Access point connection to WLC

Hi all,
I wanted to know that in Cisco wireless or in general, is it possible to connect lightweigt access point with controller without any wired connection ? or a ethernet connection between an AP and WLC is mandatory ???

What can't you find?
Reference to the Wireless LAN Controller not having a Wireless NIC? The documents won't list everything the product doesn't come with, it lists what it does come with.
This guide is helpful:
http://www.cisco.com/en/US/docs/wireless/controller/7.4/configuration/guides/consolidated/b_cg74_CONSOLIDATED.pdf
It doesn't state that the Access Points can communicate with the WLC Wirelessly because they can't.

Similar Messages

Access Points not joining WLC

Hello All,
I am trying to deploy several AIR-CAP3502E-E-K9 access points from a cisco 5508 wire lan contoller running ver 7 code. However iam having difficulty regiserting the access points with the WLC. The wlc is connect to a 3650 switch, and each access point is connected to a 2960 switch.
Problem Solved. A bad update was not allowing the access points to get their correct firmware.

You need to provide what Leo stated, that would help a lot. Anyways you can't telnet or ssh into a capwap AP if it has not joined the WLC. So that being said, provide the info Leo requested and then console into the ap and provide use with output from the console. Make sure you reboot the AP and then start capturing the output for around 5 minutes.
Sent from Cisco Technical Support iPad App

Access points connect to wrong WLC

Hello everybody,
I have a problem with some access point.
We have two WLC's one AIR-CT5508-K9 and one AIR-WLC4404-100-K9.
now i have 6 access points that don't register anymore to the right controller.
in high availability i have set the right name of primary controller and also the correct ip address, but somehow they keep registering to the other controller.
Does someone know how i can fix this problem.
info:
AIR-CT5508:SEDA-PM_Line_1
WLC4404: SEDA-PM_Office_1
6 accesspoints are connected to SEDA-PM_Line_1 but they should be connected to SEDA-PM_Office_1
settings in AP are correct in my opinion

here is the information,
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.0.116.0
RTOS Version..................................... 7.0.116.0
Bootloader Version............................... 3.2.195.10
Emergency Image Version.......................... N/A
Build Type....................................... DATA + WPS
System Name...................................... SEDA-PM_Office_1
System Location.................................. Mao, Brazil
System Contact................................... Network_Admin
System ObjectID.................................. 1.3.6.1.4.1.14179.1.1.4.3
IP Address....................................... 105.103.112.5
System Up Time................................... 8 days 15 hrs 9 mins 55 secs
System Timezone Location.........................
Configured Country............................... US - United States
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +38 C
--More-- or (q)uit
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Disabled
Number of WLANs.................................. 13
Number of Active Clients......................... 132
Burned-in MAC Address............................ 00:22:55:91:2B:C0
Crypto Accelerator 1............................. Absent
Crypto Accelerator 2............................. Absent
Power Supply 1................................... Absent
Power Supply 2................................... Present, OK
Maximum number of APs supported.................. 100
(Cisco Controller) >show time
Time............................................. Thu Jan 9 07:58:29 2014
Timezone delta................................... -4:0
Timezone location................................
NTP Servers
    NTP Polling Interval.........................     86400
     Index     NTP Key Index     NTP Server      NTP Msg Auth Status
       1              0        211.189.10.2       AUTH DISABLED
AP information
Warehouse_AP-3#sh version
Cisco IOS Software, C1240 Software (C1240-K9W8-M), Version 12.4(23c)JA2, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Wed 13-Apr-11 12:58 by prod_rel_team
ROM: Bootstrap program is C1240 boot loader
BOOTLDR: C1240 Boot Loader (C1240-BOOT-M) Version 12.4(13d)JA, RELEASE SOFTWARE (fc2)
Warehouse_AP-3 uptime is 18 hours, 16 minutes
System returned to ROM by power-on
System image file is "flash:/c1240-k9w8-mx.124-23c.JA2/c1240-k9w8-mx.124-23c.JA2"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-LAP1242AG-A-K9   (PowerPCElvis) processor (revision A0) with 27638K/5120K bytes of memory.
Processor board ID FTX1233B943
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from power-on
LWAPP image version 7.0.116.0
1 FastEthernet interface
2 802.11 Radio(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:1D:70:96:64:A0
Part Number                          : 73-9925-07
PCA Assembly Number                  : 800-26579-06
PCA Revision Number                  : A0
PCB Serial Number                    : FOC12320AKT
Top Assembly Part Number             : 800-29151-03
Top Assembly Serial Number           : FTX1233B943
Top Revision Number                  : A0
Product/Model Number                 : AIR-LAP1242AG-A-K9
Configuration register is 0xF
Warehouse_AP-3#sh ip interface brief
Interface                  IP-Address      OK? Method Status                Protocol
Dot11Radio0                unassigned      NO unset up                    up
Dot11Radio1                unassigned      NO unset administratively down down
FastEthernet0              105.103.27.19   YES other up                    up
Warehouse_AP-3#sh inventory
NAME: "AP1240", DESCR: "Cisco Aironet 1240 Series (IEEE 802.11a/g) Access Point"
PID: AIR-LAP1242AG-A-K9, VID: V03, SN: FTX1233B943
there are 7 AP's that not register to the right controller some are different models:
Warehouse_AP-1 - AIR-LAP1242G-A-K9
Warehouse_AP-3 - AIR-LAP1242AG-A-K9
Warehouse_AP-5 - AIR-LAP1242G-A-K9
Warehouse_AP-6 - AIR-LAP1242G-A-K9
Warehouse_AP-7 - AIR-CAP3502I-T-K9
Warehouse_AP-9 - AIR-LAP1242AG-A-K9
Warehouse_AP-10 - AIR-LAP1242G-A-K9
Thank you for your help!!

