Access point associated and deassociated from WLC
HI,
i have 3 AP AIR-LAP1042N-E-K9 in the same place (Event at down town) but they Sometimes the APs even disassociate from the controller temporarily, and i see the below errors on Prime infrastructure 2.0
Load threshold violation reported by 802.11b/g/n interface of AP <apname>, connected to controller <controllerIP>
Interference threshold violation reported by '802.11b/g/n' interface of AP
Coveraged threshold violation reported by 802.11b/g/n interface of AP <apname>, connected to controller <controllerIP>
what these problems and how to solve it
Thanks,
Ahmed
After these error done i see that error 802.11b/g/n interface of AP is down :controller.
please as example up time is 4:00 hours and join time changed every time may be once 12 m:15 sec, may be in another time 1h:15 m:20s
please feed me back these problem related to number of connected client because i monitor when the client exceed on AP more than 25 the AP deassociated from WLC. kindly find loggs from AP. wait your feed back.
*Mar 1 00:00:11.913: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:11.916: *** CRASH_LOG = YES
Security Core found.
Base Ethernet MAC address: 6C:20:56:48:E7:59
*Mar 1 00:00:13.876: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar 1 00:00:14.758: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1
*Mar 1 00:00:14.761: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:15.891: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:18.795: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1040 Software (C1140-K9W8-M), Version 15.2(2)JB, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 11-Dec-12 04:03 by prod_rel_team
*Mar 1 00:00:18.796: %SNMP-5-COLDSTART: SNMP agent on host 90013-03 is undergoing a cold start
*Mar 1 00:00:18.868: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:00:18.868: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 00:00:19.865: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:00:20.214: %SSH-5-ENABLED: SSH 2.0 has been enabledlwapp_crypto_init: MIC Present and Parsed Successfully
*Mar 1 00:00:46.958: Logging LWAPP message to 255.255.255.255.
*Mar 1 00:00:50.510: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
*Mar 1 00:00:51.533: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:00:52.335: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.35.49.35, mask 255.255.255.248, hostname 90013-03
*Mar 1 00:00:52.533: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:00:52.559: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:00:53.559: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Mar 1 00:01:03.221: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
*Mar 1 00:01:13.236: %CAPWAP-3-ERRORLOG: Selected MWAR 'RMS-WLC1'(index 0).
*Mar 1 00:01:13.236: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Dec 9 09:54:50.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.94.70.2 peer_port: 5246
*Dec 9 09:54:50.919: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.94.70.2 peer_port: 5246
*Dec 9 09:54:50.920: %CAPWAP-5-SENDJOIN: sending Join Request to 10.94.70.2
*Dec 9 09:54:50.929: %CAPWAP-3-ERRORLOG: Invalid event 10 & state 5 combination.
*Dec 9 09:54:50.929: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 10 state 5.
*Dec 9 09:54:50.929: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Dec 9 09:54:50.930: %CAPWAP-3-ERRORLOG: Failed to process encrypted capwap packet from 10.94.70.2
*Dec 9 09:54:51.300: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
*Dec 9 09:54:51.355: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Dec 9 09:54:51.413: %CAPWAP-5-JOINEDCONTROLLER: AP has joined controller RMS-WLC1
*Dec 9 09:54:51.464: ac_first_hop_mac - IP:10.35.49.33 Hop IP:10.35.49.33 IDB:BVI1
*Dec 9 09:54:51.464: Setting AC first hop MAC: e804.62dc.9922
*Dec 9 09:54:51.464: ac_first_hop_mac - IP:10.35.49.33 Hop IP:10.35.49.33 IDB:BVI1
*Dec 9 09:54:51.464: Setting AC first hop MAC: e804.62dc.9922
*Dec 9 09:54:51.465: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Dec 9 09:54:51.595: %WIDS-6-ENABLED: IDS Signature is loaded and enabled
*Dec 9 09:54:52.300: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Dec 9 09:54:52.383: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
*Dec 9 09:54:52.388: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Dec 9 09:54:52.464: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Dec 9 09:54:53.377: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Dec 9 09:54:53.409: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Dec 9 09:54:53.416: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
*Dec 9 09:54:53.421: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Dec 9 09:54:54.409: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Dec 9 09:54:54.416: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Dec 9 09:54:54.442: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Dec 9 09:54:55.443: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Dec 9 10:26:53.849: %WIDS-4-SIG_ALARM: Attack is detected on Sig:Standard Id:5 Channel:11 Source MAC:905f.2e62.e7a9
*Dec 9 10:32:20.938: %CAPWAP-3-ERRORLOG: Retransmission count for packet exceeded max(CAPWAP_WTP_EVENT_REQUEST
., 2)
*Dec 9 10:32:20.938: %CAPWAP-3-ERRORLOG: GOING BACK TO DISCOVER MODE
*Dec 9 10:32:20.938: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10.94.70.2:5246
*Dec 9 10:32:20.994: %WIDS-6-DISABLED: IDS Signature is removed and disabled.
