About configuration in ubr7200 of CMTS

Hi......
The shown configuraion is ubr7200 CMTS router.
I would like to know each command statement.
Would you explanation me next config ?
I wanna easy explanation. :)
interface Cable2/0
ip address 10.80.0.1 255.255.254.0 secondary
ip address 58.145.127.65 255.255.255.192 secondary
ip address 10.64.0.1 255.255.224.0
ip access-group 104 in
ip pim dense-mode
no ip mroute-cache
no keepalive
cable registration-timeout 30
cable bundle 10 master
cable downstream rate-limit token-bucket shaping
cable downstream annex B
cable downstream modulation 256qam
cable downstream interleave-depth 32
cable downstream frequency 555000000
cable upstream 0 frequency 26000000
cable upstream 0 power-level 10
cable upstream 0 channel-width 3200000
no cable upstream 0 shutdown
cable upstream 1 frequency 31008000
cable upstream 1 power-level 10
cable upstream 1 channel-width 3200000
no cable upstream 1 shutdown
cable upstream 2 frequency 31008000
cable upstream 2 power-level 10
cable upstream 2 channel-width 3200000
no cable upstream 2 shutdown
cable upstream 3 frequency 26000000
cable upstream 3 power-level 10
cable upstream 3 channel-width 3200000
no cable upstream 3 shutdown
cable upstream 4 frequency 26000000
cable upstream 4 power-level 10
cable upstream 4 channel-width 3200000
no cable upstream 4 shutdown
cable upstream 5 frequency 26000000
cable upstream 5 power-level 10
cable upstream 5 channel-width 3200000
no cable upstream 5 shutdown
no cable ip-multicast-echo
cable dhcp-giaddr policy
cable helper-address 61.102.191.20
I wait your answer.......
Thanks.....

After you have completed upstream and downstream configuration in Chapter 2, "Configuring the Cable Modem Termination System for the First Time,"you have additional options to manage how your cable modems (CMs) operate in the hybrid fiber-coaxial (HFC) network. You can set the following CM functions:
http://www.cisco.com/en/US/products/hw/cable/ps2217/products_configuration_guide_chapter09186a00801170f2.html
http://www.cisco.com/en/US/tech/tk86/tk804/technologies_q_and_a_item09186a00800a4ae5.shtml

Similar Messages

Some questions about configuration in MAX.

Hello,everyone!
I have some questions about configuration in MAX(I am a jackaroo for motion control development),I hope I can get your help.
I use PCI-7344+UMI-7764+Servo amplifier+Servo motor,my MAX version is 4.2 and I use NI-Motion7.5
My question as following:
1,In Axis Configuration,for motor type,why I must select stepper but not servo?my motor is servo motor!If I select Servo,my motor can't run,I don't know why.
If I select stepper,though motor can work but I can't test encoder in MAX.
2,In Stepper settings,for stepper loop mode,why I must select open-loop but not close-loop?If I select close-loop,the servo motor doesn't work too.
3,If I want my two servo motors run at different velocity,How shoud I do?It seems I just can set the same velocity in MAX for my two servo motors.
My English is poor,Pls pardon me!I come from China.
Thank you for your help!
EnquanLi
Striving is without limit!

Hi,Jochen,
Thank you for your kindly help!
The manufacturer of the drive and motor that I am using now is Japan SANYO DENKI,drive type is RS1A01AA,motor type is R2AA06020FXP00.
And I use position control mode,thehe encoder's counts per revolution is 131072.I set the electronic gear ratio to 1:1 for drive.
Now,I can use Close-Loop to control the motor but still has some problems.When I configure it to run in closed loop mode, the motors behave strangely and never move to the target position.When I configure it to run in closed loop mode, the motors behave strangely and never move to the target position.The detail situation is as following
1,Motor can't run.
2, Or motor moves to a position, then moves in the same direction agian and eventually stops.
Except for the two points mentioned above,"Following Error" is occured frequently,I don't know why.
I am still not clear why I must set the motor type be stepper in MAX .
And I have another question:what the relationship between the steps and the counts?They have the proportion relations?I notice that there are a section said like this in help document: For proper closed-loop and p-command operation, steps per revolution/counts per revolution must be in the range of 1/32,767 < steps/counts < 32,767. An incorrect counts to steps ratio can result in failure to reach the target position and erroneous closed-loop stepper operation.
I am verry sorry I have too many questions!
I am very appreciate for your kingly help!Thanks again!
EnquanLi
China
Striving is without limit!

