A problem with the P35 Neo2-FR

Greetings
Firstly I'm new to this forum and by the looks of it its not based in Europe so you're all probably asleep right now.
Anyway, I am having trouble getting this motherboard, Neo2-FR, to boot at all and nothing but a blank screen. No BIOS, no splashscreen, nothing.
When I short the power switch it turns on, then off, then on and the LEDs go through the sequences of red/green until it reaches green, green, red, green and stops. The red CMOS LED is lit constantly, the blue PCI-E LED is lit, LED 13 (PCI slot 1) flickers constantly but the PCI slots are empty.
I've tried using 4 sticks of RAM, 2sticks of RAM and 1stick of RAM. It makes no difference. The FSB has been set to 200, 266 and 333 to no effect. I have tried plugging in a floppy drive, CD-ROM and harddrive all to no effect. I have tried pressing the CMOS switch, shorting the power, shorting the reset switch and patience.
I'm very thorough and usually something is faulty when I can't fix it.
Whats wrong with it? Is LED flickering a bad sign?
edit: this board should boot without a BIOS update for 45nm chips
Thank you for all your support
-MSI P35 Neo2-FR (UK) revision A7345 IMS 150 and BIOS unknown
-Intel socket 775 E8400 "Wolfdale" stepping C0 Retail
-DDR2 Crucial Ballistix PC5300 CAS 3 1Gb x4
-Ati HD3850xt 512MB DDR3
-Enermax Noisetaker 600w 3.3V 34A 5V 34A 12V1 18A 12V2 18A
-Hard Drives: Not available
-Optical Drives: LG 4123B DVD-RW
-Operating System - not installed
Here is a picture:
http://homepages.nildram.co.uk/~zen12084/Storage/helpme.jpg

That's definetely a new one...
I would still flash to the correct BIOS with the CPU microcode for your Wolfdale. That BIOS would be v1.6: >>Link<<
Flash the BIOS with our USB flashing tool: >>MSI Forum HQ USB Flashing Tool<<

Similar Messages

  • Problem with new P35 Neo2 Build

    Ok, I had a Gigabyte DS3 rev. 1.0 before and I narrowed it down to the MB failing, which I've heard alot of before. So I bought a MSI P35 Neo2 (rev 1.1, Bios 1.1) to replace it and just put it back together with the following parts:
    C2D E6400, Mushkin 2GB XP PC2-6400, 2 Samsung 250GB Sata HDDs. On first boot up it went fine and I was in the BIOS and set it up, then booted into Windows Vista. Just today I tried to start the PC but nothing, so I cleared the cmos and it then started up, but hung. The leds in the group 1, 2, 3 & 4 are all red. In the manual it states "System Power On, The D-LED will hang here if the processor is damaged or not installed properly".
    Am I to assume my cpu is toast now?

    So I swapped my Q6600 into my P35 Neo2 and it still has the 4 red leds! I also swapped out the video card for my HD 2600XT, and the power supply with my Seasonic SS-500HT 500W PS, and ram (OCZ PC6400 2GB) and still 4 red leds. I also tried the C2D E6400 in my Abit Quad GT and it boots up fine. I've pretty much narrowed it down to the motherboard I guess. What are my options at this point?
    Thanks
    ***Update***
    Well, I just figured it out. When I swapped power supplies I forgot to plug the 8 pin connector into the MB. There is nothing wrong with my CPU or my MB.
    The stats on my other P/S (SS-500HT are, +3.3v - 30A, +5.0v - 30A, +12V1 - 17A, +12V2 - 16A., not alot more than my other P/S, but just enough to get it to work??
    Anyway, I am going to get a new P/S. I am looking at either the Corsair VX550, I can get it for $84 Cdn, plus a $15 MIR, which you probably never get anyway. How about PC Power & Cooling Silencer 610W EPS12V? It's more money, but I hear good things about their P/S's??
    Is it better to go with a large single 12V rail as apposed to multiple lower rails?
    Thanks for your help.

  • So is everyone having temp problems with the K8N Neo2??

    like 50'C-60'C idle CPU temp that includes a good quality heatsink w/AS5???

