A question about performance of envy 15t-j000

The windows 8 experience index of my ENVY 15 is 5.0, which is the subscore of desktop graphics performance.
However, I found that the index shoulde be higher because the artical on http://www.theinquirer.net/inquirer/review/2290017/hp-envy-touchsmart-15-review/page/3 shows that the total index should be 5.9 with 6.6 on desktop graphics performance. The tech spec of my computer is the same with the one in that article. Therefore, is there something wrong with my computer, for example, the driver for graphic card is not installed properly?
Hope someone can provide me a solution. Thanks a lot.

Not if everything else works fine...
Sounds like drivers possibly need an update.

Similar Messages

HP ENVY 15t-j000 Quad Edition Notebook PC - white screen

HI,
I have HP ENVY 15t-j000 Quad Edition Notebook PC. Recently i started noticing one issue on my laptop. I of...
Please Help!!!

Hi @HPENVY15t-j000 ,
Thank you for visiting the HP Support Forums and Welcome. I have looked into your issue about your HP ENVY 15t-j000 Quad Edition CTO Notebook PC and issues with a white screen just appearing. This is usually caused by and incompatible driver or software that was installed. Here is a link to help with a white screen issue.
You can do a system restore. System restore will help if something automatically updated and did not go well on the Notebook.
When performing a System restore please note remove any and all USB devices. Disconnect all non-essential devices as they can cause issues.
Thanks.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom to say “Thanks” for helping!

Is there a way to set up a secondary monitor using an Envy 15t-j000 touchscreen with Windows 8

When I purchased my laptop, I was told that I could use a secondary monitor to view multiple documents, spreadsheets, websites, etc. I was also told that there would be a connection on the laptop, but there wasn't.
This question was solved.
View Solution.

Hi Phoenix,
I think you might enjoy reading this article:
What is the Difference Between HDMI and DVI? Which is Better?
Below is a short article about each type of connection: VGA, DVI, HDMI
Essentially, what you get, how much hassle you go through to understand and make a choice, is based on what you expect from the connection. VGA is low-res, dependable, and has been around the longest of the three types.
Decide Between VGA, DVI, and HDMI for Your Monitor Connection
I have not had any problems with any monitor when trying to connect it to Windows 8 -- the underpinings to Windows 8 are built from Windows 7. My experience: If the Monitor will connect to one, it should work on the other.
Some issues I have had with monitor connections include:
Nvidia graphics on a Win7 machine that had to be down-reved to work with one monitor (circa 2010?)
Irritating issues with the screen aspect ratio on a monitor that is forced to be connected to a system with a different native resolution than that of the monitor -- Do-able, just ps-ant irritating
Switching from one system to another when the monitor is connected to two separate notebooks that are up and running at the same time -- the "switch" is more seemless on some monitors than with others
Note that none of these issues are "show stoppers" for my purposes: I am not a gamer.
=====================================================================================
3 matches found for Envy 15t-j000
Select the model of your system below. You will find webpages for Software and Drivers, How-to information, manuals, and helpful advice on how to use your system and how to solve issues when they arise.
Please select one below:
HP ENVY 15-j000 Select Edition Notebook PC series
HP ENVY 15t-j000 Select Edition CTO Notebook PC
HP ENVY TouchSmart 15-j000 Select Edition Notebook PC series
HP ENVY TouchSmart 15t-j000 Select Edition CTO Notebook PC
HP ENVY 15-j000 Quad Edition Notebook PC series
HP ENVY 15t-j000 Quad Edition CTO Notebook PC
Happy Computing!
Kind Regards,
Dragon-Fur

ENVY 15t-j000 Quad Edition Hard Drive Thickness

I'm looking to replace the hard drive in my ENVY 15t-j000 Quad Edition with an SSD. HP's site currently does not list the thickness the the preinstalled hard drive. I would prefer to get an ssd that does not leave any extra unused space in the computer. What is the thickness of the hard drive installed in the ENVY 15t-j000 Quad Edition so I can upgrade to an equally sized ssd? Thank you.
This question was solved.
View Solution.

