A stumper! Help! 5 Buck to the solution! 2 AP in bridge mode plus Router to internet

Here is my setup. Draw yourself a diagram please
I have a Axis camera video server box model 2401 connected with RJ45 to a Linksys AP WAP54G in the barn.
The barn WAP54G is then wirelessly bridged to another WAP54G in the house . The house WAP54G is in AP mode. The barn WAP54G is in bridge mode. The MAC addresses are entered properly in each. Same channel, No encryption,
The barn WAP54g is 192.168.1.57 static
The house WAP54G is 192.168.1.244 static
The house WAP54G is then RJ45 connected to the master wireless Router LInkysys RTP300
I do not use the phone ports...just as a regular router ..it works fine. The IP is set to 192.168.1.1
The DHCP range of the wireless is from 10 to 40 so it doesnt conclict with the static IPs of the APs
the home computer is a IBM clone. Connected to the master router via RJ45
IP assigned dynamically for now at 192.168.1.15
Master router connected to my cable modem box
So currently i can access the Axis camers server from the home computer/......by typing 192.168.1.57.. I can see the cows in real video eating thier oats. The firmware in the Axis server allows me to zoom and tilt.
All is good
The challenge is this: I want to see the cows from the internet. I have a static Internet roadrunner cable IP internet address = 12.34.56.78
I am trying to port forward the Axis Server to the internet . I have the Axis server set up as port 8009. ( Doesnte seem to matter when viewing internally with home computer what the port is) .
In the master router i have port forewared the AXIS Server ( IP 192.168.1.57 PORT 8009 to 8009, Both modes, Enable)
When i try to access the Axis Server via the internet address 12.34.56.78:8009...replies "cannot connect to the server".
I have tried variuous port numbers,
As a sidebar, I can see another camera i have from the internet. It is a USB still camera attached to the home computer. And port is set to 89. I can see it from the internet as 12.34.56.78:89 .
So i know the router is forwarding properly. it works with the USB camera hooked to the home computer
Help! Any ideas ? I have exhausted all options.............5 bucks to the winner!
thanks
appleo
Solved!
Go to Solution.

Well I figgured it out myself late last night
I made some changes to the AXIS server...and to the LInksys router
changed DNS server on axis to match the IP of the router was 255.255.255.0 now 192.168.1.1
changed the port forward entry on the router to TCP only
not sure which fixed it but it woks on internet
BTW once i port forward to the internet, the axis server cannot be seen on internal IP
thanks to those who responded..i wil bookmark those links in case i need for future use
appleo

Similar Messages

PLEASE HELP ME TO FIND THE SOLUTION REGARDING "LOGICAL SYSTEM CHANGED"