When I try to reformat there is an error message about configurations with the pointing device

When I try to reformat there is an error message about configurations with the pointing device
I am not sure I am on the correct section in the support area for Lenovo.
I had a mouse issue. It was unable to read the mouse. Now the mouse is working and it is initialized.
I have no idea why.
There is an error message saying that I should press F 1or F2. I pressed down F 1 and I tried to work with it and I enabled the mouse or I tried. The mouse is working fine but the computer will not recover completely the way it used to.
It is very confusing. When I shut down and restart there is an message that was not there before about the pointing device. Also the recovering operation never asked me for disks. Now it is doing that. I have disks but this is all confusing. I just want the computer to be the way it was. It is working fine except for booting up and the messages.

Hi marissa, welcome to the forums,
you may or may not be in the right place, but it would certainly help members to help you if you could post exactly which Lenovo system; notebook / computer, you have and which operating system is installed on it.
Thanks in advance
Andy ______________________________________
Please remember to come back and mark the post that you feel solved your question as the solution, it earns the member + points
Did you find a post helpfull? You can thank the member by clicking on the star to the left awarding them Kudos Please add your type, model number and OS to your signature, it helps to help you. Forum Search Option T430 2347-G7U W8 x64, Yoga 10 HD+, Tablet 1838-2BG, T61p 6460-67G W7 x64, T43p 2668-G2G XP, T23 2647-9LG XP, plus a few more. FYI Unsolicited Personal Messages will be ignored.
Deutsche Community Comunidad en Español English Community Русскоязычное Сообщество
PepperonI blog

How do you go about configuring colours for terminal [applications]?

I figured this might be the best place to ask but I'm not sure.
I'm using termite, and it has 256 colours predefined. I have always thought that I better define my own colours (override defaults), because the defaults didn't immediately look nice. However, I recently discovered that for example the vim plugin "vim-airlineish" uses colour 55, which matches the screenshots of the plugin - so default colour scheme is assumed. So I'm wondering if this default colour scheme is some kind of global, well known default? And does it perhaps have properties, like: you will most likely find a colour close to the one you want in there, or something else? Is there a name for it?
http://a.pomf.se/dmahvz.png
So what I'm really wondering, is: what is the preferred way to configure the colours of console applications?
Should I leave the default theme as it is and search for the colours I want in this colour scheme?
Or should I find my own set of colours, and choose amongst these when configuring specific applications? This is what I've been doing so far, and for example, I wanted a greenish theme on my desktop, but the default colour scheme doesn't seem to hold a wide spectrum of green colours. (following picture is from my current colours, which I recently set and which I am not really that satisfied with)
http://a.pomf.se/rpeisv.png
Or should I override colours as I need specific colours? An ideal way - but pretty unorderly - to design for instance a colour scheme for coding, would maybe be to use gcolor2/3 to choose any colour that you need, and then put it in the colour scheme. If you could do that easily but you can't really - you have to go through a moderate amount of steps to change one colour, and in the long run of revising, revising, it's just a hassle.
Thanks in advance for any input you can provide on this!
-- mod edit: converted img to url tags. Trilby --
Last edited by Trilby (2015-05-01 11:41:41)