Hi,
It's very safe to use 7mm thick, as mentioned in my first reply.
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Replace HDD with SSD for HP ENVY 15t-j000 Quad Edition Notebook PC

I'd like to buy a HP ENVY 15t-j000 Quad Edition Notebook PC and a HP v300a 120GB SATA Solid State Drive with Upgrade Kit.
Now the SSD has a 7mm thickness.
My question is if I can replace the HDD with this SSD? How thick is the HDD bay in the laptop.
If it's more than 7mm will the SSD move inside it?
Thanks
This question was solved.
View Solution.

Hi,
The old HDD on your machine is a bit thicker but with at least 4 screws I don't think new SSD will floating around in the case. I actually put new SSD in one of my laptop (not HP) and no problem BUT I don't move this laptop around. If needed, blue tac may help.
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Hp envy 15t j000 quad edition ssd upgrade: what to know

Hello everyone so im going to buy an hp envy 15t j000 quad edition for school and was looking online to see what i can upgrade on it to make it faster. Im not very knowledgable with computers so i need lots of help! While doing so i found out the hp comes with a hard disk drive (hdd) and that these are prone to damage over time and dropping, moving, ect. I learned that solid state drives (ssd) are prefered and can make the computer significantly faster and wont be as vunerable as the disk drive. Im upgrading the envy with the NVIDIA GeForce GT 740M Graphics with 2048MB of dedicated video memory, 15.6-inch diagonal Full HD BrightView LED-backlit Display (1920x1080), and the 12GB DDR3 System Memory (2 Dimm) option. Will any of this affect my swapping of the hdd? I also was wondering why the 8gb ddr3 system memory (2dimm) didn't affect the price for switching to the 12gb option.There isnt a difference right? also would the 24gb accelrated cache be of any use? For my last question i think i heard that i would need to clone or buy another copy of windows 8 to put on the new ssd. will there be any problems doing this? Am i in for a headache?

Pepe999
I went on to Tom's Hardware to looking into the 16GB memory.. there is a recent report where adding 16 gb-ddr3 ram.. will increase the life of a SSD drive by 63% compared to 4gb.. here is the link.. thought it was interesting and supported my thinking in reducing the number of HD writes.
http://www.tomshardware.com/reviews/ssd-ram-endurance,3475.html
thought I'd share it with you.. what do you think..
Did you find the 1tb-SSD? try newegg.

Hp Envy 15t-j000 Slow WiFi

I've had my Hp Envy 15t-j000 (Windows 8) for about a week and my only complaint is the WiFi is painfully slow. The speed which it takes to download large files or load web pages with lots of images is much slower than my 3 year old Acer laptop. I used the Network Speed app to test the speed of the connection and the download speed averages out at about .7 Mbps. The Wifi card is : Realtek RTL8188EE I have a TP-Link Wireless N Router and I've had no issues with previous computers or my Apple TV, which streams HD content with no problem. When I use the Netflix app on the Hp Envy, the 1080p content looks grainy because the WiFi connection isn't fast enough. This issue really is making me think about returning the computer. I've downloaded and installed the latest driver for the WiFi card from the HP site. I've also updated the firmware of my router, but still no change. I noticed this issue right after setting up my computer initially and downloading some large files from the Internet, so I don't believe it can be any type of software issue (basically I don't want to restore my machine as I have many files and programs already loaded). I've read in other forums that some people are experiencing the same issues. Is there any other solutions to fix this issue? Is anyone getting the expected WiFi speeds with this machine?

After more time, I retract my statement that ajusting power management and wireless options fixed the issue. I had less disconnects and more time before being disconnected but did not fix the issue. Since I purchased two exactly same laptops, I decided to make changes to only one until the problem was proven fixed. Contacted HP Support chat session and had me update windows and reset TCP/IP stack - did not fix the issue. I have Intel wireless and bluetooth card (Centrino wireless-n-2230), so I downloaded an apparent more recent driver for this card directly from Intel, which seemed to help but not fix the problem. I note this card is different from others without bluetooth reporting same issue on this thread. Just so happened that my wife called AT&T UVerse (my internet provider and wireless router hardware) about one of the tv boxes requiring reboot often. It was a wireless tv box and UVerse tech ended up changing lots of hardware and said there were several problems corrected. Since the UVerse tech changed wireless router I have not had the disconnect issue on either laptop. So the laptop that ony had a couple power management and wireless options changed has not had any disconnect or slow wireless problems since. And neither has the second identical one with more changes tried. So I conclude that the router hardware or setup doesn't like either this laptop or Windows 8 (other HP and other brand laptops running Windows 7 never had issues during entire time).

