A question about RMAN

This is on 10g.
We have database backups taken through traditional routes - i.e cold backup of Datafile,control files and redo log files to Tapes. This backup was taken without RMAN.
Can we restore this backup to a new database instance using RMAN?
So in essence, what I am asking is ; does RMAN allows restore from backups which are not taken using RMAN?
Thanks
R

User10212775,
If the short answer is no, then explain why you couldn't catalog the datafiles and a controlfile from the backup. If you can do that, and at the same time specify that the datafiles are level 0, why couldn't you restore the files to wherever? Only caveat is that the files need to be on disk to be cataloged.
Looked at another way, what if you are just starting to use RMAN? Your answer implies that any backup taken prior to starting the use of RMAN are near worthless. Why can't prior backups be added to a new catalog?

Similar Messages

Question about RMAN

Imagine the following scenario: In a Database A, an export (full mode) is made at 1:00 a.m and a full database backup (datafiles, archivelogs, controlfile and spfile included), made with RMAN, is made at 8:00 a.m. In case of total disaster, where all the datafiles of Database A were lost (let’s say that the hard disk crashes) and I would need to recreate the Database, would it be possible to create the Database (called now Database B) from the export and then apply all the changes that took place from 1:00 to 8:00 by using the RMAN backup?. If it is possible, how would I make it?
Thank you very much

What you need to do is have you database in archive log mode.
You can't use the export to appy changes(roll forward) database to prior disaster, because as far as Oracle is concerned this will be a NEW database.
If you run your database in archive log mode. Perform an RMAN backup A (cold or hot), perform RMAN backup B (cold or hot) then restore backup A, as long as you have the archive logs, you can roll the database forward to point of disister.
Paul.

About RMAN backup !!!!

Dear Friends,
Let my production server running starts from 1st June .
In 15 june , I take the First rman full (or level0) backup using the command :
RMAN> backup database plus archivelog;
In 20 June I take 2nd rman full backup using : RMAN> backup database plus archivelog;
Again in 30 June , I take the Third(3rd) rman full (or level 0) backup using the command :
RMAN> backup database plus archivelog;
And also my rman policy set as :
CONFIGURE RETENTION POLICY TO REDUNDANCY 1;
In the above scenario , I have the following questions :
1) When I take the Third(3rd) backup then is it the First RMAN backup goes to obsolete as per my rman policy ( RETENTION POLICY TO REDUNDANCY 1) ?
2) Is the above all RMAN backup make a link between them ?
3) If my first RMAN backup goes to obsolete and I have to delete the First RMAN backup , then which types of problem I face ? Can I go to previous state(suppose I need to back in 1st June) of my server if I delete First rman backup ?
4) when I take 3rd rman full backup , then is it all information from 1st january of the server are stored in the 3rd backup ? i.e., is the 3rd rman backup stores all the previous two rman backups information ?so that If I delete the previous two backup , then I get all information form 3rd rman backup .what is the actual scenario ......
plz help me to make clear concept about it .......
thx in advance .....

1) When I take the Third(3rd) backup then is it the First RMAN backup goes to obsolete as per my rman policy ( RETENTION POLICY TO REDUNDANCY 1) ?The REDUNDANCY parameter of the CONFIGURE RETENTION POLICY command specifies how many backups of each datafile and control file that RMAN should keep. In other words, if the number of backups for a specific datafile or control file exceeds the REDUNDANCY setting, then RMAN considers the extra backups as obsolete.So as in your case the redundancy is 1 so the 1st and 2nd backup are obsolete.
To check the obsolete backups run
rman> report obsolete;
To delete them
rman> delete obsolete;
Link:[http://download.oracle.com/docs/cd/B19306_01/backup.102/b14192/setup005.htm#BRBSC400]
Is the above all RMAN backup make a link between them ?I am not very much clear with the question.The RMAN information is stored in the controlfile.You can also create a new recovery catalog and register the target database. The RMAN repository records in the control file will be copied to the new recovery catalog.
when I take 3rd rman full backup , then is it all information from 1st january of the server are stored in the 3rd backup ? i.e., is the 3rd rman backup stores all the previous two rman backups information ?so that If I delete the previous two backup , then I get all information form 3rd rman backupThe 3rd RMAN backup will contain all the information of the DB from the very 1st day.You will get all the information in the 3rd rman backup as its a level 0 or what we say a FULL DATABASE BACKUP.If suppose the 3rd rman backup would have been a incremental backup, then you would have required a full backup, previous to the incremental one, so that after restoring the full backup, you restore the incremental to recover the DB completely.
Link:[http://download.oracle.com/docs/cd/B19306_01/backup.102/b14191/part1.htm#i996723]
[http://download.oracle.com/docs/cd/B19306_01/backup.102/b14192/bkup004.htm#BRBSC133]
Forgot to answer the 3rd question
3) If my first RMAN backup goes to obsolete and I have to delete the First RMAN backup , then which types of problem I face ? Can I go to previous state(suppose I need to back in 1st June) of my server if I delete First rman backup ?well, i am not very much sure , but i think is , if you have the 1st rman backup pieces physically present on the disk, you can catalog it and then use the rman command to restore the data from it of till 1st june.
To catalog the backup pieces use
rman> catalog backuppiece 'filename';
Link: [http://download.oracle.com/docs/cd/B19306_01/backup.102/b14192/maint007.htm]
HTH
Anand
Edited by: Anand... on Oct 15, 2008 10:51 AM

