Access Point 1231

Good  evening,
I  am contacting you for consultation, at our facilities are mounted Access Point  Model 1231 and Model 1242, which are connected to omni-directional antennas,  these antennas might suffer vandalism or theft, as I learned that I have broken  this antenna, there is some kind of log or alarm to tell me to my Access point  that has no antenna, I put the case for both Access Point Access Point  centralized and autonomous.
Thank  you very much

My other one shown:
NAME: "AP1210", DESCR: "Cisco Aironet 1200 Series Access Point"
PID: AIR-AP1231G-E-K9    , VID: B0 , SN: FCZ0906Z0AK
cisco AIR-AP1231G-E-K9     (PowerPC405GP) processor (revision B0) with 15138K/1236K bytes of memory.
Processor board ID FOC09030GAC
PowerPC405GP CPU at 196Mhz, revision number 0x0145
Last reset from power-on
1 FastEthernet interface
1 802.11 Radio(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:13:1A:22:B7:9F
Part Number                          : 73-8704-08
PCA Assembly Number                  : 800-23211-09
PCA Revision Number                  : A0
PCB Serial Number                    : FOC09030GAC
Top Assembly Part Number             : 800-23304-08
Top Assembly Serial Number           : FCZ0906Z0AK
Top Revision Number                  : A0
Product/Model Number                 : AIR-AP1231G-E-K9
Configuration register is 0xF
Can Fix this, to correct use?
thanks
R. Kuhn

Similar Messages

  • Need to disable AP mode multicast in 1231 series access point

    Hi
    I have one controller 2504 and some 1200 series access points.I am using 3 SSID .I want to use two ssid in HREAP mode but HREAP mode is not showinh in access point because multicast is enabled on AP mode.Please see the below picture
    I have disabled the multicast globally from CLI.
    config network multicast global disabled
    Please help me in disabling the multicast so that i can set the access point in HREAP mode.
    Thanks ....

    Hi George
    I have found a document in which it is mentioned which platform are supported..
    These are the restrictions to remember while you use H-REAP.
    Hybrid REAP is supported only on the 1130AG, 1140, 1240, 1250, 1260,           AP801, AP 802, 1040, and AP3550 APs and on the Cisco WiSM, Cisco 5500, 4400,           2100, 2500, Flex 7500 Series Controllers, the Catalyst 3750G Integrated           Wireless LAN Controller Switch, and the Controller Network Module for           Integrated Services Routers.
    But why it is giving an remark on controller tab that multicast is not supported with HREAP on this platform ?
    Is this the limitation of cisco 2504 controller or the limitation of 1231 access point ?
    Does that mean i can use my SSID in HREAP mode if i am using 1231 series access point ?
    Thanks...

  • Need to reset 1231 Access Point from LW mode, to standard mode

    How do I do this?
    I've tried the clear lwapp commands, and nothing seems to help.
    Do I need to load a new IOS?

    Using a TFTP Server to Return to a Previous Release
    Note This section does not apply to Cisco C3201WMIC and Cisco C3201LAP.
    Follow these steps to revert from LWAPP mode to autonomous mode by loading a Cisco IOS release using a TFTP server:
    Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30.
    Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.
    Step 3 On the PC where the TFTP server is located, perform these steps:
    a. Disable any software firewall products, such as Windows firewall, ZoneAlarm firewall, McAffee firewall, or others.
    b. Ensure all Windows files are visible. From Windows Explorer, click Tools > Folder Options > View > Show hidden files and folders.
    Step 4 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200 series access point, c1130-k9w7-tar.default for an 1130 series access point, and c1240-k9w7-tar.default for a 1240 series access point.
    Step 5 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.
    Step 6 Disconnect power from the access point.
    Step 7 Press and hold MODE while you reconnect power to the access point.
    Step 8 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release.
    Step 9 Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.
    Step 10 After the access point reboots, reconfigure it using the GUI or the CLI.

