A little help re: memory timings.

Alright guys,
I'm a little confused with how the memory timings specified by corsair map to the settings in the BIOS, so if anyone can point me in the right direction, it'd be much appreciated.
Corsair state: Cas Latency : 2-3-3-6-T1
Cheers!

Quote
Originally posted by syar2003
Also note that corsair on certain models (xms3200C2xxxx )with C2
in the articlename has a * stating cas latency=2 is for Intel P4 and cas 2.5 should be used for AMD cpu's.
Transform the settings 2-3-3-6 1T (a-b-c-d e) to:
a) CAS Latency (Tcl) : 2 (or 2.5)
b) RAS to CAS delay (Trcd) : 3
d) Min RAS# active time (Tras) : 6
c) Row precharge time (Trp) : 3
e) 1T/2T Memory timing/Commandrate : (auto/1T/2T) 1T gives best performance .
Cheers mate, that's perfect. I left them at auto initially, anything else was giving me stability issues. Hopefully this will clear it up.
Thanks again.

Similar Messages

Memory timings, weird bios behaviour, frustration...

Hi.
I recently bought a MSI 875P mobo, a P4c 2.4GHz to go with it and also 2x512MB Kingston HyperX PC3200 memory.
First thing I did was flash the bios to the newest version (1.8), which, after reading things from another thread might not have been such a great idea after all.
Seems that the CAS latency setting in the bios does not do anything. No matter if its set to 2, 2.5 or 3, CPU-Z always shows 2. Also, im getting quite frustratign results when overclocking with this mobo, no matter how much voltage I give to the memory (I have tried as much as 3,2v) whenever the memory bus is over 200MHz the system wont be stable. It seems as if the memory voltage setting doesnt do anything, as it doesnt matter if its set to 2.5 or 3.2 it wont be any more or less stable. (I know over 200MHz is over spec for this memory but the mem is supposed to do alot better than that, especially when increasing the voltage.) Also even with low memory speeds im unable to get the CPU to go very high... it does 3GHz (250MHz FSB) fine with default core voltage, but anything above that wont be stable no matter what CPU core voltage I use. Could be my CPU, but I suspect the motherboard to be the reason with so many faults already.
Theres also some weird behaviour by the bios I have seen. For example, sometimes the AGP/PCI divider has three settings (66,75,83MHz) and sometimes it allows me to set the frequencies by 1MHz steps, but still so that there is no 66MHz setting at all, just 67 - 83MHz and one extra setting which gets adjusted as I adjust the FSB. Also, sometimes when I try to go into the BIOS setup, I only get a black screen. This often happens if I press some other key (for example tab) before pressing del during POST. weird and extremely annoying.
Is there any hope that issues such as these would be resolved in a future bios update? I'm a little frustrated after setting up this system with watercooling etc. and now being stuck with this motherboard doing weird things and certainly not being a good mobo for overclocking!
In case these issues wont be solved in the near future, I will propably switch to another brand motherboard... Anyone reading these boards with good experience from other manufacturers, preferably similar boards as the 875P in terms of features (wanted ones)?
any help appreciated (preferably from someone from MSI),thanks.

Quote
Originally posted by DOS
If you set any performance setting other than Slow the memory timings are set for you. If you want to overclock to 3G set the ram voltage to max 2.8, set the performance mode to Slow (bad term - is should be 'Normal'), set the DRAM clock to 333 (this will run the ram at 320 when FSB is at 200, also referred to as 5:4 ratio), set your FSB to 250. This will clock the ram at 400. You should be able then go further.
This is what I have done, the performance setting is set to slow, and even right now I have CAS 3 set in the bios but cpu-z still shows its using CAS 2. Using 333MHz DRAM clock with 250MHz FSB is stable at all default voltages, but anything above those wont work, no matter what voltages. If I set the FSB to 255, it wont be stable anymore, not even with 1.7v vcore and 3.3v memory voltage. Even setting the DRAM clock to 266MHz wont be stable with 255FSB. Also, running a lower FSB with a higher memory clock, so that the FSB is lower but memory goes above 200MHz wont be stable no matter what.

[865PE/G Neo2 Series] Memory timings and power settings anyone?

