A SIP trunking connection that scales with growth
Since delivering its first inflight Internet experience in 2008, Gogo has grown to over 800 employees in five offices around the country. With 1000s of customers thirsty for in air data connections, its crucial that Gogo is highly available to support its staff and its airline partners globally. Capacity was near its max, but the […]
Read More
This topic first appeared in the Spiceworks Community
Hi,
No as you said you have already created the Trunk between the Sonus and Lync you can use the same trunk. but in the Sonus you have to configure the outbound routes from which Trunk you have to send the calls for the new Trunk provider or the Level3.
check this
https://support.sonus.net/display/UXDOC41/SIP+Trunking+Between+SIP+Border+Elements
Whenever you see a helpful reply, click on Vote As Helpful & click on Mark As Answer if a post answers your question.
Similar Messages
-
Getting support through this site is terrible. Having said that I have been trying to access the store in order to order PS CC and I have been unable to connect. I have an internet connection that works with everyone else. The URL comes up in the browse window and the address simply hangs. This has been going on for the past three hours.
Please read, and reply back here with information https://forums.adobe.com/thread/1499014
-and try some steps such as changing browsers and turning off your firewall for downloads
http://myleniumerrors.com/installation-and-licensing-problems/creative-cloud-error-codes-w ip/
http://helpx.adobe.com/creative-cloud/kb/failed-install-creative-cloud-desktop.html
BLANK Cloud Screen http://forums.adobe.com/message/5484303 may help
-and step by step http://forums.adobe.com/thread/1440508?tstart=0
-and http://helpx.adobe.com/creative-cloud/kb/blank-white-screen-ccp.html
Mac Spinning Wheel https://forums.adobe.com/message/5470608
-Similar in Windows https://forums.adobe.com/message/5853430 -
Swf files that scale with the browser
I uploaded a swf file with dreamweaver as a stand alone window and it works fine. How do I get the swf file to scale larger or smaller as the user adjusts their browser window larger and smaller? I would like to get the swf file to scale along with the browser window. I posted this in dreamweaver but was told this is an action script issue.
I found a simple solution, and I believe it is what you are looking for.
1. In Flash, go to File>Publish Settings
2. Click on the HTML Tab
3. Where is says Dimensions, select Percent
4. Though it is probably default, make sure the width and height are both set to 100.
5. Click ok then go to File>Publish
Now your movie should scale with the browser window.
If you do not have Flash, then you can simple work with this sample code below:
<object width="100%" height="100%" id="xyz" align="middle">
<param name="allowScriptAccess" value="sameDomain" />
<param name="allowFullScreen" value="false" />
<param name="movie" value="xyz.swf" />
<param name="quality" value="high" />
<param name="bgcolor" value="#ffffff" />
<embed src="xyz.swf" quality="high" bgcolor="#ffffff" width="100%" height="100%" name="xyz"
align="middle" allowScriptAccess="sameDomain" allowFullScreen="false" type="application/x-shockwave-flash"
pluginspage="http://www.macromedia.com/go/getflashplayer" />
</object>
Notice how width and height are set to "100%"? That's all you need. -
Wait/notify, await/signal, faster blockingqueue that scales with N threads
Hi,
I have been benchmarking a blockingqueue. It holds 100 items before writers block. It uses not-empty/not-full semaphores. Typical stuff.
I have noticed that with 1 writer and 1 reader threads, using synchronized()+wait/notify is faster than reentrantlock+await/signal.
I tried to find the point (in number of W/R threads) where reentrant lock is better.
For the remainder os the discussion, I must say that I never use 'fair' rentrantlocks: I tested them and they are always slower than synchronized.
So, I always use 'unfair' locks.
The thing is, the tests results are messed up. I mean I would expect a monotonous progression in reentrant lock performance as the number of W/R threads is increasing. But the reality (on a dual core dual opteron) shows strange progressions. Without diving into numbers...
I would like to hear about the experiences of other people relatively to:
-queue implementations and readers semaphore, writers semaphores most efficient patterns.
-scalability observations and implementation choices related to the number of threads to be concurrent.
Of course I have been experimenting with notify()/signal() instead of notifyAll()/signalAll() in order to avoid waking up too many writers/readers that do not stand a chance to perform their enqueue/dequeue without going back to wait()/await() again (in my case, fairness isn't an issue for readers, and for the moment, I accept unfair enqueue from writers). Also, a reader can notify/signal not only a waiting writer but another waiting reader if the queue isn't empty after its own dequeue. I'm about to do the dual notify/signal for writers: not only notify/signal a waiting reader but also another waiting writer if the queue isn't full after its own enqueue.
Of course, this good-intentions implementation ends up notifying/signaling a lot. I'm searching for a new way of thinking, in case I have been blinded by too much obsession on my current implementation...! :-)
Thanks.
PS: for those of you that wonders why I don't use j.u.c array blocking queue, that's because I need:
a) many queues enqueue to be able to notify/signal a single thread (1 thread waiting to read many queues). This implies an externally plugged-in readers (not-empty) semaphore.
b) enqueueMany(array), dequeueMany(int max) ->arrayIn Java 5 ReentrantLock provides much better performance under contention than built-in sync. Conversely built-in uncontended sync is always much faster. In Java 6 contended built-in sync has pulled back some ground on ReentrantLock. So with only two threads it is not surprising that built-in sync is faster.
So the switch over point depends on the level of contention. This is a function of the number of threads (and CPU's) and what they do while holding the lock and between holding the lock.
For evaluating read/write synchronization you need to have a read operation that is relatively long to dominate the cost the heavier read-lock. You also need sufficient parallelism to allow enough concurrent readers to make overall reader "throughput" significant.
Benchmarks are seldom that useful/insightful unless realistic access patterns and workloads are used. -
Does anyone know a USB WIFI connection that works with the Intel Powerbook and OS 10.7.5
I have replaced my AIRPORT EXTREME card because it dropped connection and wouldn't turn back on.
It worked fine for 14 months, but now it is broken again.
I have given up.
I would rather replace a 20-30 dongle everytime rather than the airportexpress card.that should say a $20-$30 dongle.
-
Best Practice to Integrate CER with RedSky E911 Anywhere via SIP Trunk
We are trying to integrate CER 9 with RedSky for V911 using a SIP trunk and need assistance with best practice and configuration. There is very little documentation regarding "best practice" for routing these calls to RedSky. This trunk will be handling the majority of our geographically dispersed company's 911 calls.
My question is: should we use an IPsec tunnel for this? The only reference I found was this: http://www.cisco.com/c/en/us/solutions/collateral/enterprise-networks/virtual-office/deployment_guide_c07-636876.htmlm which recommends an IPsec tunnel for the SIP trunk to Intrado. I would think there are issues with an unsecure SIP trunk for 911 calls. Looking for advice or specifics on how to configure this. Does the SIP trunk require a CUBE or is a CUBE only required for the IPsec tunnel?
Any insight is appreciated.
Thank you.you can use Session Trace in RTMT to check who is disconnecting the call and why.
-
Route pattern to SIP trunk problem
Hello, I have a 2801 router that has been configured with CME and a working SIP connection to my local ISP.
Tested with calls via CME so I know for sure that the SIP config and dial plan is fine on this gateway.
Next I wanted to try out CUCM so I set up a CUCM 8.6 box that is connected to the 2801 router to use as it's SIP gateway.
The only change I made to the gateway router config was to alter the "ip option 150" address so that the phones go to CUCM for their configs etc (which they do with no problems).
