A75MA-P35 C6 Mode Problem

Hi,
Just purchased a A75MA-P35 and amd 3500 Lano cpu and 8GB Corsair ram
And have a problem with my A75MA-P35 -( Problem when enabling C6 Mode in bios.)
Motherboard already had latest bios 1.2.
MSI Install CD was full of errors when i tried to install drivers,(totally corrupted,,(screwed) and lots of scratches on the surface.
I just downloaded from the internet drivers needed but still a pain.
When i enable c6 mode in bios and save and exit, Win7 starts after a few seconds, the computer Reboot's and Reboots, etc.
As soon as i disable C6 Mode, computer start's fine.
is there a Problem with the bios and C6 Mode
Also CPU temperature in win7 reports 8c , i think is a bit on the cool side, is generally not a problem, but CPU fan never changes speed in windows.
If i run a game or something then the CPU is in fact red hot, simply because the temps being reported in win7 are only 8c and the computer mobo thinks the fan speed
doesn't need to go any faster.
I have the fan speed set to increase when the CPU hits 40c , the lowest temp setting in bios but the CPU fan never changes speed.
Don't know if its just my motherboard or a general problem with this mother :bonk:board.
Any thoughts or help would be appreciated..
Many Tks..
https://forum-en.msi.com/Smileys/msi/bonk.gif

Ok svet tested beta bios E7697AMS.14A
Sorry to tell you that Reboot Loop error when starting win7 is still there in Bios test E7697AMS.14A
Tested with C6Mode enabled (Reboots when starting win7)
Tested with C6Mode Disabled (Reboots when starting win7)
Tested with svm Disabled ( Reboots when starting win7)
Tested with cool and quiet Disabled (Reboots when starting win7)
Windows 7x64 Reboots after about 3 seconds when you see the win7 flashing icon in center of screen
and will continue to repeat Reboot etc.
So it looks like bios E7697AMS.14A is worse than the Latest Official Bios 7697v12.
We tried svet, i will pop back here every day to see if we can get a fix.
Many tks svet..
The Test bios E7697AMS.14A has been installed correctly in dos mode , bios reset with jumper on motherboard before testing E7697AMS.14A.

Similar Messages

A75MA-P35 and ganged mode

Hi to all,
I've got this problem: I'm using a A75MA-P35 motherboard that seems to work fine, but in the first post message, about DDR mode, I read "GANGED MODE, 64 BIT".
Well, I use 2 sticks of Kingston DDR3 memory (freq. 1333 mhz). In similar boards I always see "ganged, 128 bit". can you please explain me the reason of those 64 bits (usually 64 for unganged mode, 64 + 64 for ganged)?
I tried two versions of bios (1.10 and 1.20)... same values
thanx for support
Paolo

Great!!! I supposed it was not a problem but a characteristic of my system...but did not find anything about this issue. You were able to do this... great.
by the way I repair and assembly pcs as a Job, and when I learn something new I'm happy
thanx again for your time and availability
peace,
Paolo
PS: I use this system as a "portable" little home audio recording station... reason, cubase ecc with an M-AUDIO Fast track USB.
This is the first time I use AMD for audio...no latency... good as a much more expensive INTEL

Eithernet problems with A75MA-P35

I am having trouble with the network adapter on my A75MA-P35 FM1 AMD A75 (Hudson D3). I purchased the motherboard on March 9, 2012. It has been working fine until today. I am running Windows 7 64bit. The network connection would be on for a minute when the computer boots but then windows shows that it becomes disconnected, but the lights on the port still remain solid on. Windows driver says that the drivers are working fine. I swapped network cables that is working fine with another computer but the problem still remains on this computer. Is there a utility to test the network port
Thanks

Please see my post here:
https://forum-en.msi.com/index.php?topic=159490.0
I am experiencing the same problem. You can also see the problem described in the newegg review for this board. Note that the A75MA-P35 and the A55M-P35 are the same boards except for the chipset, and they even use the same BIOS.
For now, I suggest you use a PCI network card.
I don't think MSI can fix this with a BIOS, I think they're going to re-release it with a new hardware revision.

