A305-S6825 shutting down by itself

I hope someone can help me with an issue that I am having with my A305-S6825 which I purchased in April/May 2008. In the past two weeks I have had the computer shutdown by itself. The computer shut down twice in a matter of 30 minutes the otherday. There's never any warning. The computer screen goes black and the computer is off. It has always happened when I was watching a video on the Internet.
I was told by techsupport the issue could be virus/malware, a bad hard drive or bad RAM. I have run 3 malware programs...no virus, no malware. I have run SeaTools...all tests. I have run chkdsk...past. I haven't figured out yet how to test the RAM.
99% of the time I run the computer plugged into an electric outlet. While I have a cooling pad under the computer at all times, I have noticed at times of late the cooling fan is screaming.
Also, I have noticed over the past couple of months that watching video from the Internet that video and sound haven't always been in sync and that there seems to be a buffering issue because the feed is very choppy.
Will these shutdowns show up in the Event Viewer? If so, where will I find them?
Are these powers all related?
If it is a cooling/cleaning problem, are the only two places to blow air into the round fan intake on the bottom of the computer and the exhast vents on the side of the computer? If the computer needs to be opened and clean can I do that or do I need to GeekSquad or someone like that to have them clean?
Thanks in advance for your help.

If you have cleaned the cpu cooler and checked for a loose connection between the cpu cooler and the cpu and you are still having a shut down issue,perform the following:
When the computer shuts off, try to turn it back on.
If the computer shuts off again, using a pc vacuum (NOTE: do not allow the vacuum to over rev the cooling fan), try to cool the cooling fins of the cpu cooler by pulling air through the outside cooling vent for approximately 10 to 15 seconds.
Turn the computer back on again.
If the computer stays on longer, it could be a fan issue. Replace the cooling fan.
I completed this procedure about 2 weeks ago and my laptop has not shut down while in use since (other than when I shut it down). apparently the OEM's fan RPMs do not coincide with the motherboard's readings.
Also I no longer use a laptop cooler to keep it running either.
I hope this helps you.
Regards.

Similar Messages

  • After 2 weeks my Iphone 4s shuts down by itself and I cannot  turn it on. What can I do. Itunes is telling me to restore the phone but the phone is saying the software isn't available

    My Iphone 4s  shut down by itself after a phone call and I cannot turn it on. I took it to istore and they said it was unrespinsive and there is nothing they can do? Anyone has a clue what can be done? When I connect the phone to itunes it indicates that the phone should be restored, however when i try to restore it, it says the "software for this iphone is not currently available" Is there anything I can do other than put this brand new iphone in the grabage?

    On computer, at the top of this page is a Tab for iTunes, click it, make sure iTunes is up to date. Also make sure computer Fire Wall and Anti Virus do not interfere with iTunes, turn them OFF to be certain.

  • SAPCCM4X agents are shutting down by itself

    Hello Gurus
    A few SAPCCM4X agents are shutting down by itself and this is happening
    for systems which have a version 4.6c and 4.5B in our landscape like PCX.. Analyzing the log of one of this agents the
    message below is informed:
    Mon May 9 04:41:10 2011
    CCMCTRL: ERROR: csm_show_file: no permission to
    read /usr/sap/PCX/SYS/profile/PCX_G34_zonepcx
    CCMCTRL: ERROR: csm_show_file: Please check sapccmsr.ini
    I tried to find the profile mentioned in the warning but with no
    succes. The cause of the shutdown of the agent is that because the
    correct profile is PCX_DVEBMGS34_zonepcx instead of PCX_G34_zonepcx but
    why it is looking for the wrong one when everything is configured with
    the profile PCX_DVEBMGS34_zonepcx . I also checked sapccmsr.ini but
    found nothing.
    I  can start the agent normally choosing the correct parameter
    (PCX_DVEBMGS34_zonepcx) but sometimes the agent shutdown by itself
    after 3-4 days with the error message above.
    Why the agent search for the wrong profile and where can I change it to
    the right profile ?
    Or is there any other way to resolve it.
    Thanks and Regards
    Ashwini

    Thank you Mani, I will make this test in only one appl server and monitor.
    I will let you know the resul of my tests.
    Regards

  • How do I get my iPad to stop shutting down by itself?

