Aaa console telnet via radius

Using this configuration to radius control console and telnet access :aaa authentication login default group Sts-radius local
aaa authorization exec default group Sts-radius local
aaa accounting exec default start-stop group Sts-radius
In wlse I've configured :
diagonale@Sts-radius:aaa-server user
aaa-server user diagonale password <encrypted>
aaa-server user xxx password <encrypted>
attributes =
cisco-avpair = shell:priv-lvl=15
service-type = login
The resultat:
user fr231662 can log via console or telnet as required.
user diagonale cannot connect via telnet as required, but CAN connect via console.
I wish to NOT allow diagonale to connect via console.
How can I do that ??
Thanks

Hello,
what does the configuration of con 0 look like ? In order for RADIUS (or the local database as the backup) to authenticate console access, the config should be (here, a specific list named CONSOLE is used, in order to distinguish that this is for console access):
aaa authentication login CONSOLE group Sts-radius local
line con 0
password cisco
login authentication CONSOLE
Regards,
GNT

Similar Messages

Telnet via console port

Hi
Is it possible to telnet via console port to a server without any additional hardware? I understand that an ip needs to be configured but i am not sure how it is to be done.
any help given is appreciated..
thanks

Yes , you can but your server must see server that you want to access first
first you can ping to server that you want to access . if you can't see it ,that is impossible to access it .

Cisco 1602i + Authenticating users via RADIUS?

               Hello,
Our company recently purchased a Cisco 1602i standalone WAP to replace the WAP4410Ns that we were having issues with. I am now attempting to configure the RADIUS authentication, as we have a User network and a Guest connection. The Guest connection works fine, using WPA PSK. However, I can't seem to get the RADIUS authentication to work. Reading the documentation has got me a little confused, and I have tried turning on debugging (debug radius authentication, debug aaa) but those show nothing. Also, in the RADIUS server itself (Windows 2008 R2 NPS), I see nothing in the logs when I try to connect using a device or the "test aaa" command. Can someone guide me on what I'm doing wrong? I followed someone's advice on another forum and removed "authentication network-eap" from the SSID (phoenix_2), and now when I attempt to connect with a device it just asks me for a password, it doesn't prompt for a username anymore. I am very stumped. Here's the relevant config:
aaa new-model
aaa group server radius rad_eap
server 10.200.5.24
aaa group server radius rad_mac
aaa group server radius rad_acct
aaa group server radius rad_admin
aaa group server tacacs+ tac_admin
aaa group server radius rad_pmip
aaa group server radius dummy
aaa authentication login eap_methods group rad_eap
aaa authentication login mac_methods local
aaa authorization exec default local
aaa accounting network acct_methods start-stop group rad_acct
aaa session-id common
clock timezone EST -5 0
ip cef
ip domain name gst
dot11 syslog
dot11 vlan-name guest vlan 255
dot11 vlan-name user vlan 140
dot11 ssid phoenix_2
   vlan 140
   band-select
   authentication open eap eap_methods
   mbssid guest-mode
dot11 ssid walker_2
   vlan 255
   band-select
   authentication open
   authentication key-management wpa version 2
   mbssid guest-mode
   wpa-psk ascii 7 0353035E535879191B
interface BVI1
ip address 10.200.5.70 255.255.255.0
ip default-gateway 10.200.5.1
ip forward-protocol nd
no ip http server
ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
ip route 0.0.0.0 0.0.0.0 10.200.140.1
ip route 0.0.0.0 0.0.0.0 10.200.5.1
ip radius source-interface BVI1
access-list 111 permit tcp any any neq telnet
snmp-server community G!0bal RO
radius-server attribute 32 include-in-access-req format %h
radius-server host 10.200.5.24 key 7 01445E510E1C07032A495C0D0B0C011718190D3E2E767863
radius-server vsa send accounting
The NPS worked just fine with the WAP4410Ns, not sure why we're having so much trouble with the 1602i.

Thanks Rasika, your link worked. I had the authentication key before, but i removed it while I was trying different things. My main issue was not applying the list name to the ssid, the documentation did not make it clear that when the radius server is specified using the "radius-server ...." command, that the radius group refers to that command when you configure the group. Once that clicked, it made sense that the method list name was specifed by the radius group, and that the authentication methods then referred to the radius group. It was a big question mark in my head how the radius server was applied to the SSID prior to reading your post.
I haven't tried the "erase startup-config" command yet, I will try that next.
Quick question, why are both authentication open and authentication network-eap needed? I would assume authentication network-eap would suffice, unless the authentication open command refers to the allowed devices and not just authentication via RADIUS?