  • WRT54G as access point

    Hey there first post I have a wrt54g wireless router all firmware is up to date I also have the befsr41 just a regular wired router I've had it set up where the wired router is getting the dhcp and connecting to my wired computer and xbox I have a ethernet cable going from the wired router to port 4 in my wireless router with the router dhcp server set to disabled. this made it work great as an access point until now. At this point I have my wired computer wired right into port 3 of the wireless router and is connecting great however the ever important wireless function of the wireless router is now not working i've updated the firmware and tried resetting to factory settings and everything but it will still only work through the wired ports. My wireless laptop says that it is connected to the wireless network but it says "local only". now i've tried (in cmd) to ping the router wirelessly and it keeps saying transmit failed, error code 1231. does anyone have any suggestions? has the wireless portion of my wireless router failed? thanks =-eric-=

    Use static/ Manaul Ip address on wireless networkconnection.....
    Use Ip address .... subnet mask & DNS numbers ....
    Reboot the computers & see if it works ....

  • Finding the manufacture date on an access point via software

    I'd like to determine the manufacture date of our access points because we plan on converting to LWAPP? Can someone tell me the what CLI command to use and which field has the answer. thanks.

    Hi Thomas,
    Not sure about finding the Manufacture date (maybe you are trying to find out about the presence of a MIC certificate) but we did go through this coversion from Autonomous to Lightweight on our infrastructure last summer.In this process we did convert about 70 1121's and 1231's to LWAPP and it worked very well. Here are some relevant docs;
    Upgrading Autonomous Cisco Aironet Access Points to Lightweight Mode
    From this excellent doc;
    http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html
    The following Cisco Aironet access points have the ability to operate as autonomous access points or lightweight access points:
    Cisco Aironet 1240 AG Series Access Points
    Cisco Aironet 1230 AG Series Access Points
    Cisco Aironet 1200 Series Access Points that contain 802.11g (AIR-MP21G-x-K9) and/or second-generation 802.11a radios (AIR-RM21A-x-K9 or AIR-RM22A-x-K9)
    Cisco Aironet 1130 AG Series Access Points
    Cisco Aironet 1100 Series Access Points that contain 802.11g radios (AIR-AP1121G-x-K9)
    Cisco Aironet 1300 Series Access Points/Bridges (AIR-BR1310G-x-K9 or AIR-BR1310G-x-K9-R).
    From this doc;
    http://www.cisco.com/en/US/products/ps6521/prod_bulletin0900aecd80321a2c.html
    Guidelines and Tools for Migrating to the Cisco Unified Wireless Network
    http://www.cisco.com/en/US/netsol/ns340/ns394/ns348/ns337/networking_solutions_white_paper0900aecd804f1a23.shtml
    Self-Signed Certificate Manual Addition to the Controller for LWAPP-Converted APs
    LWAPP secures the control communication between the AP and the WLC by means of a secure key distribution. The secure key distribution requires already provisioned X.509 digital certificates on both the LAP and the WLC. Factory-installed certificates are referenced with the term "MIC", which is an acronym for Manufacturing Installed Certificate. Aironet APs that shipped before July 18, 2005, do not have MICs. So these APs create an SSC when they are converted to operate in lightweight mode. Controllers are programmed to accept SSCs for the authentication of specific APs.
    http://www.cisco.com/en/US/products/ps6521/products_configuration_example09186a00806a426c.shtml
    LWAPP Upgrade Tool Troubleshoot Tips
    http://www.cisco.com/en/US/tech/tk722/tk809/technologies_tech_note09186a008072d9a1.shtml
    Also, 5 points for Eric! For all your great work here lately.
    Hope this helps!
    Rob

  • Access Point Predownload Process

    I want to upgrade my wireless controller (WISM) to 6.0.19x.0.
    My question is does controller software version 6.0.188.0 and1242 and 1231 AP's
    support the access point predownload process?

    Hi,
    the below link will give u more info on assigning the IP to the LWAPP AP..
    http://www.cisco.com/en/US/products/hw/wireless/ps430/products_tech_note09186a00808e2d27.shtml#backinfo
    To  enable LAG on the WLC, Open the WLC GUI and Monitor >> Controller  >> General >> LAG >> Enable >> Reboot.
    Lemme know if this answered ur question!!
    Regards
    Surendra

  • IOS Upgrade Procedure for Access Point 1200 0r 1230 series

    Greetings all - perhaps this is posted or on the site howveer I did not see it anywhere. I have several 1231 Access Points that have an IOS on it but I would like to upgrade the IOS to the newer version. Can anyone provide a link or procedure on how to perform this.. Thank you kindly in advance

    Hi Pete,
    Have you had a look at this;
    Working with Software Images
    From this doc;
    http://www.cisco.com/en/US/products/hw/wireless/ps430/products_configuration_guide_chapter09186a0080184aa2.html#1035507
    Hope this helps!
    Rob
    Please remember to rate helpful posts.......