I'm not very good with computers, so I've just played around with the timings on my memory, but have not found one stable setting as of yet.
The memory is brand new and I've tested it for errors on my brothers computer and there's nothing wrong there.
Intensive harddrive usage, dvd playing and intense downloading while listening to music are sure ways to crash my system. "..........Not less or equal" is the most common error message, but there are
many many more.
Oh, maybe I should point out that overheating's not an issue, cause I've good fans and run my computer without sidepanels.
I also like to say that I have the first generation of p4 with ht and 533fsb.
I'm sure there's something I forgot to mention but here below I'll paste the system summary that Sandra gave me.
Would be forever grateful if someone could help me out with the memory timings and power settings for my board. Setting it to "auto by spd" gives me a very unstable system, so no avail there.
I'm running the mem at 2.70 and sometimes at 2.65, since these two settings seem to be the ones with least crashes.
The Memory installed are 4*512mb ,kingston 512 kvr333x64c25 pc2700
The PSU is a Tagan "TG480-u01" 480w
Many many thanks in advance guys.
SiSoftware Sandra
Processor
Model : Intel(R) Pentium(R) 4 CPU 3.06GHz
Speed : 3.10GHz
Performance Rating : PR4118 (estimated)
Cores per Processor : 1 Unit(s)
Threads per Core : 2 Unit(s)
Internal Data Cache : 8kB Synchronous, Write-Thru, 4-way set, 64 byte line size
L2 On-board Cache : 512kB ECC Synchronous, ATC, 8-way set, 64 byte line size, 2 lines per sector
Mainboard
Bus(es) : ISA AGP PCI IMB USB FireWire/1394 i2c/SMBus
MP Support : 1 Processor(s)
MP APIC : Yes
System BIOS : American Megatrends Inc. V2.5
System : MICRO-STAR INC. MS-6728
Mainboard : MICRO-STAR INC. MS-6728
Total Memory : 2GB DDR-SDRAM
Chipset 1
Model : Micro-Star International Co Ltd (MSI) 82865G/PE/P, 82848P DRAM Controller / Host-Hub Interface
Front Side Bus Speed : 4x 135MHz (540MHz data rate)
Total Memory : 2GB DDR-SDRAM
Memory Bus Speed : 2x 168MHz (336MHz data rate)
Video System
Monitor/Panel : Iiyama A201HT VisionMaster Pro 510
Adapter : RADEON X800 Series
Adapter : RADEON X800 Series Secondary
Imaging Device : CanoScan FB630U/FB636U #2
Imaging Device : Video Blaster WebCam 3/WebCam Plus (WDM) #2
Physical Storage Devices
Removable Drive : Diskettenhet
Hard Disk : ST3160023AS (149GB)
Hard Disk : WDC WD1000BB-00CAA0 (93GB)
Hard Disk : WDC WD1200JB-00CRA1 (112GB)
Hard Disk : FUJITSU MPG3409AT E SCSI Disk Device (38GB)
CD-ROM/DVD : PHILIPS DVDR1640P (CD 63X Rd, 63X Wr) (DVD 8X Rd, 8X Wr)
CD-ROM/DVD : PLEXTOR CD-R PX-W4824A (CD 40X Rd, 48X Wr)
CD-ROM/DVD : AXV CD/DVD-ROM SCSI CdRom Device (CD 32X Rd) (DVD 4X Rd)
CD-ROM/DVD : AXV CD/DVD-ROM SCSI CdRom Device (CD 32X Rd) (DVD 4X Rd)
CD-ROM/DVD : AXV CD/DVD-ROM SCSI CdRom Device (CD 32X Rd) (DVD 4X Rd)
CD-ROM/DVD : AXV CD/DVD-ROM SCSI CdRom Device (CD 32X Rd) (DVD 4X Rd)
CD-ROM/DVD : AXV CD/DVD-ROM SCSI CdRom Device (CD 32X Rd) (DVD 4X Rd)
Logical Storage Devices
1.44MB 3.5" (A:) : N/A
Hard Disk (C:) : 149GB (101GB, 67% Free Space) (NTFS)
Xp (D:) : 112GB (2.1GB, 2% Free Space) (NTFS)
Big (E:) : 93GB (9GB, 10% Free Space) (NTFS)
Jimjimjim (F:) : 38GB (2.1GB, 5% Free Space) (NTFS)
Bologna_2 (G:) : 3.9GB (UDF)
CD-ROM/DVD (H:) : N/A
Bfv_3 (I:) : 486MB (CDFS)
Doom 3 roe (J:) : 650MB (CDFS)
Sims2ep1_1 (K:) : 650MB (CDFS)
Bf2 dvd (L:) : 1.9GB (UDF)
CD-ROM/DVD (M:) : N/A
Peripherals
Serial/Parallel Port(s) : 1 COM / 0 LPT
USB Controller/Hub : Intel(R) 82801EB USB Universal Host Controller - 24D2
USB Controller/Hub : Intel(R) 82801EB USB Universal Host Controller - 24D4
USB Controller/Hub : Intel(R) 82801EB USB Universal Host Controller - 24D7
USB Controller/Hub : Intel(R) 82801EB USB2 Enhanced Host Controller - 24DD
USB Controller/Hub : Intel(R) 82801EB USB Universal Host Controller - 24DE
USB Controller/Hub : USB-rotnav (hub)
USB Controller/Hub : USB-rotnav (hub)
USB Controller/Hub : USB-rotnav (hub)
USB Controller/Hub : USB-rotnav (hub)
USB Controller/Hub : USB-rotnav (hub)
USB Controller/Hub : USB-enhet (sammansatt)
USB Controller/Hub : Stöd för USB-skrivarport
FireWire/1394 Controller/Hub : OHCI-kompatibel IEEE 1394-värdstyrenhet
Keyboard : Logitech HID-Compliant Keyboard
Keyboard : HID-tangentbordsenhet
Mouse : HID-compliant MX310 Optical Mouse
Mouse : HID-kompatibel mus
Mouse : HID-kompatibel mus
Human Interface : Logitech WingMan Force 3D USB (HID)
Human Interface : HID-kompatible konsumentkontrollenhet
Human Interface : HID-kompatibel enhet
Human Interface : Logitech Virtual Hid Device
Human Interface : Logitech Virtual Hid Device
Human Interface : Logitech USB MX310 Optical Mouse
Human Interface : Logitech WingMan Force 3D USB
Human Interface : USB HID (Human Interface Device)
Human Interface : Internet Keys USB
MultiMedia Device(s)
Device : Audigy X YouP-PAX A4 v1.00 Audio Driver(WDM)
Device : Creative Game Port
Device : Pinnacle PCTV Stereo PAL Capture Device
Printers and Faxes
Model : Microsoft Office Document Image Writer
Model : Canon PIXMA iP4000
Model : Adobe PDF
Power Management
AC Line Status : On-Line
Operating System(s)
Windows System : Microsoft Windows XP/2002 Professional (Win32 x86) 5.01.2600 (Service Pack 2)
Network Services
Adapter : Intel(R) PRO/1000 MT Desktop Adapter #2