Access points joining different WLC

hi
i have a wireless controller module( NME-AIR-WLC25-K9) installed in a Cisco 2851 ISR, this setup is in my remote site, we are connected through MAN network. In our main office i have a cisco 4402 wireless controller. so whenever i install a AP in my remote site instead of joiining the remote site WLC, the access point joins my main office 4402 controller, i dont why it is happening, the AP is not even trying to join the remote site WLC.. i have not configured high availability and both these controller are in separate RF network.
the firmware version in NME-AIR-WLC25-K9 is 7.0.98.0 ...
the version in the other controller is 6.0.196.0
Please let me know what is else i need to check asap
Thanks
karthik

Hi,
Did you even see the AP trying to join the local controller? If the controller are in different domains, the AP will prefer the remote controller since it join that one first. Since you are running 5.2, try configure on the AP the primary controller with the name, and local IP address of the local controller, and then reboot the AP. See if after that the AP join. run debug capwap events enable to see if you see the AP event trying to join the controller.
Regards,
Manuel

Access Points Joining Random WLC

My environment contains 4 seperate controllers. 1 controller in the datacenter which remote offices use with HREAP and discover this WLC using DNS We will call this Controller WLC1. 2 more controllers (WLC 2 and WLC 3) in the corporate headquarters to support >40 access points in a N+1 configuration and finally an anchor controller which doesnt matter in this post.
What I am experiencing is Access points in the Corporate office are using DHCP option 43 to discover the WLC2. every night or after long periods of time a random number of my access points are either rebooting or most likely sleeping. Then are attaching them selves to WLC 1 which is in the datacenter and is not supporting DHCP from that location which to clients make the wireless network seem to be down.
I think that with using a hybrid of DHCP and DNS is partly my issue but it shouldnt be. I have primed all the Access point to look at primary controller WLC1 and secondary controller WLC2 both by name and using the IP address of the respective management ports.
Can there be any explaination for this and why this seems to be so random?
WLCs are 5508
Corporate Access points are 1142
***EDIT
After some more investigation this isnt completely random rebooting the access points in question are connected to a new 4506-E chassis with the Sup 6-E while the other access points are connected to a 6509-E.. not sure how much this matters but I am seeing in the access point logs that about every 2-3 hours they are accessing DHCP again and sometime not successfully. Is there some EnergyWise or power savings happening on the 4500 possibly??