  • Unable to stop the event logs on access point console

    Hi team,
    I have an AIR-LAP1131AG-E-K9 access point having ios c1130-k9w8-mx.124-21a.JHB1.
    When I am trying to take the console of it there are many logs generated like LWAPP ...Go join the controller, Discover controller etc. and the ap is unable to register to the controller(2112 with ios version 6.0.199.4). I'm trying to enter the command but there are many event msg generated....How do i stop this event log. I tried entering the command no debug all. but still there are many logs...
    I want to enter the the following commands
    #lwapp ap  ip address <ip addr>.
    #lwapp a pip default-gateway <gateway ip addr>
    #lwapp ap controller ip addr <controller ip>
    #wr me
    Revert me back on urgent basis
    Thanks in advance..

    Thanks Rashika,
    Now the access point got registered to the controller..This happened becuse of country Code..
    I have changed the country code to UK, Belgium it started working fine.
    Initially when it was IN the access point was not getting register..
    But now the problem which arised is that the user is unable to get authenticated to the radius server.
    Radius server is reachable and we have done every changes required for radius server authentication.
    Users are getting rejected.
    Customer is saying that the radius server is in IN domain and the WLC/access point is in UK,BE and hence the users are unable to connect..
    Is it so??
    Rply
    Thanks in advance...

  • How do I make my AirPort Extreme a access point?

    I just bought a Time Capsule and now I want to extend my range of my network.  How do I make my AE an access point?

    In this case, you will want to configure both base stations in an extended network.
    Dynamic WDS - Extending a Wireless Network Setup
    If practical, place the base stations in near proximity to each other during the setup phase. Once done, move them to their desired locations.
    Open AirPort Utility, and then, select the base station that will connect to the Internet.
    Choose Manual Setup from the Base Station menu, or double-click the base station to open the configuration in a separate window. Enter the base station password if necessary.
    Click AirPort in the toolbar, and then, click Wireless.
    Choose “Create a wireless network” from the Wireless Mode pop-up menu, and then, select the “Allow this network to be extended” checkbox.
    Next, select the base station that will extend this network, and then, choose Manual Setup from the Base Station menu, or double-click the base station to open its configuration in a separate window. Enter the base station password if necessary.
    Choose “Extend a wireless network” from the Wireless Mode pop-up menu, and then, choose the network you want to extend from the Network Name pop-up menu.
    Enter the base station network and base station password if necessary.
    Click Update to update the base station with new network settings.
    (ref: Pages 43-44 of Apple AirPort Networks.)

  • How do I configure my AirPort Extreme as a wireless access point?  My cable modem goes to a router, and one of those ports goes to my AirPortExtreme.

    I am about to hook up my airport extreme.  My cable modem goes into a router, and one of those ports will supply my airport extreme.  I was told by the Apple Store that I would need to configure my airport extreme as a wirreless access point.  How do I do this?

    With sbcgobal I got a Gateway 2wire modem. What I would like to know is how do I set up my APE as remote?
    Unfortunately, you won't be able to do this as few non-AirPort routers will work with AirPorts in a Wireless Distribution System (WDS).

  • Can't HP Officejet pro 8100 do wifi access point?

    Yesterday my HP Officejet pro 8100 arrived and I try to connect via wifi. I thinked that It need a infrastructure access point to print via wifi.
    When I powered on the printer I osserved that It create an access point autonomously with SSID: HP-Setup-7A-Officejet Pro, with IPv4 address server, etc...
    I was very happy and I printed a page with my smartphone samsung s4 connected directly with printer access point (not wifi direct but standard wifi).
    Today no changed occurred but I can't use printer with its own access point, but only with an external wifi access point.
    Someone can help me, please? It could be an hardware problem?
    Thanks,
    Luca
    P.S. in web server I checked that "access point connectivity" (Punto di accesso wireless connettività in Italian) is checked.
    This question was solved.
    View Solution.