Authentication via RADIUS : MSCHAPv2 Error 691

Hello All,
I am working on setting up authentication into an Acme Packet Net-Net 3820 (SBC) via RADIUS. The accounting side of things is working just fine with no issues. The authentication side of things is another matter. I can see from a packet capture that the access-request
messages are in fact getting to the RADIUS server at which point the RADIUS server starts communicating with the domain controllers. I then see the chain of communication going back to the RADIUS and then finally back to the SBC. The problem is the response
I get back is always an access-reject message with a reason code of 16 (Authentication failed due to a user credentials mismatch. Either the user name provided does not match an existing user account or the password was incorrect). This is confirmed by looking
at the security event logs where I can see events 4625 and 6273. See the events below (Note: The names and IPs have been changed to protect the innocent):
Event ID: 6273
Network Policy Server denied access to a user.
Contact the Network Policy Server administrator for more information.
User:
Security ID:
NULL SID
Account Name:
real_username
Account Domain:
real_domain
Fully Qualified Account Name:
real_domain\real_username
Client Machine:
Security ID:
NULL SID
Account Name:
Fully Qualified Account Name:
OS-Version:
Called Station Identifier:
Calling Station Identifier:
NAS:
NAS IPv4 Address:
10.0.0.10
NAS IPv6 Address:
NAS Identifier:
radius1.real_domain
NAS Port-Type:
NAS Port:
101451540
RADIUS Client:
Client Friendly Name:
sbc1mgmt
Client IP Address:
10.0.0.10
Authentication Details:
Connection Request Policy Name:
SBC Authentication
Network Policy Name:
Authentication Provider:
Windows
Authentication Server:
RADIUS1.real_domain
Authentication Type:
MS-CHAPv2
EAP Type:
Account Session Identifier:
Logging Results:
Accounting information was written to the SQL data store and the local log file.
Reason Code:
16
Reason:
Authentication failed due to a user credentials mismatch. Either the user name provided does not map to an existing user account or the password was incorrect.
Event ID: 4625
An account failed to log on.
Subject:
Security ID:
SYSTEM
Account Name:
RADIUS1$
Account Domain:
REAL_DOMAIN
Logon ID:
0x3E7
Logon Type: 3
Account For Which Logon Failed:
Security ID:
NULL SID
Account Name:
real_username
Account Domain:
REAL_DOMAIN
Failure Information:
Failure Reason:
Unknown user name or bad password.
Status:
0xC000006D
Sub Status:
0xC000006A
Process Information:
Caller Process ID:
0x2cc
Caller Process Name:
C:\Windows\System32\svchost.exe
Network Information:
Workstation Name:
Source Network Address:
Source Port:
Detailed Authentication Information:
Logon Process:
IAS
Authentication Package:
MICROSOFT_AUTHENTICATION_PACKAGE_V1_0
Transited Services:
Package Name (NTLM only):
Key Length:
0
This event is generated when a logon request fails. It is generated on the computer where access was attempted.
The Subject fields indicate the account on the local system which requested the logon. This is most commonly a service such as the Server service, or a local process such as Winlogon.exe or Services.exe.
The Logon Type field indicates the kind of logon that was requested. The most common types are 2 (interactive) and 3 (network).
The Process Information fields indicate which account and process on the system requested the logon.
The Network Information fields indicate where a remote logon request originated. Workstation name is not always available and may be left blank in some cases.
The authentication information fields provide detailed information about this specific logon request.
- Transited services indicate which intermediate services have participated in this logon request.
- Package name indicates which sub-protocol was used among the NTLM protocols.
- Key length indicates the length of the generated session key. This will be 0 if no session key was requested.
So at first glance it would seem that the issue is merely a case of an invalid username or mismatched password. This is further confirmed in the packet capture where I can see the MSCHAPv2 response has an error code of 691 (Access denied because username or
password, or both, are not valid on the domain). The thing is I know I am using a valid username and I have tried many usernames including new ones I created just for troubleshooting. I don't know how many times I have reset the password in an attempt to ensure
it is not a mismatch password. I have even made sure to use passwords that are fairly short and contain only letters to ensure there was no terminal encoding issues (we connect to the SBC via SSH clients). I have also done this same thing with the shared secret
used during communication between the SBC and the RADIUS server. I have tried prefixing the username with the domain name at login (though I don't think that should be necessary). I have also tried using the full UPN of the user to login. I have tried several
RADIUS testing clients (NTRadPing, RadiusTest, etc.), but they either don't support MSCHAPv2 or only support EAP-MSCHAPv2. I have even created my own client using PHP's PECL RADIUS module. Still it always seems to fail with the MSCHAPv2 authentication with
an error code of 691. Does anyone have any ideas as to why I always get an invalid username or bad password response when I have done everything possible to ensure that is not the case?
Here are the specs for our RADIUS configuration:
Windows Server 2012 R2
SQL Server 2012 Back End Database for accounting.
The server has been authorized on the domain and is a member of the "RAS and IAS Servers" group. For which that group does have access to the accounts we are testing with.
The accounts we are testing with do have the "Control access through NPS Network Policy" option checked under their "Dial-in" property tab.
RADIUS clients configured to simply match on the IP address which you can see from the events above that it is applying the client friendly name.
Connection Request Policy: The "SBC Authenication" policy is being applied as seen above. The only condition is a regex expression that does successfully match the friendly name.
Network Policy: As seen in events above, none are getting applied. For troubleshooting purposes I have created a Network Policy that is set to "1" for the processing order and its only condition is a Day and Time Restriction currently set to any
time, any day.
The authentication method is set to only MSCHAPv2 or MSCHAPv2 (User can change password after it has expired). I have tried adding this to just the Network Policy and I have also tried adding this to the Connection Request Policy and setting it to override
the authentication method of the Network Policy.
We do have other RADIUS servers in our domain that use PEAP to authenticate wireless clients and they all work fine. However, we need this to work with MSCHAPv2 only (No EAP).
All other configurations are set to the defaults.
The only other things of note to consider is the fact that in the events above you can see that the Security ID is "NULL SID". Now I know this is common especially among failed logons but given that this issue is stating an invalid username or
bad password, perhaps it matters in this case. Also, this server has been rebuilt using the same computer account in Active Directory. I do not know if it would have worked before the rebuild. Essentially we built this server and only got as far as authorizing
the server to the domain and adding SQL when we decided to separate out the SQL role onto another server. Rather than uninstalling SQL we just rebuilt the machine. However, before reinstalling Windows I did do a reset on the computer account. I don't think
this should matter but thought I would point it out if there is some weird quirk where reusing the same SID of a previously authorized NPS server would cause an issue.
All in all it is a fairly basic setup and hopefully I have provided enough information for someone to get an idea of what might be going on. I hope this was the right forum to post this too, I figured there would be a higher number of RADIUS experts here than
any of the other categories. Apologies if my understanding of this seems a bit basic, after all, when it comes to RADIUS servers I guess you could say I'm the new guy here.