I understand that all and here is a screen shot (see attached) of an ap that was on WLC 2 last night at midnight when i wrote this orginally and now how jumped to WLC 2.. The major issue here is that WLC 1 does not give out DHCP because it is used for HREAP and remote office that have other local DHCP servers.
I am running code 6.0.199.4
Now yes all controllers WLC1,2,and3 are in the same mobilty group. Maybe I should move the WLC1 out of the mobility group and that might solve the issue. Here is a log too. See timing is 3 hours and then its trying to find another controller. I see a retransmission count exceeded here. What can cause that? I have 4 port LAG configured on both WLC2 and WLC3 and they are both on seperate 6500 switches. This access point is on a seperate floor connected to a 4500 with uplink to each of the 6500's
**********LOG from Access Point***********
*Oct 14 02:41:21.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.104.210.21 peer_port: 5246 This Is correct
*Oct 14 02:41:21.000: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Oct 14 02:41:21.826: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.104.210.21 peer_port: 5246
*Oct 14 02:41:21.827: %CAPWAP-5-SENDJOIN: sending Join Request to 10.104.210.21
*Oct 14 02:41:21.827: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Oct 14 02:41:21.911: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*Oct 14 02:41:22.047: %CAPWAP-5-CHANGED: CAPWAP changed state to UP
*Oct 14 02:41:22.052: %LWAPP-3-CLIENTEVENTLOG: Received AP Syslog IP Address(255.255.255.255) configuration.
*Oct 14 02:41:22.173: %CAPWAP-5-JOINEDCONTROLLER: AP has joined controller nwcp01-1211-02b
*Oct 14 02:41:22.254: %LWAPP-3-CLIENTEVENTLOG: SSID Roswifi added to the slot[0]
*Oct 14 02:41:22.255: %DOT11-4-NO_HT: Interface Dot11Radio0, Mcs rates disabled on vlan 1 due to WMM is not enabled
*Oct 14 02:41:22.257: %LWAPP-3-CLIENTEVENTLOG: SSID RosGuest added to the slot[0]
*Oct 14 02:41:22.259: %LWAPP-3-CLIENTEVENTLOG: SSID Roswifi added to the slot[1]
*Oct 14 02:41:22.261: %LWAPP-3-CLIENTEVENTLOG: SSID RosGuest added to the slot[1]
*Oct 14 02:41:22.263: %DOT11-4-NO_HT: Interface Dot11Radio1, Mcs rates disabled on vlan 1 due to WMM is not enabled
*Oct 14 02:41:22.263: %DOT11-4-NO_HT: Interface Dot11Radio1, Mcs rates disabled on vlan 2 due to WMM is not enabled
*Oct 14 02:41:22.264: %DOT11-4-NO_HT: Interface Dot11Radio0, Mcs rates disabled on vlan 2 due to WMM is not enabled
*Oct 14 02:41:22.274: %WIDS-6-ENABLED: IDS Signature is loaded and enabled
*Oct 14 05:57:40.164: %CAPWAP-3-ERRORLOG: Retransmission count for packet exceeded max(CAPWAP_ECHO_REQUEST
., 3)
*Oct 14 05:57:40.164: %CAPWAP-3-ERRORLOG: GOING BACK TO DISCOVER MODE
*Oct 14 05:57:40.164: %DTLS-5-SEND_ALERT: Send WARNING : Close notify Alert to 10.104.210.21:5246 *** This is correct
*Oct 14 05:57:40.206: %WIDS-6-DISABLED: IDS Signature is removed and disabled.
*Oct 14 05:57:40.207: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Oct 14 05:57:40.207: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Oct 14 05:57:50.229: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Oct 14 05:57:49.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.98.10.20 peer_port: 5246 **This is the controller it should never get on.
*Oct 14 05:57:49.000: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Oct 14 05:57:49.844: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.98.10.20 peer_port: 5246
*Oct 14 05:57:49.845: %CAPWAP-5-SENDJOIN: sending Join Request to 10.98.10.20
*Oct 14 05:57:49.845: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*Oct 14 05:57:49.930: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*Oct 14 05:57:50.078: %CAPWAP-5-CHANGED: CAPWAP changed state to UP
*Oct 14 05:57:50.078: %LWAPP-3-CLIENTEVENTLOG: Received AP Syslog IP Address(255.255.255.255) configuration.
*Oct 14 05:57:50.206: %CAPWAP-5-JOINEDCONTROLLER: AP has joined controller nep00WLC00e
*Oct 14 05:57:50.293: %LWAPP-3-CLIENTEVENTLOG: SSID Roswifi added to the slot[0]
*Oct 14 05:57:50.298: %LWAPP-3-CLIENTEVENTLOG: SSID RosGuest added to the slot[0]
*Oct 14 05:57:50.303: %LWAPP-3-CLIENTEVENTLOG: SSID Roswifi added to the slot[1]
*Oct 14 05:57:50.309: %LWAPP-3-CLIENTEVENTLOG: SSID RosGuest added to the slot[1]
*Oct 14 05:57:50.414: %WIDS-6-ENABLED: IDS Signature is loaded and enabled