    Well the XP-120 technically doesn't fit....  and the fan pushes about 80CFM
    When you install the XP-120 one way, it obstructs the AGP slot by about 3mm.  If you rotate it, it's obstructed by some resistor caps and covers up DIMM's 1+2.
    So unlike the thermalright.com compatibility list, you have to run RAM in DIMM's 3+4 and tilt the cap for an EXTREMELY TIGHT fit, or do what I did and dremel off 4 fins and 6mm of heat pipe.
    I capped the pipes with some silicone, since pipes need constant internal pressure to function, but... that leads me to another question as to why the heatpipes are filled with air and not a fluid when air is probably the worst thermal conductor evar.
    Theoretically if that XP-120 mod job some how compromised the thermal integrity of the entire heatsink ( i have no idea how ), then the Zalman should fix that.  Then the problem is as to why my BIOS system temperature @ startup is 30'C and when I load up MSI Core Monitor, it lists it at about 10'C.
    Something is definately screwed up.  It's either a BIOS error, my XP-120 heatsink (doubt it), or defective temp sensors and I need to RMA it.
    I also have a suspicion that by default, the BIOS reports the temperature coming off the Winbond 2 Diode instead of the Winbond 2N3904 sensor.  Temperatures are about 8-10 degrees 'C hotter than the system temperature when reading the 2N3094, but then again I don't know which is the correct sensor to be using or any way to verify.

  • Having Problems With The Neo2 ? Read This!!!!

    Hi,
    i just bought a neo2 motherboard, with a p4 2,6 HT and 512 mb Kingston hyper ram ( 2 peaces of 256, else it won't use the dual bandwith :D)
    In the beginning everything seemed fine, until i got some sudden reboots and other vague stuff. I read it could be the SB audigy messing things up. I removed the card and windows Xp pro runs fine now. no more sudden reboots or explorer not resonding crashes.
    But, i still had problems with games crashing. I got reboots. After i set the "automatic reboot after crash" to false, i got blue screens or lock-ups in my games.
    I wondered what it could be. Then i started to put my videocard ( a radeon 9700 pro 128 mb) in agp 4x mode instead of agp 8x! Now my games run without crashes, but benchmarks are not that high. 4780 marks with 3dmark 2003.
    I think i will send msi and Ati a mail concerning this problem. I don't know if it is PSU related. Maybe the videocard demands a little more power in agp 8x mode.
    Well, having probs with you're NEO2 ??
    remove the sb Audigy and turn the agp back to 4 using smartgart ( it's located in you're display settings screen ).
    First i tought it was a PSU related problem, because i swapped my 350 Watt enermax with a Q-tec 400 watt psu. The 400 watt PSU died while i was gaming. Maybe the enermax is the better PSU :D So, it could still be a PSU related problem. Maybe the agp 8x settings demands a lot more from you're psu. Anyway, i'll receive a 550 watt Antec PSU soon, so i can check this out....
    Btw. I cant run the motherboard in anything better than "slow" mode. In all other modes Xp won't boot. I haven't tryed it since the AGP is at 4X, but i don't think it will matter.
    Regards,
    Welcome to the real world NEO :D

    Ok.....
    i raised the memory voltage setting in the bios from 2.65 to 2.8 and the agp voltage from 1.5 to 1.7
    Everything seems fine, but games crash back to the desktop now without an error message or the either lockup.
    Whatever i do, i can't make the mobo crash in anything but games!
    Btw. the following message caught my attention, when i ran f1 2002 with directx 8.1. Since i have directx 9, i haven't seen it anymore. Maybe because the ati-drivers are made for directx 9....
    // Watchdog Event Log File
    LogType: Watchdog
    Created: 2003-10-04 02:02:53
    TimeZone: -60 - West-Europa (standaardtijd)
    WindowsVersion: XP
    EventType: 0xEA - Thread Stuck in Device Driver
    // The driver for the display device got stuck in an infinite loop. This
    // usually indicates a problem with the device itself or with the device
    // driver programming the hardware incorrectly. Please check with your
    // display device vendor for any driver updates.
    ShutdownCount: 9
    Shutdown: 0
    EaRecovery: 1
    EventCount: 2
    BreakCount: 2
    BugcheckTriggered: 1
    DebuggerNotPresent: 1
    DriverName: ati2dvag
    EventFlag: 1
    DeviceClass: Display
    DeviceDescription: RADEON 9700 PRO
    HardwareID: PCI\VEN_1002&DEV_4E44&SUBSYS_00021002&REV_00
    Manufacturer: ATI Technologies Inc.
    DriverFixedFileInfo: FEEF04BD 00010000 0006000E 000A18EA 0006000E 000A18EA 0000003F 00000008 00040004 00000003 00000004 00000000 00000000
    DriverCompanyName: ATI Technologies Inc.
    DriverFileDescription: ATI Radeon WindowsNT Display Driver
    DriverFileVersion: 6.14.10.6378
    DriverInternalName: ati2dvag.dll
    DriverLegalCopyright: Copyright (C) 1998-2002 ATI Technologies Inc.
    DriverOriginalFilename: ati2dvag.dll
    DriverProductName: ATI Radeon Family
    DriverProductVersion: 5.2.3790.2
    I wish i had another videocard to test. My radeon 9700 pro is getting suspicious...
    Regards,
    The real world