*Dec 9 10:32:20.997: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
*Dec 9 10:32:21.038: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Dec 9 10:32:21.039: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
*Dec 9 10:32:21.041: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Dec 9 10:32:21.113: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Dec 9 10:32:19.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.94.69.2 peer_port: 5246
*Dec 9 10:32:19.925: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Dec 9 10:32:19.927: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.94.69.2 peer_port: 5246
*Dec 9 10:32:19.928: %CAPWAP-5-SENDJOIN: sending Join Request to 10.94.69.2
*Dec 9 10:32:19.939: %CAPWAP-3-ERRORLOG: Invalid event 10 & state 5 combination.
*Dec 9 10:32:19.939: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 10 state 5.
*Dec 9 10:32:19.939: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Dec 9 10:32:19.939: %CAPWAP-3-ERRORLOG: Failed to process encrypted capwap packet from 10.94.69.2
*Dec 9 10:32:20.093: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
*Dec 9 10:32:20.098: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Dec 9 10:32:20.370: %CAPWAP-5-JOINEDCONTROLLER: AP has joined controller UTO-WLC1
*Dec 9 10:32:20.424: ac_first_hop_mac - IP:10.35.49.33 Hop IP:10.35.49.33 IDB:BVI1
*Dec 9 10:32:20.424: Setting AC first hop MAC: e804.62dc.9922
Similar Messages
-
Access Points keep associating and disassociating from WLC
I have numerous access points, both 3502 and 3602's that are connected to Cisco 2960s POE switches that will disassociate and then reassociate themselves with the WLC. The WLC and access points are running 7.4.110.0. The particaular Cisco 2960s POE switch in this case is running 12.2(55)SE3, RELEASE SOFTWARE (fc1). This is becoming a widespread issue.
When the AP recovers, what is the physical up time and WLC association time.
Now if your AP(s) regularly reboots then I'd consider you test the cable runs using the on-board TDR feature of your switch. -
How can I get alerts if a Wireless Access Point has been disconneted from the network?
How can I get alerts if a Wireless Access Point has been disconneted from the network?
Is it possible to get alerts via email from the WLC or WCS if Access-Point has been removed from the network?
Thanks in advance.Hi,
The below link will answer ur question!!
http://www.cisco.com/en/US/docs/wireless/wcs/7.0/configuration/guide/7_0event.html#wp1229996
Please dont forget to rate the usefull posts!!
Regards
Surendra -
when I connect my apple tv to my access point upstair and connect my ipad to the same access point i cant see my apple tv when i open up the airplay menu on my ipad. but i can see the apple tv in the living room downstair which connect to the main router.
Below is some info i get about ports.
I tried to set DMZ on my main router to have full access to ported to access point upstair which is in the ip of 192.168.1.2 and the main router in the living room is the gateway router with the 192.168.1.1 ip.
I still cant see apple tv after i try the DMZ method.
any suggestion ?
These network ports are used by Apple TV for communications on your network.
TCP port 123 is used to communicate with a network time server.