Thanks for your answers.
Danny: 1. Yes, I've put my memory in my brothers computer, and ran memtest there, and it came out ok, but on mine it crashes almost instantly.
2. Yea, I have 2 fans blowing into the case and one out, so airflow is good, cpu is also cool and seems to be happy ;-)
Geps: I can't say I understand all these numbers but there are som specs here as an example, Tagan TG480-U01 480W ATX
I can't imagine that this psu ain't enough, and if so.....I've been had by the dealer.

645 Ultra Memory Timings

I use 2 sticks of 256 MB Corsair XMS PC2700 CAS2. It runs great at 2.5, but XP gives me the big blue screen when I set it to 2. I've tried this with 'normal' timing and 'ultra' with one and both sticks with the same results. It will load into 98 at cas2, but won't finish some benchmarks. By the way, this is with no overclocking. RAM has heat spreaders and case is well ventilated. Any ideas?
Also, Sandra 2002 SP1 memory bench gives me 2275/2271 with my memory set at 2.5-2-2CL. Is this what most of you get? Thanks everyone!
MSI 645 ULTRA w/BIOS 1.6 from old forum
P4 1.8A
2x 256mb Corsair XMS pc2700
Tekram ultra160 dc390-u3w
IBM 36Z15 18.1 GB 15,000 RPM
SB LIVE!
MSI GeForce4 Ti4400

I had same problem...
I had 2 x 256 twinx llpt 3200 from corsair, no problem, running verry aggrssive timings and turbo timing.
added a 512 stick XLPT (faster still) and system would only boot at safe timing setting and cas2.5, with delay1T (2T)
I posted question on asktheramguy, corsairs very own and very responsive specialist, and he put it down to excessive load on the memory controller.
Also if you have different memory manufactures mixed in the slots, that's even worse, and you may not get the system to boot even after relaxing the timings
maybe lower speed 2100's and relaxd timing would be OK, but not much use with todays games
Or set memory timings to safe in bios...
So i bought another 512 3200XLPT stick and am selling the TwinX 2x256 LLPT's.
Well, I'm at 1gig at present 2 x 512 PC3200 XLPT (little over kill but fast).
With mem ratio set correctly and with my overclock this is running at about 380 Mhz (not the rated 400Mhz).
So upshot is, you'll need to get better ram, get a mached pair, and if your not bothered abour raw memory speed get something mid range cas 2.5 say....

