About the output of "show dot11 associations" command.
Hello.
I have been made to the research of IP Phone 9971 . (Used by Wireless)
The schematic diagram is shown below.
CUCM
|
L3-SW
|
AP 1142 (FW:15.2(2)JB)
|
CP-9971 (FW:9.3(2))
The results of the "show dot11 associations" command are output as follows.
ap#show dot11 associations
802.11 Client Stations on Dot11Radio0:
SSID [XXXXXX]:
MAC Address IP Address Device Name Parent State
0026.cba3.0b9f 10.10.60.12 CP-7925 SEP0026CBA30B9F self Assoc <-----Here!
f0b4.799f.a9a4 10.10.60.10 unknown - self Assoc
ap#
I'm using the IP Phone 9971 (not CP-7925).
But the output of "show dot11 associations" command, has become "CP-7925" on Device.
What Is this by Design? Will it bug or?
Thank you very much in advance.
Shigeru Kubota
Hi, Kayle
Thanks a lot for replay.
I am using an autonomous access point.(AP 1142)
Device firmware is the latest version.
(AP 1142 : 15.2(2)JB , CP-9971 : 9.3(2))
As with you, I'm guessing that the access point does not recognize the CP-9971 device, too.
I'll try to contact the TAC.
Thank you for your support.
Best regards,
Shigeru Kubota
Similar Messages
-
CBWFQ: Question about the output of "show policy-map interface" command
Hi everyone,
I have a question about the output of "show policy-map interface" command.
The following is the output of this command and lower side of the output shows
(total queued/total drops/no-buffer drops) 0/342/0
If the packets drop occur due to the situation of no enough buffer,
"no-buffer drops" counted up. But "no-buffer drops" has not been counted up.
The "no-buffer drops" is 0 (zero) but "total drops" are counted as 342.
I guess there are other factors except "no-buffer drops" to add "total drops".
But I can not find any information about "other factors".
So I would like to know the "other factors" added to "total drops".
reserch-3725#sh policy-map interface fastethernet0/1
FastEthernet0/1
Service-policy output: shaping
Class-map: kdpc (match-all)
146956873 packets, 115209221595 bytes
5 minute offered rate 156000 bps, drop rate 0 bps
Match: access-group name YOKOHAMA_to_CHINO
Traffic Shaping
Target/Average Byte Sustain Excess Interval Increment
Rate Limit bits/int bits/int (ms) (bytes)
9360000/9360000 58500 234000 234000 25 29250
Adapt Queue Packets Bytes Packets Bytes Shaping
Active Depth Delayed Delayed Active
- 0 146956724 3539850811 2960247 3851843541 no
Class-map: class-default (match-any)
552458414 packets, 249687580329 bytes
5 minute offered rate 242000 bps, drop rate 0 bps
Match: any
Traffic Shaping
Target/Average Byte Sustain Excess Interval Increment
Rate Limit bits/int bits/int (ms) (bytes)
3072000/3072000 19200 76800 76800 25 9600
Adapt Queue Packets Bytes Packets Bytes Shaping
Active Depth Delayed Delayed Active
- 0 552453209 573909865 30358216 2926188156 no
Service-policy : policy1
Class-map: dlsw (match-all)
979578 packets, 264843255 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: access-group name acl-dlsw
Queueing
Output Queue: Conversation 137
Bandwidth 128 (kbps) Max Threshold 64 (packets)
(pkts matched/bytes matched) 20922/17371500
(depth/total drops/no-buffer drops) 0/0/0
Class-map: telnet (match-all)
29938 packets, 1806058 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: access-group name acl-telnet
Queueing
Output Queue: Conversation 138
Bandwidth 64 (kbps) Max Threshold 64 (packets)
(pkts matched/bytes matched) 639/38900
(depth/total drops/no-buffer drops) 0/0/0
Class-map: class-default (match-any)
551448911 packets, 249420939729 bytes
5 minute offered rate 242000 bps, drop rate 0 bps
Match: any
Queueing
Flow Based Fair Queueing
Maximum Number of Hashed Queues 128
(total queued/total drops/no-buffer drops) 0/342/0
Your information would be appreciated.Details infomatiuon regarding show policy-map interface
http://www.cisco.com/en/US/tech/tk543/tk545/technologies_tech_note09186a008010dd6a.shtml
http://www.cisco.com/en/US/tech/tk543/tk760/technologies_tech_note09186a0080108e2d.shtml
http://www.cisco.com/univercd/cc/td/doc/product/software/ios123/123cgcr/qos_r/qos_s2g.htm#wp1146884 -
Confused about output of show vlan id command
I configured a few vlans on a switch. 3 vlans, each assigned only one port. The ouput of show vlan brief shows me exactly what I would expect:
IOU1#show vlan bri
VLAN Name Status Ports
1 default active Et0/0, Et0/3, Et1/3
101 VLAN0101 active Et1/0
102 VLAN0102 active Et1/1
103 VLAN0103 active Et1/2
