Access Airport extreme disk on Hard Wired Connection

Question how do you access the USB hard disk on Airport extreme via a Mac on a hard wired ethernet connection?
I have a Mac in a room outside WLAN coverage and apart from Air Port Disk utility I don't know if this is possible.
Thanks,
Garry

Garry, Welcome to the discussion area!
The same process as when you access the drive wirelessly.
If you are connected to the WAN port on the AirPort Extreme base station (AEBS), you must configure the AEBS to operate in bridge mode.

Similar Messages

Unable to access Airport Extreme Disk With Vista

I have a network with a Mac Book Pro, G5, and now a Vista PC all connected to an Airport Extreme. Connected to the AE are a printer and two harddrives. The harddrives are formatted HFS+ Journaled. All three computers have access to the Internet and to the printer. The Vista computer is unable to access the harddrives (most of the time). Prior to the Vista machine I had an XP Pro machine that was able to access the AE without any problems at all. The Vista machine will occasionally be able to access the drives but only for approximately 60 seconds. Access, when it does occur, is typically after a reboot of the AE. Following a reboot, I can map the AE drives to drive letters or simply access them from networking for from IE.
I've tried turning off the Windows firewall as well as the McAfee one and still no solution.
I've tried everything I can think of as well as scanned message boards to no avail. Any suggestions would be appreciated.

am having similar problems with USB drive connected to airport extreme. I tried with a usb key and it can only be seen by the airport base station agent and computers on the network if it is formatted using FAT32 file system. if I use any other file system to format the usb key, it cannot be seen. I have some external hard drives that windows will not allow me to to format using fat32. they are NTFS formatted and are not usable.
You might try formatting your drives in FAT32 if you can, after backing up all the files you have on the drive. then see if it works.

How do I connect airport extreme to seagate hard drive using windows

How do I connect airport extreme to seagate hard drive using windows?

First the AirPort Extreme Base Station (AEBS) cannot share out an external HDD attached to its USB port unless it is formatted in either HFS+ or FAT16/32. It will not work if the HDD is formatted in either NTFS or ExFAT.
If the HDD is formatted properly, when you access the AEBS with the AirPort Utility, does the HDD show up properly on the Disks tab of the utility?
If it does, then you would access the HDD as any other network share, using the following format: //servername/sharename. In the case of the AirPort Disk (a HDD attached to the USB port of either an Extreme or Time Capsule), the "servername" would be the Extreme's Base Station Name, and the "sharename" would be the volumename of the HDD.

Windows 7 and Airport Extreme disk do not connect

I have three windows computers (XP, VISTA & 7) and one mac mini all sharing a drive connected to my airport extreme. I can access the drive fine with computers except windows 7.
My configuration on the airport was to prompt for a disk password, so I changed it to ask for username and password and I still cannot connect.
I have tried to map it via \\10.0.1.1\Disk and also \\extreme\Disk neither work.
I have been able to connect or at least it appears to connect by showing me the drive listed in windows 7, but none of the files are present. Windows xp and vista show the files fine and still can connect.

