A1330n front panel connections - mic, headphones, speaker

I have a hp1330n desktop computer
I am updating the motherboard to an ASUS p8H61-M LX plus
The front panel connections for start, reset, hd activity, etc. all work fine when plugged into the 10-1 connector on the asus motherboard
I am trying to figure out if / how I can connect the front panel 4 pin connector for the mic, headphone, speaker that use to be plugged into the 1AUX_IN1 connector on the old motherboard that shipped originally with the a1330n.
There is a 4 pin speaker out connection available on the asus motherboard - +5V, GND, GND, Speaker out, but not sure if I can connect the 4 pin wire coming from the front panel - white, blue, green, red wires (with some modifications) into these available 4 pins.
Or do I just forego this functionality after the upgrade and leave the plug dangling in the case?

I found this, I guess it is compatible with the azalia connections: http://forum.thermaltake.com/files/audioconnector_307.jpg
But I have one more question... looking at the end of the card, which pin is pin ? top left?

Similar Messages

Front panel connections

.I am building a new system but the front panel connections in thr mobo manual need clarification for me .
Front panel connections jfp1 & jfp2
jfp2 -- 4pin speaker wire 2-8
3pin power led 1-5
jfp1-- 2pin hdd led 1-3
2pin reset sw 5-7
2pin power sw 6-8
In the manual it has a 2pin power led 2-4 but there is no wire do I take it that you do not need this .
USB 2 & USB 3
4 pin connector vcc , usb- , usb+, gnd 2-8 or 1-7
this cable has an extra gnd wire I would imagine you just leave this unconnected as there is no 9pin & 10 is usboc .
Front audio
pins 5-6 & 9-10 not to be used .
So that leaves me with 5 connections but manual does not say where they connect .
ear left
ear right
mic vcc
mic in
grd
Hope I have explaine myself ok but woulsd rather be suree before I go any further , I have the rest of the pc in place .
Regards Ian

Found these on an other site much more explicit than manual . There was connection diagram on manual but no direction as to + or - so would imagine 1for example is hd led p for positive .
PIN SIGNAL DESCRIPTION
1 HD_LED_P Hard disk LED pull-up
2 FP PWR/SLP MSG LED pull-up
3 HD_LED_N Hard disk active LED
4 FP PWR/SLP MSG LED pull-up
5 RST_SW_N Reset Switch low reference pull-down to GND
6 PWR_SW_P Power Switch high reference pull-up
7 RST_SW_P Reset Switch high reference pull-up
8 PWR_SW_N Power Switch low reference pull-down to GND
9 RSVD_DNU Reserved. Do not use.
JFP1 Pin Definition
PIN SIGNAL PIN SIGNAL
1 GND 2 SPK-
3 SLED 4 BUZ+
5 PLED 6 BUZ-
7 NC 8 SPK+
JFP2 Pin Definition
PIN SIGNAL DESCRIPTION
1 AUD_MIC Front panel microphone input signal
2 AUD_GND Ground used by analog audio circuits
3 AUD_MIC_BIAS Microphone power
4 AUD_VCC Filtered +5V used by analog audio circuits
5 AUD_FPOUT_R Right channel audio signal to front panel JUMPERED
6 AUD_RET_R Right channel audio signal return from front panel JUMPERED
7 HP_ON Reserved for future use to control headphone amplifier
8 KEY No pin NO PIN
9 AUD_FPOUT_L Left channel audio signal to front panel JUMPERED
10 AUD_RET_L Left channel audio signal return from front panel JUMPERED
So I have 5 wires left
ear right ?
ear left ?
mic vcc pin4 ?
mic in pin1 ?
grd pin2 ?
Sorry if I am dragging this out but waiting on graph card to come so just making sure everything is ok as you guys do a great service .
Ian

K450 motherboard front panel connection

Hi
I need to know the layout for the front panel connection on CIB85M. Searched all around and the closest i got was this, but i dont understand the language:
Link to image
Moderator note: large image(s) converted to link(s): About Posting Pictures In The Forums

Please, I too am looking for this information: pinout diagrams and or wire coloring/descriptions for the Front Panel, Front USB3.0 and Front Audio headers which all appear to be non-standard. Also, there was a Sensor Header that it would be nice to know the layout for just in case I can find a place on the new mobo for it. Our CIB85M is fried so trying to connect everything to a new MSI mobo. Any assistance would be appreciated. Thanks!