A75MA-p35 Raid 1 Install Win7 drivers not found

Hi all,
Looking for a bit of help here, Problems installing Win7 Home Prem on a mirror raid. I followed the PDF manual uk.msi.com/product/mb/A75MA-P35.html#/?div=Manual to the letter for how to create the raid, But the issue is cant seem to find any drivers to detect the HDDS, Or The DVD drive for that matter.
I have:
Set BIOS SATA mode to : Raid
Used the BIOS CTRL+F Option, to create the raid. ( RAID Option ROM utility... )
Booting from Win7 CD, Its asking for drivers for the drives The PDF above says use the driver from >
: \\ChpSet\AMD\Packages\Drvers\SBDrv\SB8xx\RAID\
(and then, please select a folder whch was classfied accordng to OS.) "
This I have tried, But Its not listed due to the "Incompatible driver" Checkbox.
I have tried forcing it to install this driver, and others from the CD/Net But with no luck
Anyone got any clues?
Thanks

Link worked.
Thanks for the help. Much appreciated.
Tis all installing now.
Confused to why the drivers from the motherboard CD didnt work tho?
@Xmad.
The USB stick was showing up fine pal, Just the drivers I was throwing at it, Didnt want to work. I did try installing the other drivers to see if they worked anyway with no luck.
Sigh, whilst writing this. More errors on screen :( Back shortly!

MSI A75MA-P35 Signal Lost, No DVI

Mainboard: MSI A75MA-P35 (unknown BIOS - due to no video).
AMD A4-3300 Llano Dual-Core 2.5GHz
WD Blue WD5000AAKX 500GB
Corsair XMS3 8GB
Windows 7 Pro x64
So I built this PC for my grandmother in 2012 and everything has worked flawlessly until this past week; she said the screen went black and a sound came on, so I logged into her PC through teamviewer and the screen would change resolutions every 3 seconds on my end, I was able to update everything (tedious I must say).
Still no video. So I brought her PC over here and tested it with my monitor; no joy on the DVI port, intermittent on the VGA so I did some cleanup in safe mode and then booted it up on VGA and it was working fine. Hooked it up for her; was working fine, then over night same problem appeared.
I do not have a second CPU to test with, but the CPU is actually working (because I can connect through TeamViewer). I'm honestly thinking the board has issues, it's still under warranty, but I wanted to come here and see if anyone else has had similar problems.
Though if I throw an FM2 board in there with a new FM2 APU, do I have to do a clean install on Windows (yes I know you should when you change hardware); I just want to make this as minimal hassle as possible.
Further notes:
No POST beeps
Everything seems to be working fine just no video.
DVI port is hard to connect (bent - though I don't know if it's a factory defect)

Since the screen is black when connected to DVI before Windows even starts booting, I would say what it isn't a Windows issue. I thus highly doupt what a re-install would fix it.
Quote from: midnightwolf76
the screen would change resolutions every 3 seconds on my end
From the sound of it, it sounds like the motherboard (or APU) is unable to detect the Screen frequency & resolution, causing it to try different ones (thus the swapping).
Quote from: midnightwolf76
DVI port is hard to connect (bent - though I don't know if it's a factory defect)
Might be damaged, that could explain the issue. First see if you can find any visible signs of damage. Then check for broken pins being stuck or bent pins on the cable. Might need to get the board replaced or repaired, however check if any of the mods have anything to say about it first.

TLS mode problem

Hi i am trying to fetch a mail from my Zimbra account. But i am getting the following error.
What is this TLS mode problem? please help.
javax.mail.AuthenticationFailedException: only valid after entering TLS mode
at com.sun.mail.pop3.POP3Store.protocolConnect(POP3Store.java:146)
at javax.mail.Service.connect(Service.java:297)
at javax.mail.Service.connect(Service.java:156)
at javax.mail.Service.connect(Service.java:105)
at FetchMail.receive(FetchMail.java:40)
at FetchMail.main(FetchMail.java:193)