But currently have it working with the Win 7 defaults of:
1) "Send NTLMv2 response only" for "Network security: LAN Manager authentication level"
2) "Require 128-bit encryption" for "Network security: Minimum session security for NTLM SSP based (including RPC) clients"
also, my "Windows Search" is enabled.
I might end up revisiting these ideas though, because if I disconnect the network drive from the PC and then try to remap it, I run into some of the same problems that occurred in the initial troubleshooting - in other words I cannot just map the drive, need to reboot.
So the problem that I had in summary:
- I had gotten the Airport Extreme shared USB drive to connect to the PC by first a reboot and then connecting via wireless to the Airport Extreme
- If I disconnected from the shared drive on the PC, then I could not re-map it (I could get it back by the reboot / connect mentioned above): Windows was asking for "user name" and "password" when I went through the "Map network drive", following the ideas specified in "AirPort: How to mount an AirPort Extreme USB hard disk volume in Mac OS X and Windows" (http://support.apple.com/kb/HT1331?viewlocale=en_US)
After more monkeying and searching around, I found that could fix this by:
1) On the PC, go to Start, type "advanced share" in the search box. This will take you to "Change sharing options for different network profiles" (can also get there by going to Control Panel\All Control Panel Items\Network and Sharing Center\Advanced sharing settings).
2) Once there, go down to the bottom "Password protected sharing" and click "Turn off password protected sharing". Save your changes.
3) Disconnect / reconnect to your Airport Extreme - I am doing it via the primary (non-guest) wireless.
Then, whenever I connect to the primary (non-guest) wireless on Airport Extreme, the share automatically maps itself. I can disconnect from it (the share) and it will disappear from under My Computer. To reconnect to it (the share), I just recycle the wireless connection. And, if I log on to the guest network, the share is not visible, which is how I would expect it to perform with my settings.
In Control Panel Microsoft describes "Password protected sharing" as:
When password protected sharing is on, only people who have a user account and password on this computer can access shared files, printers attached to this computer, and the Public Folders. To give other people access, you must turn off password protected sharing.
Maybe I am just tired from pounding away at this (yes, still using the "Monkey Theory" analogy - it is actually listed as the "Infinite monkey theorem" on Wikipedia if you want to read about it) but the whole thing still doesn't make much sense to me.
As far as why changing Network security policies may work for some and not others is a bit of a mystery. I did pursue this further and ran Wireshark while I changed these settings around. There were some differences in the "Negotiate Protocol Request" and "Negotiate Protocol Response" sequence, as would be expected but the end result for me was just keeping the default Win 7 values and making the changes mentioned above to get things working.
Otherwise, in Wireshark, I could just continually see as the PC got rejected for an attempt to logon to the share with its credentials, which I could not effectively change via the "Map network drive".
I also just ended up Turning off network discovery from the control panel (same location as mentioned above). Now, if I try to browse in the "Map network drive" , I get a popup that sates:
"Network discovery is turned off. Network computers and devices are not visible. Please turn on network discovery in Network and Sharing Center."
Yet, there is my nicely mapped Airport Extreme shared drive, sitting under My Computer, fully accessible and listed as a Network Drive. So, I am not sure what is really more baffling, the semantics or the technology that is at work underneath it.
I would love to hear if anyone else can get things working by doing any of the above.
Message was edited by: aprouser

I have a 3rd party hard drive with movies on it ,it is connected to my airport extreme. The AE is connected to my tv via ethernet cable. Can I stream my movies to the Tv ?

I have a 3rd party hard drive with movies on it ,it is connected to my airport extreme. The AE is connected to my tv via ethernet cable. Can I stream my movies to the Tv ?

Not without a player..
The AE is a dumb file server.. the hard disk you plug in is an even dumber hard disk.
There are no smarts in this setup.. not even DLNA. So the TV would have to be an extremely smart one to read raw files on a network drive.. none do that I know of.
A solution is WD live TV.. it can read files from just about any file source on network and play them to the TV.
Nothing apple makes will do that.. ATV is a streamer not a media player. Everything in the Apple world is tied up with itunes. So you must have a computer running itunes to use it.
You can download a more generic player for ipad, and put that as part of the network.. but you still need ATV to display the video.

Front Row in Snow Leopard fails with Airport Extreme disk

I'm using an Airport Extreme basestation (fast ethernet) to connect a USB hard drive over ethernet to my Mac Mini (1.83 Core 2 Duo with 1 GB RAM) running Snow Leopard. If I put an alias to my movies folder (all H264) on the Airport disk in my Movies folder on the Mini's HD, Front Row can see them. However, when I attempt to play a movie from the Airport disk, Front Row hangs with a black screen for several minutes and then reports an error relating to unrecognized file format. After this error Front Row will sometimes even fail to see other files that it previously saw on the Airport disk. If I move the same movies to the Movies folder on the Mini, Front Row sees them and plays them with no trouble. I did not rename the movies when I moved them to the Mini.
All of this worked properly in Leopard.
It seems as though Snow Leopard is losing connection to the Airport disk in Front Row, although the connected disk still works properly in Finder.
Any thoughts?

I have similar problems.
I have an AirPort Extreme with two USB hard drives connected to it. One drive is for media such as our iTunes library and some movies. The other drive is used as TimeMachine backup.
After upgrading to Snow Leopard we only have sporadic access to the media drive with our two laptops (MacBook Pro and MacBook) and the TimeMachine backups have stopped working completely because TM can not connect to drive. Sometimes Finder can se the drives, but most of the time it does not. When drives are visible in Finder, most of the time we can not browse the folders on the drives at all.
AirPort Utility can detect the AirPort Extreme but when I attempt to configure the unit manually the program can not read the AirPort Extreme's configuration.
The AirPort appears to work all right when it comes to accessing the internet.
Apple needs to fix this AirPort debacle ASAP!

How do I set up an Airport Express as a hard wired wifi accesspoint?

How do I set up an Airport Express as a hard wired wifi accesspoint?

Please check out the following Apple Support article for configuring your routers for a "Roaming" network. In this case the AirPort Express would be connected back to your other wireless router by Ethernet and configured as a bridge. This would effectively make the Express perform as a Wireless Access Point.