No front panel audio or mic when hooked up through xtremegamer

> I have my HAF 922 front panel hooked up to my xtremegamer with the intel HD audio 2x5pin connector. It doesn't recognize any headphones or mic i plug in and doesn't play audio through anything. I've double checked the connection on the card and have disabled onboard sound in the bios. Is there some setting im missing?
Thanks in advance,
Keith

bump

Cannot connect my mic+headphones to the sound card.any he

I can connect the mic wire to the sound card(creative sound blaster audigy 5.)?but i dont have another exit for my headphones wire, so i can talk but i cant hear anything in the headphones - the sound is coming only from the speakers.is there anyway do make the sound go bothways, to the headphones and to the speakers?i tried to connect the headphones to the motherboard soundcard but it didnt have much use....And are there any extension cables so i can extend my headphone wire and connect it to the speaker headphone exit's?Thanks for your attention people.Looking forward to your replies.

xeckuc,
Maybe you can try to get a stereo splitter adaptor to share the audio output with your speaker.
Jason

Audio front panel connection to 10pin Audigy 2 ZS card head

This can't be rocket science. Various manufacturers (e.g. HP and DELL) produce an OEM cable which connects the 0pin card header on Audigy ZS sound cards with their front panel MIC and PHONES jacks.
There have been discussions on various sites for a while on this topic, but they all experience problems (e.g. http://audigy2zshowto.blogspot.com/ ).
The one thing that the OEM cables have in common is that the manufacturers' front panels adhere to the AC'97 front panel format (e.g. http://www.formfactors.org/developer%5Cspecs%5CA2928604.pdf and http://www.alsa-project.org/alsa/ftp/datasheets/intel/30234902_ICH6.pdf ). They don't appear to be using the Intel High Definition Audio alternati've to AC'97.
So, it should be very simple to map each of the 0 pins (on the x0 header) on the Audigy sound card to each of the 0 pins (on the 2x5 header) that the AC'97 standard specifies (and which HP and DELL use). OK, I know that pin 8 on the 2x5 is a "peg" and so there may be some redundancy on the x0 connector, but there should be a robust mapping that enables the muting functions to work properly and for there to be decent microphone performance.
So, what is the mapping? Someone from DELL, HP and Creative must know. (Let's make it simple as well, let's answer this like "when connecting the x0 to the 2x5 then pin maps to pin x, pin 2 to pin y, pin 3 to pin z and so on".)
Once I get some answers I'll also provide a full parts and tools list for people wanting to make cables of their own.

Hi Avi,
The Audigy 2 dri've should be compatible with an Audigy 2 ZS card, so yes.
Cat

Audigy 2 Platinum Front Panel Connecti

I recently began recording my band in our home studio. My mixing board is a Midas Venice 240 which has two balanced XLR outputs from the master bus. I am wondering what method I may use to connect this output to the /4" stereo input on the front panel of the Audigy 2 Platinum. If I just purchase a Y-adapter to combine the two channels into one XLR and then convert it to /4" TRS jack will both channels be preserved? Are there any sound quality issues that arise from this method of connection? I was hoping to get answers to these questions before wasting money buying unnecessary adapters.
Thanks

The BEST way to do this is to go to radio shack and buy two (yes 2) of their?XLR to /4" Impedence Matching Transformers, AND?one (yes )?dual /4" female TS (tip-sleeve) to single /4" male TRS (tip-ring-sleeve) "Y" cable. Unless your mixer also has /4" main outs as well as the XLR... then you can just use the Y cable and skip the transformers. Or you can use a /8" Y cable with the transformers (and stereo /4 to stereo /8 adapter) and go into the card's line in jack on the actual card. Which is how I did it for a year or more untill i got a firewire recording interface (and it worked darn good too with my Soundcraft mixer and some good microphones). Either way,?you need the transformers for optimal results. The reason is the mixer's output impedence and level doesnt match that of the soundcard's input... mixer will likely overdri've the card, or the signal will sound weak or noisy.. The transformers?are cheap and are darn handy for loads of recording functions, and will provide the Audigy with exactly the type of signal it needs, properly transformed from the mixer. If you do this, you can record ALL of the mixer channels IN STEREO with all the panning, effects, and levels preserved. If you have multitracking software like Cubase or similar, you can even record an individual instrument (or even 2 at once, one panned left, one right... each assigned its own track in your software), come back on a new track (or pair of tracks), and record a different instrumet (or 2) and build a multitrack recording one performance at a time. PS:? you CANNOT just hardwire the mixer outputs and combine them into a single channel. A mixer is needed to properly combine?signals. Don't do it
!!! Have fun... and rock on.PSS:? make sure your overall cable is as short as possible. If you must run it for more than 6 feet then run it in XLR mode and convert it very close to the computer. The non XLR section of cable is an antenna for noise. The XLR section will be shielded against noise. Also, the transformers are kinda heavy so do not plug them into somthing and allow them to hang in the plug becasue the hanging weight will ruin your jack. Its best to run cables to the transformers, allowing them to lay on the floor... in a safe place where they wont get stomped on.
Message Edited by ElectricUrinal on -28-200708:0 AM