  • Problems with msi p35 neo 2

    Default problems with msi p35 neo 2
        pc works fine when using windows and the net and emails
        only when using 3d mark or games do i ever get problems
        just help in getting the hole story 6 months ago got a msi neo2 install all my old components core 2 duo 4 gig ram form a diffrent board works fine but never used it playing games just used for the net and email shoping seamed to work fine but
        tryed playing a game 2 months later command and conquer 3 pc was some times freeze or graphics artefacts on screen assumed vga card faulty got another graphics card geforce 8600gts installed still the same in the last month got round to playing with the pc again and installed new g7 780 watt power supply and ati hd 4870 graphics card
        now i can use 3d mark some times it will go through once or just freeze or 3d mark stops the test
        temps on the board (from msi dual core center temps cpu 33oc system 47oc)
        memory voltage 2.1
        any one know the settings for the ram
    more details you need
    System Details
    MotherboardEdit Value
        msi p35 neo2 fr
    Motherboard BIOSEdit Value
        latest
    CPUEdit Value
        core 2 quad 6600
    CPU Overclock SpeedEdit Value
        none
    CPU HeatsinkEdit Value
        standard intel that come with cpu
    CPU Idle TempEdit Value
        N/A
    CPU Load TempEdit Value
        N/A
    MemoryEdit Value
        ******* xms2 2x2 gb ddr2 part no cm2x2048 6400c4dmx
    Memory VoltageEdit Value
        N/A
    Video Card(s)Edit Value
        ati hd4870
    Video Card SpeedEdit Value
        N/A
    Sound CardEdit Value
        onboard
    PSUEdit Value
        g7 780 watt power extreme
    Hard Drive(s)Edit Value
        mator dimondmax 21
    Optical Drive(s)Edit Value
        N/A
    Other CoolingEdit Value
        3 80mm fans 1 frount 1 back 1 side
    ModsEdit Value
        N/A
    Operating SystemEdit Value
        windows 7

    Quote
        ******* xms2 2x2 gb ddr2 part no cm2x2048 6400c4dmx
       Quote
    memory voltage 2.1
    Make sure that the memory timings are not set to 4-4-4-x but that they are set to the defaults values (5-5-5-x).  Also ensure, that the memory clock speed is not set to anything higher than 400 MHz (=DDR2-800).  The voltage at these settings should not need to exceed 1.95V.  So please lower it accordingly.  In case the freezes still occure, please run memtest86+ to check your memory for errors.
    Quote
    msi dual core center
    Please get rid of that tool for all further tests.  Uninstall it completely from your system as it is known to cause crashes and freezes on its own terms when running.

  • VCORE PROBLEMS WITH MSI P35 NEO F

    To see if I can help or at least explain what's happening, buy a MSI P35 NEO F for using a quad, the topic is as follows handling vcore is rare
    First thing I can not put less voltage that the cpu brings default, second what happens next if bios setting 1.3250 vcore for Quad, once in both windows everest, cpuz, like others programs tell me that this placed on 1.40 vcore which is excessive for the speed at which the quad, this is so in this mobo? Their story that was installed version 1.20 bios which handled vcore%, the upgrade to version 1.40 and is now handled in decimals (numbers) vcore, but still the problem
    You pull more vcore which setting in bios and if you want to download the vcore eg put 1.26 vcore not let you because it takes the vcore default of cpu minimum.
    i'm  not crashing or problems with the temperatures, but nobody likes to have more vcore's necessary.
    Wonder because being rookie of this mobo, maybe there's some bios version that fixes this bug or someone knows something else, thank you guys
    C2Q Q6600
    2 X 1GB G.SKILL 6400
    PSU 550 MODULAR TOPOWER
    -- SORRY FOR MY ENGLISH --

    You can slap 1.6v in that CPU and temps won't rise that much.
    Core 2 Duo/Quad operates @ 1.250-1.425, anywhere in between those values is perfectly stable for Intel stock cooler and frequency.
    Absolutely nothing to worry about. But if you want to complain about >1c I really can't see the sense in that.

