About WLC 5508 version 6.0 upgrade to 7.0 issue

hi guys,
I have tow WLC , version is 6.0
One of the WLC successful upgrade and after rebooting the normal
the another WLC successful too , but after rebooting the system version or 6.0
Thanks in advance

Hi,
it seems the one that shows 6.0 was not successfully upgraded. give it another round.
Rating useful replies is more useful than saying "Thank you"

Similar Messages

  • 2 Cisco WLC 5508 controllers and software upgrade 7.6.130 + FUS 1.9

    Hi
    I have two WLC 5508 controllers that need 7.6.130 and FUS 1.9 installed. (Current version 7.3 and FUS 1.7)
    Configuration: One controller is at Site A and the other controller is at Site B (two different states..)
    They're configured so that if Site A goes down, Site A AP's will failover to Site B and vice versa ..
    - What would be the recommended approach for upgrading the software to 7.6.130.0 (from 7.3) and also upgrading FUS 1.9 (from 1.7)?
    My plan was to download 7.6.130.0 to both controllers and pre-download the software to all AP's (about 100 total between both sites) and then reboot the controllers at night at the same time? Or one before the other? 
    Step 2. Install FUS 1.9 to each controller.
    I'm concerned over what might happen during the upgrade and AP failover etc..
    Thanks

    This is what I would do:
    Upload v7.6.130.0 to all WLCs and then use the pre image download to push the image to all access points. 
    Dont reboot the wlc
    Image swap in the access points so that v7.6.130.0 is primary
    Move all access point to one of the WLCs (A)
    Enable ap AAA authentication on the WLC that has no access points and the one you will work on first.  This prevents access points from joining  
    Reboot the WLC (A)
    Upload the FUS 1.9.0.0
    Reboot WLC (A) this takes up to 45 minutes
    When the WLC (A) comes back online, uncheck ap AAA authentication
    Move access points from WLC (B) to WLC (A)
    Enable ap  AAA authentication on  WLC (B)
    Perform all the other task you did earlier on WLC (A)
    That's it.
    -Scott

  • 7925 Phones voice quality issues with wlc 5508 version 7.6

    Hi all,
    I have a mix environment with 1 WLC 5508  and more or less 6 sites with several Access Points ( all AIR-LAP1242AG and all in FlexConnect mode  Hreap ) and several wireless phones (all  CP7925G) . My Ap's have antennas 2.4GHz in all sites except 1 site ( the one i'm talking for now) with 2.4GHz and 5GHz , because of the problems we suggest to have all phone in A BAND (5Ghz) . In this site we force the phones just to A (802.11a only) , power safe NONE , Continuous scan mode , i fallow all in http://www.cisco.com/en/US/docs/voice_ip_comm/cuipph/7925g/7_0/english/deployment/guide/7925dply.pdf , one thing i didn’t do it was apply QoS because I can’t apply several ios commands in that 2960 with lan lite ios.
    So I have 3 SSID for data and 2 for VOICE  ( one is common to all environment and supports 2.4 and 5Ghz , and other just to test one site , with only 5Ghz  with “[WPA2][Auth(802.1X + CCKM)][Auth(FT 802.1X)]”, because I read that problem can be phone rooming , and in FlexConnect only have fast-roaming in a CCKM or a PKM  key-management solution , but even like this the problem still exist) .
    I have another sites with phones in 2.4GHz running well and others with problems.
    i read here in forums lots and lots of people with similar problems , i tried several solutions ( WLC  upgrades versions  and phones firmware's , ….  ) tried all my best of solving the problems mas now I’m running without any ideas , i did also some site surveys and detect some interferers that why I change phones to 5Ghz , and I run also WLC Config analyser to help me , but all without good success. Some changes solve temporarily problems , but after some time , people reclaim about problems.
    I can open a TAC case but first I want be sure if did all already.
    Can someone try to help me?
    ip phone 7925G firmware : CP7925G-1.4.5SR1.3      
    CUCM 8.6.2
    WLC    5508 : 7.6.120.0
    AP : AIR-LAP1242AG-E-K9    7.6.120.0       (flexconnect)
    Best Regards

