About RAC how to change san

hi,
we have setup of oracle 10g rac on aix , now we want to change our san hardware which is our shared storage and add new san at place of old one. my database is on san which is running.
so is it possible to replace old san machine with new one ?
if yes then how can i do this ?
Regards

Hi,
we have setup of oracle 10g rac on aix , now we want to change our san hardware which is our shared storage and add new san at place of old one. my >database is on san which is running.
so is it possible to replace old san machine with new one ?
if yes then how can i do this ?Its a complete hardware replacement, you need to configure your servers with your new SAN storage.
Your OCR, VD and DB on which file system??
I believe this should wok:
1) Configure the new SAN storage luns on Existing RAC servers.
2) Move the datafiles from old Storage LUN location to New Storage LUN location.
3) un configure the luns from db and server.
4) Remove old storage.
I suggest you to open S.R and confirm the same.
thanks,
X A H E E R

Similar Messages

Oracle 10g RAC - two nodes - change SAN storage - only one node up

Hi all,
We're using Oracle 10g with Linux Red Hat.
We want to migrate to another SAN storage.
The basic steps are:
node 1:
1. presents the volume disk and create partition
2. asmlib create disk newvolume
3. alter diskgroup oradata add disk newdisk
4. alter diskgroup oradata drop disk OLDDISKOTHERSAN
But THE NODE 2 DOWN.
we want start the NODE 2 only after ALL operations in node 1 finish.
What's you opinion? Any impact?
Can I execute the oracleasm scandisks on node 2 after?
thank you very much!!!!

modify the commands just slightly...
1. presents the volume disk node1 AND node2
2. create partition node1 [if necessary?? ]
3. asmlib create disk newvolume [node1] ## I am not a fan of and have never had to use ASMlib - however, apparently you do...
4. asmlib scandisk... [node2]
[on one of the nodes]
alter diskgroup oradata add disk1 newdisk rebalance power 0
alter diskgroup oradata add disk2 newdisk rebalance power 0
alter diskgroup oradata add disk3 newdisk rebalance power 0
alter diskgroup oradata add disk{n} newdisk rebalance power 0
alter diskgroup oradata drop disk1 OLDDISKOTHERSAN rebalance power 0
alter diskgroup oradata drop disk2 OLDDISKOTHERSAN rebalance power 0
alter diskgroup oradata drop disk3 OLDDISKOTHERSAN rebalance power 0
alter diskgroup oradata drop disk{n} OLDDISKOTHERSAN rebalance power 0
alter diskgroup oradata rebalance power {n}
You can actually do this with BOTH nodes ONLINE. I was involved in moving 250TB from one storage vendor to another - all online - no downtime, no outage.
And before you actually do this and break something - TEST it first!!!

I have downloaded an update to Firefox, but when I try to load it I get this message, "The operation cannot be completed because you do not have sufficient privileges for some of the items" and I have no idea what it is talking about or how to change it.

The previous version of Firefox is still on and operational. I get this message when I try to drag the Firefox icon to the application file icon. Since this is my computer, and I am the administrator, I don't know what privileges I lack, or on which items. If there is a way to correct this I would like to do so and activate the new version. It looks like the new version is 7.0.1 for Mac OS. This happens everytime I try to load the new version by dragging the icon.

If there are problems with updating or with the permissions then easiest is to download the full version and trash the currently installed version to do a clean install of the new version.
Download a new copy of the Firefox program and save the disk image (dmg) file to the desktop
* Firefox 7.0.x: http://www.mozilla.com/en-US/firefox/all.html
* Trash the current Firefox application to do a clean (re-)install
* Install the new version that you have downloaded
Your profile data is stored elsewhere in the Firefox Profile Folder, so you won't lose your bookmarks and other personal data if you uninstall and (re)install Firefox.
* http://kb.mozillazine.org/Profile_folder_-_Firefox

How to change the path for a file download? Sometimes, I want to save a file in a specific folder in my hard disc and I don't know how to do it. Thanks.

There is a default folder for the download of files from the internet ("Descargas" or "Downloads"). But, what can I do if I wish to save the file in another location of the hard disk?
Thank you.

Use about:config and filter on browser.download, you'll see them
'''More information on configuration variables''' available in
[http://kb.mozillazine.org/About:config_entries about:config (entries)] and for users not familiar with the process there is [http://kb.mozillazine.org/About:config about:config (How to change)]

How to change of NAME and IP after RAC installation.