    How do I get my iPad to stop shutting down by itself?

    What do you mean by "shutting down"?
    Have your Reset it? Restored it from your backup? Restored it as a new device?

  • Why my 2009 desktop with OS Maverick keep shutting down by itself

    Why my 2009 desktop using OS Maverick keep shutting down by itself?

    When it shuts down, the screen blanks (more like turns grey, like the color of the background when on the log in screen). It reboots immediately, so at first the problem was presumed to be restarting, not shutting down and powering back on. The computer is usually very warm, and definitely gets hot easily. A test was run determine when the fan would turn on to start cooling the computer by running digits of Pi, and the tester concluded it was too close within the safe temperatures before it would permanently affect the computer. (I believe this was within 5ºF, but I am not 100% sure.) The times when it will turn off and reboot do not seem coorelated with much if anything. It has done this at multiple times, among running varying amounts of programs and for different lengths of time: right after logging into the user, within a minute of after it has turned off and rebooted, within 5 minutes, 10, 30, even 60 minutes of turning off and rebooting, when only running one program such as Firefox, when running various programs such as Firefox, iTunes, Microsoft Word, Sticky Notes....
    Basically, it makes no sense.

  • I have a 2007 macbook that is stuck on the loading page and after a while it shuts down by itself. I don't know what to do anymore please help!!!

    I have a 2007 macbook that is stuck on the loading page and after a while it shuts down by itself. I don't know what to do anymore please help!!!

    Hello Sebas4224
    Start with the article below to troubleshoot issues with your MacBook starting up and staying on. Let me know how it goes in case it does not help and I or others can assist you further.
    Mac OS X: Gray screen appears during startup
    http://support.apple.com/kb/TS2570
    Regards,
    -Norm G.