HAI EVERYBODY,
PLEASE HELP ME TO FIND THE SOLUTION REGARDING "LOGICAL SYSTEM CHANGED" during the material master replication by using middleware parameters.
step1 : i have taken SRM client 810 and named it as CHINNISRM
step2 : i have taken r3 client 810 and named it as CHINNIR3
step3: During material master replication i maintained tables like crmconsum,crmrfcpar,crmparoltp in r3 and smofparsfa in srm client and filtered the objects and loaded the objects through r3ac3,r3ac1,r3as.
step4 : And later i have checked in r3 queues to activate the objects,but i have seen a message like "LOGICAL SYSTEM CHANGED:SEE 588701".according to the oss instructions i have checked in CRMPRLS table in se16 in R3 .there i found out there is one logical client named with T90CLNT810.
oss :588701
Solution
There are different cases in which different forms of processing are
required or where several options exist:
- The logical system name of an R/3 Backend client was changed in
current operation. In this case, the data hangs in the outbound
queues of the R/3 Backend system as specified under point 1 of
the symptom. In this case, the logical system name must be
changed back to the original value. Then the outbound queues
can be reactivated. If no data was transferred to the EBP/CRM
server before the change, also a correctioin of the check table
is possible.
- The same logical system name was used again in a new client of
an R/3 Backend system that was linked to the EBP/CRM server. In
this case, the data is in the inbound queue of the EBP/CRM
server with the exception GUID_FOR_LOGSYS_CHANGED. In this
case, the queue entries which have status SYSFAIL must be rejected, however, not the entire queues. If the new client of the R/3 Backend system you have linked has exactly the same
data as the old client and if it is meant to replace the old
client (that is, this was deactivated), also a correction of
the check tables is possible. In this case, the inbound queues
can be reactivated after the correction.
oss:765018
1. If the situation in your system corresponds to the situation described
under "Reason and Prerequisites" and if symptom 1 occurs, you can
delete the table entry from table CRMPRLS table (there is just one
entry). Since there is no maintenance dialog for this table and you
cannot maintain it using transaction SE16, you must use a report to
delete it. This report is attached to this note as correction
instructions.
Create the report ZZ_DELETE_CRMPRLS in your system and copy the source
code from the correction instructions. You cannot implement this
source code using transaction SNOTE.
You can use the report in every plug-in or plug-in basis system, even
if it is not specified in the validity section.
After you have run the report, you can trigger existing queues again
in transaction SMQ1.
2. If the situation in your system corresponds to the situation described
under "Reason and prerequisite" and if symptom 2 occurs, you can
delete the entry from table CRMMLSGUID (there is just one entry).
Since there is no maintenance entry for this table and you cannot
maintain it using transaction SE16, you must use a report to delete
it. This report is attached to this note as correction instructions.
If they do not yet exist, add the following messages to message class SMOF in your logon language:
Message Message short text
303 User &1 is not allowed to change table &2.
304 User &1 IS not allowed to display table &2.
305 Logical system &1 was not found in table &2.
306 System error! The current client was not
found in table T000.
Create the report ZZ_DELETE_CRMMLSGUID in your system and copy the
source code from the correction instructions. You cannot implement
this source code using transaction SNOTE.
You can use the report for every release of the CRM system, even if it
is not specified in the validity section. The only exceptions are CRM
releases with Support Package versions that are too low such as CRM
Release 3.0 with Support Package 12.
After you have run the report, you can trigger existing queues again
in transaction SMQ1 of the R/3 back-end system or transaction SMQ2 of
the CRM system.
so what should i do to do the replication.please suggest me .untill and unless i solve my problem i cant move to the further activity.i hope you people can solve my problem.thanks in advance.
thanks and best regards,
n.chakradhar

Hi chakradhar,
Did you find a solution to your issue? We are facing a similar issue and looking to figure out how this can be resolved.
BR// 420

Yosemite made my MacBook Pro so slow !! Need help ? what is the solution?

Yosemite made my MacBook Pro so slow !! Need help ? what is the solution?

I've ran a benchmark on my Mac (iMac early 2009). Performance of Yosemite in general was about the same as Mavericks. But that can be different on other Mac's of course. Safari is mostly a bit slower. It's recommended you clean your old internet-caches and then restart Safari. (you can use a little app called CCleaner to do that). That might make a difference. Speed-issues are usually solved in the first and second update of OS X.

TS1559 nothing works with fixing my bluetooth on iphone 4. i cant sinc with my kia optima via bluetooth can anyone help me. none of the solutions that apple lists in their resolution section works.

My bluetooth on my iphone does not sinc with my kia optima. Can anyone help with this? No solution listed by apple in their resolution section works with my phone.

So what's the symptom you're seeing? Can you go to Settings > General > Bluetooth and turn bluetooth on?
Can you go to your Kia and turn its bluetooth on and have it discover nearby devices?

Using the 1262 AP in Workgroup Bridge Mode

Client has a building that is located 300Ft apart and would like to provide IP communications for 3-4 IP hadsets back to an IP PBX. They do not want to dig up the parking lot so we proposed using a wireless bridge. I noticed that Cisco discontinue the 1300 and 1400 Wireless Bridge. Can I use a 1262 with external antenna in Workgroup Bridge mode to perfom this functions? I will put a Layer 3 switch on both ends to route traffice (3560C-8). Should I use the Yagi antenna's for outdoor use? Thanks!

You could go WGB, but root/non-root might work better. This will allows you to pass multiple VLAN across the link.
This is a bit old, but it' the Bridge Range utility
http://www.cisco.com/en/US/prod/collateral/wireless/ps5678/ps458/prod_technical_reference09186a00800a912a.xls
HTH,
Steve
Please remember to rate useful posts, and mark questions as answered

Please help me in finding the solution for this query

Hi Experts,
How could i print column name's second word in next line
suppose am taking ename alias as "employee name"
i want to print the second word "name" in next line
like
"Employee
Name"
Whats the way of writing this query
Please help me out
Thanks in Advance