Hi Friends,
I have a challenge here...Would appreciate if anyone can help me..
I have to install 10.2.0.3 Oracle RAC on windows 2003 server 64 bit.
My issue is now the server names and ips are set and I am going to install the RAC.
But the client need is that after one month, they need to change the names and ips of the servers (a one time change).
Because according to their server naming standards, current production servers are having the acceptable names and ips.
The installation was on a 32 bit OS, so they are facing out of process memory errors. Thats why they are going to 64 bit OS on new servers.
After the new servers are ready, the data will be migrated to new server. After a month, they need to change the names of new servers to that of the old (current production) servers.
Could anybody help me by giving me information about how to change the NAME and IP after a RAC installation ?
Any metalink notes or commands as it is........
Thank you,
Mahesh.

Hi,
You can change the IP later but you can not change the hostname of the system.
You have to install CRS freah if you want to change the hostname of the system.
Please let us know which IP you want to change.
You can see the metalink Note.276434.1 for VIP or VIP hostname change.
Regards,
KK

For the life of me, I can't find out what size a photo is in terms of inches or how to change the size of the photo[s] so I can print them. I think I read somewhere to click edit, then click adjust. Nothing there about sizing.

For the life of me, I can't find out what size a photo is in terms of inches or how to change the size of the photo[s] so I can print them. I think I read somewhere to click edit, then click adjust. I don't see anything about re-sizing when I click the adjust tab: only saturation and tint levels. Thank you.

With respect to digital images, there really is no size in inches. The size is given as number of pixels horizontally and vertically. In iPhoto '09 you click the little "i" inthe lower right side of the window and it will display information related to the selected photo, including the pixel dimensions. I do not have iPhoto '11 installed so I don't know if it is the same there.
In some applications, such as preview, it has something additional called Dots per Inch (DPI) which you would think would allow you to convert the pixel dimensions to inches. It is not a real thing, though. The DPI is determined by how large or small you have chosen to print your photo and the capabilities of your printer.
There is also something called Aspect Ratio, which is usually expressed in inches x inches such as 6x9 but that doesn't mean the size on the screen or when printed is 6x9. It is the ratio of the pixel dimensions. When cropping your photos, you will have several standard aspect ratios to choose from plus any custom ones you create.
In iPhoto '09, after you choose Print, in the Print Setting window are the settings for the size you want the photo printed. You want to shoose a setting with the same aspect ratio of your photo. Otherwise, iPhoto will resize and/or crop your photo to fit the size you have chosen.

How to change SGA and PGA in 10g r2 RAC

Hi,
How to change SGA and PGA in 10g r2 RAC, its Linux.

Hi,
Here is the way i followed to change SGA and PGA in RAC.
Action Plan to change the memory parameter in the production environment(5/21/2010)
Note:
=====
Practice should be done in the DEV/TST environment before moving to Production;
Although the procedure could be applied in the testing environment the changing values
used in the testing environment should be modified since RAM number are not the
same between the testing servers and production servers.
1.     Make changes to these two parameters in one of
     the prod instance, e.g. PROD1
     ====================================================
     login as sysdba on sqlplus
Change :
alter system set sga_target=28G scope=spfile sid='*';
Change :
alter system set pga_aggregate_target=4G scope =spfile sid='*';
     sql>alter system set pga_aggregate_target=4G scope=both;
     sql>show parameter pga_aggregate_target;
          -- should see the altered number on both instances
Change:
sql>alter system set sga_max_size=28G scope=spfile sid='*';
sql>alter system set sga_max_size=28G scope=spfile ;
sql>alter system set sga_target=28G scope=spfile;
3.     shutdown database PROD (two instances should be shut down)
     $>srvctl stop database -d PROD
     $>. /$ORA_CRS_HOME/bin/crs_stat -- to check for the database status
4.     bring up database PROD (two instance should be brought up)
     $>srvctl START database -d PROD
     $>. /$ORA_CRS_HOME/bin/crs_stat -- to check for the database status
     login into both instances as sysdba to check
     sql>show parameter pga_aggregate_target
     sql>show parameter sga_max_size
          -- should see the altered number still there in both instances
          -- from step 1
     -- After confirming above two parameters are altered on both instances,
     -- then issue the syntax below in one instance
5)     check everything is ok

I just purchased brad paisley hit album and two songs on play about 15 seconds then change, how can i fix this?

i just purchased brad paisley hit album and two songs on play about 15 seconds then change, how can i fix this?