Hi i am trying to contact Our Zimbra server to retrieve the mails from Inbox, I used pop3 as protcol .. before but it was throwing an error
javax.mail.AuthenticationFailedException: only valid after entering TLS mode
     at com.sun.mail.pop3.POP3Store.protocolConnect(POP3Store.java:146)
     at javax.mail.Service.connect(Service.java:297)
     at javax.mail.Service.connect(Service.java:156)
     at SampleZimbraSMTP.postMail(SampleZimbraSMTP.java:44)
     at SampleZimbraSMTP.main(SampleZimbraSMTP.java:22)
so i changed to pop3s & downloaded new jars. I am pasting the code here
import java.util.Date;
import java.util.Properties;
import javax.mail.*;
import javax.mail.internet.*;
import javax.mail.Authenticator;
import javax.mail.Folder;
import javax.mail.Message;
import javax.mail.Multipart;
import javax.mail.Part;
import javax.mail.PasswordAuthentication;
import javax.mail.Session;
import javax.mail.Store;
import javax.mail.Transport;
import javax.mail.internet.InternetAddress;
import javax.mail.internet.MimeBodyPart;
import javax.mail.internet.MimeMessage;
import javax.mail.internet.MimeMultipart;
public class SampleZimbra {
     public static void main(String args[]){
          try {
               SampleZimbra zm = new SampleZimbra();
               zm.postMail();
     catch (Exception e) {
               e.printStackTrace();
     private boolean debug = false;
     public void postMail() throws Exception {
          Properties props = new Properties();
          Authenticator auth = new ZimbraAuthenticator();
          Session session = Session.getDefaultInstance(props, auth);
          session.setDebug(debug);
          Store store= session.getStore("pop3s");
          store.connect("ip address","username","password");
          Folder folder = store.getFolder("INBOX");
          folder.open(Folder.READ_ONLY);
     // Get directory
     Message message[] = folder.getMessages();
     for (int i=0, n=message.length; i<n; i++) {
     System.out.println(i + ": "
     + message.getFrom()[0]
     + "\t" + message[i].getSubject());
     // Close connection
     folder.close(false);
     store.close();
class ZimbraAuthenticator extends Authenticator {
     public PasswordAuthentication getPasswordAuthentication() {
          return new PasswordAuthentication("username", "password");
After this code compiles & when i try to run it throw me the following error..
javax.mail.MessagingException: Connect failed;
nested exception is:
     javax.net.ssl.SSLHandshakeException: sun.security.validator.ValidatorException: PKIX path building failed: sun.security.provider.certpath.SunCertPathBuilderException: unable to find valid certification path to requested target
     at com.sun.mail.pop3.POP3Store.protocolConnect(POP3Store.java:148)
     at javax.mail.Service.connect(Service.java:275)
     at javax.mail.Service.connect(Service.java:156)
     at SampleZimbraSMTP.postMail(SampleZimbraSMTP.java:44)
     at SampleZimbraSMTP.main(SampleZimbraSMTP.java:22)
Caused by: javax.net.ssl.SSLHandshakeException: sun.security.validator.ValidatorException: PKIX path building failed: sun.security.provider.certpath.SunCertPathBuilderException: unable to find valid certification path to requested target
     at com.sun.net.ssl.internal.ssl.Alerts.getSSLException(Unknown Source)
     at com.sun.net.ssl.internal.ssl.SSLSocketImpl.fatal(Unknown Source)
     at com.sun.net.ssl.internal.ssl.Handshaker.fatalSE(Unknown Source)
     at com.sun.net.ssl.internal.ssl.Handshaker.fatalSE(Unknown Source)
     at com.sun.net.ssl.internal.ssl.ClientHandshaker.serverCertificate(Unknown Source)
     at com.sun.net.ssl.internal.ssl.ClientHandshaker.processMessage(Unknown Source)
     at com.sun.net.ssl.internal.ssl.Handshaker.processLoop(Unknown Source)
     at com.sun.net.ssl.internal.ssl.Handshaker.process_record(Unknown Source)
     at com.sun.net.ssl.internal.ssl.SSLSocketImpl.readRecord(Unknown Source)
     at com.sun.net.ssl.internal.ssl.SSLSocketImpl.performInitialHandshake(Unknown Source)
     at com.sun.net.ssl.internal.ssl.SSLSocketImpl.readDataRecord(Unknown Source)
     at com.sun.net.ssl.internal.ssl.AppInputStream.read(Unknown Source)
     at java.io.BufferedInputStream.fill(Unknown Source)
     at java.io.BufferedInputStream.read(Unknown Source)
     at java.io.DataInputStream.readLine(Unknown Source)
     at com.sun.mail.pop3.Protocol.simpleCommand(Protocol.java:347)
     at com.sun.mail.pop3.Protocol.<init>(Protocol.java:91)
     at com.sun.mail.pop3.POP3Store.getPort(POP3Store.java:201)
     at com.sun.mail.pop3.POP3Store.protocolConnect(POP3Store.java:144)
     ... 4 more
Caused by: sun.security.validator.ValidatorException: PKIX path building failed: sun.security.provider.certpath.SunCertPathBuilderException: unable to find valid certification path to requested target
     at sun.security.validator.PKIXValidator.doBuild(Unknown Source)
     at sun.security.validator.PKIXValidator.engineValidate(Unknown Source)
     at sun.security.validator.Validator.validate(Unknown Source)
     at com.sun.net.ssl.internal.ssl.X509TrustManagerImpl.checkServerTrusted(Unknown Source)
     at com.sun.net.ssl.internal.ssl.JsseX509TrustManager.checkServerTrusted(Unknown Source)
     ... 19 more
Caused by: sun.security.provider.certpath.SunCertPathBuilderException: unable to find valid certification path to requested target
     at sun.security.provider.certpath.SunCertPathBuilder.engineBuild(Unknown Source)
     at java.security.cert.CertPathBuilder.build(Unknown Source)
     ... 24 more
Can any one guide me to resolve this....
Thanks
Bharathi.
Message was edited by:
bharathi