My drive recently had to be replaced with a new one installed by Apple they reinstalled all my stuff from my time machine. Most my programs had to be updated which I managed with a little help from my friends, but the last one that I can't solve is

My IMAC OSX 10.6.8 2.8 GHz intelcore 2Duo 4GB 800 Mhz DDR2 SDRam recently had to have its hard drive replaced by apple thy actually had to give me a larger one because mine was no longer available,They also reinstalled all my programs and data from my 2 terrabite time machine back up. I got my system home and found that I had to upgrade most of my programs which I managed with a little help from my friends, but I still have one problem that I can't solve I have a Nikon Coolpix S6 that I have Been Syncing with my Iphoto since I've got it 3 years ago and now when I place it in the cradle the program reconizes it and says that it is going to start to import the new photos the little white wheel in the center of the screen starts spinning but nothing else happens. I checked all my connections and they are goog plus I even downloaded a nikon progam just to double check the camera & cradle and it works there but it wont pair off with my IPhoto.

First go to iPhoto Preferences, look in both General and Advanced tabs to make sure that things are set to import from camera into iPhoto.
Then if that doesn't help, connect the camera and open Image Capture in your Applications > Utilities folder and see if you can use Image Capture to reset the import path from the camera to iPhoto.
Image Capture: Free import tool on Mac OS X - Macgasm
Message was edited by: den.thed
Sorry John, I didn't see your post when I clicked the reply button. Dennis

Memory Timings on Neo4 Platinum???

I noticed on my Neo4, most memory settings are set to "Auto" by default.. Being I like to fool around in the BIOS, I tried setting the timings to relatively relaxed settings. The system wouldn't POST... Cleared the CMOS and tried again. This time I used the Windows based program A64 Tweaker to see what "Auto" was... All settings seemed fine, but different then what I tried....
I then went back into the BIOS and set the memory timings to what the A64 Tweaker displayed, and rebooted.... The system POSTed and I went into Windows to recheck what I had set...
Much to my suprise, the A64 Tweaker displayed about 5 settings that were different then what I had set. I rechecked this several times. ...
It must be that the A64 Tweaker is wrong, I thought,... so I reset up my Neo2 Platinum and did the same test. This time the Tweaker agrees with the BIOS, exactly.... Now I'm really confused... So back to the Neo4 to recheck the settings and the Tweaker display of memory timings...The settings were set with the system at all BIOS defaults
What I found is that many timings set in the BIOS, were different then the A64 Tweaker showed...!
The following timings come out "1 number" setting higher then the BIOS setting:
Trc
Trfc
Trrd
Trtw
The following timings come out "1 number" setting lower then the BIOS setting:
Twr
I also noticed that "Max Async Latency" is set to 6ns, but the A64 Tweaker shows 8ns....
As a sanity check, the A64 tweaker was tried on other 64 bit systems and the BIOS settings agreed with the A64 Tweaker readings, exactly ....
Has anyone had any luck setting the memory settings...?
Specs:
Neo4 Platinum
1.3 BIOS default settings
Winchester 3000 Retail HSF
PCX 5750 Video Card
WD 40Gig HDD
Tagan 480 Watt PSU

That is what I'm trying to do, but the BIOS settings and the Tweaker never agree on the 5 timings I listed above.
On the Neo2, they are exactly the same every time... I just don't understand why the Tweaker and the Neo4 BIOS don't agree... On 5 other nF3/nF4 boards they are all exactly the same...

Need a little help new to mac

Need a little help I'm new to Mac.. i have had my ibook for over a year now and i like it a lot, but some times my usb post dies on my for a couple days maybe weeks. Ill have my ipod connected and when i go to plug in a flash drive. It doesn't detect my ipod anymore and my usb port don't work. it says that they were "removed improperly" and now they are not working again..i have tried to reinstall the whole os again and that doesn't work i don't have the hardware test disk so i don't know what could be the problem i know its not the logic board is there any test i can do to it to find out the problem its an ibook late 2001... there is no reset button on it. i tried to hold in the space bar and now when i boot up i get prompt to this screen that shows the world and then a folder with a ? mark but then after a few sec it boots right up im a mess need some help

+it says that they were "removed improperly"+
You have to go to the iPod's icon on your computer (or the flash drive's icon), select it and eject it there before removing it. Otherwise, data can be corrupted and/or lost. Repeatedly removing it without ejecting it from the desktop can cause it not to be recognized any longer.
If your iBook is a "late 2001" model. It should have a reset button. Check out the chart here to make sure which model iBook you have:
http://support.apple.com/kb/HT1772?viewlocale=en_US
+i get prompt to this screen that shows the world and then a folder with a ? mark but then after a few sec it boots right up+
It's trying to find a network volume from which to boot.
Once it's booted up, go to System Preferences > Startup Disk, and select your Mac OS X startup volume. Then close System Preferences. The next time you start up, it should start up without looking for a network volume.