Question about RAC and ASM

Hi,
We are thinking about build RAC using ASM for OEM database. It'll have two nodes, oracle 10g and Hitachi san with solaris ( or linux ). I've few questions about RAC and ASM.
1) Do I need to have ASM instance running on each node ? ( most likely yes... but want to make sure )
2) can I share oracle_home between ASM instance and database instance ? what is the best choice ?
3) I'm planning to use shared disks for all files, all databases.... what are the pros/cons ?
4) what should be the installation procedure ? Meaning, first create ASM instance on each node, then install cluster software, build RAC databases...... can someone explain..
5) I believe RMAN is the only option for backup since I'm using ASM, correct ?
I'm a newbie to RAC and ASM..
Thanks,

user4866039 wrote:
1) Do I need to have ASM instance running on each node ? ( most likely yes... but want to make sure )yes.
2) can I share oracle_home between ASM instance and database instance ? what is the best choice ?in 10g you can, in 11gr2 you cannot. and it might be better to seperate them because it will give you more flexibility with patching.
3) I'm planning to use shared disks for all files, all databases.... what are the pros/cons ?if you share your oracle_home you won't be able to do rolling updates. so i recommend to keep oracle_homes local.
4) what should be the installation procedure ? Meaning, first create ASM instance on each node, then install cluster software, build RAC databases...... can someone explain..follow the install guide for your respective version. for 10g you'd install clusterware first, then asm and database is last.
5) I believe RMAN is the only option for backup since I'm using ASM, correct ?pretty much. you could stop your database and dump the raw devices or use asmcmd/asmftp but rman is definitely the best choice
Bjoern

Questions about your new HP Products? HP Expert Day: January 14th, 2015

Thank you for coming to Expert Day! The event has now concluded.
To find out about future events, please visit this page.
On behalf of the Experts, I would like to thank you for coming to the Forum to connect with us. We hope you will return to the boards to share your experiences, both good and bad.
We will be holding more of these Expert Days on different topics in the months to come. We hope to see you then!
If you still have questions to ask, feel free to post them on the Forum – we always have experts online to help you out.
So, what is HP Expert Day?
Expert Day is an online event when HP employees join our Support Forums to answer questions about your HP products. And it’s FREE.
Ok, how do I get started?
It’s easy. Come out to the HP Support Forums, post your question, and wait for a response! We’ll have experts online covering our Notebook boards, Desktop boards, Tablet boards, and Printer and all-in-one boards.
We’ll also be covering the commercial products on the HP Enterprise Business Community. We’ll have experts online covering select boards on the Printing and Digital Imaging and Desktops and Workstations categories.
What if I need more information?
For more information and a complete schedule of previous events, check out this post on the forums.
Is Expert Day an English-only event?
No. This time we’ll have experts and volunteers online across the globe, answering questions on the English, Simplified Chinese, and Korean forums. Here’s the information:
Enterprise Business Forum: January 14th 7:00am to 12:00pm and 6:00pm to 11:00pm Pacific Time
Korean Forum: January 15th 10am to 6pm Korea Time
Simplified Chinese Forum: January 15th 10am to 6pm China Time
Looking forward to seeing you on January 14th!
I am an HP employee.

