About K7N2 Delta-ILSR SATA

I am already used up all the PATA/ide connector (for 2 optical drive, and 3 HD), and want to add a new HD...
Soo i am want to use the two idle SATA connector on my motherboard, the problem is: I don't need the RAID function, just plain SATA HD
is that possible?...i read the manual said it only for raid, and i don't want to make a wrong HD purchase(cause RMA can be pain in my ass in my condition)

Quote from: mechwookie on 09-September-05, 16:15:12
Like you want to, i've just started using my SATA connections.
You have to use it as RAID, theres no way around it. However, how you set it up is down to you. Raid 0/1 whatever.
Can't answer anything myself with regard to just using the the SATA's for another set of storage would be worth it in the long run or not, but will say this, Installing on the SATA's take a lil less time than using a standard IDE drive (just ya basic 7200rpm SATA, not the 10k Raptors which some say can install XP in under 20mins)
Will say this, just what are you planning to use the drives for? And can you post a sig with all you system details in it, including you ram make, and PSU voltage rails current capacity (that last bit is kinda compulsory when it comes to this forum )
Soo there no other ways heh...maybe i suppose just swamp one of the old HD (40gigs) with the new one(200GB likely)
THe new drives should be just another generic volume aka not for installing OS...because the old ones getting full AGA!N...
Haven't i post all the details in my sig?...ow the rail capacity are:
Vcore 1.63-1.7,
3.3v=3.3-3.4,
5V= 5-5.1,
12V= 11.4-11.70
I think it still OK just +- 5% from the real voltage.........

Similar Messages

Questions about K7N2 Delta-ILSR

I am planning to buy a K7N2 Delta-ILSR motherboard, so I have a few questions about it.
Firstly, I would like to know which the max FSB the motherboard can handle is. )
Secondly, which are the available multiplier numbers?
Furthermore, i would like to know if the K7N2 Delta-ILSR version has standard the MCP2-T chip. In advance I would like to know, if it supports the SoundstormTM technology
Thanks

madsteeve1,
1) I have seen people running over 425Mhz.
2) Download the manual and check the BIOS Revisions for that answer
3) The -ILSR Boards have Soundstorm.
Take Care,
Richard

About k7n2 delta ilsr.

I would like to buy this mainboard:
What contains MSI K7N2 DELTA ILSR mainboard package (D-Bracket, S-Bracket, plugs...)? Is fan speed dependent on temperature? ?(

I just got my Delta tonight, gonna put it together at the weekend, so looking in the box my UK spec contains, 1 mobo, FDD cable, Round IDE cable, SATAcables+Powercables, D Bracket2, 1394 bracket, S Bracket(SPDIF-Analogue connnectors) 2 CDs & a Raid Floppy,2books, Backplate and a sticker. Also by mistake a TV out bracket thats not for this mobo.
Hope that helps
waveydavey

K7n2 Delta Ilsr + Sata!!!

I have bought a nice sata hd: seagate 120 gig, but i don't know how to boot it....
I used fastbuild, but me sata drive only appears in windows and i wan't to boot windows from it, but in the bios i see no options for sata
so I wondered if anybody knew how to use sata with this mainboard i would be very happy!
greetz junky

create the array in raid bios
have it as only drive bar a cdrom in box
set scsi second to cdrom in boot order
hit f6 as xp starts and feed in drivers

K7N2 Delta ILSR SATA Performance Questions

hello
does anyone know if there are drivers that will increase performance? i just got a WD Raptor and ran a benchmark and it runs at 47 MB/s. shouldnt i be able to get almost 150 MB/s ?
any suggestions would be greatly appreciated.

as i said no drive exists that moves data that fast
they will all shift the 2 or 8 mb they have cached at the full bus speed
after that they get no were near it
there is nothing wrong with that result
but sandras not a good benchmark for drives