Can I disable my Verizon Fios Router Wireless radio, connect it to a switch and use my airport express as my wireless access point connected to an in wall ethernet port?

Here's the deal. I have a Verizon Fios MI424WR router. My house has CAT5 throughout the house. The media panel is located in the garage. I want to take the Verizon Fios Router and cannot it in the media panel so I can connect a switch to it, that way, all my CAT5 can fire throughout the house. Verizon being Verizon decided to connect the router directly in the office.
Can I go this route (Router in media panel, switch cross connect to it) and use Airport Express, connected to one of the in-wall CAT5 ports in my house and then set it up as my wireless access point to provide wifi to my portable devices (iPad, iPhone, Macbook)? Is this possible? Will Airport Express comminicate with my verizon router via ethernet in-wall? Do I have to turn off the wireless radio in the Verizon router? Any help would be greatly appreciated!

That is right, by hard wired I was just making clear wired vs wireless attachment. AirPort family of devices will only act in a repeater mode with their own family members, not FiOS routers. they have to be wired to work.
There are some useful docs you can download from Apple, Support, Manuals, Peripherals, AirPort (just follow thos links from the Support button on the top bar):
Apple AirPort Networks
Designing AirPort Networks
AirPort Express Setup Guide
The last has a diagram of what you are trying to do, though without the house wiring, etc., but the basic principle.

Have apple tv 2g and several IDevices (ipad, iphone..)and around the house i have several access point connect via UTP cable to the same router/modem, but when i try Airplay it wont work if the devices are on dif wifi conn. regardelless its the same LAN.

Problem with Homesharing/Airplay with dif IDevices (Itunes with a PC, Iphone, Ipad, Itouch etc) using my home wifi connections that has several access point throu out the house and they all are connected via UTP cable to the same modem/router (My LAN).
When i try to use airplay or homesharing both devices have to in the same ACCESS POINT (it does not mather if its WIRED or WIRELESS, i have the same problem with both).
Any ideas?? This did not happen before i upgraded ITUNES in order to use IOS5.
Thanks

Thanks for the advice. But i dont have any devices sync wifi. It also happens with older versions of IOS on iphone 4.2.1 and 3.1.3 and also IOS5 (no wifi sync enable).
Basiclly when i try to airplay music using itunes (pc) to my apple tv 2g (4.3.3.) they both have to be in the same access point, if the apple tv is connect via UTP cable i have to be connected to that access point wifi. Basicly dosent work with dif access points. Also if i manage to be on the same access point (itunes using a pc and the apple tv) if i have to use Remote App to change songs i have to be in the access point to.. can not see the devices...
Any ideas?

SNMP lightweight access point connected to 4400

I am trying to monitor 1250 ap's directly via snmp. Is it possible to consolidate the SNMP MIB of the 1250 ap's who are connected to 4400 controller running R 5.2.
I am wondering if it's possible to monitor access points directly (not via wcs or controller) via snmp?
Regards, Wim

If the AP is in LWAPP mode, you cannot directly poll the AP using SNMP. You have to poll the controller to get all the information about the AP. You can download the MIBs for controller v5.2 form the URL below.
http://tools.cisco.com/support/downloads/go/InterfaceModuleSWT.x?mdfid=279911269&mdfLevel=Model&treeName=Wireless&modelName=Cisco%204404%20Wireless%20LAN%20Controller&treeMdfId=278875243
Pushkar