    Hello lucait
    To print via WiFi you need to have a wireless router setup. Once you have the wireless router setup correctly you will have a SSID and Wepkey that will enable you to add devices to your network. The network will allow all your devices to communicate not just with each other but with the internet. At the moment your printer was not put in a network so instead of broadcasting on a network it is broadcasting on it's own network called HP-Setup-7A-Officejet Pro which is only good for a short period of time to allow you to setup your wireless. I am going to assume you have a wireless network and you are just needing assistance getting the printer setup on that network.
    To set your printer up on a network you will need to reset your network defaults so your printer begins to broadcast that HP-Setup-7A-Officejet Pro network again. You can do this buy following the steps on the HP Support document Resetting the Network Settings. Once you have done this you can begin to install the software that came with your printer on your computer. You want to set the printer up wirelessly when the option arrives. The software should configure your printers wireless for you and put it on the network. Once completed you should be able to access your printer from all your devices as long as they are on the network. 
    I hope this helps resolve your wireless issue. Thank you for posting on the HP Forums. Have a great day! 
    Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
    Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
    Dunidar
    I work on behalf of HP
    Find out a bit more about me by checking out my profile!
    "Customers don’t expect you to be perfect. They do expect you to fix things when they go wrong." ~ Donald Porter

  • Setting up a netgear n300 as wireless bridge/access point with airport extremee

    I just replaced my netgear wireless router with the airport to allow our many devices on the network without knocking each other off and also increase the speed.  But would like to use the netgear as a wireless bridge or access point so that I can still connect my NTFS formatted hard drive to be shared on the network.  Any suggestions would be appreciated.  I can not seem to find my netgear router with 192.168.1.1 as that comes up with another device.  I have tried doing this with a windows laptop in another room but can not seem to make it work.  I am now hooked up directly to the airport thinking i need to do it that way and still no luck. Please help.

    As long as you intend to do this over ethernet it will work.. you cannot easily wireless repeat or bridge to an apple router.. you would need specific hardware to do it.
    What is the exact model of netgear you have?
    The setup method depends on the functionality of the router.. but lets assume it does not have a bridge or WAP mode.
    You use WAN bypass.
    1. Setup the Netgear with IP address in the correct IP range for the rest of the network.. it is hard to talk generalities so lets say the apple is main router and your network is now 10.0.1.x .. then set the Netgear to 10.0.1.250 (apple uses IP 2-200 by default) you can use any value you like outside the DHCP range. Up to the limit which is 254 as long as you keep track of all static IP devices. Apply this setting and power cycle the router.. and you might need to power cycle the computer as well to pick up the new IP.
    2. Turn off the DHCP server in the Netgear. You may lose connection to the netgear now.. do not worry about it.. (this can be combined with one.. if you firstly turn off dhcp before you change the IP.. but whatever is possible.. at some point you will need to change around and if you forget what IP .. you will be in a mess.. so write it on a label and stick on the base of the router.. also without dhcp you will either need to reset router to factory using reset button or use static ip on the computer. )
    3. Plug ethernet from LAN of the main router to LAN of the Netgear. Reboot the whole network is often necessary.
    4. In your computer plugged somewhere in the network.. open browser and go to the address you set.. 10.0.1.250 in my example.
    5. You can then setup the Netgear to do whatever you like.. DIsk access is fine.. wireless is fine.. it just cannot be a router.
    Many many reboots if you get lost. Hit reset and start over.

  • New wireless network with several access points

    Hi,
    We are planing to deploy a wireless network that will cover two floors consisting of about 5 or 6 Access points. It should have 2 or 3 SSID (placing the clients in 2 or 3 different VLANS).
    What would be the best solution for this?
    I read a lot about wireless controllers. What about an option to just buy standalone access points? Are they all configured to work with the same SSID's and on the same channel?

    A centralized controller should make your life easier:
    - Centralized config - set up everything on the controller and it gets applied to the AP's.
    - Centralized monitoring - when someone has a problem, you can check the controller instead of having to figure out the AP to which they are connecting (computers don't always connect to the closest AP)
    - Dumb AP's - if someone steals one of your APs, they will not be able to learn much about your network from a lightweight AP
    - Radio Resource Management - let the controller make the channel and power setting decisions for you
    - If you use PoE, you may never have to get on a ladder and use the console port of a lightweight AP. The AP is managed by the controller, and for the rare occasion that you can't get an AP to respond - just cycle the power to the AP via the switch port.
    There are some downsides:
    - Cost of the controller (since you're buying AP's one way or the other)
    - Most cost: If your wireless network is important, then you typically want a second wireless controller as a backup
    - Probably more downsides, but my brain hurts today