  • Emctl shutting down by itself after a while

    I just got 10.1.0.3 installed and a 9i database converted. I can get the Database Control started (emctl start dbconsole) and use it, however, after a while emctl shuts down by itself. Below is what occurs in emagent.trc just before emctl shuts itself down - apparantly gracefully. All help appreciated
    Kirk
    2005-02-11 16:18:05 Thread-1827 ERROR http: 11: snmehl_read: error on read: A connection with a remote socket was reset by that socket. (error = 73)
    2005-02-11 16:18:05 Thread-1827 ERROR upload: FxferSend: HTTP Error=-1 reading request response from: http://serverxxx.university.edu:5500/em/upload/
    2005-02-11 16:18:05 Thread-1827 ERROR upload: Failed to upload file B0000197.xml, ret = -2
    2005-02-11 16:18:05 Thread-1702 ERROR http: 15: snmehl_read: error on read: A connection with a remote socket was reset by that socket. (error = 73)
    2005-02-11 16:18:05 Thread-1702 ERROR pingManager: nmepm_pingReposURL: Error in request response. code = 400. text =
    2005-02-11 16:18:05 Thread-1827 WARN http: snmehl_connect: connect failed to (serverxxx.university.edu:5500): A remote host refused an attempted connect operation. (error = 79)
    2005-02-11 16:18:05 Thread-1827 ERROR upload: FxferSend: Cannot connect to: http://serverxxx.university.edu:5500/em/upload/. retStatus=-32
    2005-02-11 16:18:05 Thread-1827 ERROR upload: Failed to upload file B0000197.xml, ret = -2
    2005-02-11 16:18:05 Thread-1702 WARN http: snmehl_connect: connect failed to (serverxxx.university.edu:5500): A remote host refused an attempted connect operation. (error = 79)
    2005-02-11 16:18:05 Thread-1702 ERROR pingManager: nmepm_pingReposURL: Cannot connect to http://serverxxx.university.edu:5500/em/upload/: retStatus=-32
    2005-02-11 16:18:05 Thread-1827 WARN http: snmehl_connect: connect failed to (serverxxx.university.edu:5500): A remote host refused an attempted connect operation. (error = 79)
    2005-02-11 16:18:05 Thread-1827 ERROR upload: FxferSend: Cannot connect to: http://serverxxx.university.edu:5500/em/upload/. retStatus=-32
    2005-02-11 16:18:05 Thread-1827 ERROR upload: Failed to upload file B0000197.xml, ret = -2
    2005-02-11 16:18:05 Thread-1827 ERROR upload: 3 Failures in a row for B0000197.xml, we give up
    2005-02-11 16:18:05 Thread-1827 ERROR upload: Error in uploadXMLFiles. Trying again in 123.00 seconds.
    2005-02-11 16:18:05 Thread-1717 WARN http: snmehl_connect: connect failed to (serverxxx.university.edu:5500): A remote host refused an attempted connect operation. (error = 79)
    2005-02-11 16:18:05 Thread-1717 ERROR upload: FxferSend: Cannot connect to: http://serverxxx.university.edu:5500/em/upload/. retStatus=-32
    2005-02-11 16:18:05 Thread-1717 ERROR upload: Failed to upload file B0000197.xml, ret = -2
    2005-02-11 16:18:05 Thread-1717 WARN http: snmehl_connect: connect failed to (serverxxx.university.edu:5500): A remote host refused an attempted connect operation. (error = 79)
    2005-02-11 16:18:05 Thread-1717 ERROR upload: FxferSend: Cannot connect to: http://serverxxx.university.edu:5500/em/upload/. retStatus=-32
    2005-02-11 16:18:05 Thread-1717 ERROR upload: Failed to upload file B0000197.xml, ret = -2
    2005-02-11 16:18:05 Thread-1717 WARN http: snmehl_connect: connect failed to (serverxxx.university.edu:5500): A remote host refused an attempted connect operation. (error = 79)
    2005-02-11 16:18:05 Thread-1717 ERROR upload: FxferSend: Cannot connect to: http://serverxxx.university.edu:5500/em/upload/. retStatus=-32
    2005-02-11 16:18:05 Thread-1717 ERROR upload: Failed to upload file B0000197.xml, ret = -2
    2005-02-11 16:18:05 Thread-1717 ERROR upload: 3 Failures in a row for B0000197.xml, we give up
    2005-02-11 16:18:05 Thread-1717 ERROR upload: Error in uploadXMLFiles. Trying again in 147.00 seconds.
    2005-02-11 16:18:05 Thread-1974 WARN http: snmehl_connect: connect failed to (serverxxx.university.edu:5500): A remote host refused an attempted connect operation. (error = 79)
    2005-02-11 16:18:05 Thread-1974 ERROR upload: FxferSend: Cannot connect to: http://serverxxx.university.edu:5500/em/upload/. retStatus=-32
    2005-02-11 16:18:05 Thread-1974 ERROR upload: Failed to upload file B0000197.xml, ret = -2
    2005-02-11 16:18:05 Thread-1974 WARN http: snmehl_connect: connect failed to (serverxxx.university.edu:5500): A remote host refused an attempted connect operation. (error = 79)
    2005-02-11 16:18:05 Thread-1974 ERROR upload: FxferSend: Cannot connect to: http://serverxxx.university.edu:5500/em/upload/. retStatus=-32
    2005-02-11 16:18:05 Thread-1974 ERROR upload: Failed to upload file B0000197.xml, ret = -2
    2005-02-11 16:18:05 Thread-1974 WARN http: snmehl_connect: connect failed to (serverxxx.university.edu:5500): A remote host refused an attempted connect operation. (error = 79)
    2005-02-11 16:18:05 Thread-1974 ERROR upload: FxferSend: Cannot connect to: http://serverxxx.university.edu:5500/em/upload/. retStatus=-32
    2005-02-11 16:18:05 Thread-1974 ERROR upload: Failed to upload file B0000197.xml, ret = -2
    2005-02-11 16:18:05 Thread-1974 ERROR upload: 3 Failures in a row for B0000197.xml, we give up
    2005-02-11 16:18:05 Thread-1974 ERROR upload: Error in uploadXMLFiles. Trying again in 176.00 seconds.
    2005-02-11 16:18:07 Thread-515 WARN http: 6,-1: nmehl_httpListener: signaled to exit from emctl

    Sathanga wrote:
    Hi,
    I have a Java application that runs on a Time clock (Hand held device). This app. has to be up and run all the times 24/7. After few days the app goes to hung stage, where we need to restart it manually. Is there a way, I can code within the app. itself, that restarts every night or so ....
    I searched through this forum earlier and did not get an answer. Appreciate your helps.
    Thanks
    SathThere is but a more important question is why does it quit every few days. Solve that problem and you'll be more ahead than with the solution you asked or originally.
    You can put the program on a timer and have ti launch every so often; you'll have to have it check to see if it's in memory when you do and if it is, then close the launcher and just let the previous running instance continue.