[nForce] K7N2 Delta ILSR - Do i have to have raid with sata drive

Hi guys,
Probably a really stupid question, but here goes
My machine has 1 ide HDD and 1 SATA HDD.
The SATA drive is set up as raid0 and is purely used as a data disk. The OS(win xp pro sp1) is on the IDE drive
The only way i could get the SATA HDD recognised by windows, was to set up a raid array with just the 1 disk.
Pretty useless raid array i know.
Did i have to do this or is there a way to have the sata hdd usable without having to set up a raid array
Thanks
John L
MSI K7N2 DELTA ILSR
ATHLON XP 2500 Barton
2X512 MB PC3200
Leadtek GF4mx460
WD 8MB CACHE 80Gb IDE
Samsung 120Gb Sata

you have to do it for the controller to work
but it has no effect on the drive
you can move a regular drive on ide 3 back to a normal ide and its all fine

Sata boot with K7N2 Delta-ILSR

I have a K7N2 Delta-ILSR board and can't load the os to the sata drives. Both drives are new and raid 0. The load sees no drives and the raid drives don't show in the boot device menu in the bios. What have I missed? Is this possable?
Thanks for any help,
Mike

so you made the array control plus f i assume
have you set scsi second to cdrom
then hit f6 as xp install starts
and feed in drivers

MSI K8T Neo2 F vs. MSI K7N2 Delta ILSR

Hi there !
I have an amd Athlon XP 3200+ overheating problem, and contacted the technical support of the shop where the processor and CPU was coming from.
Since they do not have any XP 3200+ to replace mine, they propose me to replace fro free :
- the XP 3200+ by an AMD Athlon 64 3200+
- my actual MSI K7N2 delta ILSR by an MSI K8T Neo2 F
... and this for free.
Since I do not know this new motherboard that has been proposed, I'd like to have advice on if this is a good deal ?!?
My actual system has :
- an Aluminium case with 2x 12cm FAN's
- 2 IDE hard drives
- 1 SATA hard drive
- TWINX Corsair XMS 2x256MB PC 3200L (Extreme low latency)
- an AGP 8x video card
- An Antec True Power 480W.
will the new motherboard fit with this configuration?
Many thanks for your input !

Not really, unless you really want to oc your cpu. The K8T boards aren't that good in OC-ing. But still, some is possible and you'll be sure that the board is as steady as a rock.
For a moment I thought you were talking about a Neo board ... but I just saw it's a Neo2. That means Socket 939 -> dual channel RAM.
The only risk you have now, is that your RAM won't work in dual channel with the CPU. But that's not really a board-problem, more a CPU/RAM-controller related problem. But then, it's still a great offer and chances are good that it will work. If you run into any trouble, RAM-related, just flash bios to version 1.9 and you will probably be just fine.

MSI K7N2 Delta-ILSR Nforce2 (Socket A) Motherboard (MB-003-MS) Features NF2 chip

I tried to install 3 of the Crucial Ballistix Tracer (1 Gig Each) in this motherboard (MSI K7N2 Delta-ILSR Nforce2 (Socket A) Motherboard (MB-003-MS) Features NF2 chipset) and it will not run stabilly no matter what I tried. Is this a bios conflict with the memory? If so, are there any new bios updates? I have tried cas settings and voltage settings but nothing works. It will how ever run perfectly with only 2 sticks in single channel mode. It will not run same 2 sticks in dual channel mode. Anyone have any ideas? Anyone know of any new motherboards with maybe NFORCE 4 Chipset that support all 3 sticks of this memory and an AGP graphics card? Im thinking of a new motherboard but I still need to have AGP and SATA.
Barton 3200 core proc.
System has ran fine for a solid year until I tried new memory. Please help!

