A58M-E33 MB wont install Win7 OS

The Win 7 Pro 64 bit installer starts up fine. After selecting language/country, etc. It pops up with message on next screen saying drivers are required for the DVD/CD device, insert the disk with the drivers!  The driver that Win7 is using is obviously working. I searched the internet and found 2 possible work-around for this. First, I tried initially setting the boot drive (SSD) as no1 priority, and the DVD as no. 2. This did not get me past the problem, same thing. So I tried the second thing....in BIOS, changed DVD transfer mode from IDE emulation to AHCI. This also did not fix the problem either.  I swapped in a different /older SATA DVD (only) drive, same result. Tried another Win7 Pro. install disk from another source, same result. SO its pointing to it being a problem with the mobo.  Back online searching and found a couple post that said it could be the sata drivers are not supported. I downloaded and updated the sata drivers. Same window pops up. My bios is 32.5 atm. I also tryed to load the win7 onto a usb and then install and still get stuck with a pop up that says device not supported. In desperation I went to windows download and tried to download a fresh copy of win7. Only to be told that my disk was OEm and to contact the supplier, who then told me to contact Microsoft. I also tried removing the HD and installing a 128gig flash-drive as primary drive, with and with out OS already installed. The Hd has been wiped clean, replaced, and has had OS preinstalled with no luck. I have switched around evey option I can in the bios and tried every comb of bios and hardware swap I can think of. Nothing works. Still stuck.  It is my opinion that the motherboard has a driver or bio issues with the SATA support. however I am not sure how to fix it?
MSI contacted YES ( no replie back)
Microsoft says its OEM contact supplier
Supplier says its 1 copy full install and to contact Microsoft.
Updated and installed Bios and drivers.
Wiped Bios clean, wiped HD clean and started fresh several times
Even tried a XP install ( same thing)
New Build
A4-7300 AMD 3.8
Adata ddr3 at 4 gig
seagate 2 TB sata HD
DvD- R Samsung or generic one. ( have replaced with others)

tried installing Win764bit with bios boot set to legacy and not UEFI mode. ( tried this several times with Hardware changes and from fresh start on all settings.)
boot priority to dvd and only dvd if you are using dvd. Deselect booting to HDD in the whole boot list. ( I did this and also completely removed Hd and instead used a flash drive to load to.)
 installing Win 7 from a bootable USB and DVD with all updates on it. ( I have done this many times,  with every possible configuration I could think of.) However came up with pop up that device drivers were needing installed Vs. Cd/Dvd drivers needing installed.
I have been on this for 2 weeks solid. I am about to just chuck the MB and order a replacement at this point. This is my first build with new parts and was a test. To see how far my computer building skills were behind all the up to date tech. I usually find my pc builds in the garbage or someones old pc they dont want. I have never had this much trouble getting drivers, bios or OS to install. I have a few ideas that I am about to try. I will update with the results. Thanks for your reply..

Similar Messages

  • CS4 Master Collection wont install on Vista Ultimate 64-bit.

    Im using my friends cs4 disc's wich he doesent use any more (switched from windows to mac) and it wont install
    full quality image atached if you cant read this one.

    This is a very close friend we've been working together since high school. but other than that dont you have any ideas whatsoever?
    or is there any way to skip the system profile check, cause i'm prity sure my system is more than adiquate to run cs4
    3.16ghz duo core, 4gb ram, 1gb ati radeon his hd4670.

  • Installing Win7 on a macbook pro using a mac mini as external optical drive

    hi everyone,
    My 2 year old son watches movies on my macbook pro. He stuck something in the optical drive making it unusable. Repairing it is 200 to 300 euros (ouch).
    I want to install win7 via bootcamp and I'm using my mac mini (october 2009) as an external optical drive. These are my steps:
    1.hold the "t" on the mac mini
    2.connect it to the macbook with a firewire 800 to firewire 400 cable
    3.Power up and hold the "alt" on the macbook
    4.I see the optical drive on the boot screen and I choose it
    5.Then I get a blank screen and a few seconds later the "missing operating system" message appears.
    Am I missing something? Is it possible to install win7 using a mac mini as an external drive?
    PS1:I already have partitioned the HD with bootcamp.
    PS2:I've upgraded the hard disk drive of the macbook with a seagate momentus 500GB hard disk. Don't think this is the problem, thought I should mentioned it.

