Access point ethernet issue

My Cisco 1252 AG's ehternet port is not working, would you please help me how to fix it. the bvi1 interface up.

It was powering up using power injector.
and here is the sh interface go
GigabitEthernet0 is up, line protocol is down
Hardware is PowerPC 8349 Ethernet, address is c84c.75d4.b39c (bia c84c.75d4.b39c)
Internet address is 10.0.0.4/24
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
     reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Full-duplex, 100Mb/s, media type is T
output flow-control is unsupported, input flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:31:41, output 00:01:28, output hang never
Last clearing of "show interface" counters never
Input queue: 0/1677/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
     6 packets input, 480 bytes, 0 no buffer
     Received 6 broadcasts, 0 runts, 0 giants, 0 throttles
     2 input errors, 2 CRC, 0 frame, 0 overrun, 0 ignored
     0 watchdog, 0 multicast, 0 pause input
     0 input packets with dribble condition detected
     249 packets output, 57652 bytes, 0 underruns
     0 output errors, 0 collisions, 4 interface resets
     0 babbles, 0 late collision, 0 deferred
     0 lost carrier, 0 no carrier, 0 pause output
     0 output buffer failures, 0 output buffers swapped out

Similar Messages

1220 Access Points Dhcp Issue

I have two 1220 ap's plugged into an unmanaged switch. I'm able to connect to the ap but I'm unable to receive dhcp info from our server. We have a 2950 switch that feeds to one of the unmanaged switch's and the other unmanaged switch is plugged into the other switch. What am I missing in the config to allow dhcp to the client? Do I need to add and ip helper on the 2950 that feeds the unmanged switches? Thanks to all
2950--Switch--Switch
1220 1220
(I'm using Vxworks)

I too am having trouble with my 1240 AG and DHCP. I would try this:
Connect to the router using the web GUI.
Go into System Software and System Configuration.
Click on show tech support.
Click on Configure
Click on IP
Click on DHCP Server
Enter in the DHCP server name or IP address and click on Address.
This should spawn DHCP to the client.
Once this is completed you can go back and view the config file and see the DHCP server listed. I hope this helps!

Downgraded A1240 Access point to IOS that support CLI command

I have a new A1240 and it IOS is working with new command LWAPP and need a control server to manage the access point. It (ios) does not have configure terminal command. I think I can delete the IOS in the flash and load a older version IOS. I went ahead and deleted the IOS and assumed the access point will go to rommon mode and allows me to archive a tar file (older ios) into the access point. However, I only get AP: prompt and stuck here. I can not run copy or archive command. What are recover process. Need your expert guidance. Au Ray Singapore

Hi Au Ray,
Have you tried this method?
Using the MODE button
You can use the MODE button on 1100 and 1200 series access points to reload the access point image file from an active Trivial File Transfer Protocol (TFTP) server on your network or on a PC connected to the access point Ethernet port.
This process resets all configuration settings to factory defaults, including passwords, WEP keys, the access point IP address, and SSIDs.
Follow these steps to reload the access point image file:
Step 1 The PC you intend to use must be configured with a static IP address in the range of 10.0.0.2 to 10.0.0.30.
Step 2 Make sure that the PC contains the access point image file (such as c1100-k9w7-tar.122-13.JA.tar for an 1100 series access point or c1200-k9w7-tar.122-13.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated. For additional information, refer to the "Obtaining the Access Point Image File" and "Obtaining TFTP Server Software" sections.
Step 3 Rename the access point image file in the TFTP server folder to c1100-k9w7-tar.default for an 1100 series access point or c1200-k9w7-tar.default for a 1200 series access point.
Step 4 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.
Step 5 Disconnect power (the power jack for external power or the Ethernet cable for in-line power) from the access point.
Step 6 Press and hold the MODE button while you reconnect power to the access point.
Step 7 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds), and release the MODE button.
Step 8 Wait until the access point reboots as indicated by all LEDs turning green followed by the Status LED blinking green.
Step 9 After the access point reboots, you must reconfigure the access point by using the Web-browser interface or the CLI.
From this doc;
http://www.cisco.com/en/US/products/hw/wireless/ps4570/products_configuration_guide_chapter09186a00801d0188.html#wp1040300
Hope this helps!
Rob

Outdoor Access points PoE power issues

We are currently deploying 5 more 1530 Outdoor Access points to the existing 2504 wireless controller with 15 Airlap 1142n AP's.Now all the AP's are connected to the catalyst cisco 2960 switch.
a)Is the catalyst 2960 switch supply enough power for the outdoor AP's or I have to use any external power injector source?