My HP, purchased in June 2012, died on Saturday. I was working in recently installed Photoshop, walked away from my computer to answer the phone and when I came back the screen was blank. When I turned it on, I got a Windows Error Recovery message. The computer was locked and wouldn't let me move the arrow keys up or down and hitting f8 didn't do anything.
I'm not happy with HP. Any suggestions?

Have questions about your Creative Cloud or Subscription Membership?

You can find answers to several questions regarding membership to our subscription services. Please see Membership troubleshooting | Creative Cloud - http://helpx.adobe.com/x-productkb/policy-pricing/membership-subscription-troubleshooting- creative-cloud.html for additional information. You can find information on such topics as:
I need help completeing my new purchase or upgrade.
I want to change the credit card on my account.
I have a question about my membership price or statement charges.
I want to change my membership: upgrade, renew, or restart.
I want to cancel my membership.
How do I access my account information or change update notifications?

Branching to new discussion.
Christym16625842 you are welcome to utilize the process listed in Creative Cloud Help | Install, update, or uninstall apps to install and evaluate the applications included with a Creative Cloud Membership. The software is fully supported on recent Mac computers. You can find the system requirements for the Creative Cloud at System requirements | Creative Cloud.

Questions about using the Voice Memos app

I'm currently an Android user, but will be getting an iPhone 6 soon. My most used app is the voice memos app on my Android phone. I have a couple questions about the iPhone's built-in voice memos app.
-Am I able to transfer my voice memos from my Android phone to my iPhone, so my recordings from my Android app will show up in the iPhone's voice memos app?
-When exporting voice memos from the iPhone to computer, are recordings in MP3 format? If not, what format are they in?
-In your opinion, how is the recording quality of the voice memos app?

You cannot import your Android voice memos to your iPhone's voice memo app. You might be able to play the Android memos and have the iPhone pick up the audio and record it.
Here is the writeup about sending voice memos from the iPhone to your computer (from the iPhone User Guide):
App quality is excellent.

Re: Question about the Satellite P300-18Z

Hello everyone,
I have a couple of questions about the Satellite P300-18Z.
What "video out" does this laptop have? (DVI, s-video or d-sub)
Can I link the laptop up to a LCD-TV and watch movies on a resolution of 1080p? (full-HD)
What is the warranty on this laptop?

Hello
According the notebook specification Satellite P300-18Z has follow interfaces:
DVI - No DVI port available
HDMI - HDMI-out (HDMI out port available)
Headphone Jack - External Headphone Jack (Stereo) available
.link - iLink (Firewire) port available
Line in Jack - No Line in Jack port available
Line out Jack - No Line Out Jack available
Microphone Jack - External Micrphone Jack
TV-out - port available (S-Video port)
VGA - VGA (External monitor port RGB port)
Also you can connect it to your LCD TV using HDMI cable.
Warranty is country specific and clarifies this with your local dealer but I know that all Toshiba products have 1 year standard warranty and also 1 year international warranty. you can of course expand it.