Update 1:
In an attempt to further troubleshoot this issue I have tried bringing up additional servers for testing. Here are the additional tests I have performed.
Multiple Domains
I have now tried this in 3 different isolated domains. Both our test and production domains as well as my private home domain which has very little in the way of customizations aside from the modifications made for Exchange and ConfigMgr. All have the same
results described above.
VPN Service
Using Windows Server 2012 R2 we brought up a separate server to run a standard VPN setup. The intent was to see if we could use RADIUS authentication with the VPN and if that worked we would know the issue is with the SBCs. However, before we could even
configure it to use RADIUS we just attempted to make sure it worked with standard Windows Authentication on the local VPN server. Interestingly, it too fails with the same events getting logged as the RADIUS servers. The client machine being a Windows 8.1
workstation. Again I point out that we have working RADIUS servers used specifically for our wireless environment. The only difference between those RADIUS servers and the ones I am having problems with is that the working wireless servers are using PEAP instead
of MSCHAPv2.
FreeRADIUS
Now I'm no Linux guru but I believe I have it up and running. I am able to use ntlm_auth to authenticate users when logged on to the console. However, when the radiusd service tries to use ntlm_auth to do essentially the same thing it fails and returns the
same message I've been getting with the Windows server (E=691). I have the radiusd service running in debug mode so I can see more of what is going on. I can post the debug info I am getting if requested. The lines I am seeing of particular interest however
are as follows:
(1) ERROR: mschap : Program returned code (1) and output 'Logon failure (0xc000006d)'
(1) mschap : External script failed.
(1) ERROR: mschap : External script says: Logon Failure (0xc000006d)
(1) ERROR: mschap : MS-CHAP2-Response is incorrect
The thing to note here is that while we are essentially still getting a "wrong password" message, the actual status code (0xc000006d) is slightly different than what I was getting on the Windows Servers which was (0xc000006a). From this document
you can see what these codes mean:
NTSTATUS values . The good thing about this FreeRADIUS server is that I can see all of the challenge responses when it is in debug mode. So if I can wrap my head around how a MSCHAPv2 response is computed I can compare it to see if this is simply a miscomputed
challenge response. Update: Was just noticing that the 6a code is just the sub-status code for the 6d code. So nothing different from the Windows Servers, I still wonder if there is a computation error with the challenge responses though.
Currently, I am working on bringing up a Windows Server 2008 R2 instance of a RADIUS server to see if that helps at all. However, I would be surprised if something with the service broke between W2K8 R2 and W2K12 R2 without anyone noticing until now. If this
doesn't work I may have to open a case with Microsoft. Update: Same results with W2K8 R2.