Little help needed on utl_file

Hi
I am trying to write a small stored procedure for recording some information to a text file, and I need a little help. However, beforehand, let me give you what I have done:
procedure create_record (order_id IN VARCHAR2) IS
l_dir VARCHAR2(10) 'c:/orders';
l_filename VARCHAR2(25) := 'orderlist';
l_datetime DATE := sysdate;
l_output utl_file.file_type;
begin
l_output := utl_file.fopen(l_dir, l_filename, 'w');
if !utl_file.fopen(l_output) THEN
utl_file.put_line(l_output, l_datetime || order_id);
utl_file.fclose(l_output);
else
utl_file.fclose(l_output);
l_output := utl_file.fopen(l_dir, l_filename, 'a');
end if;
end;
Now for questions, firstly, I am not entirely sure that the if statement for checking to see if an existing text file exists is the correct way, and would welcome some help on this, and correction.
Secondly, I need to add a second statement to the if, which if the file exists and the date on that file is the same as the system date, then to open and append some information to it, else create a new file.
Unfortunately, for me, I am not sure how to do this.
Can anyone show me how this can be done?
Thanks

Hope you can read my coding correctly.
ps: not tested
DECLARE
myFileExist BOOLEAN;
myFileLength NUMBER;
myFileBlockSize BINARY_INTEGER;
myText VARCHAR2(1000):= NULL;
myInstr NUMBER;
l_dir VARCHAR2(10) 'c:/orders';
l_filename VARCHAR2(25) := 'orderlist';
l_datetime DATE := trunc(sysdate);
l_output utl_file.file_type;
BEGIN
utl_file.fgetattr(l_dir, l_filename, myFileExist, myFileLength, myFileBlockSize);
if not myFileExist then -- file not exist
<ul>l_output := utl_file.fopen(l_dir, l_filename, 'w');
utl_file.put_line(l_output, l_datetime || order_id);</ul>
else --file exist
<ul>
l_output := utl_file.fopen(l_dir, l_filename, 'r');
LOOP
<ul>
--------------------------------------------------------------------start loop
UTL_FILE.GET_LINE(l_output,myText) ;
SELECT instr(UPPER(myText),UPPER(trunc(SYSDATE))) into myInstr FROM dual;
IF myText IS NULL THEN
<ul>
EXIT;
</ul>
END IF;
if myInstr > 0 then
<ul>
utl_file.fclose(l_output);
l_output := utl_file.fopen(l_dir, l_filename, 'a');
</ul>
else
<ul>
utl_file.fclose(l_output);
l_filename:='newfilename';
l_output := utl_file.fopen(l_dir, l_filename, 'w');
</ul>
end if;
--------------------------------------------------------------------end loop
</ul>
END loop;
utl_file.put_line(l_output, l_datetime || order_id);
</ul>
end if;
utl_file.fclose(l_output);
END;
Edited by: Lie Ching Te on 12-Feb-2010 12:34 PM
Edited by: Lie Ching Te on 12-Feb-2010 1:01 PM

A little help needed in message mapping

a little help needed in message mapping
I have to map one of the idoc header segments as many times as it occurs to each Idoc when using the split message funcionality
let us say we have the segment seg1 and there is a QUALF in it
<seg1>
<qualf>001</qualf>
</seg1>
<seg1>
<qualf>002</qualf>
</seg1>
then we use the vbeln to split the idoc into 2.
so if we have
<vbeln> 1 </vbeln>
and
<vbeln>2 </vbeln>
then 2 Idocs should be created like this
<Idoc>
<vbeln> 1 </vbeln>
<seg1>
<qualf>001</qualf>
</seg1>
<seg1>
<qualf>002</qualf>
</seg1>
</Idoc>
<Idoc>
<vbeln> 2 </vbeln>
<seg1>
<qualf>001</qualf>
</seg1>
<seg1>
<qualf>002</qualf>
</seg1>
</Idoc>
it is easy to create the segment by using createif with the QUALF field but my problem how to map the qualf twice for each idoc
Thanks.