  • A few bios problems with my 915p Neo2 platinum board

    I'm wondering af anyone here can help me.
    I just got a new system and a friend of mine helped set up the bios for me, afterwards he failed to tell me how he had configured the bios (my first big mistake).
    Since the buidling of the system there have been 3 short beeps at the beginning of startup. I was told that it was a warning system of some sort and when i looked it up, the informations pointed towards a problem with the RAM.
    I ran memtest86 and it found no problems with the RAM, so i contacted the site i bought the parts from and they suggested i reset the bios.
    I did so and the beeps remained, but my DVD and DVD-writer drives arent being detected anymore.
    I took my PC around to another friends house with only his keyboard and monitor connected. The beeping had stopped before we changed anything. Bringing it back around to my house resulted in the beeping returning.
    From this i gathered that the only things different may have been his power source and the peripherals i have attached to the back of the case. (speakers, printer, kb/m, etc)
    Going by the manual map, my 2 HDDs are connected as slave/master in IDE port 1 and my two DVD drives are connected to the yellow IDE port that is closest to IDE port 1 (it's either IDE 2 or 3, the map isnt too clear on which is which).
    Long story short, can anyone help me in identifying the source of the beeps and their meaning, an optimum setup for my bios and how to get my DVD drives to work.
    Thanks in advance to anyone who can help me. I'm fairly new to building computers and my friends are the type to suddenly become unavailable as soon as a problem arises.
    edit: just noticed i missed the spec description part menitoned in the rules.
    MSI s775 915P-Neo2-Platinum
    Version 1.4 of bios
    Pentium 4 540 LGA775 3.2GHz
    Corsair VS 1GB DDR2 240 pin RAM
    256 MSI PCI-express GF6800GT, latest drivers
    600W 3XS-EzCool PPFC
    Western digital WDC WD1600JB-00EVA0 (160GB) (master)
    Seagate U series 5 HDD ST340823A (40GB) (slave) Both on IDE slot 1
    Liteon DVD-ROM (spec unavailable)
    MSI 4x DVD-RW +/- (part no: G57-CB00243, this is all i could find on this part form the box)
    Sound Blaster Audigy
    Windows XP SP2
    second attempt at clearing up the garbled mess from above.
    Motherboard is making 3 short beeps on startup. Indication of a problem with memory. I've established that it's something external that causing the beeps as the memory has checked out fine with memtest86. Hence i will be checking all the attached devices.
    I was guided to reset the bios in an attempt to clear up this problem above. Doing so has resulted in my bios being unable to detect my DVD drives.
    My DVD-drives are connected to IDE port 2/3 (manual is unclear on which is which).
    Everything was in working order (with the exception of the beeping) before the bios was reset but due to my lack of knowledge/involvement with the original configuration of the bios, i'm at a loss as to how to fix it.
    If anyone could recommend me any updates for the bios, or could advise me on how to configure my bios accordingly to the parts i have i would be most appreciative. Also, if osmeone would be abel to shed some light on the beeping issue i would be thankful also.

    Quote
    Originally posted by Danny
    The board uses a Via raid controller for the IDE 2 and 3 channels, and you do have that enabled.
    Under SATA devices configuration you should select Enhanced instead of compatible. But this should effect your problem.
    I see there is a 1.5 bios released that mentions the via controller
    http://www.msi.com.tw/program/support/bios/bos/spt_bos_detail.php?UID=601&kind=1
    Maybe someone with this board will pitch in and help.
    I saw this and was wondering if i should install it. It would be the equivelent of resetting the bios again wouldnt it? So it wouldnt be that much of a step back from where i am at the moment and it might be able to sort my IDE problems.

  • I just order 8 calendars from iPhoto and they came to me fine. Now I need to order two more but when I go thru the process I get a message  saying:unable to assemble calendar. There is a probleme with the photo with the file name"(Null)"   more........ .