  • My apps shut down by itself

    My apps shut down by itself,this is very annoying when playing games etc.
    I have the 4G ipod touch

    Hi,
    Try a hard reset of your iPod:  Press/hold the *home* and *sleep/wake* buttons until the Apple logo appears. 
    Hope this helps! 

  • My iPhone 4 shuts down by itself

    I'm one of the few who are still using iPhone 4 , but anyway, I had this problem happened twice already today. The phone shuts down by itself. The screen becomes dead and black. I have to press and hold the wake/sleep button with the Home key at the same time for it to start. It works for a while, but then it happens again. Can anyone help? Appreciate it much.

    Hello there gilcelis99.
    The following Knowledge Base article offers up some great steps for troubleshooting the issue you're describing:
    iPhone: Hardware troubleshooting
    http://support.apple.com/kb/ts2802
    Particularly:
    Will not turn on, will not turn on unless connected to power, or unexpected power off
    Verify that the Sleep/Wake button functions. If it does not function, inspect it for signs of damage. If the button is damaged or is not functioning when pressed, seek service.
    Check if a Liquid Contact Indicator (LCI) is activated or there are signs of corrosion. Learn about LCIsand corrosion.
    Connect the iPhone to the iPhone's USB power adapter and let it charge for at least ten minutes.
    After at least 30 minutes, if:
    The home screen appears: The iPhone should be working. Update to the latest version of iOS if necessary. Continue charging it until it is completely charged and you see this battery icon in the upper-right corner of the screen . Then unplug the phone from power. If it immediately turns off, seek service.
    The low-battery image appears, even after the phone has charged for at least 20 minutes: See "iPhone displays the low-battery image and is unresponsive" symptom in this article.
    Something other than the Home screen or Low Battery image appears, continue with this article for further troubleshooting steps.
    If the iPhone did not turn on, reset it while connected to the iPhone USB power adapter.
    If the display turns on, go to step 4.
    If the display remains black, go to next step.
    Connect the iPhone to a computer and open iTunes. If iTunes recognizes the iPhone and indicates that it is in recovery mode, attempt to restore the iPhone. If the iPhone doesn't appear in iTunes or if you have difficulties in restoring the iPhone, see this article for further assistance.
    If restoring the iPhone resolved the issue, go to step 4. If restoring the iPhone did not solve the issue, seek service.
    Thanks for reaching out to Apple Support Communities.
    Cheers,
    Pedro.

  • MAC PRO shutting down by itself

    My mac pro keeps shutting down by itself, I can be doing anything and it just shuts down, now I tryed turning it back on it doesn't it keeps going on and off on and off so I unplugged it from the power supply, any ideas as of what it could be? Anyone?

    Unfortunately, I have no information on any ethical explanation as to why this is occurring, if you can provide any more information including everything you've done until the problem has occurred will be helpful to the resolution of your problem.. Once again, sorry about my inability to answer your question...

  • Airport Express shutting down by itself

    My AirPort Express is still shutting down by itself after using it for a while! I get a connection from my MacBook Pro for a while (green light), afterwards the LED is yellow and my Mac can not find the AirPort station anymore. So I restart the AirPort Express every time by switching it off. After this procedure it works for a while. Also restarts with the restart button do not help. The firmware is the new one; also the Mac has the latest version of OS.
    Please help - Thanks!

    So, the restart takes about 40 to 60 secounds. After restarting, the green lamp appears for few minutes and then restarting again (yellow lamp) and so on and so on. When I take the station off from electricity for a while the green period takes longer.
    Generally, the same problem appeared a couple of month ago, after playing around (I can't remember what) the station worked again, until I changed the place two days ago with disconnecting from power.
    So, maybe it's a software problem?