Some questions about Muse

First of all, I would like to say that I am very impressed with how well Muse works and how easy it was to create a website that satisfies me. Before I started a daily updated website I thought I would encounter many problems I will not be able to solve. I have only had a few minor issues which I would like to share with you.
The most problems I have with a horizontal layouts (http://www.leftlane.pl/sty14/dig-t-r-3-cylindrowy-silnik-nissana-o-wadze-40-kg-i-mocy-400- km.html). Marking and copying of a text is possible only on the last (top) layer of a document. The same situation is with widgets or anything connected with rollover state - it does not work. In the above example it would be perfect to use a composition/tooltip widget on the first page. Unfortunately, you cannot even move the cursor into it.
It would be helpful to have an option of rolling a mouse to an anchor (like in here http://www.play.pl/super-smartfony/lg-nexus-5.html and here http://www.thepetedesign.com/demos/onepage_scroll_demo.html). I mean any action of a mouse wheel would make a move to another anchor/screen. It would make navigation of my site very easy.
Is it possible to create a widget with a function next anchor/previous anchor? Currently, in the menu every button must be connected to a different anchor for the menu to be functional.
A question about Adobe Muse. Is it possible to create panels in different columns? It would make it easier to go through all the sophisticated program functions.
The hits from Facebook have sometimes very long links, eg.
(http://www.leftlane.pl/sty14/mclaren-p1-nowy-krol-nurburgring.html?fb_action_ids=143235557 3667782&fb_action_types=og.likes&fb_source=aggregation&fb_aggregation_id=288381481237582). If such a link is activated, the anchors in the menu do not work on any page. I mean the backlight of an active state, which helps the user to find out where on page they currently are. The problem also occurs when in the name of a html file polish fonts exist. And sometimes the dots does not work without any reason, mostly in the main page, sometimes in the cooperation page either (http://www.leftlane.pl/wspolpraca/). In the first case (on main page), I do not know why. I have checked if they did not drop into a state button by accident, moved them among the layers, numbered them from scratch and it did not help. In the cooperation page, the first anchor does not work if it is in Y axle set at 0. If I move it right direction- everything is ok.
The text frame with background fill does not change text color in overlay state (http://www.leftlane.pl/sty14/nowe-mini-krolestwo-silnikow-3-cylindrowych.html). I mean a source button at the beginning of every text. I would like a dark text and a light layer in a rollover, but the text after export and moving cursor into it does not change color for some reason.
I was not sure whether to keep everything (whole website) in one Muse file (but I may be mistaken?). I have decided to divide it into months. Everyone is in a different Muse file. If something goes wrong, I will not have any trouble with an upload of a whole site, which is going to get bigger and bigger.
The problem is that every file has two master pages. Everything works well up to the moment when I realize how many times I have to make changes in upper menu when I need to add something there. I have already 5 files, every with 2 masters. Is there any way to solve this problem? Maybe something to do with Business Catalyst, where I could connect a menu to every subpage independently, deleting it from Muse file? Doing so I would be able to edit it everywhere from one place. It would make my work much easier, but I have no idea jendak how to do it.
The comments Disqus do not load, especially at horizontal layouts (http://www.leftlane.pl/sty14/2014-infiniti-q50-eau-rouge-concept.html). I have exchanged some mails and screenshots with Disqus help. I have sent them a screenshot where the comments are not loaded, because they almost never load. They have replied that it works at their place even with attached screenshot. I have a hard time to discuss it, because it does not work with me and with my friends either. Maybe you could fix it? I would not like to end up with awful facebook comments ;). The problem is with Firefox on PC and Mac. Chrome, Safari and Opera work ok.
YouTube movie level layouts do not work well with IE11 and Safari 7 (http://www.leftlane.pl/sty14/wypadki-drogowe--004.html). The background should roll left, but in the above mentioned browsers it jumps up. Moreover the scrolling with menu dots is not fluent on Firefox, but I guess it is due to Firefox issues? The same layout but in vertical version rolls fluently in Firefox (http://www.leftlane.pl/sty14/polskie-wypadki--005.html).
Now, viewing the website on new smartphones and tablets. I know it is not a mobile/tablet layout, but I tried to make it possible to be used on mobile hardware with HD (1280) display. I mean most of all horizontal layouts (http://www.leftlane.pl/sty14/2015-hyundai-genesis.html), where If we want to roll left, we need to roll down. Is there a way to make it possible to move the finger the direction in which the layout goes?
On Android phones (Nexus 4, Android 4.4.2, Chrome 32) the fade away background effect does not work, although I have spent a lot of time over it (http://www.leftlane.pl/lut14/koniec-produkcji-elektrycznego-renault-fluence-ze!.html). It is ok on PC, but on the phone it does not look good. A whole picture moves from a lower layer instead of an edge which spoils everything.
This layout does not look good on Android (http://www.leftlane.pl/sty14/nowe-mini-krolestwo-silnikow-3-cylindrowych.html#a07). The background does not fill the whole width of a page. There are also problems with a photo gallery, where full screen pictures should fill more of a screen.
Is it possible to make an option of scroll effects/motions for a fullscreen slideshow widget thumbnails (http://www.leftlane.pl/sty14/2014-chevrolet-ss%2c-rodzinny-sedan-z-415-konnym-v8.html#a06)? It would help me with designing layouts. Currently, it can go from a bottom of a page at x1 speed or emerge (like in this layout) by changing opacity. Something more will be needed, I suppose.
Sometimes the pictures from gallery (http://www.leftlane.pl/sty14/2014-chevrolet-ss%2c-rodzinny-sedan-z-415-konnym-v8.html#a06 download very slowly. The website is hosted at Business Catalyst. I cannot state when exactly it happens, most of the time it works ok.
I really like layouts like this (http://www.leftlane.pl/sty14/2014-chevrolet-ss%2c-rodzinny-sedan-z-415-konnym-v8.html#a03). On the top is a description and a main text, and the picture is a filled object with a hold set at the bottom edge. That is why there is a nice effect of a filling a whole screen- nevertheless the resolution that is set. It works perfect on PC, but on Android the picture goes beyond the screen. You can do something about it?
In horizontal layouts (http://www.leftlane.pl/sty14/dig-t-r-3-cylindrowy-silnik-nissana-o-wadze-40-kg-i-mocy-400- km.html) holding of a filling object does not work. Everything is always held to upper edge of a screen regardless the settings. Possibility of holding the picture to the bottom edge or center would make my work much easier.
According to UE regulations we have to inform about the cookies. I do not know how to do it in Muse. I mean, when the message shows up one time and is accepted, there would be no need to show it again and again during another visit on the website. Is there any way to do it? Is there any widget for it maybe?
The YouTube widget sometimes changes size just like that. It is so when the miniature of the movie does not load, and the widget is set to stroke (in our case 4 pixels, rounded to 1 pixel). As I remember ( in case of a load error) it extends for 8 pixels wide.
Last but not least - we use the cheapest hosting plan in Business Catalyst. The monthly bandwidth is enough, although we have a lot of pictures and we worried about it at first. Yet we are running out of the disk storage very quickly. We have used more than a half of a 1 GB after a month. We do not want to change BC for a different one, because we like the way it is connected with Muse. But we do not want to buy the most expensive package - but only this one has more disk space. We do not need any other of these functions and it would devastate our budget. Do we have any other option?
I’m using Adobe Muse 7.2 on OS X 10.9.1.
and I'm sending Muse file to <[email protected]>