    Would someone be able to explain to me the following issue with Iphoto?
    I ordered 8 same calendars for my soccer team and received them fine. Although a couple of pictures on it are a little off (out of focus). I need to order two more of the same calendars but when I go thru the process ireceive an error message saying:
    "Unable to to assemble  calendar" There is a problem with the photo with the file name "(Null)" The full resolution version of this photo either cannot be located or is corrupt. Please replace this photo or delete it from your calendar.
    How can  I fine this "corrupt" photo? How did it go thru with the first batch of calendars but won't go thru now?
    Thank you for your help.   

    Apply the two fixes below in order as needed:
    Fix #1
    Launch iPhoto with the Command+Option keys held down and rebuild the library.
    Since only one option can be run at a time start
    with Option #4 and then #1 as needed.
    Fix #2
    Using iPhoto Library Manager  to Rebuild Your iPhoto Library
    1 - download iPhoto Library Manager and launch.
    2 - click on the Add Library button, navigate to your Home/Pictures folder and select your iPhoto Library folder.
    3 - Now that the library is listed in the left hand pane of iPLM, click on your library and go to the File ➙ Rebuild Library menu option.
    4 - In the next  window name the new library and select the location you want it to be placed.
    5 - Click on the Create button.
    Note: This creates a new library based on the LIbraryData.xml file in the library and will recover Events, Albums, keywords, titles and comments.  However, books, calendars, cards and slideshows will be lost. The original library will be left untouched for further attempts at fixing the problem or in case the rebuilt library is not satisfactory.
    OT

  • I can not upgrade to quicktime 7.7.3 for windows vista.  Error message says there is a problem with the program installer.  Any clue as to how to get around this.

    I can not download quicktime 7.7.3 for windows vista.  The error message says that there is a problem with the windows installer.  Any clues?

    The error message says that there is a problem with the windows installer.
    What's the precise text of the message, please? (There's a few different ones I can think of that you might be getting.)

  • I have a problem with the sync between iTunes and ipad2. I can not see the files in iPad. Help me please.

    I have a problem with the sync between iTunes and ipad2. I can not see the files in iPad. Help me please.

    Cannot see what files ? Music (synced music should appear in the iPod app), films/TV shows (Videos app), documents ... ?

  • Is anyone having a problem with the new iPad (Gen. 3) not staying connected to the charger? It seems to ALWAYS get jiggled loose and no longer be charging. My iPad 1 has no issue but I can't browse Internet w/o new iPad unplugging. Horrible!

    I notice that my new IPad (3rd generation) will not stay connected to the power cord at all, I'm not exagerating, if I plug it in and browse the Internet without fail it will become unplugged and I will have to push the plug back in (Ba-beep). Ive actually grown to despise that sound when you plug your iPhone or iPad in because it reminds me of how much money I spent on something that PHYSICALLY will not charge while I'm using it.
    I know the problem with it holding a charge while in use, I get it, the screen is amazing and it takes a lot to run the display, however, it is unacceptable to me that I can't even keep the thing plugged in while I'm using it. I can not even leave it on my Cal King bed overnight because I will wake up in the morning to find that the plug has been jiggled loose in a corner, so it's still attached but not making a connection thus not being charged. 
    I love the 4GLTE from Verizon and I love the iPad, but I'm actually using my 1st generation IPad while I am at home so I can leave my new $900 iPad on a table to charge free of incident so I can use the 4G while I'm away from wifi during the day. I have been getting more upset about this because I can not even use the Griffin extended cord to charge the iPad and be far from the plug because only the original apple sync/charge cord will have a better shot at staying in. Absolutely none of my non apple cables will stay in the iPad 3 while having it in my hands.
    The plug is at an angle, unlike the first iPad, not sure about the iPad 2. Please let me know if they have same issue.
    If anyone else is having this problem with the Gen 3 iPad please let me know because I'm tempted to do something about it with apple and I'm hoping that I just for some reason have a bad cable receiver or something and maybe I can get a replacement and enjoy the iPad as I had expected to. There is no reason why I should be even using my first iPad and I have friends that want to buy it but I am not selling it because I'm unable to sell it because I can't handle the new iPad while it's plugged in, that is ridiculous if it's a common issue so please let me know!

    Thanks for the swift reply, I have been looking online and a loose plug seems to be somewhat of an issue with many, I hope mine is actually a problem and not what others are experiencing. It's taken me this long to even reach out for the simple fact I HATE being a complainer but this is just horrible.
    Do you have an iPad 3 as well? And is yours not experiencing any issues close to mine?
    Thanks again!

  • Is anyone having problems with the battery heating up and draining the power?  Mine has been doing this for about 2 months now.