Assuming you are in a region where you are allowed to redownload your past purchases, delete the current copies from your iTunes library, go to the iTunes Store home page, click the Purchased link from the Quick Links section in the right-hand column, then select Music and Not on this computer. You should find download links for your tracks there.
If the problem persists, or that facility is not yet available in your region, contact the iTunes Store support staff through the report a problem links in your account history, or via Contact Support.
tt2

How can change background color of drop down menu navigation?

Hi,
I am using multi level drop-down-navigation menu in my website.
I am get good drop-down menu from htmldrive.net, but problem is how can change menu background color black to other colors.
please help me
Link & code is given below
http://www.htmldrive.net/items/demo/913/Multi-Level-Drop-Down-Menu-Navigation-with-CSS3
HTML Code
<div id="nav">
<ul>
<li><a href="#">Home</a></li>
<li><a href="#">About Us</a></li>
<li><a href="#">Our Portfolio</a></li>
<li><a href="#">One Dropdown</a>
        <ul>
        <li><a href="#">Level 2.1</a></li>
        <li><a href="#">Level 2.2</a></li>
        <li><a href="#">Level 2.3</a></li>
        <li><a href="#">Level 2.4</a></li>
        <li><a href="#">Level 2.5</a></li>
        </ul>
</li>
<li><a href="#">Three Levels</a>
        <ul>
        <li><a href="#">Level 2.1</a></li>
        <li><a href="#">Level 2.2</a></li>
        <li><a href="#">Level 2.3</a>
                <ul>
                <li><a href="#">Level 2.3.1</a></li>
                <li><a href="#">Level 2.3.2</a></li>
                <li><a href="#">Level 2.3.3</a></li>
                <li><a href="#">Level 2.3.4</a></li>
                <li><a href="#">Level 2.3.5</a></li>
                <li><a href="#">Level 2.3.6</a></li>
                <li><a href="#">Level 2.3.7</a></li>
                </ul>
        </li>
        <li><a href="#">Level 2.4</a></li>
        <li><a href="#">Level 2.5</a></li>
        </ul>
</li>
<li><a href="#">Services</a></li>
<li><a href="#">Contact Us</a></li>
</ul>
</div>
CSS CODE
#nav {
        float: left;
        font: bold 12px Arial, Helvetica, Sans-serif;
        border: 1px solid #121314;
        border-top: 1px solid #2b2e30;
        -webkit-border-radius: 5px;
        -moz-border-radius: 5px;
        border-radius: 5px;
        overflow: hidden;
#nav ul {
        margin:0;
        padding:0;
        list-style:none;
#nav ul li {
        float:left;
#nav ul li a {
        float: left;
        color:#d4d4d4;
        padding: 10px 20px;
        text-decoration:none;
        background:#3C4042;
        background: -webkit-gradient( linear, left bottom, left top, color-stop(0.09, rgb(59,63,65)), color-stop(0.55, rgb(72,76,77)), color-stop(0.78, rgb(75,77,77)) );
        background: -moz-linear-gradient( center bottom, rgb(59,63,65) 9%, rgb(72,76,77) 55%, rgb(75,77,77) 78% );
        background: -o-linear-gradient( center bottom, rgb(59,63,65) 9%, rgb(72,76,77) 55%, rgb(75,77,77) 78% );
        box-shadow: 0 1px 0 rgba(255, 255, 255, 0.1) inset, 0 0 5px rgba(0, 0, 0, 0.1) inset;
        border-left: 1px solid rgba(255, 255, 255, 0.05);
        border-right: 1px solid rgba(0,0,0,0.2);
        text-shadow: 0 -1px 1px rgba(0, 0, 0, 0.6);
#nav li ul {
        background:#3C4042;
        background-image: -webkit-gradient( linear, left bottom, left top, color-stop(0.09, rgb(77,79,79)), color-stop(0.55, rgb(67,70,71)), color-stop(0.78, rgb(69,70,71)) );
        background-image: -moz-linear-gradient( center bottom, rgb(77,79,79) 9%, rgb(67,70,71) 55%, rgb(69,70,71) 78% );
        background-image: -o-linear-gradient( center bottom, rgb(77,79,79) 9%, rgb(67,70,71) 55%, rgb(69,70,71) 78% );
        border-radius: 0 0 10px 10px;
        -moz-border-radius: 0 0 10px 10px;
        -webkit-border-radius: 0 0 10px 10px;
        left: -999em;
        margin: 35px 0 0;
        position: absolute;
        width: 160px;
        z-index: 9999;
        box-shadow: 0 0 15px rgba(0, 0, 0, 0.4) inset;
        -moz-box-shadow: 0 0 15px rgba(0, 0, 0, 0.4) inset;
        -webkit-box-shadow: 0 0 15px rgba(0, 0, 0, 0.4) inset;
        border: 1px solid rgba(0, 0, 0, 0.5);
#nav li ul a {
        background: none;
        border: 0 none;
        margin-right: 0;
        width: 120px;
        box-shadow: none;
        -moz-box-shadow: none;
        -webkit-box-shadow: none;
        border-bottom: 1px solid transparent;
        border-top: 1px solid transparent;