  • When using EA6400 as an access point only, certain features lost

    I've set up my EA6400 and have it connected to my Verizon MW424WR(Gigabit) and it works fine as an access point and the Twonky Server uses the USB drive I have attached to the router's USB port. Problems:
    1)I can not use the linksyssmartwifi link for management, I have to use the IP(set for 192.168.1.50) for this. When trying to register/login, the Linksys end is trying to find a Linksys router but can not and will not allow any action.
    2)Although Twonky will use the attached HD, I can not share the device over the home (Windows) network. I've tried various incantations of the IP \\192.168.1.50\(whatever share name I can think of) with no avail.
    3)Using the Linksys admin, the Device List is incomplete. Devices connected wirelessly  such as my iPod, Roku, Sony Media Player and WD HD TV Live do not show as wirelessly connected and do not have an IP listed.
    4)Is there any point in using the Media Prioritization settings since no routing is done by an access point. Or will it actually prioritize the wireless connection.
    BTW, the Verizon router can not be set in bridge mode so I have to use the router as an access point to accomplish what I wish.
    TIA,
    Randy

    Some applications and router features require the use of the WAN port. If the router is set up for LAN to LAN AP mode only, then those features won't work in this mode. Only Router mode. 
    If the ISP modem has a built in router, it's best to bridge the modem. Having 2 routers on the same line can cause connection problems: Link>http://www.practicallynetworked.com/networking/fixing_double_nat.htm and http://computer.howstuffworks.com/nat.htm If the modem can't be bridged then see if the modem has a DMZ option and input the IP address the router gets from the modem and put that into the modems DMZ. Then connect the router in router mode using the WAN port to the ISP modem, then features and apps should work.
    tduong44 wrote:
    I am having the same problem, not being able to use ANY apps like USB drive, FTP, etc when setting the device in bridge mode because I want to access the drive outside of my network using port forwarding.  Contact Linksys/Cisco support and was told that I needed to setup the Verizon router in Bridge mode..   That was it, that was the solution... AND also to check with provider for instruction how to.. WTH kind of support is that>??

  • An Error Occurred while trying to join "my wireless access point"

    Hi,
    I've been using wireless access for a year and never had a problem connecting.
    But starting yesterday I get a +*An Error Occurred while trying to join "my wireless access point", Please try again.+* Message.
    I have 2 Mac's and have no problem connecting with the other one. It’s just the IMac.
    I tried everything including resetting router, changing password, adding a $ to the password, accessing without password, deleting the whole air port and create a new one, but still getting the same message.
    I might need to add, while I was working with the IMac I didn’t use wireless for a few hours, but when I got back to my browser I noticed that I was connected to a different wireless service. (FONFREEINTERNET if it matters) I have no idea why, since I didn’t change it.
    Anyways, I tried to switch back to my access point, but it wouldn’t let me. It’ll just give me the +*An Error Occurred while trying to join "my wireless access point", Please try again.+* Message.
    Funny is when I use the FONFREEINTERNET access point the internet seems to work fine.
    I could look up Google without a problem, but when I tried to connect to Facebook for example it won’t let me. Instead a FONFREEINTERNET page will pop up with some options on how to pay! (by minute/or day/or week…)
    I get the strange feeling that they planted some kind of bug/virus!!!
    I don’t know what else to do.
    Anyone knows that problem? What can I do?
    Any help is greatly appreciated!
    I researched on FONFREEINTERNET, there’s a spot close to my house/guess that’s the one I used…
    http://maps.fon.com/ ZIP CODE 904-0113 and you’ll see a coffee pod, which is about 2 minutes walk from my house.

    Hello Tesserax,
    I get the same error message again...
    I tried the 3 suggested steps again, but unfortunately it did not work.
    After a Restart, Sleep or just the awaking from Screensaver mode I’m disconnected from my wireless Network anymore.
    Even if the Computer was asleep for just a second!
    I am able to fix the problem temporarily with Network Preferences → Assist me → Diagnostics
    Choose Airport → Choose network → Enter Password (Even if I check safe password it’ll ask me every time) → and than usually all lights on the left menu switch from red to green and I get the popup message “A Network Change has been detected. Your Internet seems to work fine.” (similar - I’m at work and don’t remember exactly)
    And it works fine…until the screensaver comes on or it sleeps again
    I have the Problem with my IMac and Mini but the IMac at least remembers my password…
    Any Ideas
    I’m connected through a Buffalo WZR2-G300N wireless router

Maybe you are looking for