AC-1900 "no signal detected" message

Hi, any help greatly recieved, just recieved a new and packaged ac-1900, upon trying to do first boot up procedure all i get is "siganl not detected!" and a flashing cursor in the top left..not sure what to do ....anybody???

Quote from: Stu on 18-May-12, 02:39:57
Take it back and get it exchanged.
Agreed 

Similar Messages

  • MBP connected to Sony LCD 46X350A - No Signal Detected

    Need help.
    I've tried connecting my MBP to my Sony LCD via the VGA output (I believe that's what it is), via the cable supplied when I bought my notebook, but the message on the LCD says no signal detected.
    I've went into the System Preferences, Displays and the MBP definitely recognizes that it is connected to the LCD, but I cannot get any picture (No Signal Detected Message on LCD) either by mirroring or using the LCD as an external monitor.
    Any thoughts or suggestions from anyone?
    Many thanks in advance.

    Im having a very similar issue. I was happily using my MBP with an external Acer Display connected, until that display simply stopped working. It now only says 'No Signal' before shutting off. Zapping the PRAM and the SMC didn't get me anywhere, so I'll be taking it to the Mac Store tonight. I'll post what they'll tell me!

  • HDMI to DVI No Signal Detected

    I have a late 2006 MacBook Pro running OS X 10.6.6. I recently purchased an LG LED-LCD television as well as a HDMI to DVI adaptor cable, both from Amazon (the cable is an Amazon Basics cable). When plugged in to both the laptop and the television, there is no signal detected by the television and no display detected by the laptop. I've tried each of the three HDMI ports on the television, but to no avail. I returned the cable and exchanged it for an identical one, but the problem persists.
    In searching through the forums, I've seen that quite a few people have had issues with this same setup, and I'm wondering if somehow I need more than just the cable to connect to my television (which doesn't make sense, but could still be the case). I've run a diagnostic on my laptop during startup, and found no issues with the hardware, so I'm 99% positive that I don't have a bum DVI port. At this point I'm just not sure what to do to get this to work, so any assistance would be wonderful.

    Sorry for any confusion, my last post was sent before reading your second post.
    The VGA test proves nothing about the DVI output. The DVI ports on these Macbook Pros is a combo DVI and analog VGA port (DVI-A). The DVI-VGA adapter does nothing more than connect the VGA to VGA, and does not convert the DVI to VGA. You have to use an actual DVI device to test the DVI. The 4 pins and large blade on the end of the DVI connector are the VGA pins - they can be omitted on a DVI-HDMI adapter with no harm.
    I really don't know if there could be a problem with the software on the Mac and/or TV, and the cable just fine.
    Perhaps try to seek out someone who has a working DVI-HDMI cable to try? Or try a store that will demonstrate that it works and has a money back guarantee?

  • MSI gtx 770 twinfrozr "no signal detected"

    Hello!
    Just got a new GPU and installed it and all, but when i´m starting my system my monitor doesn´t start and just show a box with the text " no signal detected" and then goes black.
    The system sounds normal and every fan starts but still the monitor seems to not be connected even when i have tested 3 differnet with different cables. Also my old GPU won´t work anymore and acts the same as the new.
    i have changed RAMs and reseted bios with the cmos battery but still no succes, so please help!
    Regards Hugo
    Specs:
    Board: MSI P67A-GD55
    Bios: unknown
    VGA:   MSI 770GTX Twin Frozr
    PSU:   Corsair VX550
    Intel Core i5-2500K Sandy Bridge 3.3GHz
    MEM: Corsair 2x2 4gb cl9 1600 mhz
    HDD: random 500gb
    COOLER: cooler master hyper 212 evo
    OS: Windows 7 64bit ultimate

    Quote from: Svet on 15-November-13, 04:21:38
    then the problem is not in the video card
    try >>Clear CMOS Guide<< with power cord removed and use your old VGA card to try to boot.
    what is your old VGA card?
    unfortunatly no succes, still the same but im gonna try annother monitor just to be sure

  • No Signal Detected?

    WOw when finally the iTune Store works on my iPhone, a new problem appears, now my iPhone is connected and says:
    *" Activation Alert"*
    "No Signal detected. Signal is required to complete activation."
    The sync is in progress but i dont know if it's really in progress. Does anyone has the same problem??

    I got that too. But it seeems to be working OK so far. It took sime time and the iphone restarted and now it is syncing. Hope this helps!

  • Ok....I have a 2012 MBP that has Yosemiti installed.  The airplay works from iTunes, but when I try to mirror from the desktop I get the "no device detected" message.  Airplay on all of my other devices work fine.  Has anyone else had this issue?

