A7V133 reboot during installation :-(

Dear,
During installation my A7V133 with 3C905-C an NVIDIA TNT 64 reboots before installation
even starts. I could not read the printed message since the reboot proces is to fast.
All my devices are in the supported list Solaris 8 10/01.
Has anyone an explanation for this ?
Could this have somthing to do with the PCI interrupt charing ?
Hoping to receive some positive advice, I meanwhile remain,
P. Pelgrims
P.S. Installing Solaris 8 10/1 on VMWARE for Linux works fine but VMWARE emutates
and virtual networkcard and could offer only 640x480 Xterm !

Hi Pelgrims,
May be problem with PCI interrupts sharing violation with your 3Com NIC card and TNT VGA card. So remove your NIC card from your system and try to do Solaris installation.
Hope it helps.
Senthilkumar
Developer Technical Support
Sun Microsystems, Inc.
http://www.sun.com/developers/support

Similar Messages

HD not recognized after reboot during installation

Hello,
I am installing Solaris 8 on a Dell Optiplex pc.
I boot from the CD Rom and the install appears to go ok until the install program indicates that it has to reboot.
When the unit does reboot, I get an error message that it cannot find the hard drive.
When I go to the bios setting, I see that it only recognizes the floppy drive as a means to boot.
What have I done wrong?
I have a dos partition on the drive (8mb and formatted).
Chris Hax

I am new to solaris too, but according to the information I gathered here and there, it needs an unformatted primary partition (just white space). I am dual booting with Windows NT, and what I did was to create small partition for the boot partition of the NT and leave the rest of the disk empty(do not create partition). Somewhere during the installation, solaris will ask you,among other things, whether it can use the empty space without disturbing the existing data. Answer yes and it will ceate it's own boot selection, whereby you will be able to select between solaris and anything else that you had before. That's a superb feature in solaris.
regards.
Yousef

Unable to reinstall MacOS - reboots during installation

I've got a Late 2009 iMac 27".
It's been getting more and more unstable until its properly unusable.
Mostly kernal panics, but even things like Finder crashing every 5 seconds.
After reading lots of discussions, I thought it sounded like a broken hard disk.
I took it into an apple authorised repair shop. Their diagnostics showed a software fault rather than a hardware fault.
They suggested I re-install MacOS - something I did about 12 months ago and it did seem to make it more reliable.
In recovery mode, I first deleted the partition.
However during the re-install, it starts downloading Mountain Lion and after a while (variable, but approx 30 mins) it reboots and starts recovery mode again.
Any clues?
Help appreciated.

Let's add the printer manually:
1. Click "Start" button --> Printers and Faxes.
2. Under Printer Tasks, click "Add Printer".
3. Click "Next" button on the Add Printer Wizard window.
4. Select "Local printer attached to this computer". Deselect "Automatically detect and install My Plug and play printer". Click "Next".
5. Under Select a Printer Port option, select "Create a new port" and select "Standard TCP/IP Port" and click "Next" button.
6. In the "Welcome to the Add Standard TCP/IP printer port wizard" make sure that the printer is turned on and connected to same network that your computer is connected to. Click "Next" button.
7. Under "Add Standard TCP/IP Printer Port" enter the printer's IP address. Click "Next" then click "Finish".
8. Now, select HP from the list of manufacturers, select your printer from the list of Printer models and click 'Next' button.
9. If you can't find your printer, you'll need to find the install CD and use the "Have Disk" option to select one of the hp*.ini files. Alternatively, you can select another HP printer model from the same type.
10. Add the print spooler name and click "Next".
11. Click "Next"
12. Click "Next" and then "Finish"
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

UNEXPECTED REBOOT DURING INSTALLATION

I just installed 3COM-3C905C-TX NIC on my compaq intel machine with win95 before I install SOLARIS 8 on it. This NIC is compatible with SOLARIS 8 Hardware Compatible List as specified for network connectivity. The system booted properly until when it got to the stage where the network is to be configured. Suddenly all I see was REBOOT at the bottom of my screen and the process started all over again from the begining.
PLEASE I REALLY NEED YOUR ADVISE AND HELP. I have been struggling with this all day without success.
Thanks,
kbolar.

Hi,
The problem may be due to the system was unable to trace your network card and so it reboots. Check out the connectivity of the network card or do a diagnostic test.
Hope it helps!
Regards,
Dharani
SlashSupport India Pvt Ltd.
I just installed 3COM-3C905C-TX NIC on my compaq intel
machine with win95 before I install SOLARIS 8 on it.
This NIC is compatible with SOLARIS 8 Hardware
Compatible List as specified for network connectivity.
The system booted properly until when it got to the
stage where the network is to be configured. Suddenly
all I see was REBOOT at the bottom of my screen and
the process started all over again from the begining.
PLEASE I REALLY NEED YOUR ADVISE AND HELP. I have been
struggling with this all day without success.
Thanks,
kbolar.