Then I set up a SIP trunk in CUCM along with a route pattern which is to use the SIP trunk within the Gateway/Route list option.
But when I make a call that matches this route pattern all I get is the intermittent beep message from the phone. I cannot route calls succesfully through it.
I have checked network connectivity and all is fine. The IP address I specfied in CUCM for the SIP trunk is simply one of the interfaces on the 2801 router and it is definitley reachable.
I also activated "debug ccsip all" on the 2801 gateway router but nothing appears. So it seems like the calls are not even reaching the 2801 gateway ?
Is the problem possibly a conflit between CME on the gateway router and my CUCM ?
Do I need to disable CME somehow on the gateway first ? Or am I not doing something correct in the CUCM config ?
Thank you kindly for any suggestions.
ps. I have attached a couple of screenshots of my config.Hello, thanks for helping.
I activated "debug voice ccapi inout" as well as "debug ccsip all" on the gateway but nothing showed up.
Therefore I deduce the call is not even making it to across the SIP trunk into the gateway router ?
As I am a newbie trying this out for the first time, it is guranteed to be something really simple.
I have included my running config from the gateway router below..
One addition I made was to add an incoming dial peer. That is "dial peer 5, description CUCM SIP trunk".
I set it up with a destination patter 2... to match my phone config on CUCM which have numbering in the 2000 range.
Sorry, I got RTMT up and running but could not get any meaningful results from it. I need to learn up on that.
I did however run a 'dialed number analysis' from CUCM direct and have attached the result. It seems the dialled number "99" is matching the route pattern OK.
So why is it not then moving down the SIP trunk to my gateway and getting picked up by the incoming dial peer ?
Thanks if you guys can offer any more help.
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Router
boot-start-marker
boot system flash:c2801-ipvoicek9-mz.151-2.T0a.bin
boot-end-marker
no aaa new-model
clock timezone nzst 13 0
dot11 syslog
ip source-route
ip dhcp pool DATA_SCOPE
network 192.168.200.0 255.255.255.0
default-router 192.168.200.1
dns-server 8.8.8.8
ip dhcp pool VOICE_SCOPE
network 192.168.100.0 255.255.255.0
default-router 192.168.100.1
option 150 ip 192.168.2.115
ip dhcp pool MGMT_SCOPE
network 192.168.1.0 255.255.255.0
default-router 192.168.1.99
ip cef
ip name-server 4.2.2.2
no ipv6 cef
multilink bundle-name authenticated
voice class codec 1
codec preference 1 g711alaw
codec preference 2 g729r8
codec preference 3 g711ulaw
codec preference 4 ilbc
voice translation-rule 1
rule 1 /^9/ //
voice translation-profile Strip9ToGetOut
translate called 1
voice-card 0
crypto pki token default removal timeout 0
crypto pki trustpoint TP-self-signed-2995340181
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-2995340181
revocation-check none
crypto pki certificate chain TP-self-signed-2995340181
certificate self-signed 01
3082023E 308201A7 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 32393935 33343031 3831301E 170D3733 30363034 31393534
32305A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D32 39393533
34303138 3130819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100C34D C8ECBB53 E01373A3 2E286B78 2D23042B 1C8588B1 A7861899 BA1C6860
AE1D7868 2A59E3BC 54D0A457 8FFDE27F C09104E5 C7A429F3 74CD9DA8 4A980366
675CC27C CDB94838 821CC05F 2C0AC2BC D882C132 6CAA1FA6 6DA740E4 562428B1
12B741F1 A50C9246 4CC35EDA DEE1D038 3883BB35 A91ABF8B 483E4160 F5FA4B5A
9A570203 010001A3 66306430 0F060355 1D130101 FF040530 030101FF 30110603
551D1104 0A300882 06526F75 74657230 1F060355 1D230418 30168014 72119640
F3396E1F E4168086 D31D8619 0D8337FF 301D0603 551D0E04 16041472 119640F3
396E1FE4 168086D3 1D86190D 8337FF30 0D06092A 864886F7 0D010104 05000381
81003B5A 29DE3A1E C5AB6092 E8D90650 C80752FC 0AAC93FD C5DE3D69 071B08FA
D4013232 81CA07E7 15F90190 6A3AD6A0 1D05F0F2 13479568 888332A5 F81E2681
7DA44095 4D11CFB7 CA79579A 8D95DE54 7B00173C E2C50573 A310C8C9 1487FEFC
CE35B66E 9EF94CFA 8D6D6DCD ADC78132 2709F198 6DF2F0FA D80CC088 D0C4C7D1 080B
quit
license udi pid CISCO2801 sn FTX0947W07M
username xxx privilege 15 password 0 xxx
interface FastEthernet0/0
ip address 192.168.3.50 255.255.255.0
duplex auto
speed auto
interface FastEthernet0/1
no ip address
duplex auto
speed auto
interface FastEthernet0/1.2
encapsulation dot1Q 2
ip address 192.168.2.1 255.255.255.0
interface FastEthernet0/1.99
encapsulation dot1Q 99
ip address 192.168.1.99 255.255.255.0
interface FastEthernet0/1.100
description voice_VLAN
encapsulation dot1Q 100
ip address 192.168.100.1 255.255.255.0
interface FastEthernet0/1.200
description data_VLAN
encapsulation dot1Q 200
ip address 192.168.200.1 255.255.255.0
ip forward-protocol nd
ip http server
ip http authentication local
ip http secure-server
ip route 0.0.0.0 0.0.0.0 192.168.3.1
logging esm config
tftp-server flash:/phone/7940-7960/P00307020200.bin alias P00307020200.bin
tftp-server flash:/phone/7940-7960/P00307020200.loads alias P00307020200.loads
tftp-server flash:/phone/7940-7960/P00307020200.sb2 alias P00307020200.sb2
tftp-server flash:/phone/7940-7960/P00307020200.sbn alias P00307020200.sbn
control-plane
mgcp fax t38 ecm
dial-peer voice 1 voip
description local_7_Digit_Calling
translation-profile outgoing Strip9ToGetOut
destination-pattern 9[2-9]......
session protocol sipv2
session target ipv4:203.184.16.2
voice-class codec 1
dial-peer voice 2 voip
description international_calling
translation-profile outgoing Strip9ToGetOut
destination-pattern 900T
session protocol sipv2
session target ipv4:203.184.16.2
voice-class codec 1
dial-peer voice 3 voip
description national_calling
translation-profile outgoing Strip9ToGetOut
destination-pattern 90[34679].......
session protocol sipv2
session target ipv4:203.184.16.2
voice-class codec 1
dial-peer voice 4 voip
translation-profile outgoing Strip9ToGetOut
destination-pattern 90[34679].......
dial-peer voice 5 voip
description CUCM SIP trunk
destination-pattern 2...
session protocol sipv2
session target ipv4:192.168.2.115
voice-class codec 1
sip-ua
authentication username xxxxxxxxxx password xxxxxxxx
060
telephony-service
max-ephones 10
max-dn 20
ip source-address 192.168.1.99 port 2000
load 7960-7940 P00307020200
max-conferences 4 gain -6
transfer-system full-consult
create cnf-files version-stamp Jan 01 2002 00:00:00
ephone-dn 1 dual-line
number 1000
name Lydia Francis
ephone-dn 2 dual-line
number 1001
name Leah Francis
ephone-dn 3 dual-line
number 1002
n
ephone-dn 4 dual-line
number 1003
ephone 1
mac-address C80A.A970.01DE
type CIPC
button 2:2
ephone 2
mac-address 000C.3070.8705
button 1:1 2:15
ephone 3
mac-address 000C.8546.5954
button 1:3 2:15
line con 0
logging synchronous
line aux 0
line vty 0 4
privilege level 15
login local
transport input telnet ssh
scheduler allocate 20000 1000
ntp server 195.43.74.123
end -
Hello,
anyone knows what is the trace in RTMT when a sip trunk connected to CUCM 9 resets manually. I am checkin in logs but there is so much logs in it, if ai know this trace i can "find" in logs.