My brand new out the box airport extreme won't let anything connect to it.

My brand new out the box 5th gen (2013) airport extreme won't let anything connect to it. I've tried several setups from sratch by the book. multiple resets and restores still nothing. It just keeps telling mt that the password is in correct even though it is 100% right.
My curren set up is as follows. Phone Line -> ADSL2+ router -> Airport extreme. There is also an old airport express running of the router, this was done because the airport extremem was failing to work.
Trying to connect:
2x iPhone 4s
2x macbook air
2x Mac Pro.

You will want the Extreme to be in bridge mode if it is currently disabled. (see image below)
This will allow the ADSL2+ router to perform two important functions for your entire network: 1) Provide both the DHCP & NAT services, and 2) Provide PPPoE support to allow access to your ADSL ISPs network.
If the Extreme is left in its default state, a router, it will conflict with the first item and you will have want is known as a "double NAT" condition. Something you will want to avoid.

Remote Access Airport Extreme 802.11n

Need Help with setting up Airport Extreme 802.11n *so I can access it from a remote location.*

Is the 802.11n AirPort Extreme Base Station (AEBSn) directly connected to the Internet modem ... that is, is the AEBSn the only router in the network configuration that you are trying to reach remotely?
If so, do you have a MobileMe account and using Back to my Mac (BTMM) or another means to access the AEBSn?

This Airport Extreme base station can't connect to iCloud

I have a Airport Extreme base station (model A1408) running firmware 7.6.4.
In troubleshooting a Back to My Mac issue, I noticed that the configuration page for the base station had a yellow dot next to my apple id in the "Back to My Mac" section of the "Base Station" tab, with words underneath that say, "This Airport Extreme base station can't connect to iCloud".
When I delete the id and re-enter it, the dot goes green and no errors are generated (the id/password tokens are accepted). Then, I push "Update", and after the base station comes back, the light is yellow again. (To be clear, the dot next to the apple id is yellow, not the base station status light, which is always green.)
I'm connected to Xfinity Cable Internet service via a Motorola SB6141.
Everything iCloud related works for my various iOS and MacOS devices except Back to My Mac.
Can anyone point me to a solution? I've already been through Apple's troubleshooting and support docs related to Back to My Mac.
Thanks in advance!

NEVER MIND!
After reverting to the old LinkSys router, I left the AEBS powered up all night. This morning, I tried once again and the AEBS mysteriously started working with my laptop after reconnecting and power-cycling the cable modem. Go figure!
Unfortunately, the iMac in another room doesn't seem to be able to join the new network, but I'll close this thread and perhaps open a new one after doing some more trouble-shooting.
Thanks for your comments and suggestions.
-- Mike

Help setting up using my airport extreme to share my internet connection

I want to use my built-in airport extreme to share my internet connection with my PS3. I have a verizon aircard and have read on the internet that this can be done (but not necessarily with airport). I turned on internet sharing with airport and my ps3 reads my connection and obtains my ip address, but then it says could not connect to internet due to DNS server error.
Could someone run me down the process step-by-step so I can see what I'm doing wrong? Thanks for your help.
P.S. I have a iMac running on leopard if that matters.

ll959reds, Welcome to the discussion area!
Unfortunately the Internet Sharing provided by OS X does not provide nearly the configuration possibilities as even a very inexpensive wireless router.
Also if the firewall is enabled on the iMac, it applies equally to all ports including the AirPort (wireless) connection to the PS3. Therefore the firewall will block many of the requests from the PS3. To solve this issues, you would either need to disable the iMac's firewall or configure the iMac's firewall to allow connections via the AirPort side.
A much simpler solution is to use a wireless router instead of your iMac to provide the connection for the PS3.

HP Pavilion Entertainment PC: WiFi works, however, hard wired connection does not work.

Internet via WiFi works, however, hard wired connection does not work.
My software indicates my hardware is working properly.
However, if I connect another computer to the cable I am using, it connects to the internet without a problem.
And, if I connect my comupter to another cable that works with another computer, my computer still does not connect to the internet.
HP Pavilion dv9700 Notebook PC
32-bit Operating System
Windows Vista Home Premium Service Pack 2

It could be that the touch pad is broken on the inside and the contact area for the one button is either broken, blocked with an object or the cable going to the mother board is not inserted correctly into the mother board connector. I think in any case the case will have to come off and someone look for physical/connection problems. It doesn't sound like a software problem but there is always a chance.
Reminder: Please select the "Accept as Solution" button on the post that best answers your question. Also, you may click on the white star in the "Kudos" button for any helpful post to give that person a quick thanks. These feedback tools help keep our community active, so you receive better answers faster.