1002 fddi-default act/unsup
1003 token-ring-default act/unsup
1004 fddinet-default act/unsup
1005 trnet-default act/unsup
But confusingly when I do a show vlan id for one of my vlans it lists the vlan's interface and then two other interfaces:
IOU1#show vlan id 102
VLAN Name Status Ports
102 VLAN0102 active Et0/1, Et0/2, Et1/1
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
102 enet 100102 1500 - - - - - 0 0
Primary Secondary Type Ports
Et0/1 and Et0/2 are trunks to two other switches. I don't get why its listing those trunk ports though I was only expecting it to show Et1/1. Is listing those ports there because this vlan is connected via trunk ports to other switches? I don't know exactly what those two interfaces there is telling me.I think IOU and IOL behave this way. When you say real switch, on nexus platforms in my experience they are same as what you have shown above as IOU.
A switch like C3750, C3560, C3650, C3850 etc.... they will have regular output that you might be used to, i.e. not showing trunk interfaces in the vlan id output.
Hope this helps. -
How to read the output of 'tarantella license query' command?
I'm trying to track my license usage (to better determine when to buy new licenses, and to track usage over time).
When I issue the 'tarantella license query command, this is typical of the output I see:
[root@sgdserver ~]# /opt/tarantella/bin/tarantella license query
License usage at: Mon Feb 11 14:03:53 EST 2008
Type In use / Total
Base 6 / 230
UNIX 4 / 230
Mainframe 0 / 230
Windows 0 / 230
AS/400 0 / 230
[root@sgdserver ~]#What is the above saying? Is it saying that I am using 10 licenses out of my 230, or am I just using 6 licenses? In other words, do I add up the numbers or just use the highest one? Or do I just have to worry about the 'Base' license number?
Thanks.The base license is the number of users that are logged into a webtop.
From there you count then connectivity type.
So you have 6 webtop licenses out of 230 consumed and of those 4 users have launched UNIX sessions out of 230 you have licensed.
hope this helps. -
Q. about the images that show in a file's preview
Can I change the image that shows in a file's Alias (is that the right term?) ? Let me tell you a bit more about what I mean... I have 2 aliases for 2 files in use at the mo' - 1 is a tiff, created and saved by Grab. At the moment the picture that shows on the file, unopened, on my desktop, is the generic image that shows a tiny photograph and the text "TIFF" underneath - it'd be cool if it were a tiny preview of the grabbed image instead.
Second, I dragged the file containing my camera owners manual to the file-and-folder part of the dock, on the right-hand end, thus creating an alias, I think. Again, the image showing on the alias on the dock is the generic pdf image - same as the tiff but with the text "pdf" instead of "tiff". If I go to the actual file, as opposed to the alias in the dock, and choose Get Info, the Preview is indeed the manual's cover. Again it'd be cool if the image showed a tiny version of the owners manual cover. - I 've got 2 pdf files next to each other on the dock, and it'd be cool to see which was which at a glance. If I open the respective files Info., the correct previews show in the Preview section, so why don't they show in the circumstances I describe above?
Any ideas, folks?The Dock does not show an icon preview, unless the file has an icon made for it.
For example, if you open the pdf in preview and do a screen capture, cmd-ctrl-shift-4, select the entire first page. You can then Get Info on the pdf in the finder and paste that picture into the icon of the file. When you drag it to the Dock, it will show with the picture as the icon.
In the Finder, under View Options, you can have it show icon previews. Not only can you see the first page of a pdf, you can actually thumb through the pages. However, if you've set an icon, that will be shown as the preview without the ability to thumb through. -
TWO Questions about the new TV shows rental with iTunes and Old Apple TV
Hello all. Been trying to find some FAQs or something but think only got partial answers, so I hope I can get some here, using 'Glee' as an example:
1. Can the (old) Apple TV rent new TV shows available? E.G. Glee Season 2?
2. If I use iTunes 10 to rent an episode (of Glee HD), can I play it on my TV via my (old) Apple TV? Like in the form some kind of streaming?