Windows 2k adv svr hang/reboot during installation

Hi all,
I am trying to install the latest ver of Directory Server 5.2 on IBM x345 (dual Xeon 3 GHz) with windows adv server ... but unfortunately the machine always hang with blue screen and memory dump :( ... I tried this on two different servers .. but still the same !!!
note: both machines are Domain controller

Hi Joey!
I have the same problem with the same hardware. Did you resolve this problem? If yes, how did you resolve the problem?
Thanks,
Arturo.

Reboot during lion installation

Hi @all,
i've downloaded lion from the App-Store.
After the download the installer startet automaticly and reboot the System.
The problem is, that the installer starts after the first reboot and failed with no error and shutdown the system.
After restart the MacBook Pro, the system reboots during the installation anymore,
what can i do ?
thx
forti

http://www.apple.com/support/mac/app-store/contact.html?form=account

I upgraded my iPad to version 5.0, I had a message on my Setting to upgrade the software to version 5.0.1, I select install and during installation my iPad2 star rebooting and now doing it non stop. I have no time to restore or do anything

Hi, I upgraded my iPad to version 5.0, I had a message on my Setting to upgrade the software to version 5.0.1, I select install and during installation my iPad2 star rebooting and now doing it non stop. I have no time to restore or do anything. My ipad rebooting every 2 or three minutes

See Here
iPad Unable to Update or Restore
http://support.apple.com/kb/ht4097

Reboot fails OS X 10.6.7 mac "error occurred during installation"

Macbook pro wont install OS X 10.6.7 "error occurred during installation"

Try this:
Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
Now try reinstalling the 10.6.7 update. Be sure you are using the Combo Updater.

Updated itunes, error message about mobile popped up during installation, then after installation, tunes will not start. gives error that a dll file is missing.

I downloaded the new Itunes version. During installation, there was an error message that said no Mobile access. After installation, Itunes would not open. Gave an error message that a DLL file was not found. Removed itunes from computer and initiated new download. Same problem with new download. Still does not open. I'm stumped. I have over 30,000 files in itunes and use it every day HELP

Go to Control Panel > Add or Remove Programs (Win XP) or Programs and Features (later)
Remove all of these items in the following order:
iTunes
Apple Software Update
Apple Mobile Device Support (if this won't uninstall move on to the next item)
Bonjour
Apple Application Support
Reboot, download iTunes, then reinstall, either using an account with administrative rights, or right-clicking the downloaded installer and selecting Run as Administrator.
The uninstall and reinstall process will preserve your iTunes library and settings, but ideally you would back up the library and your other important personal documents and data on a regular basis. See this user tip for a suggested technique.
Please note:
Some users may need to follow all the steps in whichever of the following support documents applies to their system. These include some additional manual file and folder deletions not mentioned above.
HT1925: Removing and Reinstalling iTunes for Windows XP
HT1923: Removing and reinstalling iTunes for Windows Vista, Windows 7, or Windows 8
tt2

There was a problem during installation of blackberry messenger. Please try again

There was a problem during installation of blackberry messenger ( any application). Please try again, this is the message i get anytime i try to download or upgrade any application on my blackberry bold 9870. pls i need your help
Thanks
bellokeshi

bellokeshi wrote:
Blackberry appworld version: 4.0.0.63
OK, that is almost the latest version... .65 is later.
You can upgrade your AppWorld from using your BlackBerry browser to go to www.blackberry.com/appworld
After you upgrade, Do a simple reboot on the BlackBerry in this manner: With the BlackBerry device POWERED ON, remove the battery for a minute, and then reinsert the battery to reboot.
IF then you don't see or can't find the AppWorld icon, please post back here.
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Errors encountered during installation(7)

When trying to install lightroom through creative cloud I get Installation Failed - Errors encountered during installation(7) - I have tried rebooting the machine logging in and out nothing helps ?

Hello all and thank you for the replies. @Mylenium this is a new system setup = windows 8.1 fully updated - hardware not so new but more that adequate - i7 processor 3.2Mhz 16GB ram 2TB hdd 2 x Nvidia GTX 60's in SLi and Adobe apps was the first I installed , Bridge & Photoshop went through fine. The only error message was that one clicking the link to get more info just took me to a generic help site.
Anyway last night I downloaded the trial version which came down fine and installed it without a glitch and after registering the software online it picked up that I was a CC user and automatically entered the license key so all is good.

Errors occurred during installation, install failed.

So recently I got into a bit of trouble when my web browsers got hacked and started installing some adware on my computer... I'm still getting that sorted out, but I think while I was going through my "Common Files" folder and deleting things that looked suspicious, I accidentally deleted some kind of file for Apple's many programs that install with iTunes. I realized my mistake when, at the next reboot, Windows gave me an error that some program could not start due to a missing .dll file and then gave me the program name, which as it turns out was Apple Application Support. I uninstalled the support program to attempt to correct the issue, but when I did it only broke things further! iTunes claimed that it could not work without the support software, so I tried uninstalling and reinstalling iTunes to get the Application Support program back. Sadly, this did not work either as iTunes did not uninstall correctly, freezing windows explorer. Then when I downloaded the install file to try again, it gives me an error almost immediately saying "Errors occurred during installation, your system has not been modified. Run the installer again." (I'm paraphrasing) When I run it again, the same thing happens.
In conclusion, it appears that by deleting one simple file, I have broken iTunes permanently and I can no longer use it on my computer. Ugh. Can anyone help me get it back? I can't believe I'm even asking this... I'm not really an apple fan but I do use it to put videos and stuff on my iPad and I have a bunch of playlists in there that I've spent time organizing, so I still use it as my "main" mp3 player. This is very inconveinent!