    Hi Mike,
    For reference it is called "IP over Firewire".
    Connect the two computers with a fire wire cable. System Preferences > Network > Configure IPv4: > Manually > IP address: 192.168.3.1 (and .2 on other) > Subnet Mask: 255.255.255.0. Leave the other fields blank. Do this on both computers on the computer you want to allow access to or both for two way access go to System Preference > Sharing > Select a service to change its settings. Turn remote Login on.
    On the MBP go to the Finder Menu > Go > Connect to Server > Type in the IP address of the Mini 192.168.3.2 (Whatever you gave it)
    With this configuration you still have full use of the Mini and certain apps can use Xgrid and use the processor of the mini when it is not doing anything. I would keep the Mini as 10.4 unless you really need both machines running Leopard. As noted before you cannot boot the MBP from a HDD that is Apple Partition Scheme and vice versa you cannot boot the PPC from a Guide Partition Table.
    Sweet Polly

  • Z87-G45 Gaming not able to install Win7 x64 with Samsung 840 EVO

    I have a brand new:
    i5 4570
    MSI Z87-G45 Gaming
    250GB Samsung 840 EVO
    1x 8GB Corsair ValueRam DDR3 1600
    I got everything hooked up properly, but I am not able to install Win7 x64 through an USB pen drive (Kingston Datatravel 32GB USB3) I have a proper  official and Legit MSDN ISO, formatted by the Win7 USB tool from MS itself.
    Note that i do not have an optical device (DVD) installed so I cannot use it 'the old way'.
    Bios settings are okay, everything is recognized
    USB Legacy - Kingston Datatraveler
    HDD Legacy - Samsung 840 EVO
    Win7 setup loads properly; but before I can select the Harddrive / SSD to install Win7 on I get prompted that additional (3rd party) drivers are needed to proceed. The volume is not recognized. This happens 9 out of 10 times. In the 10% cases I do get the option to format the SSD and/or create partitions. However, installation fails after all, cannot load or find file ...
    What I've tried so far:
    Switch out the SATA cables and power cables
    Switch through the various SATA ports on the MB 1 through 6
    Tried UEFI and UEFI/Legacy (UEFI doesn't seem to work at all)
    Update UEFI to V 1.50
    All the above result in the case mentioned.
    I have succesfully installed the SSD in an other PC, using the same pen drive and ISO and it worked like a charme, thus ruling out that the SSD, pen drive or image is corrupt.
    Even when I switched out the SSD after Win7 setup has succesfully copied, unpacked and installed all the files (doing this on the other machine where it works like a charm). Then switching it to the MSI Z87...it fails; starting the setup procedure right from the start, like nothing was ever written on the SSD...
    Finally i turned to Win8, and guess what, it installed without any glitches on the MSI Z87
    What am I missing here, I would really want to install Win7 instead of Win8
    Forgot to enable / disable something in the UEFI? I really don't know, google doesn't give much information on this specific problem (SSD is recognized properly by the BIOS / UEFI as far as I can tell)
    The only thing I have not tried out so far is updating the Samsung SSD firmware to the 1.0 version which has been release 3 days ago...
    Any clues, tips, hunches??

    Quote from: Bernhard on 25-October-13, 18:33:41
    Did you disable Secure Boot in the BIOS? If not, then Win7 won't load.
    Hmmm not sure, thanks for the reply, will have to look into that later today!
    I didn't change it from the default setting I think, unless it is part of the Win8 features in the UEFI. All where disabled by default, and I kept them disabled.
    Where is Secure Boot listed in the UEFI, and any idea wether it is enabled by default?
    ::EDIT::
    Found it in some screenshots, I cannot recall from the top of my head wether it was enabled or disabled, allthough my gutt feeling says it already is disabled.
    http://cdn.pcper.com/files/imagecache/article_max_width/review/2013-05-31/09-MSI_SnapShot_23.gif
    http://cdn.pcper.com/files/imagecache/article_max_width/review/2013-05-31/10-MSI_SnapShot_24.gif
    Nice overview of the entire UEFI btw: http://www.pcper.com/reviews/Motherboards/MSI-Z87-GD65-Gaming-Motherboard-Review/BIOS-Features-continued

  • I wanted to update my itunes and it didn't update and now it wont open so i had to uninstall it and it wont install now at all can you please help?