Thaks Anna.You need to look at cucm audit logs for this not RTMT
-
Connect to server with specified user account
I want my mac connect to some network storage when it start up. So i created a automator app with "get specified servers" and "connect to servers".
Some folders of a servers was set to allow guest to view content only. my mac automatically connect that folder as guest.
So I would like to know how to set the automator to connect that folder with specified account, so that i can have right to right and write.
Thanks.Using the Finder, mount the volume from the server.
Using the Finder, create a Mac OS X Alias of the mounted volume.
This will capture the account used to mount the volume.
If you want this volume mounted when you login, put the
alias in your System Preferences -> Accounts -> Startup Items
If you want to open it via an Automator workflow, then just have
Automator open the alias, and the alias will do the rest. -
Issue with instant ringback when using sip trunk to SP
Hi all,
We use CUCM 8.0.2.
We have a SIP trunk to a SP connected via one of our Cisco 2911 routers configured as a CUBE.
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.0(1)M3, RELEASE SOFTWARE (fc2)
c2900-universalk9-mz.SPA.150-1.M3.bin
Cisco CISCO2911/K9 (revision 1.0)
Technology Package License Information for Module:'c2900'
Technology Technology-package
Current Type
ipbase ipbasek9 Permanent
security securityk9 Permanent
uc uck9 Permanent
data None None
We also have several ISDN lines that run out via various Cisco routers configured as H323 gateways.
We use 7945 and CIPC for our phones.
We're having an issue with calls going via the SIP trunk where we hear ringing instantly after dialling - but before the actual device at the other end starts ringing (considerable difference).
Using the SIP trunk: If I make a call to my mobile phone - I hear ringing instantly - about 3 rings before my mobile phone actually starts ringing - undesireable.
Using H323 gateway: If I make a call to my mobile phone - I hear silence for a bit - then ringing when the mobile starts ringing - desired.
Using SIP trunk: If I make a call to a landline that is ready - it rings instantly for at least 1 ring - before the actual phone I'm calling starts ringing - undesireable.
Using H323 gateway: There is a momentary pause before hearing ringing on my phone and the phone I dialled - desired.
Using SIP trunk: If I make a call to a landline that is off-hook (with no call-waiting/etc.) - it rings once and then returns the busy signal (the worst issue) - undesireable.
Using H323 gateway: There is a momentary pause before hearing busy signal - desired.
Phone to phone internally (same network): Operates as expected (instantly rings locally and on the phone I'm calling). Between phones that utilise the SIP trunk and phones that utilise the H323 gateways within the same network - communication is instant and as expected.
Any ideas why this happens and how to stop it?
I want it to not ring until the situation is known and that it can provide the appropriate feedback (ringing/busy/etc.).
Some possibly relevant config (note that there is a known bug with this IOS that meant I had to declare the codec in each dial-peer as the voice class would not work):
voice service voip
address-hiding
mode border-element
allow-connections sip to sip
sip
bind control source-interface GigabitEthernet0/0
bind media source-interface GigabitEthernet0/0
header-passing error-passthru
early-offer forced
midcall-signaling passthru
interface GigabitEthernet0/0
ip address x.x.x.x 255.255.255.252
ip access-group acl.SIP-IN in
no ip redirects
no ip unreachables
ip verify unicast reverse-path
ip virtual-reassembly
duplex full
speed 100
no cdp enable
gateway
timer receive-rtp 1200
sip-ua
connection-reuse
gatekeeper
shutdown
dial-peer voice 1 voip
description *** INBOUND CALLS FROM CARRIER ***
translation-profile incoming SIPTRUNK-INCOMING
session protocol sipv2
incoming called-number #blah blah#
dtmf-relay rtp-nte
codec g711alaw
ip qos dscp cs5 media
no vad
dial-peer voice 61 voip
description **** WA, SA AND NT NUMBERS ****
destination-pattern 0[8]........
session protocol sipv2
session target ipv4:<MY SP's SIP SERVER>
incoming called-number 0[8]........
dtmf-relay rtp-nte
codec g711alaw
ip qos dscp cs5 media
no vad
dial-peer voice 81 voip
description **** MOBILE NUMBERS ****
destination-pattern 0[4]........
session protocol sipv2
session target ipv4:<MY SP's SIP SERVER>
incoming called-number 0[4]........
dtmf-relay rtp-nte
codec g711alaw
ip qos dscp cs5 media
no vad
dial-peer voice 500 voip
description *** INBOUND SIP TRUNK TO CUCM PUB ***
translation-profile outgoing SIPTRUNK-CALLING-ADD-0
preference 1
destination-pattern 5[12]..
session protocol sipv2
session target ipv4:<OUR CUCM PUBLISHER IP>
dtmf-relay rtp-nte
codec g711alaw
ip qos dscp cs5 media
no vad
Any help or a point in the right direction would be greatly appreciated.
Cheers,
BrettI ended up resolving this issue as follows:
In CUCM, under Device > Device Settings > SIP Profile.
I modifed the profile relevant to my SIP trunk, under the "Trunk Specific Configuration", I set "SIP Rel1XX Options" from "Disabled" to "Send PRACK if 1xx Contains SDP".
Now, I get the expected delay before hearing ringback.
Solved! -
Lync 2013 with SIP trunk with panasonic kx-tde200
Hi
My company has installed a panasonic ip-pbx kx-tde for multiline with 100 number range for telephone service.
Now my company is going to replace multiline by sip trunk . It will still work with Panasonic pbx box just need to reprogramme to be able to connected to the sip proxy which is managed by internet service provider.
For this scenario , would Lync 2013 voice work if I just add PSTN gateway which is the ip of panasonic pbx address to the frontend in topology ? Or I may need a mediation server as a must requirement to make lync voice work?
Thanks
WenFeiMedia bypass allow a call to basically skip the mediation server once it's established and go directly from gateway (in this case the PBX) and the endpoint (the telephone handset or Lync client) More information here: http://technet.microsoft.com/en-us/library/gg398719.aspx
By having this (if your PBX supports it) you reduce the load on the mediation servers. Before you go too far down the road also make sure that your PBX supports SIP trunks that are SIP over TCP (as Lync doesn't work with SIP over UDP)
Sort of, the easiest way is to add the .com as an additional SIP domain in Topology builder, you will need to create DNS records for it (both internal and external) and you will need to reissue the certs with additional SANs to support the second domain.
YOu will also need to update all the users to use the new suffix of xxx.com. So it's not a small task.
If this helped you please click "Vote As Helpful" if it answered your question please click "Mark As Answer" | Blog
www.lynced.com.au | Twitter
@imlynced -
Unity Connection SIP trunk integration vs alerting name
Hello,
I have been implementing a Unity Connecion 8.6 with a CUCM cluster 8.6 via a SIP trunk.