    Ok....I have a 2012 MBP that has Yosemiti installed.  The airplay works from iTunes, but when I try to mirror from the desktop I get the "no device detected" message.  Airplay on all of my other devices work fine.  Has anyone else had this issue?

    Hey Marco'96,
    Welcome to the Apple Support Communities! I understand that you are experiencing issues with AirPlay mirroring in OS X to your Apple TV. The following resource includes helpful troubleshooting steps towards the end of the article, which may resolve your issue:
    About AirPlay Mirroring in OS X - Apple Support
    http://support.apple.com/HT201343
    Thanks,
    Matt M.

  • When I update imovie to 7.1.2 it gives a "camera detected" message & quits

    Just got a new 2.8 imac 24. Imovie works fine with the built in isight. When I nstall the update it trys to detect the cam and quits.

    I've also just run the latest up-date of iMovie to 7.1.4 and the same problem happened when I try to launch iMovie. The "Camera - Detected" message appears and than iMovie quits. Has anybody found a fix to this issue?? Please help...

  • Outbound FXO calls based on Signal detection

    Hi Team,
    FXO and outbound calls while the line not connected to the FXO port, is there a way to do signal detection so the call will jump to the next fxo port

    For outbound call hunting you can use Trunk groups. You can assign multiple fxo ports to the trunk group and assign them priorty etc. From your dial-peer reference the trunk group and it will hunt the available line.
    Refer to: http://www.cisco.com/en/US/docs/ios/12_3/vvf_r/vrg_t1_ps1839_TSD_Products_Command_Reference_Chapter.html#wp1491022
    Also Refer: https://supportforums.cisco.com/discussion/12056631/need-sample-cme-multiple-fxo-ports-hunt-fashion
    -Terry
    Please rate all helpful posts and mark thread as answered if you have no other queries.

  • Virus detected Message appear on bottom of apps

    Yesterday, a virus detected message suddenly appeared on the bottom of "Guess Some" game apps and later found out it also appear on
    some other apps on the phone. Is this a false alarm as my iphone 4s has never been jail broken and all I did was update all my apps via
    apple store.

    Way to go, Deggie!

  • "IR Hardware Not Detected" message when trying to set up TV on Idea Center A700

    When I am trying to set up my computer to get TV from my set top box the computer identifies my signal and shows a small picture of the live TV.  When I click on next I get a message - IR Hardware not detected.  Can someone please tell me to what this refers?  My wireless remote works and the set top box has an IR cable that is only a few feet away.  My TV remote picks it up easily.  Is there more hardware that needs to be bought for the TV to work with this computer?
    Thanks,
    David

    Ok, I have now gotten Reader 10 installed, can open files from my desktop but IE 9 keeps crashing when I try to open PDF files even though I exited and relaunched IE 9.  I did take ownership of all the folders containing Reader 10 and then clicked OK when I got the error notice about the shortcut being installed. I did make a copy of the crash error report and it reads as follows:
    Problem signature:
    Problem Event Name: APPCRASH
    Application Name: iexplore.exe
    Application Version: 9.0.8112.16421
    Application Timestamp: 4d76255d
    Fault Module Name: IEFRAME.dll
    Fault Module Version: 9.0.8112.16440
    Fault Module Timestamp: 4eb319a7
    Exception Code: c0000005
    Exception Offset: 001b174b
    OS Version: 6.1.7601.2.1.0.768.3
    Locale ID: 1033
    Additional Information 1: 0a9e
    Additional Information 2: 0a9e372d3b4ad19135b953a78882e789
    Additional Information 3: 0a9e
    Additional Information 4: 0a9e372d3b4ad19135b953a78882e789
    Read our privacy statement online:
    Any help is greatly appreciated!

  • PDFX1a 2001  - WebNative has detected message appears?

    From within indesign CS5 I have to export HIRES pdf files using the above settings. But when I go to export the pdf I have a message appear
    'WebNative has detected that the Exported PDF not work with the PDF imaged Replacement worflow. Compatibility must be Acrobat 5 (PDF 1.4) or above and Stabdards Compliance must be none.'
    After exporting the file I'm seeing thin lines in the pdf file. I have turned off smooth art in acrobat which looks fine, but when dragged into PS the lines are there?
    Has anyone else seen this nessage before using PDFX1a 2001.
    lister