Thanks and cheersYou may be right, I'm just thinking there is no movie rental "movie menu" option on the current Apple tv either, but one can still rent movies.
Unless the tv show downloads are specifically designed to block usage on certain devices or there is something different about them, I would have thought that tv show rentals could be enabled at the itms end by adding a rental option on the specific tv show page, just as movies are done now.
If I were in the US, I probably wouldn't be holding my breathe for tv show rentals but I'm not convinced I'd rule them out either. -
I need to provide the output for one 3750x switch out of a cluster of 7.
With all of the various stats, the entire log will be fairly large.From the master switch open a session to that switch and than run "sh tech-support"
session 7
sh tech
HTH -
My wife's 4s needed to update the software. when it was updated/downlaoded the Wi-Fi would not work. It is currently grayed out and under General, About: the Wi-Fi is N/A. Does anyone have a suggestion to correct. I called Apple support and they felt it was the software update because it worked prior to the update however they wanted to charge 19.95 to assist. Thank you all.
If it is a hardware issue, then you don't get charged the $19. But, if it turns out to be a setting you messed up, then YES, they will want to charge you $19 to help you learn how to use your phone after your 90-days of FREE phone support expired. Or you could read the manual or articles that are available for free online.
Basically, if you want someone to hold your hand, then you'll pay for it.
However.... having said all of that, try this article: http://support.apple.com/kb/ts1559 -
Hi all,
Can somebody ,please, clarify for me what the command "show dot11 statistics client-traffic" shows to me? The output usually looks like:
xxxx.xxxx.xxx pak in 24289 bytes in 5050182 pak out 32230 bytes out 35936358
dup 47 decrpyt err 0 mic mismatch 0 mic miss 0
tx retries 3455 data retries 3455 rts retries 0
signal strength 62 signal quality N/A
But is the units for signal strength are dBm or mW? And why the quality is N/A? What values are better ? 60 or 19 (for strength)? So if anybody can provide me with an explanation for the last 2 lines it would be great. By the way, do you know where on Cisco.com all the "show dot11" commands get explained?
Cause, additional hard to understood output is "show dot11 associations" shows MACs "not related to any ssid" (how can it be in the first place?) or shows MACs which are do associated to (the only) broadcasted SSID but the IP is 0.0.0.0? Why and what does it mean?
Thanks in advance,
Alex.First of all thank you for answering my question. On the other hand, look - this was the first place for me to go on Cisco.com. Unfortunately (and this is the very problem itself), for some odd and mysterious reasons there is no clear explanation for those commands on this or any other page on Cisco.com. In fact, the only (!) explanation for "show dot11 statistics client-traffic" is "Use the show dot 11 statistics client-traffic privileged EXEC command to display the radio client traffic statistics".
No single word about the output and it interpretation. That's strange as its sounds.
The same goes for why there are Macs which are "not associated to any SSID" in "show dot11 associations".
So, if anybody knows the answer for the previously posted questions - please post the answers. For my opinion it would be interesting for the whole community. -
Cannot read the output from windows command.
Hello
I have the following classes
package cmd;
import java.io.IOException;
public class CMD {
public CMD(){
ProcessBuilder pb = new ProcessBuilder()
.command("cmd.exe","/c","del *.*")
.redirectErrorStream(false);
Process p;
try {
p = pb.start();
StreamGobbler errorGobbler = new StreamGobbler(p.getErrorStream(), "ERROR");
// any output?
StreamGobbler outputGobbler = new StreamGobbler(p.getInputStream(), "OUTPUT");
// start gobblers
outputGobbler.start();
errorGobbler.start();
} catch (IOException e) {
// TODO Auto-generated catch block
System.out.println("eee "+e.getMessage());;
public static void main(String[] args) {
System.out.println("x");
new CMD();
System.out.println("x");
and
package cmd;
import java.io.BufferedReader;
import java.io.IOException;
import java.io.InputStream;
import java.io.InputStreamReader;
public class StreamGobbler extends Thread {
InputStream is;
String type;
StreamGobbler(InputStream is, String type) {
this.is = is;
this.type = type;
@Override
public void run() {
try {
InputStreamReader isr = new InputStreamReader(is);
BufferedReader br = new BufferedReader(isr);
String line = null;
while ((line = br.readLine()) != null)
System.out.println(type + "> " + line);
catch (IOException ioe) {
ioe.printStackTrace();
Please note that I cannot seee the output from wndows command : del *.* and the java class execution does not finished.
