A single red line on screen

I started up my Macbook today and a single red line appeared on my screen.  I tried resetting the LCD (Control, Shift, Eject), but that did nothing.  The Macbook was purchased in 2008, so I am out of my extended warranty.
What do I do?  Please advise kindly.

this can be caused by:
bad bios (even though they never mentioned it was a dell)
monitor going bad
graphics card chip is going bad
connection between the monitor and your motherboard is bad (bad cable, lose cable) 
your eyes going bad (haha jk jk)
u can play around with the setting and end up frustration, or you can bring it in to geek squad and have them take a look at it.
if you bought the computer from best buy and bought the protection service plan/geek squad black tie protection plan, they will be able to take a look at it and hopefully it will be covered (depends on what's causing it)
if you bought the computer from best buy and did not buy the protection plan, or u didn't buy the computer from best buy at all, they will charge you $69 for a diagnostic fee, and they will tell you an estimate on how much it will cost for you to fix.

Similar Messages

  • SP6000: Red line on screen

    Hi, one of my SP6000's has a thin vertical red line about a single pixel wide going from top to bottom in the centre, other wise the screen is perfectly ok. The machine works perfectly in all aspects apart this red line.
    Anybody had a similar fault and if so, what was the cause of this?

    Hi Graham
    the answer is quite simple: your TFT is defective. Some of the curcuits driving the panel is defective. To get it to work properly you need to replace the screen.
    The cause for electrical components to fail is really hard to say - most of the times it just happens for no visible reason at all. Sometimes it comes from static, dust, shortcircuits.... a lot of different reasons.
    BR
    Tom

  • Ibook g3 12in Red line in screen

    Today My ibook g3 poped up with a red line to the right of the screen and want go away what could be doing this?

    A Google search finds this:
    http://askville.amazon.com/Ibook-g3-800-mhz-red-vertical-line-fix/AnswerViewer.d o?requestId=14733453
    Answer from JohnWasser
    Possibly a bad connection at the LCD.
    It sounds to me like the electrical connection feeding one column of the LCD has broken. Put a Post-it note on the screen with the sticky edge right along the red line. If the line doesn't move when you change screen resolutions then it's even more likely to be a column drive wire. If you connect an external display and you still see the problem then it's NOT the connections in the LCD. It may be possible, but fairly tricky, to re-solder the physical connection. You'd have to disassemble the screen quite a bit to get access to the connections. The wires are also very close together so it will be hard to re-heat one without accidentally connecting to the next. The safest solution is to live with the problem. 

  • Sony 46" LCD Vert. Red Line on screen

    I have a Sony 46" HDTV and have a Verticle Red Line from the top
    of the screen to the Bottom..  Can this be fixed with an adjustment.
    Can it be repaired. TV is 2 1/2 years old. Out of warranty.
    Great Picture except for this problem. Thanks
    Solved!
    Go to Solution.

    If it happens on all content and all sources (sat/cable/blu-ray/game/dvd/etc) it is likely a damaged transistor not allowing the red to shut off. Yes its repairable but at what cost I don't know you would have to get a estimate for that. Although I should add no matter what the actual cause is if its there all the time it will need to be serviced by a authorized repair technician.

  • Red line on screen

    How can I fix my ipod touch 4g if there is a red line in the middle of my screen and occasionally it flickers to a white line across the entire screen and makes my screen blink? It goes away sometimes if I leave my ipod alone for a while but then it comes back quickly.

    Try:
    - Reset the iOS device. Nothing will be lost
    Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Reset all settings
    Go to Settings > General > Reset and tap Reset All Settings.
    All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
    - Restore from backup. See:                                 
    iOS: How to back up           
    - Restore to factory settings/new iOS device.
    If still problem, make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
    Apple Retail Store - Genius Bar          

  • Red line down screen

    My monitor has a red line down the middle of the screen.   Does anyone know why this is happening?  Sometimes, depending on the background color, the line is green (on lighter backgrounds), otherwise it is red. 

    I have the EXACT same problem and also bought my iMac in Dec 2011. Thankfully I have AppleCare. I called support; had to back up the machine and take it in to an Apple Store for a new monitor and a new video card. They didn't seem to be all THAT horrified at the problem so perhaps it was a bad batch of monitors in that run of manufacturing.
    Anyway, I'm using my MacBook for now and they expect the iMac to be fixed ready in 3-5 days.