You have a few different only paritially overlapping questions here. How to find a color / is there a name for it: There are 16 base colors, then a 216 color cube, then 24 grayscale colors. You can get a bit more about this from a google search - here's one example:
https://fedoraproject.org/wiki/Features … _Terminals
There are also countless scripts to print out the 256 colors in a useful way in a terminal. These scripts are littered all around these forums - just search and you'll find them.
It is common practice to override the first 16 colors. There are also countless posts - and I think an entire thread - on these forums devoted to sharing these color schemes. I believe it is also possible to override any of the other 240 colors, but it is generally not done and I'd advise against it. These other 240 are generally the ones "assumed". The first 16 have conventional meaning, but there are no specific shades that should be assumed: 1 is some shade of red or something the user prefers in place of red, 2 is some shade of green, etc. 8-15 are bright versions of 0-7.
Also, as you search - please find the forum guidelines and only link to larger images. I converted the images to urls in your post.

Confuse about Configuring Oracle Warehouse Builder

newbie here... i am abit confuse on how to configure the Oracle Warehouse builder...
I have 2 database... 1 source and 1 new one...
I understand that i have to install the Runtime Repository in the database computer and the Target Schema through the client's computer...
so all this while... i am just confuse about what to install into the source database and what to install into the new database...
Please help...

Location is a logical entity in your OWB design that can be either a database schema, a flat file location, an SAP application location etc. Once you complete your design and are ready to deploy the design into the runtime environment, you will have to 'register' the locations by providing the physical details of your location to OWB (user name/password, database, hostname etc.).
I am a bit confused by your configuration - are the source and the target in two separate schemas or in the same schema? Your posts are somewhat contradictory.
If they are in two different schemas, you should:
1. Create a source module pointing to a source schema (you can then import data object structures from the source schema - i.e. you don't have to create source tables manually in OWB, but you can import them into the module automatically). This module will have a source location (for example SRC_LOC).
2. Create a target module where all your target objects will be (i.e. where the data will be loaded). This module will have a different location (TGT_LOC). In your target module you will also create the mappings.
3. When deploying, you will register SRC_LOC with the physical details of your source schema, while the target location will be registered with the physical details of the target schema. The code generated by OWB during deployment will make sure that the data is extracted from the source schema and inserted into the target schema (either by generating and using DB links or by qualifying the schemas in the extraction queries if source and target are in the same database instance).
On the other hand, if both source and target objects are in the same db schema, you can have all your objects in the same target module and you will only have to register the location of this target module when deploying (LOC_TGT).
That said, there can be a variety of reasons why there is no data in the target after you run the extract mapping that have nothing to do with locations, such as logical errors in the mapping (an inappropriate filter or a wrong join), insufficient privileges etc. I suggest you take a look in the runtime audit browser that should contain the error messages relative to your mapping.
Regards:
Igor

Getting information about configured(webservices.xml) web service handlers

Hi Guys, The situation is: In a Web Service, I have few GenericHandlers configured as server(Role) in webservices.xml(for IBM Runtime) & server-config.wsdd(Axis Runtime). Say the handlers are A, B & C. Now, when there is a inbound call A,B & C are getting invoked as expected.
I am basically lookin for a way to know (programmatically) the # of handler configured for this web service i.e., 3 in this case and few other handler specific details.
I was investigating getting hold hold of HandlerChain by following way
HandlerRegistry hndlReg = service.getHandlerRegistry(); List hChain = hndlReg.getHandlerChain(new QName("http://test.com","PortName"));
, but I dont get hChain containing information about A,B or C. Ya, here I can add Handlers programmetically which gets invoked also. But no information of already configured handlers in configuration files.
Is there any way(programmetically) to get the details about already configured handlers.
Appreciating your help.

Please help ....

Information about configuration parameters

Does anybody know where to find information about these parameters in SXMB_ADM - Integration Engine Configuration?
- BPE - DISPATCHER - MIN_DURATION_PROCESSING
- BPE - DISPATCHER - PACKAGES_PER_COMMIT
Thanks!