More design mode problems

I've been down this road before but now it's getting just crazy. I can't get work done if I want to create a simple layout. I've created new workspaces, cleaned, everything I can think of including taking out any third-party components that might possibly be compiled in non 4.5.1 (though they supposedly have).
I try to create a simple MXML component. If it's based on anything visual (e.g., panel) or if I start with a group and then drag in a panel, I just get the little computer icon with red x on it in design mode with the following errors in the Design Mode Problem panel. I mean, this is just a new, empty component.
Assets failed to compile.
Design Mode is unable to display the document styles, skins, and images because the following assets have failed to compile:Details
:Unable to resolve resource bundle "components".( - Line:-1)
Unable to resolve resource bundle "skins".( - Line:-1)
Unable to resolve resource bundle "core".( - Line:-1)
Unable to resolve resource bundle "core".( - Line:-1)
Unable to resolve resource bundle "effects".( - Line:-1)
Unable to resolve resource bundle "layout".( - Line:-1)
Unable to resolve resource bundle "styles".( - Line:-1)
Unable to resolve resource bundle "components".( - Line:-1)
Unable to resolve resource bundle "core".( - Line:-1)
Any ideas?

I thought I had it by deleting a namespace reference; things started to render and all was good for a couple minutes. Then it reverted to the same problem so I'm open to other suggestions.

SOLVED : Lenovo X60 spontaneous sleep mode problem.

The problem is the flat panel screen! (either t-conn board and/or backlight). Viewiz HV121X03-100 Part No. 42T0359 FRU No. 13N7205. LCD : Wistron P/N:60.4Q443.001
I have 2 identical of Lenovo X60 laptops, with swivel-type-hinge at center. One has this spontaneous sleeping mode problem. I thought it was the Inverter problem - WRONG. Next some say it's the motherboard, CPU fan & heatsink, BIOS updates wrong also. All of these assumptions and theories are wrong diagnosed.
Solution replace the flat panel screen (very expensive because it has Wacom digitizer glass on top of the screen and board at the bottom.)
Roan
Computer Technician
Chapel Hill, NC

Hello @Tilia,
I have read your post on how your notebook computer is experiencing an issue with waking up from sleep mode, and I would be happy to assist you in this matter!
To further diagnose this issue, I recommend following the steps in this document on Troubleshooting sleep and hibernate issues in Windows 8. This should help configure your power management settings to effectively use sleep mode on your system.
Additionally, you can also restore your notebook's default power schemes by following the steps below:
Step 1. Click the Start button
Step 2. In the search box, type "Command Prompt"
Step 3. Right-click Command Prompt
Step 4. Click Run as administrator
Step 5. At the command prompt, type powercfg /restoredefaultschemes and press Enter
reference: http://superuser.com/questions/669571/windows-8-1-64-bit-power-schemes-gone
Please re-post with the results of your troubleshooting, and I look forward to your reply!
Regards
MechPilot
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