    Hi Serge,
    Thanks for the suggestions. I have taken care of all the settings. Problem is , the user is seated in his office cabin and using the 7925 and there is around 50db signal strength in his room from an AP which is just outside the cabin. And this doesnt occur often, when we go to check and make calls, everything is fine whereas the user says it happens sometimes in the morning, evening etc... randomly... where the fone goes blank while in a call.... since the problem never happens when we go to troubleshoot the issue, we really dont know what is going on. This is happening when calling PSTN.
    AP's are not restarting and there is no logs indicating that. Wireless infrastructure looks very much OK cos there are other users who are not experiencing this problem and there is ample coverage all over the floor. I am baffled why only one user has this problem even when he is seated in his office cabin.
    Tried changing phones also, but still remains.
    Question  : i tried to do a linktest from WLC to his phone, but it failed, while linktest to laptops are working fine. Does wlc linktest not working for wireless phones ?
    regards
    Joe

  • WLC 5508 reboots itself after upgrading to 7.5.102.0

    Hello all.
    We have two WLC 5508 and we upgraded both to software release 7.5.102.0 two weeks ago. We also upgrade the FUS to version 1.7.
    Since then both WLC reboot randomly once or twice a day with no obvious reason.
    Is anyone else facing the same issue?
    Many thanks.

    Ok, in that case it is very difficult to pin-point the cause for these sorts reboots. It may be due to a unknown bug. Go through below 7.5.102.0 release notes and see any unresolved caveats related to your issue
    http://www.cisco.com/en/US/docs/wireless/controller/release/notes/crn75.html#wp1030058
    Have you configure syslog on your WLC ?  If so see what is the last syslog message sent by WLC before reloading, it may indicate something.
    Do more observation & see whetehr controller reboot every time it hit 1k client limit. Try to narrow down the criteria to identify under what conditions this will trigger.
    In my controller I do not have that many clients & cannot comment if it is related.
    HTH
    Rasika

  • WLC 5508 version 7.3.112.0 : SNMP No Such Instance

    Dear all,
    I've set SNMP community v2c read-only on the controller and then trying to parse a specific OID with a MIB Tool with that community
    but the following OID always returns "No such instance".
    Controller Model : 5508    version 7.3.112.0
    Object
    clsSysApConnectCount
    OID
    1.3.6.1.4.1.9.9.618.1.8.4
    Type
    Unsigned32 
    Permission
    read-only
    Status
    current
    MIB
    CISCO-LWAPP-SYS-MIB ;   -   View Supporting Images
    Description
    "This object specifies the count of AP's that are
    connected with WLC"
    Any solutions ?
    Thanks

    Hi
    Only Cisco TAC can analysis this & tells you exact reason of this reload. It looks like a software related crash..
    I would suggest to move onto a later code (like 7.4.121.0) rather staying in 7.3 code when you get the new hardware.
    HTH
    Rasika
    **** Pls rate all useful responses ****

  • WLC 5508 8.0.100 AP dropout anf fallback issue

    After WLC upgrade to 8.0.100 [ not in HA mode], the AP seem to be dropping out and reconnect using the fallback to IP-  inspite of the statically configured IP on the AP
    Running Outdoor mesh AIR-CAP1552E-N-K9 on WLC 5508
    (Cisco Controller) >show boot
    Primary Boot Image............................... 8.0.100.0 (default) (active)
    Backup Boot Image................................ 7.6.101.2
    =========
    Last AP disconnect details
    - Reason for last AP connection failure.................... The AP has been reset by the controller
    - Last AP disconnect reason................................ Unknown failure reason
    Last join error summary
    - Type of error that occurred last......................... Lwapp join request rejected
    - Reason for error that occurred last...................... No Mwar payload found in join request
    - Time at which the last join error occurred............... Dec 03 00:05:26.114
    AP disconnect details
    - Reason for last AP connection failure.................... The AP has been reset by the controller