The previous implemention of the Unity server was set up using voicemail ports;
When users used to call the voicemail pilot number, we were able to configure an alerting name on the vm ports, saying (to VoiceMail) for example.
I am looking for a solution for the new implementation via the SIP trunk. I just want users to see 'to VoiceMail' on their phone when they call the Unity Connection system.
Thanks for the help!
Best regards,
AntoineI have found the solution:
If you want to dispaly a name such as Voicemail, etc you can change that in Unity Connection under Port Group --> Advanced Settings --> "Remote-Party-ID"
cheers! -
Unity Connection not passing CallerID to CUCM over SIP Trunk
I'm trying to get CallerID working for Unity Connection Device Notification (and it seems everything else), however, when I run UC Remote Port Status Monitor and the Call-Out goes to CUCM for the Device Notification, no caller ID is presented to the CUCM SIP trunk.
06:06:02, New Call, CalledId=, RedirectingId=, Origin=16, Reason=1024, CallGuid=,
CallerName=, LastRedirectingId=, LastRedirectingReason=1024, PortDisplayName=LFC_CUCM-1-134,
[Origin=Unknown],[Reason=Unknown]
06:06:02,
Dialing '99254753'
06:06:32, Idle
06:06:33, Idle
Therefore, the out-going call to the PRI PSTN is:
10:59:01.005: ISDN Se0/0/0:23 Q931: TX -> SETUP pd = 8 callref = 0x5B03
Sending Complete
Bearer Capability i = 0x8090A2
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98397
Exclusive, Channel 23
Calling Party Number i = 0x0081, N/A
Plan:Unknown, Type:Unknown
Called Party Number i = 0xC1, '9254753'
Plan:ISDN, Type:Subscriber(local)
*Dec 6 10:59:01.513: ISDN Se0/0/0:23 Q931: RX <- CALL_PR
I've looked through my SIP trunk on the CUCM side and for Inbound Calls, Connected Line ID and Presentation Name are set to "allowed" or "default" doesn't make a difference. RTMT Port Status also shows no "caller", so I'm thinking there is some way to set or allow the calling number on the Unity Connection (8.5) side.
Oddly enough, I also noticed that in Unity Connection> Telephony Integrations > Port Group, if I change the Contact Line Name from nothing to "Unity" (or whatever), the Q931 debug outbound doesn't show ANY "Calling Party Numer - = XXXXX" and the carrier throws out the BTN as the ANI.
10:46:00.837: ISDN Se0/0/0:23 Q931: TX -> SETUP pd = 8 callref = 0x5AFF
Sending Complete
Bearer Capability i = 0x8090A2
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98397
Exclusive, Channel 23
Called Party Number i = 0xC1, '9254753'
Plan:ISDN, Type:Subscriber(local)
Any ideas on where/how CallerID comes from, on Unity Connection with a SIP integration?
THANKS!!
Mike.I did not- my work around has been to put in a name for Contact Line Name under Port Group Basics Switch configuration in Unity Connection- this for some reason keeps CUCM from sending ANI TYPE/PLAN information in the Q931 message, and my carrier then sends a default ANI of the circuit's BTN. When I have time, I'll open up a TAC ticket.
Mike. -
SIP Trunk - No voice with Single Number Reach
Hi Community.
I setup SIP Trunk with the CCA. Everything is working Call In and Call Out. Call Forward and so on.
But with Single Number reach is something wrong. The mobile phone is ringing and I can get the call, but I hear not any voice.
Can someone please help me out? Below the config.
version 15.1
parser config cache interface
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
service internal
service compress-config
service sequence-numbers
dot11 ssid cisco-data
vlan 1
authentication open
dot11 ssid cisco-voice
vlan 100
authentication open
ip source-route
ip cef
ip dhcp relay information trust-all
ip dhcp excluded-address 10.1.1.1 10.1.1.9
ip dhcp excluded-address 10.1.1.241 10.1.1.255
ip dhcp pool phone
network 10.1.1.0 255.255.255.0
default-router 10.1.1.1
option 150 ip 10.1.1.1
ip domain name site1.365873.trk.ipvoip.ch
ip name-server 8.8.8.8
ip inspect WAAS flush-timeout 10
ip inspect name SDM_LOW dns
ip inspect name SDM_LOW ftp
ip inspect name SDM_LOW h323
ip inspect name SDM_LOW https
ip inspect name SDM_LOW icmp
ip inspect name SDM_LOW imap
ip inspect name SDM_LOW pop3
ip inspect name SDM_LOW netshow
ip inspect name SDM_LOW rcmd
ip inspect name SDM_LOW realaudio
ip inspect name SDM_LOW rtsp
ip inspect name SDM_LOW esmtp
ip inspect name SDM_LOW sqlnet
ip inspect name SDM_LOW streamworks
ip inspect name SDM_LOW tftp
ip inspect name SDM_LOW tcp router-traffic
ip inspect name SDM_LOW udp router-traffic
ip inspect name SDM_LOW vdolive
no ipv6 cef
multilink bundle-name authenticated
stcapp ccm-group 1
stcapp
isdn switch-type basic-net3
voice call send-alert
voice rtp send-recv
voice service voip
ip address trusted list
ipv4 0.0.0.0 0.0.0.0
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
supplementary-service h450.12
no supplementary-service sip refer
fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback pass-through g711ulaw
sip
registrar server expires max 3600 min 3600
localhost dns:site1.365873.trk.ipvoip.ch
no update-callerid
voice class codec 1
codec preference 1 g711alaw
voice register global
mode cme
source-address 10.1.1.1 port 5060
load 9971 sip9971.9-2-2
load 9951 sip9951.9-2-2
load 8961 sip8961.9-2-2
timezone 23
voice source-group CCA_SIP_SOURCE_GROUP_CUE_CME
access-list 2
translation-profile incoming SIP_Incoming
voice source-group CCA_SIP_SOURCE_GROUP_EXTERNAL
access-list 3
voice translation-rule 9
rule 1 /0041449475090/ /90/
rule 2 /0041449475091/ /91/
rule 3 /0041449475092/ /92/
rule 4 /0041449475093/ /93/
rule 5 /0041449475094/ /94/
rule 6 /0041449475095/ /95/
rule 7 /0041449475096/ /96/
rule 8 /0041449475097/ /97/
rule 9 /0041449475098/ /98/
rule 10 /0041449475099/ /99/
voice translation-rule 410
rule 1 /^0\(.*\)/ /\1/
rule 15 /^..$/ /0041449475090/
voice translation-rule 411
rule 1 /^0\(.*\)/ /ABCD0\1/
voice translation-rule 412
rule 1 /^ABCD\(.*\)/ /\1/
voice translation-rule 422
rule 15 /^ABCD\(.*\)/ /\1/
voice translation-rule 1000
rule 1 /.*/ //
voice translation-rule 1111
rule 1 /^9\([1-9]\)$/ /004144947509\1/
rule 15 /^..$/ /0041449475090/
voice translation-rule 1112
rule 1 /^0/ //
voice translation-rule 2000
rule 1 /0041449475098/ /98/
voice translation-rule 2001
rule 1 /0041449475097/ /97/
voice translation-rule 2002
rule 1 /^6/ //
voice translation-rule 2222
voice translation-profile AA_Profile
translate called 2001
voice translation-profile CALLER_ID_TRANSLATION_PROFILE
translate calling 1111
voice translation-profile CallBlocking
translate called 2222
voice translation-profile OUTGOING_TRANSLATION_PROFILE
translate called 1112
voice translation-profile PSTN_CallForwarding
translate redirect-target 410
translate redirect-called 410
voice translation-profile PSTN_Outgoing
translate calling 1111
translate called 1112
translate redirect-target 410
translate redirect-called 410
voice translation-profile SIP_Called_9
translate calling 3265
translate called 9
voice translation-profile SIP_Incoming
translate called 411
voice translation-profile SIP_Passthrough
translate called 412
voice translation-profile SIP_Passthrough_CallBlocking
translate called 422
voice translation-profile VM_Profile