TCP port 3689 is used to communicate with iTunes while using the iTunes Library Sharing feature.
UDP port 5353 is used by Apple TV for automatically finding computers with iTunes on your network using Bonjour.
TCP port 80 is used for communicating with podcast servers.
TCP port 80 and 443 are used for basic and secure communications with the iTunes Store via the Internet.
TCP port 53 is used for regular DNS.
These are well-known ports used by Apple products, like iTunes. If you can use all the features of iTunes, these ports are likely already open on your firewall or NAT router. Note: These ports may also used by other services such as YouTube and Flickr.When the Apple TV is paired with a remote, it means only that remote can control it, when it's not paired any remote can control it. You will need a remote for each of your devices.
-
What is the best way to have access to OSX and OS9 from the same machine?
What is the best way to have access to OSX and OS9 from the same machine?
Do I need to partition the hard drive? Installed both Tiger and OS 9 on the G5 and it is having problems starting up properly.
G5 Mac OS X (10.4)And here is the prove for Edwin's message: Macintosh: Some Computers Only Start Up in Mac OS X
-
how do I access the photos and videos from my computer that I backed up from my phone to verizon backup assistant plus?
You can download the PC (or mac) desktop application.
http://support.verizonwireless.com/clc/devices/knowledge_base.html?id=54607
or you can sign into My Verizon ( http://www.verizonwireless.com/myverizon ) then navigate to MyVerizon/Manage & Store media. -
I'm about to transfer the contents of my existing HDD in my (dead PSU) iMac to another computer. I'm just wanting to know if and how I will be able to access my files and documents from the old hard drive once I've made the backup?
You are not going to be able to run your old system from the backup on this old computer as the hardware is incompatible.
You need to get a new computer or a refurbished one. -
Setting up wireless Cisco Access Points independently and network layout
Hello,
I am technician in a school. I have been asked to upgrade wireless system in school. Currently I am using VDSL2 30Mbps line. I am using E4200 Router, which is providing internet services. The school has 3 floors. On one floor I have this router which is further attached with 16 port gigabit unmanageable switch. The same router is providing wireless service on the same floor using Class C ip address. From the switch I have extended a cable and took it on to another (second floor), where I have got one more gigabit switch. From that switch I have connected one router using different subnet and further i have attached two access points for the entire floor, which is working ok. From the same switch I have extended one more cable up to third floor where I have connected one more access point. So, 3 access points on three floors, 2 switches and two router. This is the current network layout.
Now school have decided to go over to fiber. ISP is going to put Juniper router and going to create vlan and will configure access restrictions. School will have 100Mbps unlimited up and download speed. Its because of increase in number of students. School is still waiting for the router and configuration to be done.
I have got 4 cisco 1602i access points (AIR-SAP1602I-Z-K9). These access points are POE supported. I have got one 8 port POE switch also. When I got these 4 cisco I didnt get power adapters with them. First I want to ask, is this normal. Don't they usually come with power adapter. I know they are POE, but cisco doesn't send them with power adapters.
Second I want to ask, if these access points can work independent without WLAN controller. Or do i have to have WLAN controller.
As fiber is not up yet so, for the time being I have connected these access points with POE switch using Cat5E cable and then further connected the POE switch with normal gigabit switch, which is further conneted with router at this point.
Please tell me if I am doing it correctely. I will also be needing help with the configuration.
Can anyone tell me how to setup these access points independently for current situation to provide internet access. How to set them on different channels etc......
Also want to know if there is any software that can detect access points and can help me manage these access points.
I shall be thankful.
SarabDUPLICATE POST
Sent from Cisco Technical Support iPhone App -
Access points lost and can't recreate them after E...
I foolishly took the latest upgrade to the E90 soft/firmware via the Nokia software updater. Previously I was connecting to the internet & downloading e-mails into my mailbox via GPRS from my phone provider (Swisscom).