    We downgraded the WLC to  7.4.121.0 and finally got rid of the DHCP problem
    But encountered a new issue
    The WGB once connected to the mesh AP does not reconnect to the network  , auth failure-   AIR-SAP1602E-Z-K9 running  - ap1g2-k9w7-mx.152-2.JB2
    Local EAP auth configured for WGB client on the WLC
    Looks more like the WGB stuck in a state , unable to negotiate its credentials
    Controller log
    *dot1xMsgTask: Mar 24 10:33:52.737: #DOT1X-3-WPA_SEND_STATE_ERR: 1x_kxsm.c:1404 Unable to send EAPOL-key msg  - invalid WPA state (0) - client f4:0f:1b:23:03:37
    Attached is the debug and client status from WLC
    Any  idea what is going on
    Thanks

  • WLC 5508 AP SSO FUS Upgrade with different Versions

    Hi everybody,
    I've got two 5508 configured as AP SSO and I want to upgrade the FUS to 1.9.0.0
    The Image running is 7.6.110.0
    On the active controller the FUS Version is 1.3
    On the HA-SKU controller the FUS Version is 1.7
    Now, can I upgrade the FUS to 1.9.0.0 using the GUI, even when both controllers don't use the same FUS Version? If yes, can I go directly from FUS 1.3 to 1.9.0.0?
    thanks a lot,
    marc

    Unfortunately its not possible to upgrade just the standby controller in a AP SSO setup. The Command "transfer" is not available on the controller with the standby role. :-/
    I don't get it, why it's not possible to upgrade either FUS oder Software in a AP SSO setup without downtime. The reason why people use AP SSO is because they have a sensitive wireless environment (24/7) and care about not having some downtime. Hopefully there will give some improvements in future releases in case of downtimes when upgrading.

  • Wlc 5508 inaccessible after upgrade to version 8

    dear all,
    I have a problem after upgrading wlc 5508, 
    at first after upgrade everything works fine, but while waiting for APs to rejoin, wlc suddenly inaccessible either via SSH, telnet or console
    I have restart the wlc with no luck
    LED indicator for SYS and ALR are off
    any suggestion will be highly appreciated
    thanks
    regards

    If the appliance failed in the first month after delivery, you might be able to squeeze off an RMA. 
    If the appliance failed in the first year after delivery, I don't care what is written in the "warranty", you can't do anything until you have a valid Service Contract.

  • WLC 5508, vlan select, reserved address in external DHCP server

    Hi guys,
    I have a deploy with a WLC 5508 version 7.0.116.0, APs mode local and vlan select feature enable. The issue is that the reserved IP address in external DHCP server not work. The DHCP contains a reserved IP address associates with mac address, but the assignement of IP is not match with de policies in DHCP. All others services operate normally.
    This reserved assignment operate previusly to modificate the WLAN to vlan select feature. Help me to improve this situation.
    Thanks.-
    Best regards

    Hello Abhishek, thanks for you quick answer....
    the link was a document used for the deploy, but not especifict nothing about the reserved IP address for particular host. In other words, the reserved IP address (through MAC address) in external DHCP server not work when "vlan select" its enable.

  • Webauth page on WLC 5508

         Hi ,
    I need to download a login banner page on our WLC 5508 version 7.4.100.60  but i am getting error and the logs is showing the following :
    *TransferTask: Sep 11 11:05:04.248: #CLIWEB-3-BUFFER_TOO_LONG: cli_web_api.c:3240 Buffer for Login Banner too long (max = 1296 chars).
    My FTP is working fine since i have upgraded the version using it and the .tar file which i am trying to upload is 50K  can any body help on this please

    Mohammad,
    Typically, login banners are .txt files.  Please ensure the file that you are uploading is a .txt and not a .tar.
    If you are unsuccessful in uploading the file through the Web GUI, might I suggest that you try it through CLI?  Sometimes transfers just seem to work better through CLI.
    Just in case you have any questions on the CLI transfer, I have this link for your reference:
    www.cisco.com/en/US/docs/wireless/controller/7.0/configuration/guide/c70mfw.html#wp1132285
    This is the Configuration Guide for the WLC.
    Please let me know if this fixes your issue.  If it does, please rate this answer and mark your question as Answered.
    Charles Moreton