    Hi
    I turned on my laptop this evening to import a new cd but it asked me if i wanted to download the new version of itunes so i went ahead to update it but it failed to update then it failed to open at all, and and runtime error keeps popping up but when i uninstalled it to reinstall it it wont install now and i cant use my ipod or ipad with my laptop without itunes and i never had this problem at all. can you please help?

    Hey maryncomiskey,
    Thanks for the question. I understand you are experiencing issues with the latest iTunes update. The following resource may help to resolve your issue:
    Issues installing iTunes or QuickTime for Windows
    http://support.apple.com/kb/HT1926
    Additional Information:
    How to restart the Apple Mobile Device Service (AMDS) on Windows
    http://support.apple.com/kb/TS1567
    Thanks,
    Matt M.

  • Hi i am trying to install itunes and it wont install due to error code 2349 how do i fix this issue

    i have tryed on numerous occasions to install itunes and it sometimes installs but then i cant use it due to error code 2349, so i uninstall and try again and wont install it at all due to error code 2349 please help i really eant to use my ipod

    Refer to this thread:
    https://discussions.apple.com/thread/3174150?start=0&tstart=0

  • TS5376 iTunes wont install.  It says " The program can't start because MediaAccessibility.dll is missing from your computer.  Try reinstalling the program to fix this problem."  I have uninstalled iTunes 5 times and reinstalled it, and nothing has worked.

    iTunes wont install.  It says "The program can't start because MediaAccessibility.dll is missing from your computer.  Try reinstalling the program to fix this problem."  I have uninstalled iTunes 5 times and reinstalled it, and nothing has worked.  Help!!!!

    Click here and follow the instructions. You may need to completely remove and reinstall iTunes and all related components, or run the process multiple times; this won't normally affect its library, but that should be backed up anyway.
    (99683)

  • Satellite A300 (PSAG8E) - Hardware problems after installing win7 ultimate

    Hello and good day,
    I've installed win7 ultimate a few days ago and windows managed to recognize most of my hardware accept my build in mic and camera and another component I am not sure about what it is (Windows update automatically downloaded the sound and graphics driver for me).
    My questions are - where can find the remaining drivers and where can I get the preinstalled Toshiba tools and software? (The driver site in the Toshiba support page does not include those drivers and software)
    Thank you very much
    Roi Ben Simon

    Hi
    I have Satellite A300 (PSAG8E) too and installed Win7 Home premium and everything works perfect.
    At first I must say that I don't know where you have searched drivers and Toshiba tools and utilities because all stuff is downloadable on Toshiba support & download page under http://eu.computers.toshiba-europe.com
    It is logic that mic will not work if you didn't installed proper driver. Install drivers alone and not using Microsoft update. What you need are real and tested drivers and not some free drivers from internet.
    Go to Toshiba download page and install all stuff following this installations order:
    -Win7
    -chipset driver
    -storage manager
    -display driver
    -sound driver
    -modem driver
    -supervisor utility
    -infrared
    -patches
    -configfree
    -VAP
    -toshiba hardware setup
    -HDMI control
    -WLAN driver
    Everything works well but missing some drivers
    Added Vista stuff:
    -Toshiba assist - work properly
    -Card reader - installed properly
    -Webcam driver for A500 - tested with Skype - work properly.
    -Synaptics driver

  • Fn+b keys don't work after installing Win7 Ultimate (HP Envy 14 BE)

    Fn+b keys don't work after installing Win7 Ultimate (HP Envy 14 BE)  --not able to use the Beats Speakers. Any software updates I need to install?
    This question was solved.
    View Solution.