Unfortunatley, there is no way to get a code view in Muse. I know quite a few people requested it in the previous forum, but not really sure where that ended up. Also, you may not want to bring the html into DW unless you only have 1 or 2 small changes 2 make. Two reasons. First, it isnt backwards compatible, so if you are planning on updating that site in Muse, you will need to make those changes in DW everytime you update. Second, by all accounts the HTML that Muse puts out is not pretty or easy to work with. Unlike you, I am code averse, but there was a lenghty discussion on the previous forum on this topic. I know they were striving to make it better with every release, just not sure where it is at this point.
Dont think I am reading that second question right, but there was a ton of info on that old site. You may want to take a look there, people posted a ton of great unique solutions, so it worth a look.
Here is the link to the old forums- http://support.muse.adobe.com/muse

HT201303 hi just got my new apple ipod touch i need to update my security information other wise it wont let me download apps it says to enter three questions about myself and i get to the third question and it wont let me enter the third question

hi just got my new apple ipod touch and to download apps it wants to add questions about myself for more sercurity information. i get up to question 3 and it wont let me select a question but it will let me write an answer so i just pressed done and then it says i cant carry on because ive mised out information when it wont let me do a question!

Welcome to the Apple community.
You might try to see if you can change your security questions. Start here, change your country if necessary and go to manage your account > Password and Security.
I'm able to do this, others say they need to input answers to their current security questions in order to make changes, I'm inclined to think its worth a try, you don't have anything to lose.
If that doesn't help you might try contacting Apple through Express Lane (select your country, navigate to iCloud help and enter the serial number of one of your devices)

Just installed iOS6, questions about "iMessage" and other things...