Hi,
914618 wrote:
WITH mydata AS
SELECT 1 emp_id, 'John Smith' emp_name FROM DUAL UNION ALL
SELECT 2 emp_id, 'Steve Jobs' emp_name FROM DUAL UNION ALL
SELECT 3 emp_id, 'Larry Allison' emp_name FROM DUAL
SELECT emp_id, emp_name
FROM mydata;
after executing the above query the o/p I am getting is in the normal format like EMP_ID and EMP_NAME
not according to my requirement like
Emp Emp
Id NameWhat are the results you reaally want? Do you want this?
`   EMP_ID SPLIT_NAME
         1 John
           Smith
         2 Steve
           Jobs
         3 Larry
           AllisonIf so:
SELECT emp_id
,      REPLACE (emp_name, ' ', CHR (10))     AS split_name
FROM      mydata
;The results above are 3 rows, not 6.
What results would you want if emp_name contained 3 or more words? For example, if you add this to the sample data:
SELECT 9 emp_id, 'Aung San Suu Kyi' emp_name FROM DUAL UNION ALL

Hi, I have a requirement below. It would be appreciate if you would help me out with the solution

I have ACCOUNT_OPENED_DATE assume it is between 04/01/2013 and 04/30/2013 and also I have measure no.of Products
I want to know the status of the No.of products in May, June and JUly for the accounts opened in April means 1 month after, 2 month after and 3 month after
Hope you understand the requirement.
Thanks and Regards,
Chandu

Chandu,
You have written body in subject from next time make subject header more clear
coming to your problem pull month column , no.of.products to criteria it automatically groups data by Month
or
create separate measures/columns for each month using FILTER function : filter (no.of.products using (mnth_name='May'))
thanks,
Saichand

My iPhone isn't working ringtone while a call incoming pls help to give me the solution

My phone isn't ringing sound while I got call from incoming

try going into settings,click sounds,click on ringtone,pick a ringtone,turn up the slider below ringer and alerts,see if that helps

Can anyone help me to get the solution - error mentioned in the description

16:11:40,907 ERROR [ArtistFormHandler]
CAUGHT AT:
CONTAINER:atg.repository.RepositoryException; SOURCE:java.sql.SQLIntegrityConstraintViolationException: ORA-02292: integrity constraint (ATGPROD.SYS_C007131) violated - child record found
       at atg.adapter.gsa.GSAItemDescriptor.removeItem(GSAItemDescriptor.java:7310)
        at atg.adapter.gsa.GSARepository.removeItem(GSARepository.java:1096)
        at atg.repository.servlet.RepositoryFormHandler.deleteItem(RepositoryFormHandler.java:1873)
Caused by: java.sql.SQLIntegrityConstraintViolationException: ORA-02292: integrity constraint (ATGPROD.SYS_C007131) violated - child record foun
        at oracle.jdbc.driver.T4CTTIoer.processError(T4CTTIoer.java:445)
        at oracle.jdbc.driver.T4CTTIoer.processError(T4CTTIoer.java:396)
       ........65 more
SOURCE EXCEPTION:
java.sql.SQLIntegrityConstraintViolationException: ORA-02292: integrity constraint (ATGPROD.SYS_C007131) violated - child record found
       at oracle.jdbc.driver.T4CTTIoer.processError(T4CTTIoer.java:445)
        at oracle.jdbc.driver.T4CTTIoer.processError(T4CTTIoer.java:396)
        at oracle.jdbc.driver.T4C8Oall.processError(T4C8Oall.java:879)
        at oracle.jdbc.driver.T4CTTIfun.receive(T4CTTIfun.java:450)

This is an exception thrown by your DB, you are trying to delete an item that is referenced somewhere else. Check what is the definition of 'SYS_C007131' constraint and you will get to know which table it is referring. You need to set cascade="delete" in your repository definition to delete all child records as well.
You can find some details here :- Oracle ATG Web Commerce - Cascade Delete
Cheers
R

I have iphone 4 ios 6.1.3. My wifi disconnects everytime i lock my phone. Please help if you know the solution

Please help

But still its a disadvantage. Suppose my phone is in sleep mode and i get a chat message or some email. I wont get it at that moment, but after turning on my wifi manually, i'll receive the message. Dont you think its irritating?

Extending airtunes on the cheap? Can I bridge A.Express w/ Share Internet?

My father-in-law wants to know if he can plug the router straight into his new iMac, setup share internet in system prefs, and then use the airport express to extend the coverage area just like you would if you had an airport extreme and and express.
Links and tutorials are appreciated. Thanks!