Quote from: freakytiki4u on 07-November-06, 23:42:33
Ok I tried to use relaxed FSB by -10 and relaxed mem timings but still unstable due to the motherboard trying to use dual channel memory. If you can modify the bios to where it will not have the capability of dual channel memory I truly believe it will work. Will u try this for me? I would greatly appreciate it as I am really not ready to spend all the money on new equipemtn when this suits my needs for now.
sure but as i said before this is gona be experimental and risky. Here we go:
MSI K7N2 Delta ILSR Experimental MOD E1(Disable Dual CH ability)
Procedure is automated in best possible safest way to BIOS update.
Prepare a blank diskette in a good condition(newest one etc.)
]execute file under XP will make bootdisk with automated BIOS update procedure. when diskette is ready, reboot PC and boot from FDD(floppy), wait a bit, then you will be asked for final confirmation about BIOS update process, press a key to proceed, after BIOS update is complete, ensure that you got successfully output message from flash program. then power down your PC, remove power cord from the PSU, hit power button several time to drain caps electrify, touch with hands some metal for ES discharge, and Clear CMOS.
pull back power cord, power up your PC, when you see CMOS checksum error,(expected msg) hit F1 to continue to re-build DMI pool data, then reboot and enter in BIOS, LOAD BIOS DEFAULT, and SAFE AND EXIT.
NOTE: Ensure your PC is stable before proceed with BIOS update.
NOTE: Use it at own risk, chance of failure is big, cannot guarantee results and safest as provisional mode which can guarantee it will work stable with features. also cannot test it personally before give you. (don't have mobo anymore)
Using it may end with dead mainboard (BIOS chip re-flash will be required, if somethink goes wrong)

MSI K7N2 Delta ILSR (MS 6570) trouble With ATA card

Hi, i have major trubble.
Ihave two 300gb, two 120gb and two 80gb harddrives + 1 DVD burner and 1 CD burner with ultra DMA 100 PCI card and it works fine without using the sata or ide3 raid function. I purchased an new PCI ATA 133 card and the system won't boot. I have tried for an long time to get the raid function to work but wihtout results with my old ATA 100 card (it works when i unplugg the ide cable from ide3).
Is there anybody that knows with type off PCI ATA 133 card that works or how too coop whith this problem.
I've got the latest bios ver. 7.8 but no difference
AMD XP2800+
Kingston 2x512mb
ATI Saphire Radeon 9600pro 256mb
Soundblaster Live Value
XP pro sp2
MSI K7N2 Delta ILSR (MS 6570)

I went to JME-Data and purchased an
True430
ATX 430 Watt Power Supply with PFC
For AMD™ and Intel® systems including
Pentium® 4
Dedicated output circuitry
Voltage feedback
Antec Low NoiseTechnology
AQ3 - Antec 3 year parts & labor warranty
True430 is a 430 Watt 6-output, dual fan-cooled ATX12V (Baby AT or PS/2 Size) power supply designed for personal computer or industrial applications.
Its ATX12V compliance allows its use with the latest Pentium 4 processors while its backward compatibility ensures its usability with any ATX-based AMD™or Intel® system
The prise 1099:-
And everything works great, Thank you very much for the tip. :-)
No more blue screen and it even works with my memory Kingston Value Ram 2x512 ddr400.
Is it possible to change the FSB from 166 to 200, and what should i think about before action. Like i said before i have an xp2800+
Alltså är det möjligt att få cpu gå på samma frekvens som minnena om man ökar FSB har några tip så är jag tacksam.
Att en nätdel kan göra så mycket helt otroligt TUSEN TACK för hjälpen till och med cpu tempen har sänkts från ca 56 till 46 grader fattar ingenting.

K7N2 Delta-ILSR BSOD

Hi
MSI Nforce K7N2 Delta-ILSR
Bios V1016
Antec True380SPGB True Power 380w
AMD Athlon XP2800+
2x512mb Crucial DDR
1xSATA HDD
Abit Siluro GF4 Ti4200
I've installed 1 SATA onto the onboard Raid controller, but I keep getting BSOD when either playing a game or watching avi's. The 0x00000000 message is disappearing too quickly to right down but is saying windows was shut down to prevent damage to the hardware.
Will the K7N2 Delta-ILSR Promise controller work with just one SATA hdd connected, I know that the silicon image controller on my Asus A7N8X-E will support just one SATA connected but will the promise chipset.
I've updated all the drivers but the dreaded BSOD keeps happening.
If it won't it not's a major problem as I do have a PCI sata controller card I can install.
Or are there any issues with the above graphics card and the MSI mobo?
Thanks for any help.