Is the 2960 370W or 720W?
"The Cisco Aironet 1530 Series can be powered over the Ethernet connection with power directly from an appropriately powered switch port or from an inline power injector."
The 1530s take:
1530I: < 30 W
1530E: < 25 W
(http://www.cisco.com/c/en/us/products/collateral/wireless/aironet-1530-series/data_sheet_c78-728356.html)
AP1140: 12.95 W
(http://www.cisco.com/c/en/us/products/collateral/wireless/aironet-1130-ag-series/datasheet_c78-502793.html)
So depending on the 2960 in question, I believe you may be able to power them up, do you have anything else hanging off the switch?
We had issues with lighting arrestors causing PoE failures in the past. Removing them cleared the issue.
Please rate and marked if this answers your question.

Looking for an Access Point with 2 Ethernet ports and powered via PoE

Hi Gurus,
I am looking for an Access Point with 2 Ethernet ports and the access point can be powered via PoE. I have been assigned with a requirement where the rooms need to have access point as well as an Ethernet Cable provided from the Access Point as a backup for connectivity.
The room only has one data cable coming from the main IT room as well does not have a spare power socket to power the Access Point. Will be good if it can be centrally controlled or controller based.
Any recommendations?
Regards
J

For the backup plan, the cheapest solution may be to just run a couple new cat5e drops to the room(est cost $250). If not then purchase a small Cisco POE switch for the room(est cost $2k). For wireless I would purchase a POE enabled Cisco AP. But you will need to verify the POE switch/blade you will be connecting the AP to can power the AP you buy. I got burned by that issue when we purchased some Cisco 1251 AP's with dual radios and they needed more power than our 4500 POE blades could handle. We were told we would need to purchase new 48 port 10/100/1000 blades or power injectors. Our Cisco sales vendor took the heat for that mistake.
Posted by WebUser Steven Kinney from Cisco Support Community App

G4 (10.4.11) airport (9.52) wifi connectivity issue w WPA access point

I am struggling to resolve a wi-fi connectivity issue between a G4 imac with airport card and a netgear wireless-n access point.
The set up is as follows - the broadband comes into a Netgear router (DG834Gv5)which my Intel imac connects wirelessly to. Two daughter's den is away downstairs so I run an ethernet cable from the main netgear router to a netgear Pro-safe wireless access point (WNAP210) as an extender (we live on a houseboat so there are metal bulkheads and the like inbetween.
In the den older daughters G5 wirelessly connects to the Netgear access point easily through a WPA-PSK connection.
Younger daughters G4 running 10.4.11, with original airport card running firmware 9.52 (airport admin utility 4.2) refuses with the 'wrong password' error (it isn't - I have checked 50x) or sometimes just 'there was an error joining'.
It can see the network strongly (the airport menubar icon goes full, then cuts, then flashes on, then drops) but refuses any traffic.
This G4 can however connect, weakly, with my upstairs router which is also WPA-PSK protected (same password)!
I have read all the forums on this and despite some non-expert posts muddling the issue I believe that this SHOULD be possible. Not WPA2 I know but basic WPA.
In addition the options in the netgear extender are b&g (like upstairs which works), g or n. So I have selected b&g - no difference.
Currently I have had to set a separate channel for her and leave it unsecured which isn't a long term option (I am just hoping that even the cleverest war-driver cant sneak in through the extender, back up to the traffic between my Intel and the main router !!?)
Can anyone suggest what I might be missing in the conjuration (sic, ahem) configuration settings either on the G4 or the Netgear box ?
Is it enough to turn the broadcasting of the open channel name off and so render it invisible ?
Thanks in advance for any expert person's attention

hi kathryn
did it have to be the Telekom, by all means??
anyway, first of all a link to a video where a german comedian writes a letter to steve jobs demanding he chose any carrier but the DTAG for the iPhone distribution in germany - really funny!
http://bit.ly/4B4OdQ
OK, I´m currently downloading the speedport manual from their website and will look through it, in order to see if there´s something in there..
as a first guess I´d try looking at the wireless prefs of that speedport box. I guess it supports by default 802.11a/b/g, whereas the G4 only does 802.11b (the "normal" airport). Try selecting only the 802.11b portion from the speedport (that makes networking somewhat slower for airport express computers, but shoudn´t be a problem since it´s still at least as fast as basic DSL service (11MBit vs 2 or 6 MBit)
cheers
Matt
(german in spain)