UseOneAsMany is the function you need to use.
It takes three parameters:
1 --- The node you want to duplicated
2 --- How many times you want to duplicated
3 --- The context you want to place for it.
Regards
Liang

Hi i keep downloading the same song twice on different things, these collections and regular albums are confusing...i lost all my media and trying to get it back and now 2 of the same song is up...why cant support be a little helpful?

is Apple going bankrupt again, they seem to not wanna be bothered, is there a way to EMAIL, im not into calling and it says my calls have expired....why cant Apple be a little helpful, im a little upset with them and wanna throw my ipod touch across the room - i dont want 2 of the same songs anymore, i dont wanna be charged twice these bands are making it very difficult to remember the last album i had this stuff on....i dont know my music anymore it keeps changing

Perhaps, if you stop ranting - and stop typing in capitals (which is regarded as shouting), then you may get somewhere. But since I'm so nice...
A good place to start for help is here, in these discussions and then proceed by explaining the probelm clearly.
Let's start by crossing out anything that isn't relevant:
is Apple going bankrupt again, they seem to not wanna be bothered, is there a way to EMAIL, im not into calling and it says my calls have expired....why cant Apple be a little helpful, im a little upset with them and wanna throw my ipod touch across the room - i dont want 2 of the same songs anymore, i dont wanna be charged twice these bands are making it very difficult to remember the last album i had this stuff on....i dont know my music anymore it keeps changing
So, are we to assume that a band you like, produce albums with songs on them that you already have, on other albums?
If so, that's down to the band, not Apple. The only answer to that is that you should check for yourself whether you already have a particular song and if you do, don't buy it again. However, you should also consider that buying the full album (with a song you don't want) may be cheaper than buying the individual songs that you do want.

Little help please with forwarding traffic to proxy server!

hi all, little help please with this error message
i got this when i ran my code and requested only the home page of the google at my client side !!
GET / HTTP/1.1
Accept: image/gif, image/x-xbitmap, image/jpeg, image/pjpeg, application/vnd.ms-excel, application/vnd.ms-powerpoint, application/msword, application/x-shockwave-flash, */*
Accept-Language: en-us
UA-CPU: x86
Accept-Encoding: gzip, deflate
User-Agent: Mozilla/4.0 (compatible; MSIE 7.0; Windows NT 5.1; InfoPath.2; .NET CLR 2.0.50727)
Host: www.google.com
Connection: Keep-Alive
Cookie: PREF=ID=a21457942a93fc67:TB=2:TM=1212883502:LM=1213187620:GM=1:S=H1BYeDQt9622ONKF
HTTP/1.0 200 OK
Cache-Control: private, max-age=0
Date: Fri, 20 Jun 2008 22:43:15 GMT
Expires: -1
Content-Type: text/html; charset=UTF-8
Content-Encoding: gzip
Server: gws
Content-Length: 2649
X-Cache: MISS from linux-e6p8
X-Cache-Lookup: MISS from linux-e6p8:3128
Via: 1.0
Connection: keep-alive
GET /8SE/11?MI=32d919696b43409cb90ec369fe7aab75&LV=3.1.0.146&AG=T14050&IS=0000&TE=1&TV=tmen-us%7Cts20080620224324%7Crf0%7Csq38%7Cwi133526%7Ceuhttp%3A%2F%2Fwww.google.com%2F HTTP/1.1
User-Agent: MSN_SL/3.1 Microsoft-Windows/5.1
Host: g.ceipmsn.com
HTTP/1.0 403 Forbidden
Server: squid/2.6.STABLE5
Date: Sat, 21 Jun 2008 01:46:26 GMT
Content-Type: text/html
Content-Length: 1066
Expires: Sat, 21 Jun 2008 01:46:26 GMT
X-Squid-Error: ERR_ACCESS_DENIED 0
X-Cache: MISS from linux-e6p8
X-Cache-Lookup: NONE from linux-e6p8:3128
Via: 1.0
Connection: close
java.net.SocketException: Broken pipe // this is the error message
at java.net.SocketOutputStream.socketWrite0(Native Method)
at java.net.SocketOutputStream.socketWrite(SocketOutputStream.java:92)
at java.net.SocketOutputStream.write(SocketOutputStream.java:115)
at java.io.DataOutputStream.writeBytes(DataOutputStream.java:259)
at SimpleHttpHandler.run(Test77.java:61)
at java.lang.Thread.run(Thread.java:595)
at Test77.main(Test77.java:13)