I've been a satisfied iOS4 user since I bought my iPhone4, but I was forced to install iOS6 tonight in order to download a "free" app. I found a few new icons on the screen along with about 200 percent more "Settings" I'd like to ask some questions about. I'm sure a few of these could be answered by doing a frantic and thorough search through weeks of posts but I'm a little short on time right now.
First, what exactly is iMessage? Looking at the page for it, I can't see any difference between it and regular text messages. The info page says its to avoid charges, but between my data plan and not being charged for text I don't see where theres any other benefit. The one person I text with the most recently asked me why I had not installed iMessage yet, and didn't have an answer when I asked him why I should. I guess he just wanted to see text replies in blue instead of green.
In a related bit, flipping through Settings>Messages>Send & Receive I find a "2 addresses" section, with my phone number in there as well as my email under "You can be reached by iMessage at:" and "Start new conversations from:". What good does it do iMessages to have my email address? Does the Mail app handle text as well as email addresses? That seems to be the only explanation, and also very odd to think I'd be trying to text through my Mail app.
Second, looking through the Settings>Mail I see now that I have an icloud email address as well as the mac.com address I've been desperately hanging on to for the past 10 years, and the me.com address they've been trying to force me into since those came out. (I was happy to see I could delete the me.com address from the phone. I wish I could delete it from the universe.)
I wasn't even aware there was a such thing as icloud.com addresses. When did this happen? What is it used for?
Third, under that icloud Setting I see a long list of apps with buttons labeled "Off" under it. What are those for? Under the Mac.com settings I see switches for "Mail" and "Notes", with Mail on and Notes off. The Notes app (which I haven't used since my old iPhone 3) still opens, regardless of this setting.
Fourth, I now have an item called "Facetime" under my Settings. It is off, but underneath it says "Your phone number and/or email address will be shared with people you call". I understand caller ID normally sends caller number info to the receiver, but why would someone need my email address if I call them?
Fifth, I now have a "Music" setting, at the bottom of which I see a "Home Sharing" item, which when clicked brings up my AppleID and asks me if I want to Sign Out or Cancel. What is Home Sharing? Its also at the bottom of the "Video" settings.
Sixth, now I have Twitter and Facebook settings? For what? I don't have accounts with either of those companies. So why have settings, especially since it asks me to create accounts and download apps for those companies right in the Settings?
Seventh, there is a camera icon on the unlock screen. Touching it causes the screen to bounce up about a quarter inch, almost but not quite revealing something behind it. I should probably just quit asking about this stuff already, but I'll take the bait - what is this now?
Finally, what is the Notification Center used for?
If I got a text under iOS4, it would put an alert on the Unlock screen. Scrolling through this huge list of things under the Notification settings I'm really blown away by all the apps set up to yell at me. I can see having an alert for a text message but Game Center? What the heck is that, and why is it set up to hit me with a "Badge App Icon" (whatever that is) when I get alerts from "Everyone". Similarly, the phone is set to alert me to something called a "Photostream Alert"? What is this? Why is there a Phone section for the Notification Center? So they can put a Notice on my screen to tell me the phone is ringing? Holy cow! The phone is set to send me alerts from the "Weather Widget". So if I miss the fact its raining there will be a message on my screen to let me know? Whats next - a buzzer to tell me I'm listening to music?
There's a lot more, like what would I need Passbook for when I have the actual movie tickets, gate boarding passes, coupons, etc in my hands, but we'll leave that for another time. Many thanks to all who can offer some answers to my questions above.

Hey Taantumus!
Here is an article that will provide some guidance on this question:
Apple ID: Changing your password
http://support.apple.com/kb/ht5624
The next time you use an Apple feature or service that uses Apple ID, you'll be asked to sign in with your new Apple ID password.
Thanks for coming to the Apple Support Communities!
Regards,
Braden

Questions about using Bitlocker without TPM

We currently use Bitlocker to encrypt our Windows 7 computers with TPM. Now we are looking at encrypting some Windows 7 computers without a TPM. I see how to change the group policy setting to allow Bitlocker without a TPM. I have looked at a lot of other
threads and I have a few questions about how the Bitlocker without TPM works.
1) I see a USB drive containing a key is required for Bitlocker configurations without a TPM, say the end user loses this USB drive, what are the recovery options for their computer?
This article seems to indicate that without the USB drive connected, you are unable to even access recovery options http://blogs.technet.com/b/hugofe/archive/2010/10/29/bitlocker-without-tpm.aspx
We have recovery backed up to AD when Bitlocker is enabled, but how could we do this recovery on a computer on computer where it's USB is lost? Would we have to remove the HD itself and attach it to another computer to access?
2) After enabling Bitlocker on a computer without a TPM and using the USB Drive for the key, is there a way to also add a PIN or password protection at bootup?

Hi,
Sorry for my dilatory reply,
Configuring a startup key is another method to enable a higher level of security with the TPM. The startup key is a key stored on a USB flash drive, and the USB flash drive must be inserted every time the computer starts. The startup key is used to provide
another factor of authentication in conjunction with TPM authentication. To use a USB flash drive as a startup key, the USB flash drive must be formatted by using the NTFS, FAT, or FAT32 file system.
You must have a startup key to use BitLocker on a non-TPM computer.
From: http://technet.microsoft.com/de-de/library/ee449438(v=ws.10).aspx#BKMK_Key
For more Q&A about BitLocker, you can refer to the link above.
hope this is helpful.
Roger Lu
TechNet Community Support

Questions about Rooting...