This should work... I'm
1. Connect the modem to the iMac
2. Under System Preferences, go to Sharing
3. Check "Internet Sharing"
4. Select Share your internet connection from Ethernet
This is where the water gets murky since I'm on this forum with an Airport Express that's been acting up...
5. Plug your Airport Express (AE) to where you want it, make sure its in the factory default state (you can look at up if you don't know how)
6. Connect to it via wifi from your iMac (while its still connected via ethernet cable to your cable modem)
7. Proceed to set it up with Airport Utility
8. Follow directions to set it up as a network extender (you can also look around for that on Apple's Support website)

The mutilple ssid configured on bridge mode access point

Is it possible to configure mutilple ssid under one dot11 interface when the AP works on bridge mode

Hi,
This is Linksys Community Forums and not HP Community Forums. You may want to create a post on HP Forums instead?
If everyone needs to believe in something, I believe I'll have another beer..

How the solution manager is realated to SAP BW

Hi experts!
Well!! I have been given a task to work on solution manager 4.0 and make it useful for SAP BI.
so I have a few questions.
1) Does basis person look after the config and authorizations?
2) I have been told to include the system change request ( SCR), Help desk issues into the solution manager... so how can I get that.
3) where my role starts exactly, I mean after connecting SAP BI to Solution manager,I guess this is done by BASIS person.
Points will be rewarded to the helpful replies... thanks in advance.

Hi Abass,
To answer few of ur questions,
2) you need to configure the Solution manager tool with the BI system when a ticket is raised or a change is triggered. These things will be monitored by a help desk or service desk person or a BI expersie person.
I guess your role is to implement this in ur org that means you need to create from basics such as creating business partners etc
Regards
Srini

Using Extreme in Bridge mode, can't see the DHCP clients if the D-Link router

I have an Airport Extreme attached to my DLink modem/router. I have configured the Airport Extreme in Bridge mode, and I was expecting all clients to show up in my D-Link router. Although the configuration works most of the time, I have been experience a few issues:
1. From time to time, computers attached (both Windows and/or Mac) complain about an IP address conflict. I can ignore the error and it works fine.
2. From time to time, I loose Internet connectivity, and I need to disconnect my computer and reconnect again to solve the issue. This is not necessarily linked to symptom #1
3. On my D-Link router/modem (which I only use to connect my Airport to my ISP), if I check the DHCP clients, I can see the Airport router connected and *some* of the wireless clients that connect through the Airport. The list changes quite randomly, and at times, I see the airport appearing twice with different IP addresses.
Any help configuring it "right" will be appreciated!
Alain

When the AirPort Extreme is in bridge mode, the AirPort Extreme is simply passing through the DHCP settings and services that are handled by the D-Link modem/router.
In other words, the D-Link device is in total charge of the DHCP services for devices on the network.
You might want to check with D-Link support to see if they have any recommended practices for configuing the modem/router when another router....the AirPort Extreme in this case....is being used in bridge mode on the network

I have FIOS and the latest version of the Airport Extreme Basestation set up in bridge mode.

OK need some technical answers I have FIOS and am forced to use their Router. I have WiFi turned off on the FIOS router and my New version Airport Exteme Basestation set up in Bridge Mode. I have CAD 5 running to all my Mac computers and a CAD 5 up to the second floor. I have an older version Airport Extreme Basestation that I would like to connect to the CAD 5 cable on the second floor where the WiFi signal is weak as the main Airport is in the basement. How would I connect the second Airport to the Airport that is in Bridge Mode? Will this setup mess up my signal strength on either CAD 5 or WiFi? I will also have one Macbook Pro plugged into the upstairs Airport. This is mainly for the WiFi for my iPad and iPhone. Details will help. Thanks.

How would I connect the second Airport to the Airport that is in Bridge Mode?
Connect from a LAN <-> port on the Bridge Mode AirPort to the WAN "O" port on the second floor AirPort and then use AirPort Utility on a Mac or iPad to set things up.
Will this setup mess up my signal strength on either CAD 5 or WiFi?
Nothing will be messed up, and you will have a much stronger WiFi signal upstairs.
If you need more details on setup.....we need to know.....
1) What model number of AirPort Extreme will be upstairs. The model number is usually embedded in the foam base on the bottom of the device. Starts with an "A" followed by four numbers. Example.....A1143.
2) What operating system you are using on your Mac, or whether you want to use the iPad for the setup...assuming that the upstairs AirPort is compatible.

A stumper! Help! 5 Buck to the solution! 2 AP in bridge mode plus Router to internet

Similar Messages

Maybe you are looking for