please could just tell me what is wrong with my code ! this is the last idea in my G.p and am havin difficulties with that cuz this is the first time dealin with java :( the purpose of my code to forward the http traffic from client to Squid server ( proxy server ) then forward the response from squid server to the clients !
thanx a lot,
this is my code :
import java.io.*;
import java.net.*;
public class Test7 {
public static void main(String[] args) {
try {
ServerSocket serverSocket = new ServerSocket(1416);
while(true){
System.out.println("Waiting for request");
Socket socket = serverSocket.accept();
new Thread(new SimpleHttpHandler(socket)).run();
socket.close();
catch (Exception e) {
e.printStackTrace();
class SimpleHttpHandler implements Runnable{
private final static String CLRF = "\r\n";
private Socket client;
private DataOutputStream writer;
private DataOutputStream writer2;
private BufferedReader reader;
private BufferedReader reader2;
public SimpleHttpHandler(Socket client){
this.client = client;
public void run(){
try{
this.reader = new BufferedReader(
new InputStreamReader(
this.client.getInputStream()
InetAddress ipp=InetAddress.getByName("192.168.6.29"); \\ my squid server
System.out.println(ipp);
StringBuffer buffer = new StringBuffer();
Socket ss=new Socket(ipp,3128);
this.writer= new DataOutputStream(ss.getOutputStream());
writer.writeBytes(this.read());
this.reader2 = new BufferedReader(
new InputStreamReader(
ss.getInputStream()
this.writer2= new DataOutputStream(this.client.getOutputStream());
writer2.writeBytes(this.read2());
this.writer2.close();
this.writer.close();
this.reader.close();
this.reader2.close();
this.client.close();
catch(Exception e){
e.printStackTrace();
private String read() throws IOException{
String in = "";
StringBuffer buffer = new StringBuffer();
while(!(in = this.reader.readLine()).trim().equals("")){
buffer.append(in + "\n");
buffer.append(in + "\n");
System.out.println(buffer.toString());
return buffer.toString();
private String read2() throws IOException{
String in = "";
StringBuffer buffer = new StringBuffer();
while(!(in = this.reader2.readLine()).trim().equals("")){
buffer.append(in + "\n");
System.out.println(buffer.toString());
return buffer.toString();
Edited by: Tareq85 on Jun 20, 2008 5:22 PM

Greetings, I need a little help. I have a WRT54G Wirele...

Greetings,
I need a little help. I have a WRT54G Wireless Router, and it worked well for years with my Alcatel DSL Modem (Bellsouth/ATT). The modem went out and it was replaced with Westell Modem. When I bypass the router I have no problem connecting to the Internet, however when I connect the router--no connection. I thought it would not be a problem swapping the modem out. I am running XP with Norton Internet Security and Anti-virus. I have disabled Norton and do not believe that to be the problem. Do I have to reconfigure the router? If so, can I do it with the original install CD? (I am disabled and the original CD/instructions/box is in the attic and I cannot get it easily.) I have read several different threads, but they do not specifically address my problem. Any assistance is appreciated. Eddy

Many Westell modems are actually "modem-routers" and they use the same 192.168.1.1 address space as your WRT54G. This is the root of your problems.
Try the settings at this URL.
http://www.dslreports.com/faq/6323
Note that the "WAN" port on the BEFSR41 in the example is the same as the "Internet" port on your WRT54G.
Please let me know whether or not this worked for you.

TS1372 I was just about to about to update my iPod nano 7 from 1.0.2 to 1.0.3 . And after the complete download of the software,it says "The firmware file could not be found" A little help anyone!!!

I was just about to about to update my iPod nano 7 from 1.0.2 to 1.0.3 . And after the complete download of the software,it says "The firmware file could not be found" A little help anyone!!!

Welcome to Apple Discussions!
Take a look at these two articles. The error messages are not the same, but they may help...
http://docs.info.apple.com/article.html?artnum=304309
http://docs.info.apple.com/article.html?artnum=301267
If not, post back.
btabz