Just purchased Airport Extreme ac and lost internet connection 3X. Reset to factory settings and worked for 2 days then lost connection and remedied by unplugging power supply. Anyone else having problems?

Just purchased Airport Extreme ac and lost internet connection 3X in less than one week. Fisrt time, reset to factory settings and fixed problem. Has occurred 2 additional times and connection re-established by unplugging AP extreme. Anyone else having these problems? Do I have a bad router? Thanks.

I definitely think this is a Mavericks issue. My iMac running Mavericks is the ONLY system in the house that drops the network randomly while all other systems never lose the network. No idea how to resolve this, but here is the workaround I'm posting:
I've had the 'network drop' issue with my Airport Extreme for the last 2 months. It reconnects when I pull the ethernet cable and plug it back in. I've tried downgrading the AE firmware, resetting to factory, etc. Nothing worked. I finally threw in the towel and created a script that monitors my network connectivity and restarts my interface if it senses it has dropped:
#!/bin/ksh
while true
do
yup=`ping -c1 -t2 www.google.com|grep from`
if [[ -n $yup ]]
     then echo "Internet is connected!"
else
        ifconfig en0 down; ifconfig en0 up
        echo "Down at `date +%m%d%Y%H%M%S`">>./dropped.out
fi
sleep 5
clear
done
I know its a workaround, but its saving me the headache of constantly pulling my cable and putting it back in!
Good luck!
-Mike Gray

When connected to NETGEAR WNR1000, I can't remotely access Airport Extreme attached hard drive.

I have a hard drive connected to my Airport Extreme at home and I am staying at a friend's place where I am connecting to the Internet via a NETGEAR WNR1000 router (which is routing a broadband-cable connection from Comcast Xfinity).
When I am connected directly to the cable modem, the Airport Extreme's drives shows up in my Finder but when I'm connected via the NETGEAR router it doesn't show up.
There must be some setting in the NETGEAR router that is blocking access but I've not got clue one what setting I need to adjust or change on the router.
Could someone please advise me?

I checked the NETGEAR router settings and it was not configured to block any services or sites. I did as you advised and set up Port Mapping/Forwarding from 548 to the IP assigned to my Mac but nothing showed up in the Finder (no Shared Devices etc).
I then connected directly to the cable modem via ethernet and Shared Devices showed up in my Finder window with my Airport Extreme. I connected to one of the drives connected to the AEBSn, then unplugged the ethernet and connected the NETGEAR back to the cable modem and thus my MacBook Pro was connected via WiFi to the NETGEAR router and to the Internet.
Shared Devices disappeared from my Finder window, BUT the HD I had connected to remained connected. It was listed under my MacBook Pro's name (3rd item after the local HD, "Network"). The icon is a blue and white drive with the WiFi logo on it.
I verified that I could access the files on this remotely connected drive and did a Get Info and in the window that popped up it said "Server: afp://MilkBar._afpovertcp._tcp.malckwan.members.mac.com/Untitled%2001".
I tried to use the Connect To (Cmd-K) to connect to another drive attached to the AEBSn (Untitled%2002) using the same formatted address but could not connect.
PS. I did verify that I was mapping Port 548 to the current IP assigned to the MacBook Pro.

Airport Extreme + shared USB hard drive // Mac + PC Access

We are getting ready to purchase an Airport Extreme for our home network. Here's what we are working with:
1) Airport Extreme
2) MacBook
3) MacMini
4) PC
5) TBD USB hard drive that will be connected to AirPort Extreme *for use as shared hard drive*
From the Apple website, regarding the Airport Extreme "Hard Drive Sharing":
+How does it work? Just connect the external hard drive to the USB port on the back of your AirPort Extreme and — voilà — all the documents, videos, photos, and other files on the drive instantly become available to anyone on the secure network, Mac and PC users alike. It’s perfect for file sharing, collaborative projects, and more.+
Can anyone recommend a specific brand and model USB hard drive that they have experience with in this scenario that was/is used as a shared drive that is accessible from both Macs and PCs?
I ask this question because I have a WD external hard drive that did not play nice - it was either PC or Mac, not both.
Thanks

I have 1-4 and a Seagate FreeAgent Desk drive (not an endorsement, just answering your question), and can access the drive from all of 2-4. How you format the drive and/or what files you store on the drive will affect your ability to access/use those files on the drive from Mac/PC. For example, I can't use my iTunes library stored on the drive from the PC, as it's formatted for Mac. Honestly, I never have accessed the drive from my PC until you asked this question, but it worked!

Access Airport extreme disk on Hard Wired Connection

Similar Messages

Maybe you are looking for