Change this:
.ddsmoothmenu{
font: bold 12px Verdana;
background: #414141; /*background of menu bar (default state)*/
width: 100%;
to this:
.ddsmoothmenu{
font: bold 12px Verdana;
background: #new color code;
width: 100%;
And repeat this on other selectors.
Nancy O.

How to Change IP Address in an Oracle 11g Fusion middleware environments

Hi,
We are changing server IP address. Not sure if I need to update any configuration files etc for the new IP address of the host. Can you please help on this
We have following 11g Fusion middleware comonents installed on the server:
Weblogic 10.3.3
SOA Suite 11.1.1.3.0
BPM 11.1.1.3.0
BAM 11.1.1.3.0
WebCenter 11.1.1.3.0
OHS 11.1.1.3.0

>
I've a two node RAC working fine. I want to do an experiment and want to chang the VIP and private IP adresses. I canged the IP addresses in /etc/hosts files on bothe nodes and re-configured the eth1 with new IP addresses. I rebooted the nodes. When I try to start crs, I get error:
>
If you change your VIP to a different subnet, then you have to change your Public IP to the same subnet as well (vice versa)..
You may not have to change your Private IPs (let's say 10.10.10.x) because these are your interconnect addresses and are "private" to the RAC nodes...
You can read on the following Metalink Notes:
>
How to Change Interconnect/Public Interface IP or Subnet in Oracle Clusterware
Doc ID: 283684.1
Modifying the VIP or VIP Hostname of a 10g or 11g Oracle Clusterware Node
Doc ID: 276434.1
Considerations when Changing the Database Server Name or IP
Doc ID: 734559.1
Preparing For Changing the IP Addresses Of Oracle Database Servers
Doc ID: 363609.1
The Sqlnet Files That Need To Be Changed/Checked During Ip Address Change Of Database Server
Doc ID: 274476.1
>
Also check my notes about it.. http://karlarao.tiddlyspot.com/#%5B%5BRAC%20Change%20IP%20-%2010gR2%5D%5D
- Karl Arao
http://karlarao.wordpress.com
Edited by: Karl Arao on Apr 14, 2010 2:03 PM

Media key volume control stepper, how to change?

So I just started using kdemod, and I got my multimedia keys working but I'm wondering how to change the volume stepper? Right now it changes the volume by 10% for every step made by my media volume control keys. I would like to have it set to something more sane like 2-3%. Anybody know what I'm talking about or can offer some help? Thanks.

Hi,
"Default value" tab is in Work center. Check for the same in CR02 (Workcenter change view)
In CA02, in Operations Overview, you can change the control key in the routing.
Hope this is clear now..
-Thaila Shree

How to Change IP Address?

Hi,
I've a two node RAC working fine. I want to do an experiment and want to chang the VIP and private IP adresses. I canged the IP addresses in /etc/hosts files on bothe nodes and re-configured the eth1 with new IP addresses. I rebooted the nodes. When I try to start crs, I get error:
CRS-0184: Cannot communicate with the CRS daemon.
My question is that is it possible to change IP address of RAC nodes? If yes then what are the steps?
Thanks.