Router and access point connection

Tried to get smart today, took and set up my network with a wrt54gs the other day and still have some headaches after finally getting things to work. but my idea was to take my old wrt54g router and place it at the other end of my house for the wii system. I took the old router and changed the setting from gateway to router and gave it a new internal ip address. Everything worked fine, all the wired and wirless computers including the wii worked great, but when I went to my computer, where I installed the easylink program, it showed I changed networks. Do the setup crap again and it can not find the router but showed the old one as the new netork and could not connect, could not get internet or anything at this computer. But every other computer throughout the house was working great and connected to the net with no problem, the only one not connecting is the only one with easylink keeping it from connecting.
So I disconnect the added router/access point and had to run setup again with easy link, once it was up again I reconnect the old router and everything was great, showed the old as an access point and all the devices on the network. So things are great until I close my lid and my computer goes into standby, when I open it up I have the same problem again, but this time I know what to do, and I find as long as I keep this computer on all is great, shut it down all others equipment still works fine all except for the one computer with easylink on it.
Any ideas on to resolve this, I know people in the forums have said for a long time you can't use the two routers the way I have them set up, but it works great, the only problem is easylink keeps screwing me up on the one computer, if I moved the program to another computer it will do the same to that one and leave this one connecting just fine. So far my experience with easylink has been horrible, the only reason it was installed was because the box said it must be installed prior to anything else. before I just plugged things in and put in the settings I needed and life went on.

Hey,
I think you can try to update the firmware of the router, to check if that stops connection dropping. To update the firmware of router try this:
Go to www.linksys.com/download and select correct model number and version number. Download the firmware and save it on your computer.
Check the file it should be firmware image file like .bin etc. If it is a compressed zip file extract it to get firmware image file.
Open setup page of router by typing http://192.168.1.1 in browser’s address bar, and typing password as "admin" and no user name.
Go to administration tab there
Go to firmware update sub-tab there
Browse for the firmware image file and click update
When update completes turn off modem & router.
After 2 minutes turn on modem and after 2 more minutes turn on router & it will definately work!!!

Router and access point connected to FIOS router

Here's my situation. Just installed Verizon Fios which supplies their own Actiontec Wireless router. I have an existing network which comprises a WRTG54Gv6 which was connected to a DSL modem for internet access originally and a WAP54G accesss point as a Repeater to extend the network wirelessly. I have quite a few wired and wireless connection to this netwrok and wish to retain these devices. My question is, based on where I had to connect the new FIOS router(which is where the access point is) can I connect the WAP54 to the FIOS router(through a switch) and allow the combined WAP54/WRT54G network to still provide my network services and deactivate the wireless service from the FIOS router. How do I configure the FIOS router, the WRTG54 and the WAP54(if change neded).
Thanks in advanced if anyone can help.

Easiest way to configure the Verizon FIOS with Linksys is - Leave the Verizon FIOS unplugged from the Linksys Router and disconnect it's power cable.
1. Connect a computer to the Linksys Router it's Internet Port...
2. Access the web interface of the Linksys Router, change it's default address to 10.10.10.1 and leave it's DHCP Server Settings 'Enabled'. Once done you should Power cycle the Linksys Router.Don't change the Router Mode.
3.Connect Verizon FIOS from it's Ethernet Port to the Linksys Router on the Internet Port.
4. See if you can access the Internet...
You can also have a look at this link to connect two routers.However, both the router's used in the link are linksys routers but you can still follow the link.

Access Points connection drop approximately 30 times with 802.1x Radius

Hello Everyone,
As you can see from the top this is my problem that could not solve for 2 weeks. To summarize again, I used to my access points with standart configuration, I mean vlans, dhcp and other basic configration. After we increased security of our access points we started to encouter connection drops issue.
These are the example logs;
Interface Dot11Radio0, Deauthenticating Station xxxx.xxxx.xxxx (my mac address) Reason: Previous authentication no longer valid
Also a lot of:
interface Dot11Radio0, Deauthenticating Station xxxx.xxxx.xxxx (my mac address) Reason: Sending station has left the BSS
as well as we have a lot of authentication failures such like:
%DOT11-7-AUTH_FAILED: Station xxxx.xxxx.xxxx (my mac address) Authentication failed
What should I do ?
Thanks in advance