    Is anyone having problems with the battery heating up and draining the power?  Mine has been doing this for about 2 months now.

    This is a major problem with Lollipop, but yo said it started 2 months ago.   Several people have fixed problem by removing FaceBook And Face book messenger and then re loading the apps again.   You might want to clear your cache before reloading.  Not sure this is your problem, but worth a try.  Good Luck

  • I have upgraded Apple Aperture from version 2 to version 3 and I'm having a problem with the "Highlights and Shadows" adjustment. According to the user's manual, I should have access to an advanced disclosure triangle which would allow me to adjust mid co

    I have upgraded Apple Aperture from version 2 to version 3 and I'm having a problem with the "Highlights and Shadows" adjustment. According to the user's manual, I should have access to an advanced disclosure triangle which would allow me to adjust mid contrast, colour, radius, high tonal width and low tonal width.
    If anyone has any suggestions as to how to access this advanced section, I'd be most grateful.

    Hi David-
    The advanced adjustments in the Highlights & Shadows tool were combined into the "Mid Contrast" slider in Aperture 3.3 and later. If you have any images in your library that were processed in a version of Aperture before 3.3, there will be an Upgrade button in the Highlights & Shadows tool in the upper right, and the controls you asked about under the Advanced section. Clicking the Upgrade button will re-render the photo using the new version of Highlights & Shadows, and the Advanced section will be replaced with the new Mid Contrast slider. With the new version from 3.3 you probably don't need the Advanced slider, but if you want to use the older version you can download it from this page:
    http://www.apertureexpert.com/tips/2012/6/12/reclaim-the-legacy-highlights-shado ws-adjustment-in-aperture.html

  • HT4864 I am getting a triangle with an exclamation point next to my inbox...it says: There may be a problem with the mail server or network. Verify the settings for account "MobileMe" or try again.  The server returned the error: Mail was unable to log in

    I can send but cannot recieve email
    This is the messege I am gewtting:
    There may be a problem with the mail server or network. Verify the settings for account “MobileMe” or try again.
    The server returned the error: Mail was unable to log in to the IMAP server “p02-imap.mail.me.com” using “Password” authentication. Verify that your account settings are correct.
    The server returned the error: Service temporarily unavailable

    Also if I go to system preferences accounts and re-enter the password it fixes the glitch sometimes.

  • Problems with the O2 blackberry data package on my Curve 3G.

    I have already informed O2 about this but they claim that I should be used the blackberry support services, but nothing there helps me!
    I got my Blackberry Curve 3G on September 9th this year and I put on the Blackberry Data Package bolt-on onto my phone on September 16th. I then received a text to say they've taken £5 from my credit and it will be up and running in the next 24 hours. Its now September 19th and my BBM is not working at all and I am extremely upset with the services and behaviour I have received from both O2 and Blackberry.
    Is there any way you can help? If this fails, I shall be forced to go back to the shop from where I got my Blackberry from and ask for their help.
    Many thanks, Jade.

    Can a bubble whistle Problems with the O2 blackberry data package on my Curve 3G.? The seat matures in your oar. The lad ices the pursuing method inside a resident. A judge spins against the vendor! The rose wows the hello. 
    filipina heart

Maybe you are looking for

  • Safari 3 Quits and Quits and Quits

    Installed 10.4.11 and got Safari 3 which quits at the slightest notion. For example when more than one window is open and I go to close one it quits altogether. Also if I voluntarily quit the app I always get an error message informing me that the ap

  • Aspect Ratio Scripting

    I am trying to author a dvd with 16:9 and 4:3 letterbox video & menus. I want the DVD to check the player to see whether the aspect ratio is set to 4:3 or 16:9. This works in all of the set top DVD players I have tried it in(presuming the player and

  • Information space creation error in BOBJ Explorer

    while creating the information space i am getting the following error Failed to retrieve the data source details. The creation of the data source object tree failed. Cannot perform this operation: no valid license found Looks like a license key issue

  • How do I print a list of just albums?

    I want to print a simple list of albums.  File->Print is almost what I want, but it prints a separate line for every artist on compilation albums.  I want one and only one line for each actual album.  Is there any way to do this? The closest answer I

  • Two ePub Questions

    Hello, I am formatting a novel to epub format. Everything has gone perfectly using character and paragraphy styles, etc. My two questions are as followes: 1. I've used the first page of the document to be the book cover without problem, however, wher