright notice, copyright URL, source, and author. Until now I have always done this using two pages in the File Info Panel; Description and IPTC status. Since upgrading to CS3, all of the l

  • Livecache on different clients

    Hi, I am using APO for two different clients. It is working fine for the original one, but I am having different issues (see below) when I CIF the transtactional data. What should I consider for Livecache being shared on different clients? Issues - M

  • No Conflict editor in the Repository

    Hi, I am working on a project using XI. When browsing though documentation I noticed some references to a conflict editor. When we use the Release transfer function to transfer between software component versions we will get a screen indicating there

  • Mouse hover style not changing

    Hello I am working on branding and am not getting the mouse hover css  like About Us same I want to do in Resource,selfservice,AdminLinks in second image Thanks,

  • MS Captcha not showing image in production.

    I am using MsCaptcha for validation on my website but captcha image is not always displayed when website is hosted on cloud.It displayes a blank image with a red cross on left side of image ,if I right click on image and choose the option show pictur