  • Unable to upload/download the configuration in WLC 5508

    Dear Friends,
    I do have issue in upgrading firmware or downloading code from WLC 5508 , version 7.0. I did the same image upload with other devices through CLI from my notebook and it works fine.
    Everytime i try to upload/download the image, it gives the error .
    Has anyone faced the issues, is there any workaround ?
    Regards,
    SID

    I believe that is just how Cisco designed it:). I believe in earlier versions this worked.
    I don't like it now because I cant download the config on a wlc of the ap I'm on. The enable managent via wireless is totally different... As you know, you can manage it.... Sort of:)
    Thanks,
    Scott Fella
    Sent from my iPhone

  • MSE NMSP status inactive after WLC 5508 HA failover

    I have a customer who has a Prime Infrastructure 2.0 server and MSE 7.4 server for Context Aware Services.   The MSE also has the AeroScout Tag Engine for Tracking the AeroScout RFID tags it has deployed.    They have a WLC 5508 HA pair running version 7.4 at their main campus, and two other standalone WLC 5508s at 2 other smaller campuses.   The issue they are having is that when a failover of the WLC5508 HA pair occurs at their main campus, they lose tracking of the WiFi and AeroScout clients.   The other WLCs are not affected.
    When this happens, the Prime Infrastructure show the NMSP status of the WLC5508 HA pair as inactive.   The PI gives the message that the time of the WLC is before the MSE.  But the PI, MSE, and WLCs are all synched to the same Campus NTP server, and the time shows the same time down to the second.   I can get the WLC communicating to the MSE again by removing the Assignment of the WLC to the MSE, then re-adding it to the MSE a few minutes later. 
    We are not sure why the WLC 5508 HA pair occasionally fails over to the standby or back to the primary.  We have not seen any cause for the HA pair failover.   Is there something we need to do to the WLC HA pair so that the NMSP still works if a failover of the WLC occurs.  The customer is planning on converting one of their other Standalone WLCs to a HA Pair also.

    That is what I have been doing.  But the problem is that the I have had to do this about 3 times in the last 6 weeks.  Each time correlates with a failover of the WLC 5508 pair.   Will this have to be done each time there is a failover, or is there some setting on the WLCs, MSE, or Prime Infrastructure that can prevent  having manually to un-assign, then re-assign the WLC to the MSE.

  • Cisco WLC 5508 in HA mode error

    Hai ,
    I am Getting the below Error in Cisco WLC 5508, Version 7.4.100.0 in HAmode. The WLC contains Access Points having in local and Flex Connect Mode.
    RF failure notification ErrorType: 32 Reason :Error: Config Sync failed on Standby for the usmdb:HA_send_usmDbApfMsDelete,
    I sam a same bug in Cisco WLC 7.4.100.0 release notes similar to the error like
    RF failure notification ErrorType: 32 Reason :Error: Config Sync failed on Standby for the usmdb:HA_send_usmDbSpamSetRadSlotAntennaType.
    Any Ideas?

    HI Mohamed,
    its a open Caveats  in 7.4.100.0
    CSCud26632
    Symptom: The following SNMP trap appears on the controller when you change the channel width number to 40-MHz:
    RF failure notification ErrorType: 32 Reason :Error: Config Sync failed on Standby for the usmdb:HA_send_usmDbSpamSetRadSlotAntennaType.
    Conditions: Controller is in an HA pair. Join the 802.11n access point to the controller and change the channel width to 40-MHz and channel number to 157.
    Workaround: None
    http://www.cisco.com/en/US/docs/wireless/controller/release/notes/crn74.html
    Reagrds
    Please rate helpful posts