Hi everyone, I’ve some questions about rooting my Xperia Arc S. Hopefully I’ll get helpful answers from you.
If I root my phone, shall I get regular software official updates from Sony?
Currently Sony is rolling out the ICS update. After rooting the phone am I able to upgrade my phone to ICS?
While rooting the phone if any damage is done, can that be recoverable by installing a fresh OS or something?
Does the rooting process delete all the existing contacts, messages, apps etc?
Finally can anyone please provide a full proof guide/tutorial for rooting the Xperia Arc S?
Thanks in advance.
Solved!
Go to Solution.

Do you have an app named Super USer ?
Were you on 4.0.4 and then rooted your mobile using this method ?
If yes then your mobile is not rooted for sure
See how to root 4.0.4 here
Discussion guidelines.
Message me or any other moderator to seek help regarding moderation.

A lot of questions about my MacBook Air

I am really new to re-using Apple computers.The last time I used an Apple computer was back in 1987 when the school and my family had Apple IIGS computers. I have been using PC's which reqiure Microsoft. I a lot of have questions (10 questions) about my MacBook Air and I hope you good people can and will help me.
Product: MacBook Air
Operating System: Mac OS X Version 10.7.4
1) I Downloaded MacKeeper because I was fooled. I had a bad feeling just before I Downloaded it and I should have listened to my heart. However, I didn't buy it or fully Install it. It was like a test run and then they wanted me to pay almost $100 for it. Thankfully, I didn't because I read it is Malware. I spoke with an Apple Tech at Apple Care and he helped me get rid of it (or so we think). I don't see it anymore on my computer. I read it can slow down your computer. How can you tell if it's really off of the computer?
2) When I open "Finder" and I see that there are people Sharing my computer with me. I went into AirDrop and it reads, "Other people can see your Mac as (my name) MacBook Air when their computer is nearby." I bought a HotSpot and while it's turned on and I selected it as my WI-FI connection I thought it would get rid of these people, protect what I type, me, my items, computer, etc. But it didn't.
I didn't know that I have to buy a exteral CD and/or DVD Player in order to connect to the brand new Modem and Router in one by NetGear. I am so used to PCs and the CD/DVD Players being built inside.
The people at Apple Store told me that there is an internal modem inside, but I don't know how to find it and what to do then. Should I use a Firewall?, An AntiVirus, AntiMalware, AntiSpyware, etc. Apple Care tech told me I don't need to get an AntiVirus.
3) Is there a new kind of Wireless Modem and Router that doesn't require a CD-ROM?
4) When I travel or fly and I am not close to home I was told by Best Buy and Sprint that I had to buy a mobile HotSpot to use the computer (WI-FI) safely. As I typed, I have one. But it's pretty expensive and only gives me 1 hour and 15 minutes per day to Stream. What can I do to use this computer safely Online when I am out of range from a Modem and Router? What do people do when they travel on airplanes?
5) This compter won't let me use "Raid." I think you have to have a newer version. I hard about Raid on the radio from Leo (can't recall his last name) who's a Tech expert.
6) Should I buy a ZipDrive? Apple Store Tech told me that I didn't need a ZipDrive. I just remember the episode of HBO's "Sex and The City" when Carrie looses everything because her copy crashed. Now, of course, I know that's a fictional show, but with PC's and Microsoft I have lost everything when it crashed, frooze up, etc. I know there's iClouds. I heard about Carbonite, but I have read the Pros and Cons about it. Mostly they are Cons about it. I just don't want to do anything wrong and mess up this computer.
7) Should I buy a new Printer/Copier/Scanner because mine is an HP. It's not new, but it works. I even have a CD-ROM for Macs. What about the new product called, "Neat"?
8) Is there a special product that I should buy to do Online Banking and/or other important stuff?
9) I saw and read about iWork in the Apps Store and it sounds cool. I still have alot of friends and colleagues who still use Microsoft. Is iWork good to use? Should I Download it from the Apple Apps Store or can a buy it at Apple? Is there another Word Processing Program that is great and user friendly and will work with Macs and PCs?
10) Should I Update the OS with OS X Mountian Lion Pro from the Apple Apps Store or buy it at Apple Store?
In advance, I wish to thank you in this Apple Support Communites for your help. Have a safe and happy holiday weekend!