Remote front panel connection

I want to view a labview front panel from a remote PC. But I only have one computer at the moment. So I am trying to simulate this at local computer by setting the server address as localhost. But the connection is refused and it says: connection to a local labview application is not allowed.
Is that a part of labview feature or caused by improper setting in labview?
What should I do at this point?
Thanks for your reply.

It is a LabVIEW feature. Remote front panels are meant to be used on two separate machines. If you want to set something similar from one computer only, you can try the web publishing tool that embeds the VI in a htm page that can be viewed by using any web browser either on the same/ remote machine.
Regards,
Ankita

SB Live Front Panel connect

I am upgrading to a new computer case. The Li've card (sb0200) has a 0 pin
single row connector for the front panel of the Dell case. The new case
Antec Nine Hundred has a 0 pin double row connector as well as 7 single
pin connectors. Is there an adaptor that will allow the 0 pin double
row connector to be connected to the 0 pin single row connector on the
Li've card? Or is there an adaptor that will allow the 7 single pins to
be connected to the connector on the Li've card? What can I do? thanks!

Here's a thread with information on that topic:
http://forums.creative.com/creativel....id=3949#M3949
-Dave
?[email protected]

Front panel connection/ Sound Blaster Live Va

Does anybody know if you can hook a Li've Value to front panel connectors. I checked the user manual and there isn't much information on pin assignments.

up...

MSI P67A-GD65 - Front panel connections and sli A NO GO!

I have issues with this board and two gtx580 cards in sli, because If I plug the front panel connectors (power, reset, power led, hdd), the bottom card won't fit.
The issue was already found here too: http://hardforum.com/showpost.php?p=1036689234&postcount=81
Any solution from MSI.

That's not a problem for me; as the cables are plenty long. In regards to cable length the position is actually reasonable (though higher up on the same edge would address both issues). I've used at least one mb that had the connector about as far away as possible from the front connectors (it wasn't an msi - the last msi board I used was a K-3 which was really nice; still use it in my Dad's computer). Oh well I hope MSI respond to my ticket; as well as the other fellow; if nothing else maybe in the future they will address the issue.
Quote from: Bernhard on 21-March-11, 04:52:00
The MSI design alone is not the only problem. The case designers also leave the geader cables shorter than desired. I have no problem with my CM 690, but the other cases just seem to have cables that are about 10cm too short.
One solution I have employed is to route those cables under the board, diagonally, as the cable thickness is just less than the standoff heights. Thus, lay the cable in the case before inserting the MB. That way at least they won't get in the way of the GPU cards.

Can Audigy 2 Platinum front panel connect to X-fi?

Hi,
I'm about to build a new i7?system and am debating buying an X-Fi Titanium (non-fatality)?to replace my Audigy 2 Platinum. Is it possible to connect the front dri've bay from the platinum to the X-Fi card? If not, I'm wondering if it is worth the switch. I'm not keen on paying any more than the price of the standard titanium card, so am not looking at the pro, etc.
I'd appreciate any thoughts. Thanks!
Message Edited by motility on 05-05-2009 09:44 AM

Oh well, it is already ordered. It is rather absurd in this day and age that Ceati've charges 00 plus dollars premium?for such simple functionaility. Even M-Audio seems to provide better connectivity solutions on its low end interfaces. I have one of those. Guess I can just get an RCA to /4 inch or XLR adaper.
Still looking forward to the X-fi, though,

Front Panel Audio connection help needed

I own an MSI 790GX-G65 with Realtek HD audio, installed in an NZXT Tempest case.
Using the AC-97 plug from the case into the MB JAUD1 connection I get front panel headphone audio, but no mic input or automatic detection from the Realtek manager.
In short: Which plug(s) do I use on the MB socket JAUD1? I will detail my NZXT front panel connections.
NZXT Connectors:
Maxi Plugs:
HD Audio
AC-97
Mini-Plugs:
MIC-IN
Ground
L-Out
Ret-L
Ret-R
R-Out
MIC-VCC
FYI: I'm using Windows 7 64 bit. OS has been updated to current.
Thanks for your help.
Merry Christmas!
Robert