Disable touch pad HP ENVY 15t-j000

How to quickly disable touchpad on HP ENVY 15t-j000?
I just got one of the newest Haswell notebook. With older HP laptop touch pads there is a spot at the upper left corner to disable the touchpad. With the latest Synaptic touchpad on the new ENVY 15t there is no keyboard or touchpad button to disable the touchpad when you are using a mouse.
Please advice.
This question was solved.
View Solution.

Hi
The touchpads on some new notebooks do not have an on/off button go to control panel The touchpad itself does not have a dot or hardware switch toturn on/off. However, you can turn this function on and off from the control panel.
Let us know how it goes!
"I work for HP."
****Click the (purple thumbs up icon in the lower right corner of a post) to say thanks****
****Please mark Accept As Solution if it solves your problem****
Regards
Manjunath

New bios ruined my HP ENVY 15t-j000 Quad Edition CTO Notebook PC

i m using win 8.1 my laptop model is HP ENVY 15t-j000 Quad Edition CTO Notebook PC
core i7 16 gb ram
now the new bios version showing me F.64 Insyde
it was working fine & i just update the bios its restarts after completing bios update its get again restart
& now its not recognising hard disk any more
i tried with another hard disk but same
i have some precious data in chrom & firefox history
i checked its hard drive on another laptop & its working fine
& the error i m facing is
boot device not found
please install an operating system on your hard disk
hard disk (3F0)

This is NOT official HP Customer Support and I, as most other persons on this forum, do not work for HP. This is a peer-to-peer user supported forum for HP consumer class products. HP maintains no official presence on this forum and it is unlikely that HP will respond in an official capacity. Any reply from an HP employee represents their own opinion and not that of HP's.
There is nothing wrong with your computer. The flash to F.64 went fine, however the new BIOS can't locate the boot record on the hard drive. Please back-up the hard drive, including all your personal data using a Linux LiveCD and external hard drive, or connect the drive to another working computer.
Next, use the HP Recovery Media you created when you first setup the computer to return it to a factory like state. If you didn't create your HP Recovery Media when you first setup your computer, please contact official HP support in your region / country, via the HP Worldwide Support Portal, to see if HP Recovery Media is available for your computer.
If you have any further questions, please don't hesitate to ask.
Please click the White KUDOS "Thumbs Up" to show your appreciation
Frank
{------------ Please click the "White Kudos" Thumbs Up to say THANKS for helping.
Please click the "Accept As Solution" on my post, if my assistance has solved your issue. ------------V
This is a user supported forum. I am a volunteer and I don't work for HP.
HP 15t-j100 (on loan from HP)
HP 13 Split x2 (on loan from HP)
HP Slate8 Pro (on loan from HP)
HP a1632x - Windows 7, 4GB RAM, AMD Radeon HD 6450
HP p6130y - Windows 7, 8GB RAM, AMD Radeon HD 6450
HP p6320y - Windows 7, 8GB RAM, NVIDIA GT 240
HP p7-1026 - Windows 7, 6GB RAM, AMD Radeon HD 6450
HP p6787c - Windows 7, 8GB RAM, NVIDIA GT 240

A simple question about performance!

Hi! I have a simple question about performance. Suppouse that you have a servlet or a class with DB access, and you need to use a value several times in that page. What is best, to assign the value from say, a resultset or a request.getParameter() to a variable or to call the resultset or the request every time you need to retrieve that value? Which option uses less memory, which is faster, etc.?
Hoping the best fou u
Raul

If you need more values from a db, the best is to open some connections (connection pool) and use the for accessing the db.
To get the data only once, open the connection, get the data, store the data whereever you want: variable (class), hidden control (if you want to send from one page to another by request) and close the connection as quicky as possible.
The advantage of the first method is that the most time consuming activity (connections opening) is done only once.