1) Here are instructions for removing MacKeeper. Since it mostly consists of manually looking for folders and specific files, if you follow the instructions you either fail to find what you are told to find (because your AppleCare guide gave you complete instructions which you followed) or you'll find some additional files that need to be replaced.
2 & 3) I assume you are looking at the sidebar of a Finder window and seeing Shared and computers under it. Those are computers that you can potentionally share. To do so you'd need an account on their computer and a password. They are not sharing your computer.
AirDrop allows you to create an adhoc network for filesharing and it only functions when you have selected the AirDop item in the SideBar. Actually doing that merely announces to computers in the same network node that your computer is available for a file to be sent to. Even then you have to explicitly allow the file to be downloaded to your computer. Similarly you'd be able to see other computers with AirDrop selected and be able to send them a file - which they'd have to accept.
The only reason your NetGear Router comes with a CD is to install and run their 'easy' step by step configuration program. It can also be done manually with a browser. Read the manual to find the IP address you must enter to access the router's configuration menu. Apple's WiFi routers don't require a CD to install the software because the configuration software is already on your computer.
I do have my firewall turned on. AntiVirus software isn't a bad idea - I use Sophos having tested it for a review for our local User Group and I found I liked it better than ClamAVx which is what I'd been using before. Both are free.
4) I think you were scammed by Sprint and BestBuy. I use hotel, coffee shop, and restaurant WiFi spots and have for years. However, because they can be unsecured, I do not shop online or bank when I'm using them. I also use 1Password and don't reuse passwords so even if a sniffer should grab an account and password that's all it would get - one account.
5) Raid doesn't really make sense with a MacBook Air - a RAID involves 2 or more disks being used as if they were one.
6) Zip drive? No. External hard drive - yes. It isn't a question of if a computer's hard drive will malfunction, it is when. OWC has a nice selection of external drives and the Mac has a built in backup system called TimeMachine. Due to the way TimeMachine works, I've found that your TimeMachine drive should be at least twice as large - and preferably 3-4 times as large as the data you are backing up.
7) if your printer works and it has Mountain Lion drivers, why replace it?
8) Online banking is done with a browser - Use Safari or FireFox
9) If trading files with Windows users is important Mac: Office is your best bet. If not, iWork, Mac:Office, or LibreOffice are all good possibilities.
10) you can only buy Mt Lion via the App Store.

Some questions about configuration in MAX.

Hello,everyone!
I have some questions about configuration in MAX(I am a jackaroo for motion control development),I hope I can get your help.
I use PCI-7344+UMI-7764+Servo amplifier+Servo motor,my MAX version is 4.2 and I use NI-Motion7.5
My question as following:
1,In Axis Configuration,for motor type,why I must select stepper but not servo?my motor is servo motor!If I select Servo,my motor can't run,I don't know why.
If I select stepper,though motor can work but I can't test encoder in MAX.
2,In Stepper settings,for stepper loop mode,why I must select open-loop but not close-loop?If I select close-loop,the servo motor doesn't work too.
3,If I want my two servo motors run at different velocity,How shoud I do?It seems I just can set the same velocity in MAX for my two servo motors.
My English is poor,Pls pardon me!I come from China.
Thank you for your help!
EnquanLi
Striving is without limit!

Hi,Jochen,
Thank you for your kindly help!
The manufacturer of the drive and motor that I am using now is Japan SANYO DENKI,drive type is RS1A01AA,motor type is R2AA06020FXP00.
And I use position control mode,thehe encoder's counts per revolution is 131072.I set the electronic gear ratio to 1:1 for drive.
Now,I can use Close-Loop to control the motor but still has some problems.When I configure it to run in closed loop mode, the motors behave strangely and never move to the target position.When I configure it to run in closed loop mode, the motors behave strangely and never move to the target position.The detail situation is as following
1,Motor can't run.
2, Or motor moves to a position, then moves in the same direction agian and eventually stops.
Except for the two points mentioned above,"Following Error" is occured frequently,I don't know why.
I am still not clear why I must set the motor type be stepper in MAX .
And I have another question:what the relationship between the steps and the counts?They have the proportion relations?I notice that there are a section said like this in help document: For proper closed-loop and p-command operation, steps per revolution/counts per revolution must be in the range of 1/32,767 < steps/counts < 32,767. An incorrect counts to steps ratio can result in failure to reach the target position and erroneous closed-loop stepper operation.
I am verry sorry I have too many questions!
I am very appreciate for your kingly help!Thanks again!
EnquanLi
China
Striving is without limit!

A question about RMAN

Similar Messages

Maybe you are looking for