Cisco Prime Infrastructure 2.1 GUI authentication via RADIUS server (Cisco ISE 1.2 integrated with AD)

Hi,
I want to access Cisco PI 2.1 GUI using my AD credentials, so on PI I've enabled RADIUS AAA Mode and added RADIUS servers (two ISE nodes in our case). On ISE I added PI as RADIUS client and configured the same keys. Next, on ISE I created authorization profile PRIME_ADMIN_ACCESS with only attribute settings defined:
My authentication and authorization rules relating that case are as on following screenshots:
So when I open GUI of PI and enter my AD credentials to log in I have no success and I receive following message:
Looking in ISE's Authentication section I can see following:
Time difference between these two authentication/authorizations is just 25 msecs and clicking on each of them reveals following:
So at first I can authenticate and authorize (authorization profile has necessary attributes defined for PI management access (NCS:role0=Root, NCS:virtual-domain0=ROOT-DOMAIN)) and after 25 msecs I am getting failure. So what could be cause of such things and how I can successfully log in to PI GUI authenticating via ISE using AD credentials?

Hi,
-- Please Go to Administration > Logging > set the Message level to TRACE > Click save
-- Then try to add the ISE.
-- Once it fails, collect the logs from Administration > Logging >
check the "ncs-0-0.log" & search the file for "ERROR" & paste the results here. This will give us exact reason.
- Ashok
Please rate the post or mark as correct answer as it will help others looking for similar information

Anyconnect session accounting via radius or syslog ?

Hi
Does anyone have a deployed accounting method to log Anyconnect session details ? Do you do it via a radius server or via logging messages to a syslog server ?
If so could you assist with appropriate configuration ? I am looking to log successful and unsuccessful authentications as well as session length, log on and log off times.
I've been playing around with Anyconnect authenticating to AD via ACS 5.1 but can't seem to get the accounting details I require. Similarly I have tried to catch appropriate syslog messages but again without much success.
Many thanks for any input, St.

What all you have configured for radius accounting on ASA?
Can you paste the o/p of show run aaa-server and show run tunnel-group
Basically all you need to define radius server group and call that group under tunnel-group parameters.
!--- Configure the AAA Server group.
ciscoasa(config)# aaa-server RAD_SRV_GRP protocol RADIUS
ciscoasa(config-aaa-server-group)# exit
!--- Configure the AAA Server.
ciscoasa(config)# aaa-server RAD_SRV_GRP (inside) host 192.168.1.2
ciscoasa(config-aaa-server-host)# key secretkey
ciscoasa(config-aaa-server-host)# exit
!--- Configure the tunnel group to use the new AAA setup.
ciscoasa(config)# tunnel-group ExampleGroup1 general-attributes
ciscoasa(config)#accounting-server-group RAD_SRV_GRP.
Once done, you can then establish a session and check radius accounting detailed packet on ACS 5.x >> Monitoring and reports > catalog > aaa protocols > radius accounting.
In case you don't see radius accounting after following the above steps then please turn on the "debug aaa accouting and debug radius on ASA". This way we can check whether ASA is sending the accountinf session details to ACS or not.
Regards,
Jatin Katyal
- Do rate helpful posts -

Assign QoS Service Policy via RADIUS to Catalyst 45k/37k?