I have finally found something to look into :/
000619: Jan 18 16:50:11 A: RADIUS: AAA Unsupported Attr: ssid [263] 6
000620: Jan 18 16:50:11 A: RADIUS: 48 53 52 2D [xxx-]
000621: Jan 18 16:50:11 A: RADIUS: AAA Unsupported Attr: interface [156] 4
000622: Jan 18 16:50:11 A: RADIUS: 32 35 [25]
This is with various debugging active on the WDS. And this might be the reason why it doesn't work.

602-OEAP Access Point broken after WLC upgrade to 7.4.100.0

Hey all,
I have a TAC case open, but it doesn't seem to be making any progress....
I upgraded my 5508 controller from 7.2.111.3 up to 7.4.100.0
Most of my APs are fine. 3500s, 1100s etc.except for 602i APs. The APs associate, they update software etc, but they won't broadcast the WLAN.
An interesting thing, on the 602 AP, in the log, I see this:
*Mar 06 15:08:12.667: SSID remote, WLAN Profile Name: RemoteOEAP, added to the slot[0], disabled
So the AP is definately talking to the WLC and being pushed the correct WLAN profile.
Another thing I noticed:
On the controller, the AP shows the the Admin status of the radios is showing DOWN, but the Admin status on the AP itself shows UP
I've done a factory reset on the APs to no avail. I have a 2504 WLC as well that i'm in the process of implementing in a DMZ specificially for these APs, and for testing purposes, I associated the 602 Ap to that WLC as well. This one is running 7.4.100.0 too, same results. It would appear to be a problem with this version of software?
Anyone else had this problem?

Hey, thanks for taking a look at this. Unfortenately, that's not the issue in this case. The AP is set to "United States" and the WLC is only configured for US. Just so I'm looking in the correct place:
On the AP in the WLC, it's under the "Advanced" tab
On the WLC, its under Wireless -> Country correct?
The frustrating part is that the 600 really doesn't have anything that can be configured on it, which means troubleshooting is also limited.

MFP Anomaly Detected Access Points are moving from one wlc to another and vice versa

Hi together,
a customer has lost some Access Points to another WLC with 7.2 and then they come back after 15 minutes to the origin WLC with 7.5
Attached the messages
MFP Protection is configured as optional
152
Wed Nov 27 05:33:26 2013
MFP Anomaly Detected - 1 Not encrypted event(s) found as   violated by the radio 58:bf:ea:0f:67:4a and detected by the dot11 interface   at slot 1 of AP 58:bf:ea:0f:67:40 in 300 seconds when observing . Client's   last source mac 70:11:24:e4:43:0f
153
Wed Nov 27 05:31:40 2013
AP Disassociated. Base Radio MAC:88:43:e1:56:91:d0
154
Wed Nov 27 05:31:40 2013
AP's Interface:0(802.11b) Operation State Down: Base Radio   MAC:88:43:e1:56:91:d0 Cause=New Discovery Status:NA
155
Wed Nov 27 05:31:33 2013
AP Disassociated. Base Radio MAC:58:bf:ea:0f:73:d0
156
Wed Nov 27 05:31:33 2013
AP's Interface:1(802.11a) Operation State Down: Base Radio   MAC:58:bf:ea:0f:73:d0 Cause=New Discovery Status:NA
157
Wed Nov 27 05:31:33 2013
AP's Interface:0(802.11b) Operation State Down: Base Radio   MAC:58:bf:ea:0f:73:d0 Cause=New Discovery Status:NA
158
Wed Nov 27 05:31:28 2013
AP Disassociated. Base Radio MAC:58:bf:ea:0f:fc:20
159
Wed Nov 27 05:31:28 2013
AP's Interface:1(802.11a) Operation State Down: Base Radio   MAC:58:bf:ea:0f:fc:20 Cause=New Discovery Status:NA
160
Wed Nov 27 05:31:28 2013
AP's Interface:0(802.11b) Operation State Down: Base Radio   MAC:58:bf:ea:0f:fc:20 Cause=New Discovery Status:NA
161
Wed Nov 27 05:31:17 2013
AP Disassociated. Base Radio MAC:b4:e9:b0:e4:02:20
162
Wed Nov 27 05:31:17 2013
AP's Interface:1(802.11a) Operation State Down: Base Radio   MAC:b4:e9:b0:e4:02:20 Cause=New Discovery Status:NA
163
Wed Nov 27 05:31:17 2013
AP's Interface:0(802.11b) Operation State Down: Base Radio   MAC:b4:e9:b0:e4:02:20 Cause=New Discovery Status:NA
164
Wed Nov 27 05:31:15 2013
AP Disassociated. Base Radio MAC:a4:18:75:eb:da:b0
165
Wed Nov 27 05:31:15 2013
AP's Interface:1(802.11a) Operation State Down: Base Radio   MAC:a4:18:75:eb:da:b0 Cause=New Discovery Status:NA
166
Wed Nov 27 05:31:15 2013
AP's Interface:0(802.11b) Operation State Down: Base Radio   MAC:a4:18:75:eb:da:b0 Cause=New Discovery Status:NA
167
Wed Nov 27 05:28:26 2013
MFP Anomaly Detected - 35 Not encrypted event(s) found as   violated by the radio d8:24:bd:2f:df:6f and detected by the dot11 interface   at slot 1 of AP d8:24:bd:2f:df:60 in 300 seconds when observing Deauth.   Client's last source mac 00:23:14:a7:e3:54
168
Wed Nov 27 05:23:26 2013
MFP Anomaly Detected - 23 Not encrypted event(s) found as   violated by the radio f8:4f:57:a5:40:b2 and detected by the dot11 interface   at slot 0 of AP f8:4f:57:a5:40:b0 in 300 seconds when observing . Client's   last source mac 44:4c:0c:ba:27:77
Don´t know at the moment how to handle it.
Regards
Alex