Following the upgrade, as well as some lesser problems (one application disappeared, calendar entries failed to restore from the backup to my PC) I found there are no access points at all. I get "No Access Points Defined - Define One Using Connection Settings" when I open the browser. In Tools/Settings/Connection/Access Points I get "No access points defined. Define now?" and a screen with some connection settings that I can't complete.
I still have the Configuration Messages sent by Swisscom when I first put the PIN in the phone (it was bought PIN-free) that saved access point settings for GPRS and MMS. If I try to re-save these settings I get "Settings already saved. Save again anyway?" and on selecting "Yes", "Unable to save all settings. 2 settings saved" - all of which suggests that there are still access points in existence but I can't overwrite them.
The settings wizard is no good as it just seems to look at e-mail settings, which I don't think have changed. I've looked on the Swisscom web site but not found anything helpful.
Solved!
Go to Solution.Update to my previous post: I just found that the solution was to restore factory settings (under Tools/Settings for the E90). This has restored all of the old access points, and I was also able to re-save those from my phone provider so I have access to the internet & e-mails.
What confounded me slightly was that (contrary to several other posts I've seen on this forum) the software upgrade changed my Lock Code (which you need to restore Factory Settings) back to the old value of 12345 - I had changed this to another code. After waiting the necessary 5 minutes I used the old code & it worked.
In general I agree - a lot of pain and aggravation for very little advantage in taking this upgrade, so I'd say DON'T. -
Difference between "access point solution" and "hot spot solution"
Hi to all, i'm Fabio.
My customer has a bookshop and wants to allow to his customers access to the internet using wifi connection.
Here in Italy there are a lot of laws and is very hard to create this type of solution without legal permission, authorization and so on.
However, i'm reading some technical website, and lot of them propose solution based on hot spot and not access point.
Now my question my doubts:
-Is there some difference (technical and "conceptual") between hot spot and access point?
-How are the law outside Italy, in order to satisfy this type of request?
You have to think that here, based on the Italy rules, my customer should become a telecommunication operator to allow him to install ten access point for public use!!!!!!!!
Thanks, Fabio Marino.Ok Surendrea, in this case i post here what you have to translate from my link
(source: http://www.cdaweb.it/Articoli_Vista/tabid/94/articleid/305/Default.aspx?dnnprintmode=true&mid=421&SkinSrc=[G]Skins%2F_default%2FNo+Skin&ContainerSrc=[G]Containers%2F_default%2FNo+Container):
"Quali soluzioni tecnologiche possono essere adottate per tutelarsi in questo senso? Una esaustiva risposta a tale domanda viene data in questo articolo di 01Net.it. Possiamo sintetizzarne i concetti. I gestori dovrebbero preferire soluzioni di tipo hotspot, invece che access point. Questi ultimi infatti hanno la funzionalità basilare di diffusione del segnale, senza però poter tracciare l'autore di eventuali attività illecite, in quanto non esiste distinzione tra gli utenti collegati e non rimane traccia del traffico prodotto. Gli hotspot, invece, permettono di far autenticare con username e password univoci ciascun utente, e quindi rintracciarlo in caso di necessità, gestire ticket di navigazione, gestire la banda in modo che un singolo utente non la monopolizzi rallentando o intasando la navigazione altrui, separare la rete personale/aziendale da quella del Wi-Fi pubblico, e mantenere traccia di tutto il traffico attraverso i file di log (i registri degli accessi). Ecco la soluzione ideale che consente all'esercente di dimostrare di non essere l'autore di attività illecite."
English version:
"What technological solutions can be adopted to protect themselves in this way? An exhaustive answer to this question is given in this article 01Net.it. We can summarize the concepts. managers should prefer solutions like hotspots, rather than access point. These in fact have the basic functionality of spreading the signal, without being able to trace the perpetrators of any illegal activities, as there is no distinction between connected users, and no trace of the traffic generated. hotspots, however, allow to authenticate with username and passwords each user, and then track it down if needed, manage navigation tickets, manage bandwidth so that a single user does not monopolize the slowing or clogging the navigation of another, separate network and personal business than that of Wi-Fi public, and keep track of all traffic through the log files (access logs). This is the perfect solution that allows operator to demonstrate that it is not the author of any illegal activity."