Yep I've created a array with the single SATA and got Windows installed.
I've also changed the memory settings so they are now 1:1 with the FSB.
I've also altered the advance settings so I'll be able to write down the full 0X00000000 string.
Just set net access up via my PC and got this error report from M$
Error Message: STOP 0x000000EA THREAD_STUCK_IN_DEVICE_DRIVER (Q293078)
Error Caused by Graphics Device Driver
Thank you for submitting an error report. Microsoft is unable to determine what specifically caused the problem you reported. To troubleshoot the problem, please see the information listed below.
Analysis
A device driver installed on your computer caused the problem, but we cannot determine the precise cause. Depending on which situation is applicable to you, please do one of the following:
* If you are running Windows Server 2003 you may experience crashes if you have adjusted the Hardware Acceleration setting. Microsoft recommends that you set the Hardware Acceleration setting to None for server systems. To check your Hardware Acceleration setting, go to the Advanced section of the display properties dialog box.
* If you know the manufacturer of the device, contact the manufacturer's product support service for assistance.
* If you don't know the driver's manufacturer and need help diagnosing and resolving this problem, contact your computer manufacturer's product support service.
* Updated drivers might be available on the Microsoft Windows Update website. At Windows Update, you can have your computer scanned and, if there are updated drivers available, Windows Update will offer a selection of drivers that you might be able to use. To learn more about updated drivers that might be available, visit Microsoft Windows Update.
* For information about Microsoft support options, visit Microsoft Product Support Services.
I've downloaded the current graphics card drivers from Abit and I'll install them and see what happens.
I've also adjusted the AGP in the bios from 64mb to 128mb.

NEED HELP - K7N2 Delta ILSR

I really need help. I recently bought my new moboard the K7N2 Delta ILSR and with it a GeForce FX 5600 256DDR, 512 DDD Ram PC3200, an 80Gb Seagate SATA HD, andi have a 2800+ AMD Athlon Xp Barton Core Cpu. The problem i get is that when i try to install Windows XP it says it cant find any hard drives. I saw the other thread that was like this but that one had about RAID so i thought i would ask again. I even tried it with Windows 98 which finds my hard drive and even installed once but after that i tried to upgrade to Windows Xp which didnt work, overwrited some of my Windows 98 files and so that didnt work either and when i try to install it again it gives me errors. PLS help im desperate to get my lan workin with my other PC. I havent changed any options in the bios and i dont know if i have to change anything to make sata work. I dont have a floppy disk either for the hd. I found it in the array thigy as well.

Windows will not find a SATA drive you have to tell it you have one bios will only find IDE drives.
you must hit ctrl F when the screen comes up during boot and creat an array just follow the on screen promps.
If you bought a OEM board and don't have the SATA Promise disk download it from MSI and a Manual too.
Either a Raid 0 or Raid 1.
It looks like you have only one drive so just tell it that and the array will work.
Than go to your Bois and set Bois to boot from CD first SCSI secound.
Now you can load your OS. When your OS starts to load it will flash a line across bottom of screen asking if you have SCSI hit F6 do so. The OS will keep loading but when its done it will ask for you 3.5 promise disk. Put it in and load the Fast Track 376 program.
When you OS is finished loading it will again ask for this disk as the first time it just loads the drivers to memory the secound time to your HDD.
Good Luck it a little confussing the first time as the programers think there talking to techs not people so use terms that sometimes don't make sense.