  • Powerbook G4 OSX 10.2 red line through screen

    Does anyone know what or why I would have a vertical thin red line through the screen..top to bottom; and is it serious? can it be fixed? What does it mean...
    soni

    Soni:
    It is helpful when we know which PB G4 you have. However, your thin vertical red line may be failing backlight lamp. If that is the case you don't need to worry about it, unless you want it gone. If it is convenient make an appointment at the Genius Bar and have them take a look at no cost to you.
    cornelius

  • Red line across screen imac

    i just bought a iMac 21,5" (2012) for 7 days.
    and i found a red line across the iMac screen sometimes.
    no problem found from the diagnostic mode.
    any other method for me to check the problem?
    or can i have a product return or refund, but not repair for this case?
    i will be very disappointed, if there is any QC issue for apple product.

    You can return a new Mac within 14 days of purchase.
    Return it and get another one.
    A new Mac comes with 90 days of free tech support from AppleCare.
    AppleCare: 1-800-275-2273

  • IPad red line across screen

    I was just using my iPad normally when all of a sudden, a red line appeared across the screen one pixel wide. I tried to restart and reset. Is there some other solution?

    If resetting didn't fix it, it appears you have a bad screen. You'll have to contact Apple by phone or at the Genius bar at an Apple store.
    They may replace your iPad, even if it is out of warranty, though I strongly doubt that. Otherwise, you can purchase a refurbished one on exchange as long as there is no water damage:
    If you own an iPad that is ineligible for warranty service but is eligible for Out-of-Warranty (OOW) Service, Apple will replace your iPad with an iPad that is new or equivalent to new in both performance and reliability for the Out-of-Warranty Service fee listed below.
    iPad model
    Out-of-Warranty Service Fee
    iPad mini
    $219
    iPad 3rd, 4th generation
    $299
    iPad 2, iPad
    $249
    A $6.95 shipping fee will be added if service is arranged through Apple and requires shipping. All fees are in US dollars and are subject to local tax.
    Certain damage is ineligible for out-of-warranty service, including catastrophic damage, such as the device separating into multiple pieces, and inoperability caused by unauthorized modifications. However, an iPad that has failed due to contact with liquid may be eligible for out-of-warranty service.
    Apple reserves the right to determine whether or not your iPad is eligible for Out-of-Warranty service. Replacement iPads have a 90-day limited hardware warranty or assume the remainder of your standard warranty or AppleCare service contract coverage, whichever is longer. Please see the AppleCare+ for iPad and Apple Repair Terms And Conditions for further details.

  • Vertical red line on screen

    My 15" Macbook Pro has just developed a thin red vertical line on the left side of the screen. What is this problem and how might I fix it?

    I have the same problem. Called Apple and they said to do the equivalent of zapping the PR. Restart and hold down Command + Alt + P + R so the Mac chimes 2 or 3 times.
    This worked for me initially but the line has returned (in a new position) and is no longer fixed by the above. Very annoying - will get on at Apple tomorrow.

  • Red lines on screen where black should be what do i do ?

    So for a few weeks, i have been turning on my lap top and the places where black is supposed to be there is red, and it does not go away..sometimes it will go pink then turn red and will not leave....what do i do or what is wrong with my laptop??

    Hello brenanerzz,
    It sounds like you are seeing some incorrect colors on your MacBook Pro, and I definitely understand your concern with this.
    I found an article with steps to troubleshoot issues with displays.  This article is for internal and external displays, so you can skip any steps referring to an external display.  I recommend reviewing the full article, but this step specifically stands out to me:
    Reset the system
    You can reset the Mac's parameter RAM and SMC.
    You can find the full article here:
    Apple computers: Troubleshooting issues with video on internal or external displays
    http://support.apple.com/kb/ht1573
    Thank you for posting in the Apple Support Communities.
    Best,
    Sheila M.

  • Battety problems - blank screen wit battery sign with red line

    I have the blackberry 8900 curve. Recently when I put my phone on charge it would turn my BB off and turn it self back on again. My battery was about 2% and I put it on charge and the phone turned off but when I looked at my phone the red light came on and then blank screen with a battery sign with a red line through it.
    I got some advice to take out battery, sim card and memory card. Which I did and my BB turned back on. However my battery was still dead so I put it back on charge and it turned off and since then my BB hasn't turned back in. I've left it on charge and nothing.
    Would really appreciate it if someone could help me out on this.
    K.sandhu

    Excellent advice! I just had the same thing happen to me and your post solution fixed my phone.

