A1083

any place to buy these anymore?
always meant to buy one, but got busy.
Reasons:
don't want to replace my dual dvi video card.
want the matte.
30" is better than 27"
two monitors workflow doesn't allow direct focus.
need monitor to work for leopard and lion.
don't want to mess with an adaptor.

Do your own research. This is not your personal shopping assistant.

Similar Messages

  • HT2810 No power - Apple Cinema HD 30 (A1083)

    Hello, I have a Apple cinema HD 30 (A1083). I have no power. I checked the power supply and it is good. I bought a main board from ebay. I still had the same problem so I returned it (minus a 15% restocking fee). I read somewhere that you have to have the usb cables plugged into the computer for it to work. Is this true? If so I may have returned the part I needed to make this monitor work. (just my luck) I bought this monitor for $25 used off craigslist. I am really excited to get this working. I have heard great things about how fantastic the dispay is. I am ready to do some gaming on it. I am an electronic technician but not so familar with this apple monitor.  I figured I would turn to this forum to learn from some apple experts out there. Any imput would be wonderful in troubleshooting my problem.
    thanks
    Tommy

    The display should work with no USB connection.  USB is needed for computer control of brightness, and for the USB ports on the back of the display, but is not needed for the basic display operation.

  • Hi, I have a Apple A1083 Cinema Hd Display 30" Widescreen with a broken lcd, where can I get the replacement part ?

    Hi, I have a Apple A1083 Cinema Hd Display 30" Widescreen with a broken lcd, where can I get the replacement part ?

    Hi, I have a Apple A1083 Cinema Hd Display 30" Widescreen with a broken lcd, where can I get the replacement part ?

  • Apple 30 inch LCD : A1083

    The bottom half of the display is much darker than the top half.

    This is the iPad discussion board. You're probably better off asking your question here:
    https://discussions.apple.com/community/peripherals/cinema_displays

  • TS3477 How do I connect my HD Cinema display unto my new MacMini?

    I just purchased a new  Mac mini but want to continue using my HD Cinema display. My HDMI connector does not fit into my new Mini. Can I find hardware so I can connect to my new Mac mini?

    Which disply?
    http://en.wikipedia.org/wiki/Apple_Cinema_Display
    The M8563 uses an ADC connector and you need one of these
    http://www.amazon.com/Apple-DVI-ADC-Display-Adapter/dp/B00011KHT2
    If A1082 or A1083 you may need a duela link adopter
    http://store.apple.com/us/product/MB571Z/A/mini-displayport-to-dual-link-dvi-ada pter

  • MONITOR compatibility, MONITOR compatibility

    Does anyone know if a Samsung 320MXN-2 32in LCD Monitor is compatible with a PowerMac G5 to use to edit on FCE? Thank you for any help! Susan

    if a Samsung 320MXN-2 32in LCD Monitor is compatible with a PowerMac G5 to use to edit on FCE?   (Nvidia GeForce 7800GT - 256MB  Dual DVI graphic card)
    Yes, because it has a DVI input and your graphics card has a DVI output.
    Here are the full specs.  But this monitor only has 1366 x 768 resolution and has been discontinued.  It's going for $600-$700 refurbished, $900-$1000 used and if you can find a new one it will be $1200 or more.
    I would think your money would be better spent on a used Apple A1083 30" Cinema Display (2560 x 1600 resolution, will use the dual-DVI output of your nVidia card) or a new Dell UltraSharp monitor (U2711 @ $999, 2560 x 1440 resolution or U3011 @ $1299, 2560 x 1600 resolution)

  • Cinema display 30" power plug caught on fire

    Hi everyone,
    I have a 30" Apple Cinema display (A1083) purchased in 2008. Recently, it's power cable/wire came slightly unplugged from the 150w power supply while the monitor was on. The wire was still plugged in, but it was at a fairly severe angle. Spontaneously, sparks flew between the power supply and power cable/wire and fire shot out of the power supply melting the plastic around the cable. Needless to say but the monitor went dead at that moment.
    I had another power supply laying around so I plugged that in to see if the power cable/wire would still work. The monitor came on for a while but then more sparks and the monitor went dead.
    Apple no longer makes this monitor and apple care is expired (of course). Therefore, I figured I would fix this myself. By some miracle I found the entire set of cables on eBay and purchased them.
    My question is:
    Should I replace the entire set of cables, which would involve opening up the monitor? Or, should I just replace the power cable/wire at the end which would involve some soldering, etc.
    Also, are there any tips, directions, pointers that anyone has for doing any of this? I found one guy online who opened up the case but that is a risky move.http://www.eliteweblabs.com/recent/cinema-display-cable-fix/
    I'm upset my beautiful monitor isn't working and really need some help getting it back, if possible. What do you guys think?
    -B

    Amazon 1
    Amazon 2
    Amazon 3
    Shinza
    TechRestore

Maybe you are looking for

  • Planning strategy 50

    Dear all, I am using strategy 50 for my FG. I have created PIR for FG for 300 qty & created saleorder of 320 qty for FG. while doing availability check for sale order it is confirming only 300 qty bcoz PIR exists for only 300 qty. after this i saved

  • Items and Pages completely disappear, version CC

    Document has items and pages that randomly disappear. I get them back most of the time by clicking on another page then going back to the page that disappeared. I have 12gb internal memory so rendering isn't an issue I don't think? I even took the ti

  • ORAPWD

    hi a question about ORAPWD.....we create password file using oradim command while creating a database.. then what is the need for ORAPWD.....because when we create password file we don tell it any database this file should belong.... and second thing

  • Monitor a web server using java

    Hi All, How can we monitor the webserver and its performance using java? what are the steps we should follow to do it and which java package i should concentrate to do this task?Give me some ideas about this? regards, Maheshwaran Devaraj

  • Maintainence View not displaying contents

    I have 2 custom tables one is zemployee and other is zdept. The foreign key is Dept No. I went to SE11 and created Maintaince View and done all the necessary steps like Relationships and View Fields. Finally I activated my view. Now when I click on C