>
I've a two node RAC working fine. I want to do an experiment and want to chang the VIP and private IP adresses. I canged the IP addresses in /etc/hosts files on bothe nodes and re-configured the eth1 with new IP addresses. I rebooted the nodes. When I try to start crs, I get error:
>
If you change your VIP to a different subnet, then you have to change your Public IP to the same subnet as well (vice versa)..
You may not have to change your Private IPs (let's say 10.10.10.x) because these are your interconnect addresses and are "private" to the RAC nodes...
You can read on the following Metalink Notes:
>
How to Change Interconnect/Public Interface IP or Subnet in Oracle Clusterware
Doc ID: 283684.1
Modifying the VIP or VIP Hostname of a 10g or 11g Oracle Clusterware Node
Doc ID: 276434.1
Considerations when Changing the Database Server Name or IP
Doc ID: 734559.1
Preparing For Changing the IP Addresses Of Oracle Database Servers
Doc ID: 363609.1
The Sqlnet Files That Need To Be Changed/Checked During Ip Address Change Of Database Server
Doc ID: 274476.1
>
Also check my notes about it.. http://karlarao.tiddlyspot.com/#%5B%5BRAC%20Change%20IP%20-%2010gR2%5D%5D
- Karl Arao
http://karlarao.wordpress.com
Edited by: Karl Arao on Apr 14, 2010 2:03 PM

How to change the privacy statement link url

I looked into the previous threads , could not find the answer to "Changing the privacy statement url to clients privacy statement url".
I am talking about the privacy statement URL in the page that user see it as soon as user logs into the e-business suite.
I have read the previous theads and developers guide regading how to show or hide this autofooter thing. but could not find any thing about how to change the one in the login page.I even looked ino personalization but could not find a place to change this url. please HELP.
Another question is " is it ok to show privacy statement in just the first page and hide it in rest of the application pages?"
Thanks
karan

Extract from Personalization Guide - Page Footer - Personalization Considerations
* If you wish to personalize the URL that points to the Privacy Statement for a page that displays a standard Copyright and Privacy (that is, its Auto Footer property is set to true), set the Scope to OA Footer, in the Choose Personalization Context page of the Personalization UI.
* If you wish to personalize the URL that points to the Privacy Statement for a page that displays a custom Copyright and Privacy (that is, its Auto Footer property is set to false), set the Scope to Page in the Choose Personalization Context page of the Personalization UI. In the following Page Hierarchy Personalization page , identify and personalize the Privacy page element.

Email messages now show "To: me" instead of the name or email address and I want to know how to change back to the way it was.

I use several yahoo email addresses and it has always been very convienent to see if it is a personal or business related message by simply seeing the To: line. Now all of sudden all I see is "me" and it is not at all helpful. I didn't make the change nor authorize it to be done. I am not even sure if this is a Firefox issue or a Yahoo issue. I would like to know how to change back to show the full email name or address.

hello shackiraq, you'd have to contact yahoo's support about this issue - firefox doesn't handle your emails but just renders a website like it is provided to you by the server of a webmail service.
https://help.yahoo.com/kb/mail-for-desktop

How to change text in PDF doc. which is a musical score

Hello,
I'm new here, so please excuse me if I do or say something I shouldn't.
I need to change the words in a musical score because the font is too small. OCR recognition doesn"t work because there are illustrations that are different from images or text... Is there a way to get in there and make the changes I need to do?
Any help greatly appreciated.

Thanks for the reply, but I have Adobe Reader 9 Pro. Will it still not
work ?
Le 29 sept. 2011 à 29 sept. 11 - 16:09, Claudio González a écrit :
Re: How to change text in PDF doc. which is a musical score
created by Claudio González in Adobe Reader - View the full discussion
Unfortunately, not with the free Reader.
Replies to this message go to everyone subscribed to this thread,
not directly to the person who posted the message. To post a reply,
either reply to this email or visit the message page: [http://forums.adobe.com/message/3944833#3944833
To unsubscribe from this thread, please visit the message page at [http://forums.adobe.com/message/3944833#3944833
]. In the Actions box on the right, click the Stop Email
Notifications link.
Start a new discussion in Adobe Reader by email or at Adobe Forums
For more information about maintaining your forum email
notifications please go to http://forums.adobe.com/message/2936746#2936746

About RAC how to change san

Similar Messages

Maybe you are looking for