Ok. I checked and confirmed... I DID use HD Audio in JAUD1. I only thought I was using AC97... The problem still is:
Front Panel Headphones: Okay.
Front Panel Mic: Not detected at all.
Audio driver version is 6.0.1.6316
Audio Controller HD Audio
Audio Codec: ALC889
DX11
Window 7
Thanks for any further suggestions

Front panel USB connection to MB 990fxagd80v2

Hi Gents, new member here with some issues on me last build. I assemble my families computers , about one every 5 years. Other than that I am not hot in computers. So when I get into a build I have some homework and studying to do, and some glitches. At this moment my newest machine is up and running Win 7 with a few loss ends. My case is an USB 2.0 era with 2 ports in the front bottom behind a little door. Each USB cable has 3 wires ending in a flat 3 pin female plug. The motherboard has 2 USB male ports, 9 pins each, one coded blue the other red each one has an alignment notch. This MB came with a sack of M-connectors to be an easy transition between the front panel plugs and the Motherboard, so, 2 of the M-connectors are red and blue, and have alignment lugs that appear to be made for the USB ports on the MB. The problem is they do not fit. While I am gentle and careful I don't believe they fit. I have other front panel issues I'll save for another time. My Gazelle case seems to use different nomenclature than the motherboard. But the USBs are the issue now, anyone have some light on this subject? I would also like to convert one of the front USBs to 3.0.

"Each USB cable has 3 wires ending in a flat 3 pin female plug."
That can't be right as USB are 4 wire, red, white, green, black. Connectors are 5 or 10 pin plugs with no connection on the 5th pin not used on both types & 9 being the key on the 10 pin plug.
"I'm not sure is I have a variation from the standard MB or what..."
Any connectors, MB headers are standard throughout the industry therefore they will be the same from all manufacturers.
"or is the connection does not use m-connectors"
You should not need m-connector for USB anyway. m-connector was introduced mainly for front panel connections that had individual wires for each LED, switches and such. The set in the pic I show is from old P35 MB.
Can you post a photo(s) of the case connectors you have?
See here how to add photo's: https://forum-en.msi.com/index.php?topic=90789.0
Personally I use Photobucket to host my pics.
M-connectors for USB should be clearly marked as such if the MB even came with any for USB. Over the years they have eliminated some and I think the ones for USB were eliminated.
USB plug:

Mic In 2 on front panel don't working (but after many read, he don't working agai

Hi people !
So i've a little problem with my Mic In 2 on my front panel I/O. I'd a soundblaster X-Fi Xtrem music, and recently, i've upgrade her with an optional Front Panel I/O. The front panel work perfectly, and two days ago, after reinstate the PC, the MIC IN 2 don't work suddenly. This back MIC IN work perfectly, but no signal for the MIC IN 2 on front panel. I've reinstate the drivers (the last drivers on the creative official site), i activate the MIC, activate the potentiometer at max on front panel, activate the mic boost in windows xp audio panel, i try another entry (ligne IN, auxilary...) for this MIC 2, i check the AUDIO CONSOLE... but the MIC IN 2 entry is not activate.
I read many post, but waht's the Creative Mixer ? I don't have Creative Mixer but Creative Audio Console. If is the even of windows xp Audio panel, the Line 2 (call "Line IN" normally in my pc : yes i've txo "Line IN", one at left (not activate at the same time of microphone) and one at right (activate in the same time of microphone), she's activate...
The MIC IN 2 work, i'm sure, but i've no signal because this entry appear disable for me ( despite Windows Xp Audio Panel ),
Someone have a solution ?
Thanks in adavance
Message Edited by Claymenia on 04-20-2008 0:55 AM

i made work my MIC IN 2 in front panel, with removing jumper (dynamic mic), but i heard my mic but windows xp software (msn, teamspeak, skype...) do not receive a signal. this very strange, with removing jumper, the MIC IN 2 is activated on front panel hardware but no in software (audio panel windows xp).
If i desacti've the LINE IN 2 in audio panel of windows XP, the mic don't working (no hear) but if i desactivate Microphone, he work normally... (but for the two solution, windows xp don't receive any signal)
No idea ?
Message Edited by Claymenia on 04-20-2008 02:28 AM

A1330n front panel connection​s - mic, headphones​, speaker

Similar Messages

Maybe you are looking for

A1330n front panel connections - mic, headphones, speaker