AirPort Extreme (5th Gen) WiFi access point disappears but wired ethernet is ok

My AirPort Extreme SSID and access point "disappear" randomly from available WiFi networks. I had a 1st gen AirPort Extreme and never had this problem until earlier this year. I thought it might be a failing radio in the 1st gen unit so I used it as a good excuse to get a 5th gen AirPort extreme about 3 months ago. Same problem has been occuring; unfortunately it is random and I cannot get a handle on what/when/why it is happening.
For example, my iPhone 4S was connected to the network at about 1700 today and when I next checked the phone around 2115, no wifi connection and my network was not listed in the WiFi connections. The base station is away from other wireless devices (mouse, keyboard) and is about 10 feet from the nearest PC and monitor. Both printers are accessed via ethernet, not wifi. The strange and puzzling thing is that the PC, which is connected by ethernet to the AirPort Extreme, is still connected to the internet (I can browse, check email, newsgroups, etc.).
When I run the AirPort Utility, the base station is identified (AirPort Extreme 802.11n 5th Generation), there is an appropriate IP address, Version 7.6 firmware, and MAC address is listed. However, when I attempt to Continue or do a Manual Setup, I'm prompted for the admin password, the progress bar moves during 'reading from the Apple wireless device. Please wait...,' and then the utility reports "An error occured while tryong to access the Apple wireless device. Make sure your network connection is valid and try again. Error -6722.
If I unplug, wait, and reattach the power to the base station, WiFi becomes available again. When the WiFi connection "disappears", the LED light is solid green.
Any insights are appreciated; please let me know other helpful information I can provide.
Scott

I have the exact same problem and it's driving me nuts.
I bought an airport extreme n last week and plugged it in, hooked it up to my adsl router by Ethernet, configured it to set up a new wifi network and got the green light. I use an iPhone 4, iPad 2, and Windows 7 PC with an N wifi adaptor.
The airport works fine for about 2 hours before the wireless network disappears without a trace. Green light remains on the base station and I can connect fine by Ethernet.
"it just don't make sense"
I hope it's not a windows-7-only thing, Apple.
PS. Updated firmware to the newest version, no difference.
Airport is near to a wireless phone so I set a specific wireless channel and frequency to prevent a clash. No change.

Using printer's ethernet port as an access point

Hi there,
I have an HP LaserJet Pro 200 color MFP M276nw wirelessly connected to my network. I also have an HP LaserJet 5P, which was connected to my network / wireless router via an ethernet cable using a D-Link DP-301P+ print server. Don't judge...I love that old dinosaur and I use it exclusively for all black and white printing, and it has an envelope feeder. I moved and it's no longer possible for me to have my router in the same room as my printers.
Is it possible to use the HP LaserJet Pro 200 color MFP M276nw's ethernet port as an access point for the HP LaserJet 5P using the Link DP-301P+?
Thank you in advance for your help.

Hi,
Sounds very interesting, 3:30AM now (I'm watching FIFA games), I will talk with my Networks guys when they come to work and update later.
Regards.
Updated: Talking with the Network guy, he said this may noy work and his recommendation: use LAN over power.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Can I disable my Verizon Fios Router Wireless radio, connect it to a switch and use my airport express as my wireless access point connected to an in wall ethernet port?

Here's the deal. I have a Verizon Fios MI424WR router. My house has CAT5 throughout the house. The media panel is located in the garage. I want to take the Verizon Fios Router and cannot it in the media panel so I can connect a switch to it, that way, all my CAT5 can fire throughout the house. Verizon being Verizon decided to connect the router directly in the office.
Can I go this route (Router in media panel, switch cross connect to it) and use Airport Express, connected to one of the in-wall CAT5 ports in my house and then set it up as my wireless access point to provide wifi to my portable devices (iPad, iPhone, Macbook)? Is this possible? Will Airport Express comminicate with my verizon router via ethernet in-wall? Do I have to turn off the wireless radio in the Verizon router? Any help would be greatly appreciated!

That is right, by hard wired I was just making clear wired vs wireless attachment. AirPort family of devices will only act in a repeater mode with their own family members, not FiOS routers. they have to be wired to work.
There are some useful docs you can download from Apple, Support, Manuals, Peripherals, AirPort (just follow thos links from the Support button on the top bar):
Apple AirPort Networks
Designing AirPort Networks
AirPort Express Setup Guide
The last has a diagram of what you are trying to do, though without the house wiring, etc., but the basic principle.

Strange VLAN issue on aironet access points

I'm setting up some access points for WPA. I've ran into a strange issue. The client VLAN (VLAN that the users will be put into) is 1, and the native VLAN is 10. The RADIUS server is in VLAN 1 (but I have a test RADIUS server in VLAN 10 as well). I can connect from the access point to a RADIUS server in either VLAN, and from the RADIUS servers to the access point as well. When I point to a RADIUS server in VLAN10 authentication works fine. If I point to a RADIUS server that is located in VLAN1, and I put the wireless clients in VLAN10 it works fine. But for some reason when I have the RADIUS server and the clients in VLAN (1) and the native (BVI1) interface in VLAN 10 the authentication packets never seem to get to the RADIUS server. It is as if the authentication is being sources out of the wrong VLAN. I can?t find any docs to say that this isn?t a supported configuration.