translate called 2000
voice translation-profile XFER_TO_VM_PROFILE
translate redirect-called 2002
voice translation-profile nondialable
translate called 1000
voice-card 0
dspfarm
dsp services dspfarm
fax interface-type fax-mail
license udi pid UC540W-BRI-K9 sn FGL163220SL
archive
log config
logging enable
logging size 600
hidekeys
username admin privilege 15 secret xxx
username xxx password 0 ""
username xxx password 0 ""
ip tftp source-interface Loopback0
bridge irb
interface Loopback0
description $FW_INSIDE$
ip address 10.1.10.2 255.255.255.252
ip access-group 101 in
ip nat inside
ip virtual-reassembly in
interface FastEthernet0/0
description $FW_OUTSIDE$
no ip address
ip inspect SDM_LOW out
ip virtual-reassembly in
ip verify unicast reverse-path
load-interval 30
shutdown
duplex auto
speed auto
interface Integrated-Service-Engine0/0
description cue is initialized with default IMAP group
ip unnumbered Loopback0
ip nat inside
ip virtual-reassembly in
service-module ip address 10.1.10.1 255.255.255.252
service-module ip default-gateway 10.1.10.2
interface FastEthernet0/1/0
no ip address
macro description cisco-desktop
spanning-tree portfast
interface FastEthernet0/1/1
switchport voice vlan 100
no ip address
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/2
switchport voice vlan 100
no ip address
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/3
switchport voice vlan 100
no ip address
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/4
switchport voice vlan 100
no ip address
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/5
switchport voice vlan 100
no ip address
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/6
switchport voice vlan 100
no ip address
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/7
switchport voice vlan 100
no ip address
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/8
no ip address
macro description cisco-desktop
spanning-tree portfast
interface BRI0/1/0
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn sending-complete
isdn static-tei 0
interface BRI0/1/1
no ip address
shutdown
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn sending-complete
isdn static-tei 0
interface Dot11Radio0/5/0
no ip address
ssid cisco-data
ssid cisco-voice
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
station-role root
antenna receive right
antenna transmit right
interface Dot11Radio0/5/0.1
encapsulation dot1Q 1 native
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio0/5/0.100
encapsulation dot1Q 100
bridge-group 100
bridge-group 100 subscriber-loop-control
bridge-group 100 spanning-disabled
bridge-group 100 block-unknown-source
no bridge-group 100 source-learning
no bridge-group 100 unicast-flooding
interface Vlan1
no ip address
bridge-group 1
bridge-group 1 spanning-disabled
interface Vlan100
no ip address
bridge-group 100
bridge-group 100 spanning-disabled
interface BVI1
description $FW_INSIDE$
ip address 192.168.10.2 255.255.255.0
ip access-group 102 in
ip nat inside
ip virtual-reassembly in
interface BVI100
description $FW_INSIDE$
ip address 10.1.1.1 255.255.255.0
ip access-group 103 in
ip nat inside
ip virtual-reassembly in
ip forward-protocol nd
ip http server
ip http authentication local
ip http secure-server
ip http path flash:/gui
ip dns server
ip nat inside source list 1 interface FastEthernet0/0 overload
ip route 0.0.0.0 0.0.0.0 192.168.10.1
ip route 10.1.10.1 255.255.255.255 Integrated-Service-Engine0/0
access-list 1 remark SDM_ACL Category=2
access-list 1 permit 10.1.1.0 0.0.0.255
access-list 1 permit 192.168.10.0 0.0.0.255
access-list 1 permit 10.1.10.0 0.0.0.3
access-list 2 remark CCA_SIP_SOURCE_GROUP_ACL_INTERNAL
access-list 2 remark SDM_ACL Category=1
access-list 2 permit 192.168.10.2
access-list 2 permit 10.1.10.0 0.0.0.3
access-list 2 permit 192.168.10.0 0.0.0.255
access-list 2 permit 10.1.1.0 0.0.0.255
access-list 3 remark CCA_SIP_SOURCE_GROUP_ACL_EXTERNAL
access-list 3 remark SDM_ACL Category=1
access-list 3 permit 212.147.47.216
access-list 3 deny any
access-list 100 remark auto generated by SDM firewall configuration
access-list 100 remark SDM_ACL Category=1
access-list 100 deny ip 192.168.10.0 0.0.0.255 any
access-list 100 deny ip host 255.255.255.255 any
access-list 100 deny ip 127.0.0.0 0.255.255.255 any
access-list 100 permit ip any any
access-list 101 remark auto generated by SDM firewall configuration##NO_ACES_8##
access-list 101 remark SDM_ACL Category=1
access-list 101 permit tcp 10.1.1.0 0.0.0.255 eq 2000 any
access-list 101 permit udp 10.1.1.0 0.0.0.255 eq 2000 any
access-list 101 deny ip 10.1.1.0 0.0.0.255 any
access-list 101 deny ip 192.168.10.0 0.0.0.255 any
access-list 101 deny ip 192.168.1.0 0.0.0.255 any
access-list 101 deny ip host 255.255.255.255 any
access-list 101 deny ip 127.0.0.0 0.255.255.255 any
access-list 101 permit ip any any
access-list 102 remark auto generated by SDM firewall configuration##NO_ACES_6##
access-list 102 remark SDM_ACL Category=1
access-list 102 deny ip 10.1.10.0 0.0.0.3 any
access-list 102 deny ip 10.1.1.0 0.0.0.255 any
access-list 102 deny ip 192.168.1.0 0.0.0.255 any
access-list 102 deny ip host 255.255.255.255 any
access-list 102 deny ip 127.0.0.0 0.255.255.255 any
access-list 102 permit ip any any
access-list 103 remark auto generated by SDM firewall configuration##NO_ACES_8##
access-list 103 remark SDM_ACL Category=1
access-list 103 permit tcp 10.1.10.0 0.0.0.3 any eq 2000
access-list 103 permit udp 10.1.10.0 0.0.0.3 any eq 2000
access-list 103 deny ip 10.1.10.0 0.0.0.3 any
access-list 103 deny ip 192.168.10.0 0.0.0.255 any
access-list 103 deny ip 192.168.1.0 0.0.0.255 any
access-list 103 deny ip host 255.255.255.255 any
access-list 103 deny ip 127.0.0.0 0.255.255.255 any
access-list 103 permit ip any any
access-list 104 remark auto generated by SDM firewall configuration##NO_ACES_14##
access-list 104 remark SDM_ACL Category=1
access-list 104 deny ip 10.1.10.0 0.0.0.3 any
access-list 104 deny ip 10.1.1.0 0.0.0.255 any
access-list 104 permit ip any any
access-list 104 permit udp host 8.8.8.8 eq domain any
access-list 104 permit icmp any any echo-reply
access-list 104 permit icmp any any time-exceeded
access-list 104 permit icmp any any unreachable
access-list 104 deny ip 10.0.0.0 0.255.255.255 any
access-list 104 deny ip 172.16.0.0 0.15.255.255 any
access-list 104 deny ip 192.168.0.0 0.0.255.255 any
access-list 104 deny ip 127.0.0.0 0.255.255.255 any
access-list 104 deny ip host 255.255.255.255 any
access-list 104 deny ip host 0.0.0.0 any
access-list 104 deny ip any any
control-plane
bridge 1 route ip
bridge 100 route ip
voice-port 0/0/0
cptone CH
station-id name FAX
station-id number 99
caller-id enable
voice-port 0/0/1
cptone CH
shutdown
caller-id enable
voice-port 0/0/2
cptone CH
shutdown
caller-id enable
voice-port 0/0/3
cptone CH
shutdown
caller-id enable
voice-port 0/1/0
compand-type a-law
cptone CH
bearer-cap Speech
voice-port 0/1/1
compand-type a-law
cptone CH
bearer-cap Speech
voice-port 0/4/0
auto-cut-through
signal immediate
input gain auto-control -15
description Music On Hold Port
sccp local Loopback0
sccp ccm 10.1.1.1 identifier 1 version 4.0
sccp
sccp ccm group 1