Windows gave me an error that some program could not start due to a missing .dll file and then gave me the program name, which as it turns out was Apple Application Support. I uninstalled the support program to attempt to correct the issue,
Let's try a standalone Apple Application Support install. It still might not install, but fingers crossed any error messages will give us a better idea of the underlying cause of the issue.
Download and save a copy of the iTunesSetup.exe (or iTunes64setup.exe) installer file to your hard drive:
http://www.apple.com/itunes/download/
Download and install the free trial version of WinRAR:
http://www.rarlab.com/
Right-click the iTunesSetup.exe (or iTunes64Setup.exe), and select "Extract to iTunesSetup" (or "Extract to iTunes64Setup"). WinRAR will expand the contents of the file into a folder called "iTunesSetup" (or "iTunes64Setup").
Go into the folder and doubleclick the AppleApplicationSupport.msi to do a standalone AAS install.
Does it install properly for you?
If instead you get an error message during the install, let us know what it says. (Precise text, please.)

PhotoSmart C6280 - Fatal Error During Installation

I have Win 7 (64 bit) system and cannot install software for my C6280 All-In-One Printer. I keep getting a "Fatal Error During Installation" message and then the software tries to uninstall. During this process a reboot is required and then the software tries to install again and then fails. I'm in a never ending circle of install-uninstall-install-uninstall........
How do I get out of this? I want to completely uninstall all software associated with this printer and then start from the beginning.
The issue that brought about this situation was that I was getting the following message at bootup time:
"There was a problem starting C:\users\Myron\AppData\Local\IsolatedStorage\HP\zelqof.dll
The specified module could not be found."
I am assuming that the missing module would get installed if I re-install all of the associated software with the printer as this is the ONLY printer connected (USB) to this PC.
This question was solved.
View Solution.

Hello BigDog5280,
Welcome to the HP Forums.
I see that you are having an issue with a looping uninstall/reinstall of the software and drivers.
If you have Norton 360 installed, please disable it and reboot the computer. When the computer is back on, attempt to reinstall with Norton 360 still disabled.
Here is a link to a document that deals with a Fatal Error 'Error 1603. A fatal error occurred during installation' (MSI Error 1603) Displays Durin...
If the troubleshooting does not help resolve your issue, I would then suggest calling HP's Technical Support to see about further options for you. If you are calling within North America, the number is 1-800-474-6836 and for all other regions, click here: click here.
Thanks for your time.
Click the “Kudos Thumbs Up" at the bottom of this post to say “Thanks” for helping!
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
W a t e r b o y 71
I work on behalf of HP

"An error occurred during installation" OS X Lion

I downloaded Lion from the Mac App Store - download went fine. After the installer rebooted and the actual installation began, I keep getting a message stating "An error occurred during installation" at the "About 28 minutes" time. No clue what to do here, so any help would be GREATLY appreciated. I have a new model MacBook running Snow Leopard.

GPCY wrote:
I only found disk 1: Mac OS X installed ESD, and
Disk 2: Mac OS X base system.
Which one I should click?
So you did hold Command option r and booted, not just Command r?
You saw a globe turning as Internet Recovery loaded from Apple's servers?
You need to connected to the Internet to load this from Apple, either by Ethernet cable or using the Wifi connection.
Quit and launch Terminal from the menu and type in this command and press enter, then type the results here
diskutil list
It should look like something like this
HummerMacs-MacBook-Pro:~ hummermacjr$ diskutil list
/dev/disk0
   #:                       TYPE NAME                    SIZE       IDENTIFIER
   0:      GUID_partition_scheme                        *750.2 GB   disk0
   1:                        EFI                         209.7 MB   disk0s1
   2:                  Apple_HFS Macintosh HD            374.9 GB   disk0s2
   3:                  Apple_HFS Macintosh HD 2          374.8 GB   disk0s3

ZenAgent Reboots During Imaging After Upgrade

Went from 11.2.3a > 11.3 > 11.3.1 > 11.3.1 FRU1
Zenworks is rebooting during application installs during imaging now. Here is the message: "Your system is being restarted to finish applying the Zenworks configuration changes that have occurred."
I found this article, but it doesn't apply to this version: https://www.novell.com/support/kb/doc.php?id=7009609
How can I prevent the restart from happening?

Nzorn,
then I'd say it would be worth opening a Support incident with us at ENGL, then I can take a look at the logs... if it turns out to be a Novell issue, then we can bring the conversation back here...
I'd want a debug zim.log https://www.engl.co.uk/kb/tid-2006018.htm and possiblt with the imaging codes as well https://www.engl.co.uk/kb/tid-2011007.htm
Shaun Pond
newly reminted as a Knowledge Professional

A7V133 reboot during installation :-(

Similar Messages

Maybe you are looking for