    Thanks guys,
    it seems like the Machine im working on has a plugin using WebNative tool?. Unfortunately I have no admin rights to the extensions so I cant seem to turn off this feature. Is PDF/X-1a 2001(PDF 1.3) a standard Printer option these days? I suppose most printers supply their own pdf and flatterning settings.
    I switched the PDF/X-1a 2001 to PDF1.4 instead of 1.3 and changed the Flatterner preset to 2540ppi and it bypassed this error. Also the lines dissapeared (Acrobat still highlighted the flatterning so I turned the pref off, rasterised the pdf in PS and the lines were gone.)
    it seems to only pop up when using the PDF settings.
    Thanks
    lister

  • "Signal" error messages

    Whenever I open either a new or old project, I receive the following two error messages:
    Signal
    Assertion failed:sSelf==ollsSelf==
    reinterpret_cast<MessageData*>(instuff)->Self
    and
    Signal
    Assertion failed:SAdapterSelf==o
    I have no idea what these error messages mean (nor does New Delhi, it seems). I do have problems with projects, but expect this is because I have a single HDD spinning at 5400 rpms (with and i7 chip). Of course, none of the promotional or marketing material on the software says the two or three HDDs spinning at 7200 are necessary to use the program without headaches.

    Paul,
    I am not familiar with that particular error message, but most "signal" messages are generated by the monitor itself, and indicate an issue with the, well signal. This could be because of a bad cable, a bad video card, some problem in the monitor, or some problem with the general I/O (Input Output) of the computer.
    I would look at the cable to the monitor first, at the video card next, then at the computer, and finally at the monitor itself.
    You might have luck tracking that error down on the monitor's mfgr's. Web site, or from their support department.
    If that then yields no good results, I'd address the video card next. What brand/model is it, and what is the driver version, number/date?
    Also, as another user mentioned similar issues with 16-bit displays, what Color Depth setting are you using?
    Good luck,
    Hunt

  • Signal detection on pins of parallel port

    hello,
    i am using the outport.vi in order to write to the parallel port of my windows 98 pc. I am writing a value to the port register. To detect that, i am trying to detect a signal change directly on the pin of the parallel port using an oscilloscope. I don´t detect anyhting although the vi ran without complaining. What am i doing wrong ?
    saludos
    miriam

    Hi miriam,
    I never used the access to parallel port from LV but from C based programs. As I know outport should do under Win 98.
    Are you aware that the port nubmer is in Hex? The address can change if you have one or two parallel ports in your machine.
    If you have one port it is 0x378 for LPT1.
    If you have two ports it is 0x278 for LPT1 and 0x378 for LPT2.
    Waldemar
    Waldemar
    Using 7.1.1, 8.5.1, 8.6.1, 2009 on XP and RT
    Don't forget to give Kudos to good answers and/or questions

  • Why do I get a "driver conflict detected" message after installing the latest driver.

    I have been having problems displaying print ink levels.  So, I decided to run the latest Print and Scan Doctor software.  Sure enough the diagnostic detected a driver problem and displayed a message "Driver Conflict Detected".  So, following instructions, the driver was uninstalled and new software was installed using the latest full driver and other software install.  After this was completed, the diagnostic was run again, guess what, same message.  The next timeI installed just the driver install package.  The diagnostic was again run.  Guess what, same error.  Well, after a couple of hours trying to find a different driver for a Windows 7 64 bit machine and looking for a different uninstall program, I have given up.  Oh, the other problem is repeated "offline" messages on my wife WIFI connection to the printer. Neither problem has been corrected.   Does anyone have a solution?  
    Thanks - 
    This question was solved.
    View Solution.

    Yeah as long as the functionality is there for you I wouldn't worry about the message. 
    If I helped you at all it would be great if you clicked the blue kudos star!
    If I solved your post please mark it as solved to help others.
    I'm a printer tech with HP.

  • Signal detection

    Hi! Im currently working on an ultrassonic sensor using labview. So, i have a timer that starts when i send pulses and i want it to stop, when the receiver module of the sensor detects the ultrasound and transforms it onto a signal. My problem is that i dont know how to build an vi that stops my timer when it detects the signal from the receiver. Im using a data aquisition module for my work.

    Hi Warulf,
    which DAQ module do you use? (Which DAQ hardware at all?)
    What is the expected time interval?
    In general you read in the analog signal of your transformer/receiver with a fixed sample rate. Once you read in the signal you can easily analyze it - as the samples come with a fixed rate/time interval you can use their index to calculate the time…
    Best regards,
    GerdW
    CLAD, using 2009SP1 + LV2011SP1 + LV2014SP1 on WinXP+Win7+cRIO
    Kudos are welcome

Maybe you are looking for