associate ccm 1 priority 1
associate profile 2 register mtpa4934c6ee4e0
dspfarm profile 2 transcode
description CCA transcoding for SIP Trunk VTX
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
maximum sessions 10
associate application SCCP
dial-peer cor custom
name internal
name local
name local-plus
name international
name national
name national-plus
name emergency
name toll-free
dial-peer cor list call-internal
member internal
dial-peer cor list call-local
member local
dial-peer cor list call-local-plus
member local-plus
dial-peer cor list call-national
member national
dial-peer cor list call-national-plus
member national-plus
dial-peer cor list call-international
member international
dial-peer cor list call-emergency
member emergency
dial-peer cor list call-toll-free
member toll-free
dial-peer cor list user-internal
member internal
member emergency
dial-peer cor list user-local
member internal
member local
member emergency
member toll-free
dial-peer cor list user-local-plus
member internal
member local
member local-plus
member emergency
member toll-free
dial-peer cor list user-national
member internal
member local
member local-plus
member national
member emergency
member toll-free
dial-peer cor list user-national-plus
member internal
member local
member local-plus
member national
member national-plus
member emergency
member toll-free
dial-peer cor list user-international
member internal
member local
member local-plus
member international
member national
member national-plus
member emergency
member toll-free
dial-peer voice 1 pots
destination-pattern 99
port 0/0/0
no sip-register
dial-peer voice 2 pots
port 0/0/1
no sip-register
dial-peer voice 3 pots
port 0/0/2
no sip-register
dial-peer voice 4 pots
port 0/0/3
no sip-register
dial-peer voice 5 pots
description ** MOH Port **
destination-pattern ABC
port 0/4/0
no sip-register
dial-peer voice 6 pots
description tcatch all dial peer for BRI/PRIv
translation-profile incoming nondialable
incoming called-number .%
direct-inward-dial
dial-peer voice 50 pots
description ** incoming dial peer **
incoming called-number ^AAAA$
direct-inward-dial
port 0/1/0
dial-peer voice 51 pots
description ** incoming dial peer **
incoming called-number ^AAAA$
direct-inward-dial
port 0/1/1
dial-peer voice 2000 voip
description ** cue voicemail pilot number **
translation-profile outgoing XFER_TO_VM_PROFILE
destination-pattern 98
b2bua
session protocol sipv2
session target ipv4:10.1.10.1
voice-class sip outbound-proxy ipv4:10.1.10.1
dtmf-relay rtp-nte
codec g711ulaw
no vad
dial-peer voice 2001 voip
description ** cue auto attendant number **
translation-profile outgoing PSTN_CallForwarding
destination-pattern 97
b2bua
session protocol sipv2
session target ipv4:10.1.10.1
voice-class sip outbound-proxy ipv4:10.1.10.1
dtmf-relay rtp-nte
codec g711ulaw
no vad
dial-peer voice 2012 voip
description ** cue prompt manager number **
translation-profile outgoing PSTN_CallForwarding
destination-pattern 96
b2bua
session protocol sipv2
session target ipv4:10.1.10.1
voice-class sip outbound-proxy ipv4:10.1.10.1
dtmf-relay rtp-nte
codec g711ulaw
no vad
dial-peer voice 1000 voip
permission term
description ** Incoming call from SIP trunk (VTX) **
session protocol sipv2
session target sip-server
incoming called-number .%
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
fax rate 14400
fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback pass-through g711ulaw
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1001 voip
corlist outgoing call-local
description ** star code to SIP trunk (VTX) **
destination-pattern *..
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
fax rate 14400
fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback pass-through g711ulaw
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1003 voip
description ** Passthrough Inbound Calls for PSTN from CUE **
translation-profile incoming SIP_Passthrough
b2bua
session protocol sipv2
session target ipv4:10.1.10.1
incoming called-number ABCDT
dtmf-relay rtp-nte
codec g711ulaw
no vad
dial-peer voice 1005 voip
description ** Passthrough Inbound Calls for MWI from CUE **
b2bua
session protocol sipv2
session target ipv4:10.1.10.1
incoming called-number A80T
dtmf-relay rtp-nte
codec g711ulaw
no vad
dial-peer voice 1009 voip
description ** Passthrough Inbound Calls for Internal Extensions from CUE **
b2bua
session protocol sipv2
session target ipv4:10.1.10.1
incoming called-number ^..$
dtmf-relay rtp-nte
codec g711ulaw
no vad
dial-peer voice 1033 voip
corlist outgoing call-local
description **CCA*Switzerland*Short Code Services**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 0187
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1042 voip
corlist outgoing call-emergency
description **CCA*Switzerland*Ambulance / Poisioning**
translation-profile outgoing CALLER_ID_TRANSLATION_PROFILE
preference 1
destination-pattern 0014[45]
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1041 voip
corlist outgoing call-emergency
description **CCA*Switzerland*REGA Air Rescue**
translation-profile outgoing CALLER_ID_TRANSLATION_PROFILE
preference 1
destination-pattern 00333333333
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1025 voip
corlist outgoing call-national
description **CCA*Switzerland*National Destination Numbers**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 00[789]1.......
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1020 voip
corlist outgoing call-national
description **CCA*Switzerland*Regional Announcement VM**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 01600
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1040 voip
corlist outgoing call-emergency
description **CCA*Switzerland*REGA Air Rescue**
translation-profile outgoing CALLER_ID_TRANSLATION_PROFILE
preference 1
destination-pattern 000333333333
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1043 voip
corlist outgoing call-emergency
description **CCA*Switzerland*Ambulance / Poisioning**
translation-profile outgoing CALLER_ID_TRANSLATION_PROFILE
preference 1
destination-pattern 014[45]
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1035 voip
corlist outgoing call-national
description **CCA*Switzerland*Mobile Numbers**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 007[46789].......
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1024 voip
corlist outgoing call-national-plus
description **CCA*Switzerland*Personal Numbering**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 00878......
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1029 voip
corlist outgoing call-national
description **CCA*Switzerland*Voicemail Access**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 00860.........
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1036 voip
corlist outgoing call-national
description **CCA*Switzerland*VPN Access**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 00869.............
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1027 voip
corlist outgoing call-national-plus
description **CCA*Switzerland*Premium Rate (Business)**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 00900......