Help! amd xp3000+ barton temp's.... k7n2 delta ilsr

Hi all, (sorry for the lengthy post)
Ive recently built a new system based on the K7N2 DELTA ILSR, great mobo, however my cpu temps are extremely high! on idle 48C and on load nearly 60C. the mobo temp hits approx 40c on load and 34 on idle.
I had an issue with cooling as the cpu heat diode would freeze my pc as it was hitting temps of 58c on idle. i was using the coolermaster aero 7+.... no good at all!!!!! even when on full rpm. Now im using a vantec 80mm fan on a Thermalright SLK-800A. much improved, however still extremely hot.
after reading this review (section headed: Heat Dissipation: Thermal Conditions and S2K Bus Disconnect) :
http://www.xbitlabs.com/articles/cpu/display/athlonxp-3000.html
......on "S2k bus disconnect" created by AMD for the barton range.
As the article states, it reduces Cpu temps ALOT!! but im not too sure ion how to activate it or even if my MSI motherboard supports it....
Can anyone shed some light???
system:
Radeon 9800
1GB 3200 Ram
xp 3000+ Barton
Sound Audigy 2
Thanks, Sav

Sorry about the long reply!!! the first thing i would like to say is why does this happen at 58C even with the bios temp settings diabled??? pehapes MSI could Answer this?
I have spent countless hours trying to fix this problem and a lot of £££. A bit of background to me I am a design engineer and i like my PC to work well. I have the following main components
xp3200+ based system (Max die 85C)
with dual 512ddr sticks running at 400mhz
Matrox Parphilia
10K SATA hard disk
7,200 133ATA hard drive
Plus motherboard Nvidia chipset
these all kick out a lot of heat the (CPU contributing 76.8w).
first i started out with a very cheap case and standard amd heatsink. I found after about 5 minutes my pc kept crashing i automatically thought that it was probably the case temperature so monitored this found every time cpu reached 58C it crashed on the dot. The only conclusion i can draw from this that this MB has some thermal protection that can not be switched off but i am guessing perhapes MSI would like to answer this.
I quickly decided as an engineer that the best thing would be to go and buy a aluminuim case with lots of case fans (Basically a big heatsink itself). After a lot of searching i settled for a Coolermaster ATC110. It has four case fans all run at full speed all the time. Now this stoped the crashing problem it only now crashes if i put it under continous loading. Then i went out and bought a new cpu heatsink to replace the amd standard one. This had a minor effect on cpu temp but again under high loads the system crashed at 58C. Obvoiusly as an engineer i satred to think that the amount of noise the system with all its fans going at max is like being put in a wind tunnel.
I then turned to looking at the thermal diserpation requiremnts of all the bits in my system. I worked out that i need to disserpate 281Wmax of heat with my current setup. The kind of heat a small electric fire produces!!!. I begun to wounder if i could shift enough air through the two exhaust fans at the rooms ambient temp to do this. After some calculations I found that my case exhaust case fans are only just surfficent to disspate this amount. Which could explain this the crashing. because the higher the case temp the lower the capability of the heatsinks to conduct heat away from the item.
In the end i gave up with active cooling methods (heatsinks and fans) and realised my only option was to go for external cooling. I now have the system setup with a koolance exos cooling both hardisks graphics card cpu and MBchipset. I know this is very extreme but the case fan noise got to me now i have disconected all case fans except for the ones in my thermaltake power supply which are virtually silent. After about 12 evenings of testing and installation I now have a system which is not only stable but the CPU temp is only 32C.
Obvoiusly getting the heat out of the case is a good idea. The Exos is only running at it's lowest setting which means the fans arnt making any noticable noise.
MOST IMPORTANTLY IT DOES NOT CRASH ANY MORE. AND THERE IS THE PSSIBILTY OF OVERCLOCKING.
The question still remains though why 58C?