May be based on this information you can learn something new -
Ping without access point association
Hypothetical situation here: Is there a way to ping a computer with a known IP and subnet without being on the same LAN.
For example, Computer A is attached to an access point and is granted an IP of 192.168.5.202 with a subnet of 255.0.0.0. Computer B is not associated with the access point.
Is it possible for Computer B to set a static IP and subnet and broadcast a ping to Computer A (or something of the like), all without actually associating with the access point?If I understand what you are asking. No.
Now, if computer B is part of a subnet that is not part of the wireless access point's subnet, and there is routing between the two subnets, and they are part of the same private network (They don't have to go out on the public Internet), it may be possible -- if you have everything set correctly.
What I think you are asking is -- if computer B is not part of any network, and you set an IP and a subnet mask can you talk to computer A. Definitely not. -
Access point VLANS and IP Addresses for RADIUS servers
Hi, i would like to have my IAS radius server authenticate clients. I have done that, so my question is about routing and VLANS and incorporating into my existing network.
What VLAN does the access point communicate to the RADIUS server on? I need to tell the access point to communicate on VLAN1, any other VLAN will not goto the radius server. The access point only has one setable ip address through the http config, is this for management or communication with the radius server?
Thanks in advance,
ChrisHello,
Would you mind sharing how you configured both the AP and IAS to work together? I'm not finding anything in the Cisco documentation that shows how to do that and I need to use my IAS server to authenticate clients who connect to the inside SSID on my AP.
By the way, I have successfully configured an AP with two SSIDs - one for guests that connects those clients to the guest VLAN (a DMZ on my PIX), and one for trusted users that connects them to the VLAN for my inside, secure network). If you haven't got that working, I'd be glad to help. -
Is Access Point name and cluster name same, if we have only 1 access point ?
if we have only 1 Access Points, will the name of access point be same as the cluster name ? can i create more then 2 cluster on same role ?
sidHi sid,
You can not create a role same with your cluster name, it will cause the DNS resource confilect.
More information:
DNS Registration with the Network Name Resource
http://blogs.msdn.com/b/clustering/archive/2009/07/17/9836756.aspx
I’m glad to be of help to you!
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place. -
Access to VPN and Skype from behind work's firewall
I'm running a Powerbook G4 with OS 10.4.11. At work I have a very fast ethernet connection perfect for internet and Work (Exchange) email, however I can't seem to access my Uni email account, VPN or several other services, notably Skype or iChat (as I work away from my kids during the week this is vitally important). I can ping the server for the VPN and both sets of IT boffins assure me that all appropriate ports are open. I can access the VPN through PCs and I am at the moment broadcasting the internet through my Airport to a PC based laptop which is running Skype quite happily. I can go to a local pub/coffee shop and access all of the services through a WiFi/Airport Network, and I have access to all these services when I'm at home (again through WiFi). What am I doing wrong? Any help would be greatly appreciated
DHi,
yes, the spilt into three subnets did help. I now can see the routers also from the LAN which solves Problem A)
Regarding the access from WAN1 to WAN2 the background is a long story about different flatrates from Provider A and B. To keep it short: DSL is stable but very slow during some hours of the day and attached to WAN2, LTE (4G) is fast but not stable (at least 2-3 hickups per day). Therefore I need the RV042 to keep the LAN clients always online as I need it for my job. The telephone is another issue. The fritzboxes do allow VOIP over their own Internet connection but also using another Fritzbox is possible. I have my telephones connected to the DSL Box (WAN2 = 192.168.179 now) and I have a flatrate for calls to cell phones with my 4G provider (WAN1 = 192.168.178 now). As the 4G keeps failing from time to time it is very annoying when it happens during a telco (and we all know Murphys law). So the ideas is to have the telphones attached to the stable (WAN2) DSL Box and reroute it for calls to cell phones via WAN1 ( which is a feature of the boxes and worked perfectly). If the 4G fails the DSL Box uses its own Internet connection to make the call (but then I have to pay for it).