Downgrade Envy 15t-j000 to windows 7, need help finding drivers

I installed windows 7 on my hp envy 15t-j000 and am having a hard time finding all the drivers. Here are some of the specs on mine, any help would be appreciated.
• 4th generation Intel(R) Core(TM) i7-4700MQ Processor
• NVIDIA GeForce GT 740M Graphics with 2048MB of dedicated video memory
• 15.6-inch diagonal Full HD BrightView LED-backlit Display
• 802.11b/g/n WLAN and Bluetooth(R)

Except for the USB controller, here are the rest of the drivers. Please try them and let me know. In the meantime, I will findout a way to share the USB drivers with you.
3D Video Controller
ftp://ftp.hp.com/pub/softpaq/sp61001-61500/sp61270.exe
Network Controller
ftp://ftp.hp.com/pub/softpaq/sp58501-59000/sp58641.exe
PCI Device
ftp://ftp.hp.com/pub/softpaq/sp61001-61500/sp61260.exe
SM Bus Controller
ftp://ftp.hp.com/pub/softpaq/sp61001-61500/sp61265.exe
Unknown Device
ftp://ftp.hp.com/pub/softpaq/sp61001-61500/sp61263.exe
Unknown Device
ftp://ftp.hp.com/pub/softpaq/sp62001-62500/sp62131.exe
I am an HP employee.
Regards,
Vidya
Make it easier for other people to find solutions, by marking my answer “Accept as Solution” if it solves your problem.
***Click on "Thumbs up" button to the bottom right side of my post to say thanks!***

Listen Up HP! I have some advice about the new ENVY 15t Touch!

Hello HP and everyone!
I'm interested in purchasing a brand new HP ENVY 15t Touch, and would have ordered a fully-optioned one today, except my purchase came to a screeching halt when I saw HP's options for "Processor and Graphics" offered for the laptop. I was slightly disappointed to find that HP now only offers the CPU and the graphics in a "bundle" as opposed to separate options, but I was astonished to see what the bundled options were!
See, the base processor and graphics are "4th generation Intel® Core™ i7-4710HQ Quad Core Processor + Intel® HD Graphics 4600," which is to be expected. I like the i7-4710HQ, but wanted more in terms of graphics, so I looked down the list and found the next option to be, at a $70 upcharge, "4th generation Intel® Core™ i7-4510U Dual Core Processor + 2GB NVIDIA GeForce 840M Graphics." I found the third option to be "4th generation Intel® Core™ i7-4510U Dual Core Processor + 4GB NVIDIA GeForce GTX 850M Graphics" for $140 over the base option.
I found these next two choices to be highly frustrating. I think it's absurd that HP insists I downgrade my CPU substantially just because I don't want the integrated graphics on their top-performing laptop, and then upcharges the CPU downgrade! Respectfully, I think that was a terrible move! Why HP can't offer both a quad core i7 and a stand alone video card? They did on their previous generation of the Envy 15 Touch, so I'm pretty sure it's not a power consumtpion issue.
So, HP, please offer your top-tier high-performance laptop with both a quad core i7 and at least an NVIDIA GeForce 840M. I think you will satisfy more of your high-performance customers, and lose less of them to your competitors. I would have loved to order one of these laptops today with both the i7-i7-4710HQ and the 4GB NVIDIA GeForce GTX 850M, but it seems that isn't going to happen right now. I will be looking elsewhere to buy a laptop unless this changes.

As far as payment goes, I agree with the at least 50% up front rule. As far as how much you charge, that will depend on how many days of production and post production are being planned. Also your skills should come into play. This is a completely different job than your typical work and requires a much different skill set.
If you really believe in the show AND the producers ability to sell it, you may want to offer a discount on production of the pilot for a signed contract guaranteeing you the production contract of the series once it has funding. If you don't believe in both the show and the future potential, charge them full rate card, as there won't be any future work coming from this show.
Another thing to factor in is your ability. Producing a pilot is a completely different animal than doing events and wedding. Can you pull it off, honestly? Can you bring the vision to full potential?
Finally I can't stress enough the producers ability to sell it. It's not easy to get a foot in the door at the networks. Most often they only work with companies they've worked with in the past. They come up with new ideas and match them up with a vendor they already work with.