hi,
is there a way to assigen a QoS service policy via Radius to an Caltalyst 4500/3750 Switchport?
in detail, we would like to assign this policy
    policy-map SET_EF
     class class-default
       set dscp ef
to an interface. All traffic should be marked with a defined DSCP value.
This works find when doing it statically with
    interface FastEthernet2/1
         service-policy input SET_EF
but we would need to assign such a policy via Radius during the 802.1x Authentication. different users should get differnt policies. We use Cisco ACS 5.2 as Radius Server and there actually is a field for
that in the Authorization Profile Common Tasks Configuration. in detail, this uses the cisco-av-pair "sub-policy-In=<policy name>" attribute to assign a service policy to an NAS.
we found also two other attributes "sub-qos-policy-in" and "ip:sub-qos-polcy-in" for that. CCO says that "ip:sub-qos-polcy-in" works with Catalyst 65k (http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/ios/12.2SX/configuration/guide/qos.html#wp1926523)
unfortunately this seems to not work on Catalyst 45k and 37k.
In the ACS Logs we can see that these attributes are attached to the Radius Reply, but unfortunately they are ignored by the switch.
it is interesing that when entering "show aaa attributes" on the Catalyst 45k, these attributes are displayd - so for my understanding the switch should understand these attibutes (?)
    4503-E#sh aaa attributes
    AAA ATTRIBUTE LIST:
        Type=1     Name=disc-cause-ext                 Format=Enum
        Type=2     Name=Acct-Status-Type               Format=Enum
    <snip>
        Type=345   Name=sub-policy-In                  Format=String
        Type=346   Name=sub-qos-policy-in              Format=String
        Type=347   Name=sub-policy-Out                 Format=String
        Type=348   Name=sub-qos-policy-out             Format=String
any input is welcome :-))
best reagrds

additionally to this discussion, i've just opened a service request with TAC.
unfortunately the engineer told me that by now per-User QoS is definitely no supported on this two plattforms but it's listed on the roadmap and will be possibly availabe mid 2012......

WLC Management Admin via RADIUS

I am trying to have a management user authenticate via radius and have full admin privileges.
For a WCS I can simply set the radius attribute of "Cisco-AVPair.attr|Wireless-WCS:role0=Admin" and that user will get full admin rights. I found this doc to grant a user lobby admin:
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a0080871921.shtml
but, it is specific to the using the Cisco ACS as a radius server. What attributes do I need to set for a user to get full admin rights to a WLC when authenticating via radius? Thanks.

My problem: I have a local management user profile defined on my WLC and it works fine when the Priority Order is set to LOCAL. When I change the Priority Order to make RADIUS first and LOCAL second, I can't get logged into the WLC using CLI, GUI, or the console. The last time this happened I had to reset the WLC and start over. I don't want to do that again, so I need some way to get into the WLC.
Once I can get back into the WLI would prefer using Active Directory to authenticate the management user but that doesn't seem to work. My RADIUS acts as a front end for the Active Directory database and works well for many of our Cisco LAN switches andd Routers. Now I'm trying to set up the WLC to authenticate the management user with RADIUS. I have set the RADIUS (MS IAS) to return two attributes;
1. Vendor-Specific -Vendor Code 14179, Value=management
2. Service-Type - Value=Login
When I try to login using my AD account, the RADIUS server log shows an Access Request record, then an Access-Accept record that makes it appear RADIUS has successfully authenticated the user. But the login prompt for the GUI comes back as if it has failed. Same with the CLI login. Now I can't get logged into the WLC. How can I get into the box to manage it again?
Thanks