So I need access from WAN2 (192.168.179) to WAN1 (192.168.178). I tried a static route in the WAN2 Box but it didn't work (I've used the RV042 WAN interface IP: 192.168.179.100 as Gateway).
Kind regards
Klaus -
CS4 : Accessing points on a Curve from keyboard
No problem in earlier versions (Control-Tab, or Control Shift Tab), unable to do so in CS4 on my MacIntel running 10.5.5. Trying to get acquainted with this version installed on an external drive on which my system is cloned.
And while I'm at it, there used to be a checkbox in PS CS3 preferences to launch Bridge, is it anywhere to be found?> TAT-like tool
What is TAT? Google didn't help.
Acronym Definition
TAT Tattoo
TAT Tourism Authority of Thailand
TAT Time After Time (song)
TAT Turn Around Time
TAT Thematic Apperception Test
TAT Tapas Acupressure Technique
TAT Tyrosine Aminotransferase
TAT The Astonishing Tribe (Sweden)
TAT Tiffani-Amber Thiessen
TAT Technical Assistance Team
TAT Thrombin-Antithrombin Complex
TAT Transactivator of Transcription (HIV protein)
TAT Total Air Temperature
TAT Tired All the Time (medical shorthand)
TAT Tetanus Antitoxin
TAT Theoretical Arrival Time
TAT Three Affiliated Tribes
TAT Transient Accommodations Tax
TAT Touraine Air Transport (airline)
TAT Ti Amo Tanto (Italian: I love you a lot)
TAT Testing and Training (SW Development and QA Testing)
TAT Trans-Atlantic Telephone cable
TAT To Accompany Troops
TAT Transitional Automated Ticket (airlines)
TAT Transport Aérien Transrégional (French: Regional Air Transport)
TAT Tactical Analysis Team
TAT Tatry/Poprad, Slovakia - Tatry/Poprad (Airport Code)
TAT Trans-America Trail (off-road jeep/motorcyce trail)
TAT Termination Attempt Trigger
TAT Technical Assessment Team
TAT Truth and Transmission (Foundation)
TAT Terrorist Action Team
TAT Technology Applications Team
TAT Test Auto Test
TAT Tyumen Avia Trans
TAT Totally Antisymmetric Tensor
TAT Two-Axis Tracking
TAT Transgenic Arthropod Team
TAT Teenage Travelers (Family Motor Coach Association)
TAT Teens Against Television
TAT Totally Awesome Trip (slang)
TAT Tactical Airlift Technology
TAT Timed Automata with Tasks
TAT Test Analysis Table
TAT Time for Average Turnaround
TAT Transportation and Ammunition Tracking
TAT Thermally-Activated Time-Dependent (reliability model)
TAT Turbine Air Temperature
TAT Text Attribute Table
TAT Toshiba Authorized Technician
Maybe you are looking for
-
Hi - I'm trying to register for an iCloud account (I've just had a baby and am terrified I'm going to lose all my photos of him!) but when I try and register, it tells me it needs an email address so I go to edit my username and try and amend it so m
-
Stacked Bar chart mouseover options
I am using the stacked bar chart. When mousing over the bars, it currently displays the totals on the very top of the bar. Is there a way to make the total display inside (or at the bottom) of the bar?
-
UPK - Player gives HTTP Error 403 error
I have created a animation using UPK. A player.exe was generated. It was playing fine on my local drive but when I post it to shared interface it gives me this error - Contact localhost:3282 home HTTP Error 403 - Forbidden Internet Explorer Have anyo
-
Help me to schedule blank report
my requirement is to schedule the report. if report does not give any results(no results) need to deliver empty(blank) spreadsheet. can anybody help me to get this done?
-
HT204088 i bought in-app purchases and it charged me 3 times, but got the product once, help!
ok so i went on sims freeplay, and tried to purchase simoleons but an authorise payment thing blocked me, i filled this form out again and again but it kept saying that the payment method was wrong or something, finally figured out what was wrong (se