    Hi Jim,
    You're welcome
    Is the version of Windows 7 Ultimate you have installed 32bit or 64bit?
    Open windows Control Panel, open Device Manager and open up Sound, Video and Game Controllers - do you see an existing entry for the IDT High Definition Audio CODEC listed here?
    There is an alternative IDT Audio driver you may wish to try on the following link.
    http://ftp.hp.com/pub/softpaq/sp53001-53500/sp53281.exe
    Let me know if you get the same error with this version.
    Regards,
    DP-K
    ****Click the White thumb to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    ****I don't work for HP****
    Microsoft MVP - Windows Experience

  • Hi im having huge problems trying to install flash for my mac 10.5 imac, iv gone through the internet and tried all of the solutions, everytime i try to install flash it says cant read the download file, or it just wont install, anybody plz help!

    hi im having huge problems trying to install flash for my mac 10.5 imac, iv gone through the internet and tried all of the solutions, everytime i try to install flash it says cant read the download file, or it just wont install, anybody plz help!
    iv unistalled flash, iv checked plug ins it just wont work,

    It would have been a great help to know precisely what Mac you have, so some of the following may not apply:
    You can check here:  http://www.adobe.com/products/flash/about/  to see which version you should install for your Mac and OS. Note that version 10,1,102,64 is the last version available to PPC Mac users*. The latest version,10.3.183.23 or later, is for Intel Macs only running Tiger or Leopard, as Adobe no longer support the PPC platform. Version 11.4.402.265 or later is for Snow Leopard onwards.
    (If you are running Mavericks: After years of fighting malware and exploits facilitated through Adobe's Flash Player, the company is taking advantage of Apple's new App Sandbox feature to restrict malicious code from running outside of Safari in OS X Mavericks.)
    * Unhelpfully, if you want the last version for PPC (G4 or G5) Macs, you need to go here:  http://kb2.adobe.com/cps/142/tn_14266.html  and scroll down to 'Archived Versions/Older Archives'. Flash Player 10.1.102.64 is the one you download. More information here:  http://kb2.adobe.com/cps/838/cpsid_83808.html
    You should first uninstall any previous version of Flash Player, using the uninstaller from here (make sure you use the correct one!):
    http://kb2.adobe.com/cps/909/cpsid_90906.html
    and also that you follow the instructions closely, such as closing ALL applications (including Safari) first before installing. You must also carry out a permission repair after installing anything from Adobe.
    After installing, reboot your Mac and relaunch Safari, then in Safari Preferences/Security enable ‘Allow Plugins’. If you are running 10.6.8 or later:
    When you have installed the latest version of Flash, relaunch Safari and test.
    If you're getting a "blocked plug-in" error, then in System Preferences… ▹ Flash Player ▹ Advanced
    click Check Now. Quit and relaunch your browser.
    You can also try these illustrated instructions from C F McBlob to perform a full "clean install", which will resolve the "Blocked Plug-in" message when trying to update via the GUI updater from Adobe.
    Use the FULL installer for 12.0.0.44:  Flash Player 12 (Mac OS X)
    And the instructons are here: Snow Leopard Clean Install.pdf
    (If you are running a PPC Mac with Flash Player 10.1.102.64 and are having problems with watching videos on FaceBook or other sites, try the following solution which fools the site into thinking that you are running the version 11.5.502.55:)
    Download this http://scriptogr.am/nordkril/post/adobe-flash-11.5-for-powerpc to your desktop, unzip it, and replace the current Flash Player plug-in which is in your main/Library/Internet Plug-Ins folder, (not the user Library). Save the old one just in case this one doesn't work.

  • What is the 0x80070570 error when installing Win7 or Win8 or Win 8.1 on a clean SSD/HDD ?!

    Hello,
    My computer was working perfectly with Win7 for about 2years until I formatted on monday to clean a little bit my drives ... Since then I'm unable to install windows again. I have the 0x80070570 error.
    The complete error message is:
    Windows cannot install required files. The file may be corrupt or missing. Make sure that all files required for installation are available and restart the installation. Error code:0x80070570.
    What is the 0x80070570 error when installing Win7 or Win8 or Win 8.1 on a clean SSD/HDD ?! These versions are full from MSDN.
    What I did already:
    check my RAM (16go gskill)
    remove unnecessary hard drives
    replace my "old" SSD with a clean new one
    remove my sound cards
    remove the mouse and use only keyboard
    reset the BIOS
    check every LED on the motherboard (asus sabertooth z77) and there is no problem
    What are the problems?
    Thanks,
    Adrien.