  • WLC 5508 CPU ACL

    Hi, how are you?.  Sorry  by my questions and thanks for the patience.
    I have a doubt. CPU ACL affects only the traffic of the management interface?.
    For example:
    Controller WLC 5508 version 7.0.98.0
    Interface management IP address 186.108.26.2/24
    Interface XX IP address 190.139.109.101
    I have configured the following ACL and applied to CPU ACL:
    (Cisco Controller) >
    (Cisco Controller) >
    (Cisco Controller) >
    (Cisco Controller) >
    (Cisco Controller) >show acl cpu        
    CPU Acl Name................................ ACL
    Wireless Traffic............................ Enabled
    Wired Traffic............................... Enabled
    (Cisco Controller) >show acl summary    
    ACL Counter Status               Enabled
    ACL Name                         Applied
    ACL                              Yes   
    (Cisco Controller) >show acl detailed ACL
                           Source                        Destination                Source Port  Dest Port
    Index  Dir       IP Address/Netmask              IP Address/Netmask        Prot    Range       Range    DSCP  Action      Counter
         1  In         1.1.1.0/255.255.255.0         1.1.1.115/255.255.255.255    6     0-65535   443-443    Any Permit           0
         2 Any         0.0.0.0/0.0.0.0         100.100.100.100/255.255.255.255    6    0-65535   443-443    Any Permit           0
         3 Any         0.0.0.0/0.0.0.0                 0.0.0.0/0.0.0.0          Any     0-65535     0-65535  Any   Deny          51
    DenyCounter : 27
    (Cisco Controller) >
    I have the following doubts
    It is not necessary to allow the ports of tunnel capwap?.
    I have applied this ACL and traffic from Interface XX to 190.139.109.101 is filter.  If I remove CPU ACL traffic to interface XX is permit.  Then CPU ACL affect all interfaces???.

    Hi,
    better a late reply than no reply at all ...
    The CPU ACL actually filters traffic that is destined to one of the WLC ip addresses, so it works on all interfaces, but does not filter all types of traffic. Only traffic that is destined to the WLC itself.
    So if you apply a CPU ACL, it is likely you need to either allow capwap ports or allow everything in the subnet where APs are.
    Regards,
    Nicolas

  • WLC 5508 : session disconnected when one lag-port is down.

    Hello,
    I have a WLC 5508 ( version 6.0.182).
    When the port1 and port2 are connected ( The switch is configured with a etherchannel in forced mode) everything works fine: There is traffic on the 2 ports.
    When I disconnect one of the 2 ports, I can still ping outside with my PC client, but all my tcp sesssions goes down and I even cannot restart my session. The only way I found  is to do a "Disconnect / Reconnect"  on my  PC  wireless connection.
    Do you know this probleme ?
    Is it a way to avoid it ?
    Michel Misonne

    CSCth12513 LAG fail-over does not work on CT5508
    This bug is fixed in the special release available through TAC : 6.0.199.157 and 7.0.xxxx
    Hope this helps.
    Nicolas
    ===
    Dont' forget to rate answers that you find useful

Maybe you are looking for

  • In home agent

    Should I uninstall In Home Agent to avoid getting this worm that it may carry in updates?  Is Verizon doing anything about this problem reported several times on this forum? 

  • Sales and Support for Foreign Countries?

    Although I'm not familiar with the exportability of MATRIXx, I assume foreign sales are permitted (and encouraged). If I work with a foreign customer, to whom in NI should I direct their questions about pricing, planned development, and support? Than

  • The apps wont install in my ipod touch 5th gen

    the apps wont install in my ipod touch 5th gen, it says 'will install' but it wont. i downloaded it through itunes in my pc. and the files doesnt sync. help

  • Yellow printing green, print heads not cleaning and apparent leaking of cartridge

    We have been having problems with the quality of the printing from our printer. We noticed the colour was a bit off and ran a report, we found that the block of yellow that came out (where it tells you the estimated ink levels) was a dark green/grey

  • Dbms_job - Spawns duplicates

    We have created three jobs via dbms_job to run on a daily basis. Initially, everything is fine but after periods of heavy loading we see the number of jobs increasing uncontollably. The same job appears to be resubmitted to the job queue and from a s