Hi lAlex,
Disable Client MFP under WLAN advanced tab & see if this still occur
Regards
Rasika
**** Pls rate all useful responses *****

Connect Netgear access point to Home Hub?

Before I switched to using a Home Hub 2, I was using a Netgear router/modem (DG834G).
And I also had a Netgear WPN802 access point connected to the DG834G router/modem (via ethernet cable), and this enabled me to connect to internet using wifi from another location in my house. Just seemed to work.
But I can't seem to get this to work with the Home Hub. When the access point is plugged in to the Home Hub, it doesn't seem to show up in the Devices part of the Home Hub, and I can't connect to the access point via its default IP address (192.168.0.231). I can't see anything in the Home Hub to configure to make this work. On the access point, the ethernet light is lit, which suggests that it can "see" something on the other end of the cable (and the light goes out when I unplug the other end from the Home Hub).
Any hints?
Thanks.

You will need to change the default IP address of the Netgear WPN802 so that it is in the same subnet as the home hub.
The full details on how to do this are here http://kbserver.netgear.com/pdf/wpn_802_ref_manual.pdf
Look at page 23 and change the IP address in the Basic settings.
You could change it to 192.168.1.231 if you wish. It would still not show on the home hub because it is manually assigned. But it should work fine.
I have an additional Belkin wireless access point on my hub, which uses the address 192.168.1.200, and that works fine.
There are some useful help pages here, for BT Broadband customers only, on my personal website.
BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones.

Connection between lightweight access point and switch?

Hello everybody,
I am a bit confused about cisco 1000 series access point connection. On wireless lan controller and lightweight access point basic configuration example document id 69719 (http://www.cisco.com/en/US/products/ps6366/products_configuration_example09186a0080665cdf.shtml), I understood the access point has two vlans associated with (vlan 3 and 4). Am I correct?
Why is connection between access point and catalyst port just access port rather 802.1q trunk? How vlan traffic can traverse from the access point to controller?
Please advice.
Many thanks,
Nitass

Nitass,
The AP itself does not need to be a trunked port, but the uplink to the controller does. When using a Lightweight enviroment, all the traffic passes thru an encrypted LWAPP tunnel from the AP to the controller, and then gets sent out the correct VLAN interface on the controller.

Access point connection to WLC

Similar Messages

Maybe you are looking for