Need a little help with dial setup on CME

I've got a CME I'm using for testing and I think I need a little help figuring out the proper config to get the system to accept numbers I dial and have those numbers be passed on to an Avaya system (including the leading 9 for ARS in Avaya) via H.323 IP trunks.   I have it working well for internal 5 digit extension calls across the H.323 trunks and I also have it working well for some types of outside calls that gets passed on to the Avaya and then the Avaya dials the call out to the PSTN.   My only real problem is, I can't figure out how to correctly configure CME to examine the digits I'm dialing and only send the digits once I'm finished dialing....not as soon as it sees an initial match.
What's happening is this. I can dial local numbers in my area as 7 digits or 10 digits. The phone company doesn't yet force us to dial area code and number for local calls (10 digits). I can still dial 7 digits.   But...if I put an entry in CME that looks like this....
(by the way, the 192.168.1.1 IP is not the real IP address, that's just an example, but the rest of this entry is what I really have entered in CME)
dial-peer voice 9 voip
description Outside 7 Dig Local Calls Via Avaya
destination-pattern 9.......
session target ipv4:192.168.1.1
dtmf-relay h245-alphanumeric
no vad
...Then it will always try to dial out immediately after seeing the first 8 digits I dial (9 plus the 7 digit number I called)...even though I have a speicifc entry in the system that accounts for calls to 9 plus area code 513. I would have assumed that if I put the specific entry in for 9513....... it would see that and wait to see if I was actually dialing something to match 9513....... instead of 9.......   Understand what I mean?   Because 9513....... is more specific than 9....... but it still tries to send the call out immediately after seeing the first 8 digits I dialed.
dial-peer voice 9513 voip
description Outside 10 Dig Local Calls Via Avaya
destination-pattern 9513.......
session target ipv4:192.168.1.1
dtmf-relay h245-alphanumeric
no vad
...BUT...here's the interesting thing. If I trace the 10 digit call in Avaya, I see that the number being presented to the Avaya PBX is only the first 7 digits of the number....not the full 10 digits...BUT I see a few more of the digits I dialed (like the 8th and 9th digits) after the call is already setup and sent to the PSTN. It's like the CME is trying to send the rest of the 10 digits I dialed, but at that point it's already too late.   It setup the call as a 7 digit call (9 plus 7 digits), not 10 digit like I wanted.
I'm more familiar with how to setup dialing in the Avaya via ARS. My background is Avaya, not Cisco, so this dial-peer config is a little difficult for me until I understand the reasoning of how it examines the numbers and what I should do to make it wait for me to finish dialing....or to tell the system that what I'm dialing will be a minimum or a certain amount of digits and maximum of a certain amount of digits, like the Avaya does. I just need some pointers and examples to look at :-)   I think I've almost got it....but I'm just missing something at the moment.
Just so you understand, the call flow should be like this: Cisco phone registered to CME > CME to Avaya via H.323 trunks > Avaya to PSTN via ISDN PRI trunks connected to Avaya. I have to be sure I send the 9 to the Avaya also, because 9 triggers ARS in the Avaya.
Thanks for your help

Here is a good document that explains how dial-peers are matched in the Cisco world:
http://www.cisco.com/en/US/tech/tk652/tk90/technologies_tech_note09186a008010fed1.shtml#topic7
In your case, it is variable length dial plan you are trying to implenent. To fix it, you need to add a T to force the system to wait for more digits to be entered if there is any.
dial-peer voice 9 voip
description Outside 7 Dig Local Calls Via Avaya
destination-pattern 9.......T
session target ipv4:192.168.1.1
dtmf-relay h245-alphanumeric
no vad
dial-peer voice 9513 voip
description Outside 10 Dig Local Calls Via Avaya
destination-pattern 9513.......
session target ipv4:192.168.1.1
dtmf-relay h245-alphanumeric
no vad
You can also configure the inter-digits timeout using the command timeouts interdigit under telephony-service.
Please rate helpful answers!

Need a little help.... not major....but am unsure I have...

Need a little help.... not major....but am unsure I have the 2.4 GHz Wireless-G Broadband Router Model WRT54G version 2 I had bought some time ago (over year and a half) and never really had it hooked up since I have been moving from place to place. Now that I'm retired and staying in one place I'm ready to set up. I find myself having "several" power adaptors and not sure which is the correct one. Can anyone tell me if all the broadband routers had the Linksys name and/or logo on them? None of the adapters I have do. I want to use a proper adapter so as not to damage....are there any specs that would be helpful so that one of these adapters would work? Also I'm running WindowsXP Sorry to bother you folks with a dumb question as I'm sure there are others with far more important questions and concerns. Although I can't tell other than the end going into the unit fits, I do have one Class 2 Transformer which might be the one it's about 1 1/2 inches thick, about 2 inches tall with following written information: Model 49-12-1000D CUI Inc Input AC 120V 60Hz 20W Output DC12V 1000mA Appreciate any help you can give.....I believe my unit is an older one based on version so there may have been a "fatter" adapter then than now.

The power adapter output should be 12V, 0.5A(so 6W power rating)

A little help re: memory timings.

Similar Messages

Maybe you are looking for