    Hi,
    If all images cannot be installed, we have a reason to suspect the hardware cause.
    If you use two memory slots to get 16G RAM, I suggest you test with just one (8G) to check the result.
    Alex Zhao
    TechNet Community Support

  • Having problem installing Win7 using Bootcamp on Mac Mini 2011

    I'm trying to install Win7 using bootcamp on my new Mac Mini 2011. I first partitionned the disc using Bootcamp assistant. Then during Win7 installation I select Partition 4 BOOTCAMP, format it to NTFS, then when I try to select the drive, it says that the drive is not compatible for the installation.
    Is there anything I missed???
    Thanks

    I had a similar problem when I selected upgrade instead of complete install. I want to make sure your aware that you should click the complete option instead of upgrade when you reach that portion of the win7 install. Then you need to select part ion 4 like you have stated and format it to ntfs.
    But it seems that you've already done all of that. My advice would be to go back to the Mac side, restore the partition using bootcamp and again partition it. You need at least 25gb of space for 64 bit. I would recommend using at least 40gb. Just trying to help. I apologize if I misunderstood your problems. But make sure you click on the opposite choice of upgrade, I did my mini last night lol but I can't remember the exact name of the option I think it's complete, then select part 4 and click format....

  • ITunes will download but wont install on windows 7 64-bit computer.

    I got this computer a few weeks ago and first thing i tried to install was iTunes off of the apple site and it wont install.
    i can download the setup file to my computer and save to my documents but when i right click and click run as administrator, a loading sign will appear for two seconds then disappear... i need iTunes on this computer since it wouldnt install on my old laptop. i've even tried installing on safe mode and nothing. i just want iTunes on my computer.. any help?

    Same issue here and unfortanetly no one yet has an answer...

  • IMac 27" running OS 10.6.7 trying to install Win7 error message 0x80070017

    Hi all,
    For the last 10 hours I have been trying to install Win7 on my iMac 27".  After finding the solution to the black screen issue and getting through to selecting which version of Win7 I'd like to install blah blah, it starts writing the files and then I get the error message 0x80070017.  I have searched here for an answer but the only one I can find dates back to 2008 and has me baffled.   Is there something I can do?  I need this programme to run MS Publisher for my daughter's school projects, otherwise I'd take it back and feed it  down some Microsofts (better stop here).  Have been using Boot camp 3.0 to do the install.
    iMac 2.8GHz Intel Core i7  OS 10.6.7.

    Hi Bob,
    Win7 Home Premium, full retail version purchased today (now yesterday).  Black screen problem resolved by using a USB stick with a copy of the drivers folder and Autounattend.xml file from iMac_late_2009_2010_Win7_Drivers download. As per a discussion thread from this forum.
    Followed Boot Camp to the letter, several times.
    Windows disk damaged/dirty... no.
    As for the complete error message there was more to it than the numbers, something about unable to complete, but to get it the exact wording will take another hour or so while I reinstall it again (for the 6th time).
    Boot Camp partition size is 52Gig
    From what I can gather the problem is more than likely not on the install disk but rather on my hard drive, a bad sector or such thing, as Windows is more able to detect disk errors; so I've read anyway.  I am thinking of removing the partition and repairing permissions etc using disk utility and see what happens.  I did have Disk Warrior for my old G4 but that programme doesn't work for later versions of OSX.  Other than that I'm stumped.

  • Cannot install Win7 on my Qosmio F50

    HI,
    I hope you can help me in my problem. I have Laptop Old Qosmio F50-10G Model #. PQF55E-00V012AR. It's installed windows vista home premium. For my desired to change my OS to windows 7, I reformat it true proper installing.
    the problem is, It can't be install any operating system even win XP and win Vista.
    Window Vista and Windows 7 it page that I load the system to hard drive. it can't detect the hardisk. I try to install the AHCI driver of it but its failed, now even windows xp cannot install, it is error when it reach starting windows.
    What can I do so i can installed any of operating system?
    Please help.

    I really dont know what is wrong there. Set BIOS to default settings and try to install Win7 again.
    Do you use original Microsoft install disc?
    Start notebook and press F12 to enter boot menu. When the menu is shown on the screen put Win7 disc into ODD, choose CD/DVD drive and press enter button.
    What happen exactly when you do this?

Maybe you are looking for