I I will replace the above command with the dir command then the output of the command is visible.
Would you give me a hint about how to modify the above clases in order to parse the output of the del *.* ?
Please note that the above example is important because I am developping a tool and it is mandatory for that tool to parse the output from a windows batch command.
Best regards,Please note that I cannot seee the output from wndows command : del *.* and the java class execution does not finished.
I I will replace the above command with the dir command then the output of the command is visible.
Would you give me a hint about how to modify the above clases in order to parse the output of the del *.* ?
No - but I will give you a hint about ProcessBuilder and how to develop software properly.
Hint #1: Don't try to automate something that you don't know, or understand, how to do manually.
a. Do you know how to execute 'del *.*' manually in a command window?
b. Did you try that manually to see what happens?
My guess is 'no'. If you had you would know that the response to a 'del *.*' command is going to be this:
Are you sure (Y/N)?
And your 'java class execution' doesn't finish because the 'del' command is waiting for you to answer that question.
Hint #2: Don't try to use ProcessBuilder for an application that requires console input unless you first know how to provide that console input via your Java code.
Your code will wait forever since it does NOT answer that question.
Search the net and The Java Tutorials and you can find examples of executing command line utilities. Then try those examples first and make sure that:
1. They work for you
2. You understand HOW they work
Then you can modify those examples to do what you want to do. -
About 'show ip routes' command on Content Engine
Hello!
I have a question.
CE has only one default static route configured, however the output below show that it has 361 cached routes:
#sh ip routes
Destination Gateway Netmask
Number of route cache entries: 361
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
What does it mean?
ACNS version 5.3.7
The official documentation is silent in this case.
Thank you.it's the same as the old version of ip route caching in IOS in the old days.
When the router had to go a routing decision it would cache it for later to speed up routing.
This is the same here.
The CE will cache any recent route lookup decision it had to take.
Gilles. -
ACE Sticky Connections, Show Conn Output and Show serverfarm
Hi Community,
I'm deploying a Cisco ACE module and I have some questions about sticky connections and about the output of the show conn command and show serverfarm command.
I have the follwoing configuration:
rserver host srv_1 ip address 10.4.11.14 inservicerserver host srv_2 ip address 10.4.11.18 inserviceserverfarm host farm_144 rserver srv_1 144 weight 1 inservice rserver srv_2 144 weight 3 inservice
sticky ip-netmask 255.255.255.255 address source st_host144
timeout 10080
serverfarm farm_144
class-map match-all vip_144
2 match virtual-address 10.4.11.208 tcp eq 143
policy-map type loadbalance first-match lb_144
class class-default
policy-map multi-match policy_vip_webcache
class vip_webcache_144
loadbalance vip inservice
loadbalance policy lb_144
loadbalance vip icmp-reply active
nat dynamic 411 vlan 411
We can assume that service policy was applied at the interface vlan. So, let's go to the questions:
1- If sticky is enabled the output command "show conn" should show just one entry by ip address?
The real output is:
DC01-ACE-01-PRIMARY-SW1/context_servidores# show conn | inc :143333046 1 in TCP 411 10.2.158.87:3616 10.4.11.208:143 ESTAB 286390 3 in TCP 411 10.2.158.87:3562 10.4.11.208:143 ESTAB310233 1 in TCP 411 10.1.5.87:3424 10.4.11.208:143 ESTAB
Look that the ip address 10.2.158.87 is shown 2 times. In same times, the same ip address is shown 4 times to the same VIP and the same port. Is it a normal behavior?
2- According to the configuration, the srv_2 has weight 3 and srv_1 has weigth 1, but the output of show serverfarm show somethin strange:
DC01-ACE-01-PRIMARY-SW1/context_servidores# show serverfarm farm_144 serverfarm : farm_144, type: HOST total rservers : 2 state : ACTIVE DWS state : DISABLED --------------------------------- ----------connections----------- real weight state current total failures ---+---------------------+------+------------+----------+----------+--------- rserver: srv_1 10.4.11.14:144 1 OPERATIONAL 11 386 0 rserver: srv_2 10.4.11.18:144 3 OPERATIONAL 35 66 0
We can see that the weight is working good, but the total of connections is higher at srv_1 than srv_2. Why?