Hi ,
Please find the below link :
https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/2016a0b1-1780-2b10-97bd-be3ac62214c7
Also the SAP Notes :
1058623
1233380
Regards,
Madhusree

Question about configuring REST web service in EBS instance

I am from EBS SCM team. From one wiki page, it says OA Framework provides REST framework to expose OAF BC4J objects as web services. Can you provide more details about how to configure REST web service for one EBS instance? Any related information is also helpful.
Edited by: 936859 on Sep 7, 2012 5:45 PM

IIRC you must activate PAPI-WS for the engine. In Studio you do it by right-clicking on the project, then "engine preferences". In enterprise/standalone you must activate PAPI-WS in the Admin Center.

About configuring IM in multipile domains

Hi all,
I can use IM service in single domain, but when I create more domains in DA, users in other domains can't sign on IM service. And I saw the error message from console as the following
WARNING: Attention! The organization o=isp is not associated with any domain name. This will cause security issues in multi-domain deployments. Please set a domain name for this organization, using the Identity Server Administration Console.
When I add the main domain name in organization o=isp via AM, the I can sign on in another ID within another domain. When I sign on DA, I will see the domain called isp and I click the domains link, it will let me sign out right away.
By the way, if there are three same ID within different domains, how should I configure the setting to sign on with full email address, not just ID only?
Please help me to correct them and thank you in advance.
|-o=isp
|--o=mydomain.com
|----ou=People
|-------uid=test.01
|--o=nw.mydomain.com
|----ou=People
|-------uid=test.01
|--o=jp.mydomain.com
|----ou=People
|-------uid=test.01
|--o=sd.mydomain.com
...

Dear Swetha,
I am very idiot. I misunderstand what you mentioned in last reply If you want the login attribute to be mail then,Replace the uid occurences in the above two
parameters to mail,else leave it as default.
I modified them by following your instruction like below
! iim_ldap.loginfilter = "(&(objectclass=inetorgperson)(uid={0}))"
iim_ldap.loginfilter = "(&(objectclass=inetorgperson)(mail={0}))"
!iim_ldap.useruidattr = "uid"
iim_ldap.useruidattr = "mail"
And restart IM service, I still can't sign on with full email address and only can sign with UID.
Thank you for your patience.
1. I did check /etc/opt/sun/identity/config/AMConfig.properties and it did show com.iplanet.am.locale=en_US
But it is still shown other language. Is there other setting I missed ?
2. I added Domain Name by following your instructions, but I have question, what kind of "Domain name" should I input in organization o=isp , if I leave it blank, after restart IM, I will get some error message on console while sign on IM as before(I know what you talked before) as following
# WARNING: Attention! The organization o=isp is not associated with any domain name. This will cause security issues in multi-domain deployments. Please set a domain name for this organization, using the Identity Server Administration Console.
If I put one fake virtual domain in o=isp organizatioin, it won't show that error message, but while I try to sign on IM, the console will show the error as following
[Fatal Error] :-1:-1: Premature end of file.
3. I did search in Forums by key word "show contacts automatically", but can't find anything about showing contacts automatically after signing on IM.
Would you please give me a hand to let me know which POST there ?
Thank you in advance.

The question about configuration Organization Unit on spro

Dear all.
I want to configuration Organization Unit on spro so I have created O.Units, Jobs and positions on Personnel Administration->Organizational Assignment->Organizational Plan but I can't see these values about O.Unit, job and position on SAP Access Easy .
How to see these values on SAP Access Easy ?
Can I input these values about O.Units, Jobs and positions on spro ?
Thanks so much.
Huyen Nguyen

instead of that
Define the Number ranges
in OOCR
for all the objects
Make a Template for Objects and Object Id
and upload the same thru PP01
than all the enties will sit in the SPRO
>note it is not mandatory to create thru SRPO wht in case if u have 4000 to 5000 Employees
So the best way is upload the Data thru LSMW thru Proper objects and Relatioships

Where can I find help about configuring forms?

Hi, everyone,
I want to develop web-based application using forms 9i, but I don't know how to configue my developing enviroment. I searched in forms online help and otn website, but I found nothing, except some articles about forms service. but I don't think I need install forms service when I develop my application. so who can be so nice to tell me where can I find help about this problem.
besides, after creating a database in my local machine, how can I connect with it in foms?
thank you very much!