MAC Filtering via Radius not working

Hi Folks,
I'm having problems with MAC filtering via RADIUS. I have a combination of a local database on the controllers and remote MAC addresses provisioned on a Cisco ACS. My problem is that even when I've set the controllers to use Radius and I've configured the order to be local and then radius the controllers never sent an auth request to the Radius servers. I know that Radius can work because I have another WLAN (the guest WLAN) on the same hardware that is configured to authenticate first against the local database and then against Radius and this is working fine.
(WiSM-slot9-1) >debug aaa all enable
*Oct 09 08:01:44.518:       AVP[14] Called-Station-Id........................X.X.X.X (9 bytes)
*Oct 09 08:03:21.677: Unable to find requested user entry for 6cc26b5990e5
*Oct 09 08:03:21.677: ReProcessAuthentication previous proto 8, next proto 40000001
*Oct 09 08:03:21.677: AuthenticationRequest: 0x18cc933c
*Oct 09 08:03:21.677:   Callback.....................................0x10112bc4
*Oct 09 08:03:21.677:   protocolType.................................0x40000001
*Oct 09 08:03:21.677:   proxyState...................................6C:C2:6B:59:90:E5-00:00
*Oct 09 08:03:21.677:   Packet contains 14 AVPs (not shown)
*Oct 09 08:03:21.678: 6c:c2:6b:59:90:e5 Returning AAA Error 'No Server' (-7) for mobile 6c:c2:6b:59:90:e5
*Oct 09 08:03:21.678: AuthorizationResponse: 0x38f71958
*Oct 09 08:03:21.678:   structureSize................................32
*Oct 09 08:03:21.678:   resultCode...................................-7
*Oct 09 08:03:21.678:   protocolUsed.................................0xffffffff
*Oct 09 08:03:21.678:   proxyState...................................6C:C2:6B:59:90:E5-00:00
*Oct 09 08:03:21.678:   Packet contains 0 AVPs:
*Oct 09 08:03:21.680: Looking up local blacklist 98d6bbde785f
*Oct 09 08:03:21.754: Looking up local blacklist 0013ce73a9e0
*Oct 09 08:03:21.754: Looking up local blacklist 0013ce73a9e0
*Oct 09 08:03:21.778: Looking up local blacklist 0013ce73a9e0
*Oct 09 08:03:21.846: Unable to find requested user entry for 6cc26b5990e5
*Oct 09 08:03:21.847: ReProcessAuthentication previous proto 8, next proto 40000001
*Oct 09 08:03:21.847: AuthenticationRequest: 0x18c6dcc4
*Oct 09 08:03:21.847:   Callback.....................................0x10112bc4
*Oct 09 08:03:21.847:   protocolType.................................0x40000001
*Oct 09 08:03:21.847:   proxyState...................................6C:C2:6B:59:90:E5-00:00
*Oct 09 08:03:21.847:   Packet contains 14 AVPs (not shown)
*Oct 09 08:03:21.847: 6c:c2:6b:59:90:e5 Returning AAA Error 'No Server' (-7) for mobile 6c:c2:6b:59:90:e5
*Oct 09 08:03:21.847: AuthorizationResponse: 0x38f71958
*Oct 09 08:03:21.847:   structureSize................................32
*Oct 09 08:03:21.847:   resultCode...................................-7
*Oct 09 08:03:21.847:   protocolUsed.................................0xffffffff
*Oct 09 08:03:21.847:   proxyState...................................6C:C2:6B:59:90:E5-00:00
*Oct 09 08:03:21.848:   Packet contains 0 AVPs:
I'm assuming thaty the line - Returning AAA Error 'No Server' - is significant but I have configured the Radius servers correctly but a packet trace shows no auth requests whatsoever from the controllers. Has anyone seen this? Anything I should be looking at?
Thanks in advance,
Shane.

The bug I ran into was CSCta53985 on the WLCs. I upgraded to 7.0 and it fixed it. The fix is available in 6.0.188. Depending on your WLC hardware, I would go to at least 7.0.116 for newer AP support, and CleanAir support.

Using ISE guest store via RADIUS

I have a question concerning the guest store on the ISE.
I would like to establish a guest portal on a WLC (currently running version 7.0.220.0). The guest network shouldn’t have any connection to the company network. So I can’t redirect to the ISE guest portal and have to use the local portal on the WLC and pass the login data to the ISE via RADIUS. Nevertheless I want to use the guest store on the ISE.
On the ISE I can only select the internal user store as identity source. But this seems not to include the guest user store.
Has anyone already implemented a similar solution or any idea how to access the guest store?
Thanks
Thomas