SWC Load Error - Design Mode Problem

Hi,
I'm loading custom .swcs into my Flash Builder (4.5 Burrito) project and I get these errors. These will only appear in design mode (not in source mode) and will not be labelled under the Problems tab, rather the Design Mode Problems tab:
SWC Load Error
SWC file failed to load. Any component dependent on this SWC file will not be displayed in the Design Mode.
The SWC may have failed to load because of:
* Incompatible definitions caused by usage of a different SDK version
* Missing referred class definitions
I don't think this problem is caused by an SDK incompatibility, as all these swcs have been created under flex 4 and I'm pretty sure under the 4.5 SDK.
Loading the components contained in these swcs onto my canvas (at design time) will work fine. I'm able to build and run the application without any errors caught by flash builder.
Any idea how to fix this problem, or what it means?

SWC Load error indicates that the swc used does not match with the definitions present in design view or with what is present in already loaded other lirbaries. The issue is reported by the flash loader. It looks like that, your swc is compiled with a previous version of the sdk and the design view and the related definition correpsonds to another version.
The incompatability logic is not in DV. When DV tries to load all the swc details available in the project, the loading fails as the loader reports the issue. There is hardly anything, we can do here from DV. If the player reports the incompatability issue, the loader is corrupted and all further loading is ignored. So to avoid such issue, DV ignores the failed swc's and tries to proceed.
If you pass me the swc , I can give the details of the incompatability. Ideally between 4.5 and 4.5.1 there should not have been any incompatability. However your case shows there is. You can contact me at [email protected]

MSI A75MA-P35 (MS 7697) With AMD ATHLON II QUADCORE - Several Beeps

Hi,
I´ve just monted an MSI A75MA-P35 (MS 7697) with a AMD ATHLON II QUADCORE (2.6), and at this time i´ve several beep codes (1 long + 2 shorts).
I´m using AMD Memory (1 slot, 4 Gb, pc3 - 12800 1600mhz, CL9 - 1.5V), that´s all i´ve connected/mounted.
ps - i´m using an Advance Power Supply with 480W.
Any ideas about this?
Regards,

Quote from: Svet on 04-April-12, 00:15:40
what's the exact CPU model?
PSU details?
VGA used?
memory details? brand, vendor, ECC?
And...? Does the system boots and works fine?
CPU - AMD ATHLON II X4 631 AD631XWNGXBOX
PSU - ADVANCE 5100S - 480W
VGA - ONBOARD
MEMORY - AMD MEMORY (1 slot, 4 Gb, pc3 - 12800 1600mhz, CL9 - 1.5V) AE34G1609U2
... and doesn´t boot at all.

MSI A75MA-P35 DDR3-1866 support?

Hi,
I'm interested in an A75MA-P35. Unfortunately, the website and manual say it only supports DDR3-1600 whereas the "little brother" (A55MA-P35) and basicly all other mainboards with FM1 support DDR3-1866.
Is this a mistake or does the A75MA-P35 really not support DDR3-1866?
Thanks in advance!

Quote from: Mark on 01-October-11, 06:20:53
The memory controller is built into the CPU so that determines what speed RAM is supported.
Now that you mention it, it's pretty obvious. Guess I'm getting too old for this stuff.

A75MA-P35 & Panel Audio Connector Help

Can anyone help me with these front panel connectors on my friend old case, all the cases i've ever done had block connectors that just fitted on the pin header but this has the connectors separate. The case connectors are the following.
Speaker R
Return L
Return R
Mic Bias
Speaker L
Mic In
Gnd
And the new A75MA-P35 motherboard is the following
Where do the case pins go on this pic above.

http://www.intel.com/support/motherboards/desktop/sb/CS-015851.htm
Edited:
Went to the website and verified:
1- Mic
2 - Ground
3 - Mic Bias
5 - Rt HP
6 - Rt Return
9 - Lt HP
10 - Rt Return