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1026 voip
corlist outgoing call-national
description **CCA*Switzerland*Test Numbers**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 00868T
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1034 voip
corlist outgoing call-national-plus
description **CCA*Switzerland*Shared Cost numbers**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 0084[0248]......
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1038 voip
corlist outgoing call-emergency
description **CCA*Switzerland*Emergency**
translation-profile outgoing CALLER_ID_TRANSLATION_PROFILE
preference 1
destination-pattern 0011[278]
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1037 voip
corlist outgoing call-toll-free
description **CCA*Switzerland*Toll Free Numbers**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 00800......
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1039 voip
corlist outgoing call-emergency
description **CCA*Switzerland*Emergency**
translation-profile outgoing CALLER_ID_TRANSLATION_PROFILE
preference 1
destination-pattern 011[278]
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1032 voip
corlist outgoing call-national
description **CCA*Switzerland*National Destination Numbers**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 00[23456]........
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1023 voip
corlist outgoing call-international
description **CCA*Switzerland*International Calls**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 000T
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1031 voip
description **CCA*Switzerland*Premium Rate (Social)**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 0090[16]......
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1030 voip
corlist outgoing call-national
description **CCA*Switzerland*Short Code**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 014[0357]
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1045 voip
corlist outgoing call-emergency
description **CCA*Switzerland*REGA/Glaciers Air Rescue**
translation-profile outgoing CALLER_ID_TRANSLATION_PROFILE
preference 1
destination-pattern 0141[45]
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1028 voip
corlist outgoing call-national-plus
description **CCA*Switzerland*Directory Enquiries**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 018[15].
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1021 voip
corlist outgoing call-national
description **CCA*Switzerland*Short Code**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 011[45].
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1022 voip
corlist outgoing call-national
description **CCA*Switzerland*Short Code Services**
translation-profile outgoing PSTN_Outgoing
preference 1
destination-pattern 01[67].
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 1044 voip
corlist outgoing call-emergency
description **CCA*Switzerland*REGA/Glaciers Air Rescue**
translation-profile outgoing CALLER_ID_TRANSLATION_PROFILE
preference 1
destination-pattern 00141[45]
session protocol sipv2
session target sip-server
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
dial-peer voice 2002 voip
description ** cue voicemail PSTN number **
translation-profile outgoing VM_Profile
destination-pattern xxx$
b2bua
session protocol sipv2
session target ipv4:10.1.10.1
voice-class sip outbound-proxy ipv4:10.1.10.1
dtmf-relay rtp-nte
codec g711ulaw
no vad
dial-peer voice 2003 voip
description ** cue auto attendant PSTN number **
translation-profile outgoing AA_Profile
destination-pattern xxx$
b2bua
session protocol sipv2
session target ipv4:10.1.10.1
voice-class sip outbound-proxy ipv4:10.1.10.1
dtmf-relay rtp-nte
codec g711ulaw
no vad
dial-peer voice 1110 pots
preference 9
destination-pattern xxx
port 0/0/0
no sip-register
dial-peer voice 3006 voip
description SIP
translation-profile incoming SIP_Called_9
session protocol sipv2
session target sip-server
incoming called-number xxx.
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
no dial-peer outbound status-check pots
sip-ua
keepalive target dns:site1.365873.trk.ipvoip.ch
authentication username xxx password 7 xxx
no remote-party-id
retry invite 2
retry register 10
timers connect 100
timers keepalive active 100
registrar dns:site1.365873.trk.ipvoip.ch expires 3600
sip-server dns:site1.365873.trk.ipvoip.ch
host-registrar
telephony-service
sdspfarm units 5
sdspfarm transcode sessions 10
sdspfarm tag 2 mtpa4934c6ee4e0
video
fxo hook-flash
max-ephones 40
max-dn 300
ip source-address 10.1.1.1 port 2000
auto assign 1 to 1 type bri
calling-number initiator
service phone videoCapability 1
service phone ehookenable 1
service phone ehookEnable 1
service dnis overlay
service dnis dir-lookup
service dss
timeouts interdigit 5
system message SwissT.Net
url services http://10.1.10.1/voiceview/common/login.do
url authentication http://10.1.10.1/voiceview/authentication/authenticate.do
cnf-file location flash:
cnf-file perphone
user-locale U4 load CME-locale-de_DE-German-8.1.2.2.tar
network-locale U4
load 521G-524G cp524g-8-1-17
load 525G spa525g-7-5-4
load 501G spa50x-30x-7-5-2b
load 502G spa50x-30x-7-5-2b
load 504G spa50x-30x-7-5-2b
load 508G spa50x-30x-7-5-2b
load 509G spa50x-30x-7-5-2b
load 525G2 spa525g-7-5-4
load 301 spa50x-30x-7-5-2b
load 303 spa50x-30x-7-5-2b
time-zone 23
time-format 24
date-format dd-mm-yy
keepalive 30 auxiliary 4
voicemail 98
max-conferences 8 gain -6
call-forward pattern .T
call-forward system redirecting-expanded
hunt-group logout HLog
moh flash:/media/music-on-hold.au
multicast moh 239.10.16.16 port 2000
web admin system name cisco secret 5 xxx
dn-webedit
time-webedit
transfer-system full-consult dss
transfer-pattern .T
transfer-pattern 0.T
transfer-pattern 6.. blind
secondary-dialtone 0
night-service day Sun 17:00 09:00
night-service day Mon 17:00 09:00
night-service day Tue 17:00 09:00
night-service day Wed 17:00 09:00
night-service day Thu 17:00 09:00
night-service day Fri 17:00 09:00
night-service day Sat 17:00 09:00
fac standard
create cnf-files version-stamp Jan 01 2002 00:00:00
ephone-template 1
url services 1 http://10.1.10.1/voiceview/common/login.do VoiceviewExpress
service phone webAccess 0
softkeys remote-in-use Newcall
softkeys idle Redial Pickup Mobility Newcall Cfwdall Gpickup Dnd Login
softkeys seized Cfwdall Endcall Redial Pickup Gpickup Callback
softkeys connected Hold Endcall Trnsfer Mobility TrnsfVM Confrn Acct Park
button-layout 7931 2
ephone-template 15
url services 1 http://10.1.10.1/voiceview/common/login.do VoiceviewExpress
softkeys remote-in-use Newcall
softkeys idle Redial Newcall Mobility Cfwdall Pickup Gpickup Dnd Login
softkeys seized Cfwdall Endcall Redial Pickup Gpickup Callback
softkeys connected Hold Endcall Mobility Trnsfer TrnsfVM Confrn Acct Park
button-layout 7931 2
ephone-template 16
url services 1 http://10.1.10.1/voiceview/common/login.do VoiceviewExpress
softkeys remote-in-use Newcall
softkeys idle Redial Newcall Mobility Cfwdall Pickup Gpickup Dnd Login
softkeys seized Cfwdall Endcall Redial Pickup Gpickup Callback
softkeys connected Hold Endcall Mobility Trnsfer TrnsfVM Confrn Acct Park
ephone-template 17
url services 1 http://10.1.10.1/voiceview/common/login.do VoiceviewExpress
softkeys remote-in-use CBarge Newcall
softkeys idle Redial Newcall Mobility Cfwdall Pickup Gpickup Dnd Login