I just created a simple setup and tested the login.
It doesn't work with a user created as a guest account.
If I create the user in the normal internal identity store I works fine.
Might there be a difference between ISE Versions?
We are currently using Version 1.1.0.665 on a VM for testing purpose.
This is what the details show:
11001 Received RADIUS Access-Request
11017 RADIUS created a new session
Evaluating Service Selection Policy
15048 Queried PIP
15048 Queried PIP
15004 Matched rule
Evaluating Identity Policy
15006 Matched Default Rule
15013 Selected Identity Store - Internal Users
24210 Looking up User in Internal Users IDStore - tuser001
24206 User disabled
22057 The advanced option that is configured for a failed authentication request is used
22061 The 'Reject' advanced option is configured in case of a failed authentication request
11003 Returned RADIUS Access-Reject
11001 Received RADIUS Access-Request
11017 RADIUS created a new session
Evaluating Service Selection Policy
15048 Queried PIP
15048 Queried PIP
15004 Matched rule
Evaluating Identity Policy
15006 Matched Default Rule
15013 Selected Identity Store - Internal Users
24210 Looking up User in Internal Users IDStore - tuser001
24212 Found User in Internal Users IDStore
22037 Authentication Passed
Evaluating Authorization Policy
15004 Matched rule
15016 Selected Authorization Profile - Guest
11022 Added the dACL specified in the Authorization Profile
11002 Returned RADIUS Access-Accept

Telnet via java

How would I begin telnet via a java app? Do I have to go via Sockets, or something else? thanx

If you are thinking about writing a full function telnet API, take a look at the link below for a Java Telent applet with source code:
http://www.first.gmd.de/persons/leo/java/Telnet/
V.V.

PPPoX Virtual-Template assignment via Radius Attribute

I'd like to optionally apply ACLs to PPP users (PPPoX). I see two strategies: a) apply an ACL directly via radius attributes or b) define the ACL in the Virtual-Template on the BRAS and determine the Virtual-Template ID via radius attribute. Has anyone done this? If so, any suggestions on the best way to move forward? I think I'd prefer option B as I could also use it to assign VRFs etc (one Virtual-Template per VRF).
TIA

The only way I could get this to work is have the ACS server reference an ACL configured on the switch via name or number and send in the filter-id attribute. On the switch I configured the default setting for attribute 11 to apply inbound "
radius-server attribute 11 default direction in". If you do a "sh authentication sessions interface gx/x" it'll show the filter-ID setting but if you do a "show ip interface gx/x" it still shows the default-acl being applied. It works, just a bit confusing because of that default-acl still showing up. Anyone else experience the same?

Authentication via RADIUS

Hello,
we are running an Cisco WiSM in an Catalyst 6509 and we are trying to authenticate our clients against an radius Server.
As Interfaces we have configured´:
Management with IP: 172.17.140.9
Ap-Manager with IP: 172.17.140.10
Virtual IP: 1.1.1.1
Guest Lan with IP: 192.168.6.3
The Management Network is a closed Network with no Internet connection.
The Radius Server we want to use is at an other Location and has an official IP.
We have configured the WLAN to use the Guest Lan as outgoing Interface.
The Security Tab is configured as WPA + 802.1X with Radius Servers set in the AAA Servers TAB
The Controller is configured as AAA Client at the radius Server.
If we try to auth with our Client the Client keeps in "Verifing Mode"
The Controller Log shows "Radius Server x.x.x.x:1812 failed to respond to request (ID 91) for client xxx"
Any Ideas?
Has the Radius Server to be on the same Subnet as the Management interface?
Best regards

Hi,
Actualy i d'not know the solution but require some help from you setting the AP..
Can you please tell me how you have setup the guest access on the wireless device that use username/password credentials? is it using the peap using the certificate or with out it. your response wll be much appriciated.

Telnet via Host?

Hi
Is it possible telnet via host command without prompting user/pass.
if so please help me.
Bcoz I want to connect from client mechine(windows) to server(unix).
Thanks in advance.
Kanish

Hi Kanish,
Create a batch file or shell script in the below format
#Alexyscorp FTP
ftp -n -v alexys.oracle.com <<!
user alex Rasast
bin
lcd ${BACKUP_DIR}
cd /abacus/OFDAP/HOTBACKUP/${WEEKDAY}
mput arch_${FILEDATE}.tar
echo $(date)
close
!

LMS , AAA via Radius and cisco AV pair

We are trying to authenticate users on a Ciscoworks LMS server 2.6 using Radius.
Is there a radius vendor specific attribute that can be used to make the authenticated user part of the admin groups ?
Ex : a Cisco-AV-pair , ?LMS?:groups="Network Administrator"
I have tried a few, but none seem to work. And i havent found documentation on this.

No, It is pure authentication that is done.
There is not way to select a role in LMS based on an AV pair.
With tacacs+ something like that is possible.
Cheers,
Michel

Aaa console telnet via radius

Similar Messages

Maybe you are looking for