Envy 15t J000 Quad edition CTO BBV error?

HI everyone! I just got a envy 15t, and decided that I'd rather replace the standard hard drive with a SSD. I created recovery media (wasted 2 disks that failed to complete), and was going through the process of booting the SSD from the recovery media when I got "restoration Incomplete". It got through copying information from the 6 disks fine, and was (I think) in the process of installing drivers and the like, when it stopped. It gave me 3 options; save log, details, and retry. retry does nothing, as I insert the disk as instructed, but they fail to be recognized as recovery media. I've installed everything twice, and it failed twice, and the diagnostics on the computer return PASSED when run on the SSD.
The following is what came off the details page, with removal of time code. Help??!! HP phone Reps have no clue as to whats going on.
ChkErrBB.CMD : Detect some error during PININST_BBV.
check C:\system.sav\logs\BurnBootWarn.log
or, check check C:\system.sav\logs\BurnBootMerge.log
Critical error condition was detected at BBV1...
Refer the following file if exists.
- c:\system.sav\logs\BurnBootWarn.log
- c:\system.sav\logs\BurnBoot.log
Switch to 2ndCap's WinPE and show [Recovery Manager]'s Incomplete dialog.
because RM's dialog can't appear on [Start] screen in Win 8 enviroment.
customer may not notice RM already shows error dialog.
There migt be unexpected reboot during BBV Clean or Last....
The process will cause CTO panic becuase the image might not be normal...

Hello, no I ended up just purchasing Windows 8 Pro and installing a fresh version on my HP Envy Touchsmart j053cl.
I installed a new SSD in the laptop and the recovery disks simply wouldn't get past the BBV error, even after I reset the default settings on the BIOS.
I spoke with HP support and they told me the recovery disks would not work with an SSD, which was really disappointing, as I've owned many HP laptops that have supported SSD easily. They also wouldn't send me a free new set of recovery disks because mine may have been broken.
I really love my Envy 15 and think HP should always keep the customer who wants to use SSD's in mind, as they are fairly common with users who own quad core Intel laptops. Thanks.

Envy 15t j000 no lights, no power

My envy 15t won't power up and shows no LED lights at power cord connection. I've tried the hard restart and still nothing. I tested the AC power adapter with a multimeter and it is working.

Hello @fisher329 ,
Welcome to the HP Forums!
I understand your ENVY 15t does not power up.
If you have confirmed the adapter is functional you have an internal power problem. This could be the internal power connector or the motherboard.
For this you will need to contact HP Phone Support for service options. You can contact HP Technical Support at 1-800-474-6836 in North America. For all other regions click here.
Thanks!
Please click the "Kudos, Thumbs Up" at the bottom of this post if you want to say "Thanks" for helping!
Please click "Accept as Solution" if you feel my post solved your issue, it will help others find the solution.
The Great Deku Tree
I work on behalf of HP.

A question about Performance Settings

         Dear all.
                       Hi all,I want add a performance poller about Environmental Temperature.
                        There is an error as shown in the figur:
                        The device is Nexus 7010. Is it support this poller ?
                          If support,how to setting ?
                         Thank you very much

Peanuts
Thank you for your time and help.
Dumb question Reflash the firm ware
Means Install the new firm ware list on this web site
my old is v3.0.02 build 003 june 4, 2009
The new one is v3.0.02 build 4 12/10/09
The MTU thing Ican figure out. click save OK. But what the heck is
Power cycle the router
Un-plug it ?
Sorry to a pain. Ready to throw this out the window. It works good/great then very poor or not at all. In wireless mode.
The other day on the lap top a friend was connected to a inter-active training video. for about 30 minutes, worked great.
Then today the Dell with windows 7 lost the wireless conection.
Thanks

A question about performance of envy 15t-j000

Similar Messages

Maybe you are looking for