softkeys seized Cfwdall Endcall Redial Pickup Gpickup Callback
softkeys connected Hold Endcall Mobility Trnsfer TrnsfVM Confrn Acct Park
ephone-template 18
url services 1 http://10.1.10.1/voiceview/common/login.do VoiceviewExpress
softkeys remote-in-use CBarge Newcall
softkeys idle Redial Newcall Mobility Cfwdall Pickup Gpickup Dnd Login
softkeys seized Cfwdall Endcall Redial Pickup Gpickup Callback
softkeys connected Hold Endcall Mobility Trnsfer TrnsfVM Confrn Acct Park
button-layout 7931 2
ephone-dn 9
number BCD no-reg primary
description MoH
moh out-call ABC
ephone-dn 292
number xxx
description SIP Main Number registration
preference 10
ephone-dn 293 dual-line
number 90 secondary xxx no-reg both
label Zentrale
description 90
name Zentrale
call-forward busy 98
call-forward noan 98 timeout 20
ephone-dn 294 dual-line
number 94 secondary xxx no-reg both
label LL
description Lehrling Lehrnende
name Lehrling Lehrnende
mobility
snr xxx delay 1 timeout 30 cfwd-noan 98
snr ring-stop
call-forward busy 98
call-forward noan 98 timeout 20
ephone-dn 295 dual-line
number 93 secondary xxx no-reg both
label CM
description
name
snr xxx delay 1 timeout 30 cfwd-noan 98
snr ring-stop
call-forward busy 98
call-forward noan 98 timeout 10
ephone-dn 296 dual-line
number 92 secondary xxx no-reg both
label EE
description
name
mobility
call-forward busy 98
call-forward noan 98 timeout 20
ephone-dn 297 dual-line
number 91 secondary xxx no-reg both
label RS
description
name
mobility
snr xxx delay 1 timeout 30 cfwd-noan 98
snr ring-stop
call-forward busy 98
call-forward noan 98 timeout 10
ephone-dn 298
number 6.. no-reg primary
description ***CCA XFER TO VM EXTENSION***
call-forward all 98
ephone-dn 299
number A801.. no-reg primary
mwi off
ephone-dn 300
number A800.. no-reg primary
mwi on
ephone 1
device-security-mode none
mac-address A44C.11A0.B648
ephone-template 1
max-calls-per-button 2
username "xxx" password xxx
type 525G2
button 1:296 2:293 3m297 4m295
button 5m294
ephone 2
device-security-mode none
mac-address A44C.11A0.B566
ephone-template 1
max-calls-per-button 2
username "xxx" password xxx
type 525G2
button 1:297 2:293 3m296 4m295
button 5m294
ephone 3
device-security-mode none
mac-address A44C.11A0.B5C4
ephone-template 1
max-calls-per-button 2
username "xxx" password xxx
type 525G2
button 1:295 2:293 3m297 4m296
button 5m294
ephone 4
device-security-mode none
mac-address A44C.11A0.B67A
ephone-template 1
max-calls-per-button 2
username "xxx" password xxx
type 525G2
button 1:294 2:293 3m297 4m296
button 5m295
alias exec cca_voice_mode PBX
alias exec cca_vm_notification schedule from_time=00 to_time=24
alias exec clid-ALL_BRI ;1:0-4;1:0-9;1:0-9;1:1-9
alias exec clid-SIP ;1:1-9;1:1-9;1:1-9
banner login ^CCisco Configuration Assistant. Version: 3.2 (3). Fri Jul 04 13:18:33 CEST 2014^C
line con 0
no modem enable
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
line vty 0 4
transport preferred none
transport input all
line vty 5 100
transport preferred none
transport input all
ntp master
ntp server 91.240.0.5 prefer
enHi Patrick
I am working on this one as well. I have a UC560 with SIP Trunk provider Les.NET.
It was working fine until a few weeks ago when something changed on the provider end and broke it. My hunch it is something to do with the SIP REFER.
http://www.cisco.com/c/en/us/support/docs/voice-unified-communications/unified-communications-manager-express/91535-cme-sip-trunking-config.html
Here is an excerpt from the above page:
Call Transfer
When a call comes in on an SIP trunk to an SCCP Phone or CUE AutoAttendant (AA) and is transferred, the CME by default will send a SIP REFER message to the SP proxy. Most SP Proxy Servers do not support the REFER method. This needs to be configured in order to force the CME to hairpin the call:
Router(config)#voice service voip
Router(conf-voi-serv)#no supplementary-service sip refer
Figure 3 shows the behavior of the CME system with the REFER method disabled. -
Configuring Level3 SIP trunk with Lync 2013
Hi, I ran into some issues trying to configure SIP trunk from Level 3 and I was hoping someone here can help. We have our mediation server collocated with FE and SIP traffic goes from public IP, port 5060 via NAT, to local IP on FE, port 5060.
Level 3 provided us with one signaling IP and two RTP IPs.
I tried multiple trunk configuration settings and I can see that when I'm placing a call from Lync to an outside number I'm getting INVITE from Level 3 signaling IP, the session is established, phone rings, but there is no audio on either side. There's also
a METHOD NOT ALLOWED message coming from them, which doesn't tell me much about what's happening.
If I call to a Level 3 DID (assigned to my Lync user account) there's also INVITE from their side, but later I receive a CANCEL from them due to idle session. The phone never rings.
Questions:
1) Does anyone have Level 3 SIP trunks configured and can share their Get-TrunkConfiguration settings? What settings should I have for encryption, refer, sessionTimer / RTCP, and others? Level 3 refuses to provide any additional information besides IPs.
2) Do I understand this correctly that when configuring PSTN gateways in topology, one of the RTP IPs should be entered in the "alternate media IP" field? We have SIP trunks from another provider (which work fine), and they only use one IP
for everything, so I don't have any experience configuring separate SIP and media IPs with Lync.
Thanks, and let me know if I should provide additional info.Hi,
On Lync topology PSTN gateways interface, please check if you enter gateway listening port 5060 and enable TCP option.
Please also check if you enable refer support on Lync Server Control Panel, if you enable it please uncheck it.
You can compare the trunk configuration for Level 3 in the part “Sample Trunk Configuration for Level 3” in the link below with yours’, it is for Lync server 2010 but similar for Lync server 2013:
http://blogs.technet.com/b/nexthop/archive/2013/04/10/configuring-lync-2010-server-to-work-with-level-3-sip-trunking-services.aspx
Best Regards,
Eason Huang
Eason Huang
TechNet Community Support
Maybe you are looking for
-
Site lost activation out of nowhere - How do I find and enter the activation key through VPN?
I had a message that site comms went down. My clients sent somebody on-site and all is working but the OnPlus agent still shows comms down. I VPN'd in and can get to the web page for the unit but it's asking me to activate it. Is there a way to fi
-
A classpath error while importing a class with @page import property
Hi , I am using Tomcat contaniner for jsp applications. I have developed a page that i have import a class. when i use <%@ page import="myclass" &> i got an error that myclass not found. I have placed into tomcat\webapps\myproject\web-inf\classes dir
-
How do i get albums from the iTunes store that i accidentally deleted from my library
i accidentally deleted all of my albums from the offspring that i bought on iTunes, how do i get them back without having to buy them again?
-
When I opened my Lightroom 3 today, everything was gone. My catalogs, presets and preferences are all GONE. It's as if the program has been reset. Does anyone know why this might have happened?? Any advice is greatly appreciated!
-
Hello, I currently have duplicates of all the recordings in my iTunes. Why is this and how do I get rid of them? thanks