If you installed Oracle9iDS you'll have everything configured for you. (It basically work the same way as the Oracle9iAS Forms Services so all the documents are still relevant). For a quick understanding of the configuration files check out this document: http://otn.oracle.com/products/forms/pdf/forms9icstowebmigration.pdf
To connect to your database you need to create a SQL*NET connection and add an entry to your tnsnames.ora using the SQL*NET easy configuration tool.

About configuration web dynpro abap

we have ecc5.0 and we cant use web dynpro there. can anyone please tell me how can we use web dynpro there? is it related any sap license related issue? please help me about giving me some knowledge about web dynpro installation and use.
From web every user should need one sap id or one common id can be use for login through web.

>please help me about giving me some knowledge about web dynpro installation and use.
There simply is not option to install or configure Web Dynpro ABAP on ECC 5.0 or earlier. Web Dynpro ABAP is part of the SAP_BASIS Software Component. The versions of ECC 5.0 and earlier simply didn't contain Web Dynpro ABAP. It was new in ECC 6.0.
If you want to create Web Dynpro applications, consider building a standalone ABAP or Java Application Server as a separate instance. You can then do Web Dynpro ABAP or Java development on this standalone instance and make RFC and Web Service calls to your older ECC 5.0 system.

Doubt about configuration IPCCX 5.0

Hi Guys,
My Customer have a solution with 02 IPCCX Server version 5.0 (Publisher and Subscriber). I would like know if is possible configure any parameter in IPCCX to that inform (about alarm, e_mail, or another form) when the IPCCX to stop generate of backup. Is there this possibility in IPCCX?
Thank You,
Wilson

Hi,
UCCX can be polled by an SNMP collector and also send alerts to a syslog server on the network. You can have any SNMP collector poll UCCX and you will get events back, like the one you have described, if the Cisco Alarm Service is running. All subprocesses of UCCX report their alerts to this process which then serves them to the collector when it is polled.
Alternatively, you can use the AppAdmin->System->Alarm Configuration to configure a syslog server and the level of alarms that are sent. Then, use AppAdmin->Tools->Alarm Definition to see which ones you want to filter.
You're most likley going to filter/trap:
Catalog MCVD-ARCHIVE_MGR
Name BACKUP_FAILED
Description Backup of the cluster failed
Severity CRITICAL_ALARM

About configuration ADF BC

Hi all,
I want to ask about the configuration for database connection in ADF Business Component. For me the db configuration must be defined when we create Application Module at the first time. So, it was flexible for me. I found another java technology which similar with ADF BC can read db configuration from the external file. So, I want to know can ADF BC read from the external file?
Thanks for the advice..

I don't know if I get your question right, but the configuration is stored in a file. So it's read from an external file.
Timo

Question about configuration (ATI 5770) w/ 3 monitors

Ok I already know how to get three monitors running on the ATI 5770. I have one native mini DisplayPort, one mini DisplyPort to VGA and one native DVI or DVI to HDMI. What I need to know (before I buy another native mini DisplayPort monitor) is if the 5770 can run two native mini displayPort monitors and a native DVI? Has anyone done this?

i am currently running 3 displays on my macpro 1,1 with a 5770 card. here is my setup
mini display port to dvi (dual link active from monoprice) to an Acer 24" monitor
mini display port to dvi (sme as about) to and dvi to hdmi adapter to 65" 1080i television
dvi port to Acer 24" monitor.
i have to set it up this way because if i set both monitors to mini display port adapters and the tv to the dvi to hdmi adapter one of the monitors will not come on. setting it this way all three monitors are working. the only problem that i have is that my tv monitor flickers like the computer is refinding it all the time. i haven't really had a chance to look into it too much, but i can tell you that without the active link adapters only two of the three connections will work at one time.
hope this helps

About configuration in ubr7200 of CMTS

Similar Messages

Maybe you are looking for