  • My macbook shut down from itself

    hi
    after i upgrade to mountain lion my macbook pro shut down from itself when i'm searching or doing somethin (weird proplem)!
    idk what's the proplem is it because i opened more than 2 apps (which i think it's a silly proplem if it's in the mountain lion)
    or because i connected my iphone 5 wirelessly with my my macbook!
    apple needs to fix this proplem, it happens everyday to me!
    what do you suggest?

    Hi,
    Try a hard reset of your iPod:  Press/hold the *home* and *sleep/wake* buttons until the Apple logo appears. 
    Hope this helps! 

  • My MacBook Pro (2.66GHz Corei7) shuts down by itself continuously

    My MacBook Pro (2.66GHz Corei7) shuts down by itself continuously

    Hi, I am facing the same issue.
    Did you able to solve your issue? Please advise.

  • MBP shutting down by itself

    Help!
    I don't know why my MBP shuts down by itself,
    the first time it happened was when i was burning something from idvd
    then it happened again when I was just typing something, then again when I was just surfing. Then when i tried to turn it on, it went off again..then finally it is working now.
    Is it possible this is happening because of the replacement batteries? i bought my MBP last february when it went out, so it is part of the battery recall. right now im using the replacement. what should i do?
    Macbook Pro   Mac OS X (10.4.7)  

    It's not the battery. Many of the Mac Books have a far more serious problem with their internal hardware.
    The first thing i suggest is repair your permissions.
    Secondly, make sure you have updated firmware.
    Thirdly, try reseating your ram.
    Last, alert Applecare. Tell them your problem, and the steps you have taken.
    It is likely that you will need to:
    a.) have your logic board replaced (it will take about a week, including shipping)
    or b.) need a replacement.
    I just went through all of this. If you want me to walk you through anything, just let me know.

  • Why does my MBP 13" 2012 screen shuts down by itself?

    The screen of my MBP 13" shuts down by itself, more and more often. It does not happen in a specific situation, and the laptop continues running and receiving inputs. In order to reactivate the screen I have to open and close it several times, or press the power button.
    The screen turns completely back and the led outside start blinking like when I close the laptop.
    The MBP is new, bought in summer 2012 and does not have any other program installed than the standard ones. I have no idea why this happens but it is occurring more and more.
    Do you have any idea?

    You are still under warranty.  Call Apple Care. Make sure you get a case number as all repairs have an additional 90 days of warranty. 
    #1 - You have 14 days from the date of purchase to return your computer with no questions asked.
    #2 - You have 90 days of FREE phone tech support.
    #3 - You have the standard one year Apple warranty.
    #4 - If you've purchased an AppleCare Protection Plan, your warranty last for 3 years.   You can obtain AppleCare anytime up to the first year of the purchase of your computer.
    Take FULL advantage of your warranty.  Posting on a message board should be done as a last resort and if you are out of warranty or Apple Care has expired.

Maybe you are looking for

  • Purchase Order Total Amount at Header level and Report Execution

    Dear Experts, Here by i am facing problem with Purchase Order Total amount. I have local Pricing Procedure for price stipulations (like discounts, Freight, packaging). the calculation at item level is correct. tax calculation is done by tax code. The

  • BADI or BAPI Getting Trigerred at the time of PO approval or Creation

    Hi Gurus,                Can Anyone of you just guide me by giving one or more BADIs name that are getting trigerred at the time of PO approval or before Ordered. I am in the nick of the project. Please help urgently. Points will be rewarded. Thanks

  • What is material yeild ?

    Hi Gurus,        plz let me know what is material yeilding , is there any standard program to know the same or if any one can provide me the sample code for the sam e..it will be of great help for me ... thanks in advance. regards, Vikram

  • Hyper V Manager enhancement

    scenario old Dell laptop installed with Hyper V server 2012 R2 core  in a 32GB partition Windows 8.1 Hyper V Management console no ability to create an additional storage partition from the remaining disk space of the laptop to allow separation of VM

  • Is icloud down?, is icloud down?

    Can't get icloud emails to work today 11/9/12. Is the problem elsewhere?