Somebody can help me to understand better this problem of if its a normal behavior?
Thanks in advance!!Hi Gaurav,
About question 1, I got some informations too. It's perfectly normal the client open 2 or more connections at the same time. The client's application is the responsable. We removed the ACE and put the client directly to the server and the result of the total connections opened was the same.
About question 2, I made some "clears" on the serverfarm, the sticky database and after that, the numbers were more real.
DC01-ACE-02-SECONDARY-SW1/context_servidores# sh serverfarm farm_webcache_144
serverfarm : farm_webcache_144, type: HOST
total rservers : 2
state : ACTIVE
DWS state : DISABLED
----------connections-----------
real weight state current total failures
---+---------------------+------+------------+----------+----------+---------
rserver: srv_webcache_1
10.4.11.14:144 1 OPERATIONAL 1025 15499 4436
rserver: srv_webcache_2
10.4.11.18:144 2 OPERATIONAL 1794 33471 471
DC01-ACE-02-SECONDARY-SW1/context_servidores#
Anyway thank you very much for your feedback.
Plínio Monteiro -
About the interface web oracle database express edition
Hi
I want execute a export from web interface I click on link "data" I choose the object table and after I click on link "download" but the file export at format csv contain only the lines which I see on the interface web .
is it possible to export all rows of the table object in CSV file ?
thinkThere are many ways to skin that cat, i.e. just using sqlplus and spooling to a file:
set pagesize 0 verify off feedback off linesize 500 trimspool on
spool filename.csv
select <col1> || ',' || <col2>[|| ','||<colN>] as csvout from <table>;
spool off
If there are date (or any of the timestamp) datatypes you'll want to be specific about the output format, i.e. use to_char( <col>, 'yyyymmdd hh24:mi:ss')...
Also may want to have [var]char column values wrapped in single quotes, just add them in- i.e. ...''''||<col>||'''' it takes two single quotes inside a literal to get one in the output.
There will still be some stuff in the spool file needing cleanup, like the 'spool off' command and an echo of the SQL if you're running sqlplus interactively, don't think there's any way to turn off that echo. 'set echo off' doesn't do it as one would think.
Edited by: clcarter on Oct 31, 2012 10:31 AM
nix the headings comment -
Hi everyone in the forum,
I do not know if i should post this question here, but i think is the best place. Sorry if i were wrong.
just a question because i have no idea how to format the output i need.
I have a REAL or FLOAT and the output restrictions shows that it should be:
1.0000 D-08 if the value is less than 1
1.0000 if the value is [1,9]
1.0000 D+03 is value bigger than 9
and the other problem is whith other variable (type String) which represents integers, e.g, 0.000000 1.0000000 2.000000; and i have to return only 0 1 2 .
Any suggestion about how to format the output?
ThanksDecimalFormat
-
Hi all
when i run my request using XML Report Publisher .request completes without error.
but when i see the output it shows me a message dialogue box saying
File does not degin with '%PDF-'
though my template is of rtf type.
any idea
pls helpWhat is the Output type of the concurrent program ?
check if that is PDF?
Maybe you are looking for
-
How to install Photoshop 5 in Windows 7 64 bit machine
My Windows XP laptop quit. New laptop is Windows 7 64 bit machine. When I install Photoshop CD and select Install Photoshop 5, nothing happens. I found this link: http://www.adobe.com/support/downloads/detail.jsp?ftpID=5162 but I cannot open it.
-
I cant open itunes or quicktime... i need help
i just downloaded itunes and quicktime and whenever i want to use itunes or quicktime it wont open, what should i do hp Windows XP
-
Hi , We are getting an error in FF_5 while we are uploading the bank statement in MT940 format. The error says that the records " 60 and 62F " are missing. However, when we upload the same file in Production by selecting the same MT940 with field 86
-
Hi Can any one explain the difference between Reset (FBRA) and Reversal (FB08) process. And is there any process like Mass reset , like Mass reversal (F.80)?If yes, what is the T-Code for it, please explain the process. Thanks in advance.
-
Hi all, I have requirement to increase the given date for 3 months(ie., 01-jan-2011, 01-apr-2011,etc) that should be handled in RTF Template. can anyone help me in giving date function for increasing the date. Regards, Vinoth.