P35 Platinum rebooting problem

Hello,
I have just registered at MSI Forums, as i have quite strange problem with my PC and i need help :azn:
My specs:
Motherboard : MSI P35 Platinum, bios ver1.9
CPU : Intel Core 2 Duo e6600 coolde with Thermalright Ultra 120a + Zalman 120mm fan
Memory: Mushkin XP2-6400 2 GB CL4-4-3-10
VGA : Inno3D 8800gts 512 with Accelero s2 rev2 + 2 Silverstone 90mm fans
HDD : Seagate 160GB SATA
Optical : Liteon DVDRW LDW-851S
PSU : Tagan TG430-U22 (i am running it at 'combined rails' mode, which has 28A rating for the 12v rail-information from the sticker)
I also have 3 120mm fans mounted in case
I have Windows XP SP2 installed
I took attempt to overclock my cpu and memory, and i managed to get 3.4ghz for cpu and 972mhz for memory (486FSB ; CPU Multipliter 7 ; RAM timings 5,5,5,15 ; RAM voltage 2,0v ; CPU voltage 1.4125v ; VTT FSB voltage AUTO ; NB voltage 1.45v ; SB I/O power 1.8v ; SB core power 1.15v), i am able to run Orthos Blend test (stressing cpu and memory) for about 8 hours (so it's pretty stable I think)
So, let's get to the point:
I am able to run my PC flawlessly all day long, but when i try to turn it on next day, it keeps rebooting itself for few minutes (it turns for about 10 seconds but the screen stays black, then it turns off and turns on again.....LEDS keep showing red/red/green/red indicating memory problem) and finally boots with 'overclocking failed' information.............i get to the bios, change ABSOLUTELY NOTHING, save settings (or not save..it doesn't matter at all) and then it boots and loads Windows no problem.......... what the heck is wrong?? Is it memory problem? Or maybe PSU? (I was using it in my previous PC)
Any suggestions ? :azn:
Thanks in advance

Avoid that one, instead go for:
Quote from: Frankenputer on 20-September-08, 02:03:41
I would recommend the Corsair VX550 or TX650.
or 750TX

Lock records when in Update Mode / problem with 2 users on 1 document

Hi,
when user A updates e.g. a purchase order and user B goes into this purchase order and updates e.g. the remark before user A, then user A cannot save his changes. Imagine user A has put in several new lines and has made several price adjustments, his work will be gone.
In most cases this should not happen very often, but it could. Since B1 recognizes when another user has updated the document before, it should be possible to solve this situation more convenient (either by lock, saving to a new document, comparing to the old version, etc).
Thank you
Sebastian

Hi Sebastian,
Your request is understandable. It may not have big problem to change current process by coding. However to lock records whenever in update mode, that could create too many locks. It is basically not good for performance. The trade off may be allowing save as function. However, this may not be a desirable solution for most end users.
Thanks,
Gordon

K9N PLATINUM(NON SLI) DUAL CHANNEL MODE PROBLEM

hi
put a new system together with the following specs:
amd am2 3800+(2ghz)
k9n platinum 1.20 bios
2x512 kingston ddr2(667mhz)
pci video(yes not pci-e)have not decided which vid card to get yet.
500w psu 12v 35a,5v 25a,3.3v 25a
liteon dvd burner
seagate 300gb ide 7200/16 meg cache windows xp-pro sp2 with all updates.
not overclocking or even trying to.
no sata drives connected.
has never failed to post,boot windows and no lockups or blue screens.
ok,i am trying to get the memory to work in dual mode.
everytime i put the memory in the dual mode slots,the cpu clocks down to 1ghz instead of 2ghz.
verified by bios,windows and cpu-id
i have tried different memory(both ddr2 533 and 667)667 installed now.
also never had any install problems with windows and everything runs fine until i tried dual mode.
after the cpu clocks down to 1ghz,the only way to get it back to normal is a bios reset( load defaults
or press red button).
if i leave the memory as single channel then i have no issues.
also cpu-id says the chipset for my board is nforce 550,i thought k9n platinum had 570 nforce chipset?
this might just be a problem with cpu-id though.
any thoughts on the cpu down clock problem in dual channel mode?
thanks,jeff

1 assume you can get into BIOS with 1 stick only?
Go into the BIOS and manually set the timings and voltage to what your memory manufacturer recommends. Use a 2T command rate and see if it works.
Try both "sets" of dual channel slots, i.e. the two left slots or the two right slots.

A75MA-P35 C6 Mode Problem

Similar Messages

Maybe you are looking for