Someone plz help me with my k7n2 delta-ilsr

Hey everyone,
I just put my sytem togother and ran into a problem. I got the system to boot up just fine. It was not until I tried installing windows xp proffesional that I ran into problems. The installation process runs pretty smoothly, until the computer reboots to run windows for the first time. After it reboots the windows logo appears and the after 2 seconds or so, a blue screen appears saying that windows was shut down to prevent any damage to my computer. I have never encountered this problem before when I built other systems. The screen suggests that I should check my HDD's for viruses or check to see if they are configured correctly. The HDD's are SATA and I have them set up in RAID 0 mode and yeah I installed the RAID drivers during the installation process. Thinking that I had made mistake setting up the SATA drives, tried installing windows using a regular IDE hard drive and it gave the same message. I am stumped anybody have any ideas of what I might be doing wrong? Any help would be appreciated . My system specs are below.
MSI k7n2 delta-ilsr mobo
AMD 3000+ Athlon XP cpu (333 fsb)
ATI Raedon 9000 ( I know it's crappy , I'm still saving up for the ATI all in wonder 9800 )
x1 kingston 512mb pc3200 DIMM
x2 maxtor 80gb maxtor hdd's
x1 regular cd-rom drive
x1 floppy drive
420w raidmax psu
(+3.3v = 26A, +5v = 32A, +12v=13A)

Memory that comes with timing of 5 2 2 2 or 6 2 2 2 or usally winbond BH-5 memory chips. Ones with 5 3 2 2 or CH-5 winbond chips. The BH-5 chips overclock a little better than the CH-5. (Muskin uses BH-5 winbond in there black ram)
Winbond is no longer making BH-5 chips but is going to make a limited run of them as demend is high for them.
The first number shown here is the Traz and it controls the flush timing bench testing is showing that a higher number of 9, 10 or 11 or getting better bench results than the 6 or 5. Thats with Dual Channel memory.
The timing you show probly should be something like 8 3 3 3 or 8 3 3 2.5 unless it is there faster Dual channel ram.
The timing numbers can also appear like this 2 2 2 5 the high number is the Traz either way.
Look on your memory manufactor web site for the timing that if should run at also look at the voltage as this can make a big differance.

Internet Connection Problem on MSI K7N2-Delta-ILSR

Hi, recently I buy an MSI K7N2-Delta-ILSR.I have a problem when I was trying to connect to the Internet through my modem on WinXP Pro SP1. It bring me up an error message 678 ( The computer that was tried to connect did not respond...). I have also a second hard disk with Mel windows. On disk the disk with the Mel I don’t have any problem with the internet connection. All my settings are same on WInXP pro and Mel.I have checked I thousand times. My computer configuration is:
Athlon XP 2400+ Overclocked to 2205MHz
2 memory modules of 256MB 400 manufactured by Samsung
TharmalTake Volcano 11
Triplex Xabre 400 PRO with 128MB
Hercules Gamesurrround Fortissimo III 7.1
Microcom InPorte Home modem 56k
Leadtek winfast 2000 (TV/FM radio)
Acard SCSI controller (Acard AEC-6710D) for my scanner
WesternDigital WD800 GB
WesternDigital 15.3gb
Bios ver.7.4
Can anyone help me?

Quote
Originally posted by Roger Wilco
Hmmmmm, I\'m also having a problem with the onboard lan of the K7N2 Delta.
I have an ADSL connection, and have an Alcatel SpeedTouch Home modem.
I pretty much get the same error as SiliconMan (The computer that was tried to connect did not respond...)
I ended up giving up on it for the time being, just using my SMC NIC. Would be quite interested in finding out what the problem is though.
Anyone else in the same boat?
Hi,
Your problem is not the same, SiliconMan is trying to connect with a dial-up modem not LAN. Your problem sounds like it may be configuration, do a search on this post, I'm sure you will find people with onboard LAN troubles. It's hard to troubleshoot though since you didn't provide any info about your computer. Good Luck
Rob

About K7N2 Delta-ILSR SATA

Similar Messages

Maybe you are looking for