  • My battery drained. Screen shows battery with red line but doesn't seem to be recharding after 20 min.  Should I wait or do a hard restart? I haven't backedup in ages and don't want to lose pics, contacts etc.

    My battery drained. Pluged in to wall but screen shows battery with red line but doesn't seem to be recharding after 20 min.  Should I wait longer or do a hard restart? I haven't backedup in ages and don't want to lose pics, contacts etc.  Will a hard restart wipe all that out?

    Agree with Richard:
    -Your device needs both the CR and LF. To accomplish this:
    option 1: Concatenate the "end of line" string constant (this is a combination of CR and LF, located in the string pallete) to all your outgoing commands. Make sure in the "Visa configure serial port" the "Termination character enable" flag is false.
    option 2: Concatenate only a CR to your command's strings. Make sure in the "Visa configure serial port" the "Termination character enable" flag is TRUE AND that the termination character is set to 10 (meaning LF) which I think is the default.
    Details can be seen in this link:
    http://digital.ni.com/public.nsf/allkb/862567530005F09C862565BE005AB500
    "Adding Termination Characters to VISA Serial Writes in LabVIEW"
    Interesting would be to configure the serial port to accept not one but two termination characters. The above links refers to the document "Developer Zone Tutorial: Termination Characters in NI-VISA.", where this is supposed to be possible. The document however is 404'ed.
    If someone find a working link please post it.
    Regards

  • My Imac is showing gray screen with red line when booting and restarts again

    My Imac is showing gray screen with red line when booting and restart again, I can load it in windows 7 safe mode with red lines across the display, pls help

    The graphic card is damaged. You can't do anything more than taking your computer to an Apple Store or reseller and getting your graphic card replaced.
    Sometimes, when the graphic card is damaged, operating systems can't start. That's caused because the drivers that make the graphic card work detect an error, telling the operating system that the graphic card is unusable, so the operating system can't start and it restarts. However, you can start in safe mode because operating systems use a basic driver in this startup mode

  • Blank screen showing battery sign with red line - possible solution

    Hi to everybody,
    I had a little issue with my Blackberry curve 8350i, but I think this might go with several models. One day my Blacberry updated an application and restarted, but when restarting suddenly I got a blank screen showing a battery sign with a red line. I took out the battery and put it in again, but no luck. I searched on many forums if anyone experienced the same as me. I found a lot of topics but no solution. I called tech support of my service provide and fortunatelly I talked to a tech guy who was willing to help. He said that this error message usually might appear when the battery is faulty, not original (not my case) or device is not working, but before taking a final statement he wanted me to try something first. He said to take out the battery, the SIM card and any extern memory card. Then to clean any contacts with air. I followed his instructions and after that the device worked again without any problems. I would like to share this experience on this forum maybe this will help other to to solve similar issues.
    Best regards,
    Julix

    Excellent advice! I just had the same thing happen to me and your post solution fixed my phone.

Maybe you are looking for

  • Not getting advertised internet speed

    It's been about 2 weeks since this problem started happening and I can't fix it no matter what I do. I'm currently on the Blast Plus package which should give me 105 Mbps down and 10 Mbps up, but I'm getting no where near that anymore. I used to hit

  • UDConnect & Visual Foxpro 6

    Hi, i am using UDConnect for get datas from ORACLE 10g, that working good, we need extract data from files .dbf version Visual Foxpro 6. We use in Oracle this setting : <b>DriverName</b> Value = oracle.jdbc.driver.OracleDriver <b>URL</b> Value = jdbc

  • J2ME's Java Code Compact issues...

    HI, I am recently trying to integrated some files of JSR 180 with MIDP 2.0/CLDC 1.1. After compiling successfully and the generation of "classes.zip" and "nativeFunctionTable.c" when the java code compactor tries to generate RomJava<platform> file it

  • How to get MAC address list and HDD serial number from Windows and MAC machine?

    Hi, I'm developing a AIR application. I'm implementing the product key mechanishm. I need to identify the users' machines uniquely. I chose MAC address would be a better way. But a computer has list of MAC addresses including LAN card and Wi-Fi card

  • When using the migrate tool to migrate from windows to mac, can you use ethernet to connect the computers to each other?

    When using the migrate tool to migrate from windows to mac, can you use ethernet to connect the computers to each other? In the Migration tool, I was only given the option of choosing the computer when it appeared on the same network, and didn't see