Hi Shannon,
have a look here:
http://www.cisco.com/en/US/products/hw/wireless/ps4570/products_configuration_example09186a00801d0815.shtml#apconfig
- - - Snipp - - -
Significance of Native VLAN
When you use an IEEE 802.1Q trunk port, all frames are tagged except those on the VLAN configured as the "native VLAN" for the port. Frames on the native VLAN are always transmitted untagged and are normally received untagged. Therefore, when an AP is connected to the switchport, the native VLAN configured on the AP must match the native VLAN configured on the switchport.
Note: If there is a mismatch in the native VLANs, the frames are dropped.
This scenario is better explained with an example. If the native VLAN on the switchport is configured as VLAN 12 and on the AP, the native VLAN is configured as VLAN 1, then when the AP sends a frame on its native VLAN to the switch, the switch considers the frame as belonging to VLAN 12 since the frames from the native VLAN of the AP are untagged. This causes confusion in the network and results in connectivity problems. The same happens when the switchport forwards a frame from its native VLAN to the AP.
- - - Snapp - - -
Best regards,
Frank

HT1515 My internet 3rd party access point in in the basement and the speakers I want to stream music to wirelessly are upstairs. Does Airport Express need to be connected to my 3rd party router via ethernet cable or will it stream music wirelessly?

My internet 3rd party access point in in the basement and the speakers I want to stream music to wirelessly are upstairs. Does Airport Express need to be connected to my 3rd party router via ethernet cable or will it stream music wirelessly?

Wirelessly
Just select the option to make your AirPort Express join an existing network in the setup process

Wireless Client Authentication issues when roaming Access Points (Local)

I have a Cisco 5508 with Software version 7.4.121.0 and Field Recovery 7.6.101.1.
There are a handful of clients that when roaming between AP's with the same SSID that get an authentication issue and have to restart the wireless to get back on.
From Cisco ISE
Event
5400 Authentication failed
Failure Reason
11514 Unexpectedly received empty TLS message; treating as a rejection by the client
Resolution
Ensure that the client's supplicant does not have any known compatibility issues and that it is properly configured. Also ensure that the ISE server certificate is trusted by the client, by configuring the supplicant with the CA certificate that signed the ISE server certificate. It is strongly recommended to not disable the server certificate validation on the client!
Root cause
While trying to negotiate a TLS handshake with the client, ISE expected to receive a non-empty TLS message or TLS alert message, but instead received an empty TLS message. This could be due to an inconformity in the implementation of the protocol between ISE and the supplicant. For example, it is a known issue that the XP supplicant sends an empty TLS message instead of a non-empty TLS alert message. It might also involve the supplicant not trusting the ISE server certificate for some reason. ISE treated the unexpected message as a sign that the client rejected the tunnel establishment.
I am having a hard time figuring out what is causing this. My assumption is if there were a problem with the Controller or AP configurations then it would happen to everyone. My further assumption is if the client had a problem with their laptop (windows 7) then why does work at other times? So I have checked and the ISE certificate is trusted by client.
Is something happening that the previous access point is holding on to the mac and the return authentication traffic is going to the old AP instead of the new one or something like that which is corrupting the data?
I also had this from Splunk for the same client:
Mar 5 13:44:51 usstlz-piseps01 CISE_Failed_Attempts 0014809622 1 0 2015-03-05 13:44:51.952 +00:00 0865003824 5435 NOTICE RADIUS: NAS conducted several failed authentications of the same scenario
FailureReason="12929 NAS sends RADIUS accounting update messages too frequently"
Any help on this would be appreciated. These error messages give me an idea but doesn't give me the exact answer to why the problem occurred and what needs to be done to fix it.
Thanks

Further detail From ISE for the failure:
11001
Received RADIUS Access-Request
11017
RADIUS created a new session
15049
Evaluating Policy Group
15008
Evaluating Service Selection Policy
15048
Queried PIP
15048
Queried PIP
15004
Matched rule
15048
Queried PIP
15048
Queried PIP
15004
Matched rule
11507
Extracted EAP-Response/Identity
12500
Prepared EAP-Request proposing EAP-TLS with challenge
11006
Returned RADIUS Access-Challenge
11001
Received RADIUS Access-Request
11018
RADIUS is re-using an existing session
12301
Extracted EAP-Response/NAK requesting to use PEAP instead
12300
Prepared EAP-Request proposing PEAP with challenge
11006
Returned RADIUS Access-Challenge
11001
Received RADIUS Access-Request
11018
RADIUS is re-using an existing session
12302
Extracted EAP-Response containing PEAP challenge-response and accepting PEAP as negotiated
12318
Successfully negotiated PEAP version 0
12800
Extracted first TLS record; TLS handshake started
12805
Extracted TLS ClientHello message
12806
Prepared TLS ServerHello message
12807
Prepared TLS Certificate message
12810
Prepared TLS ServerDone message
12305
Prepared EAP-Request with another PEAP challenge
11006
Returned RADIUS Access-Challenge
11001
Received RADIUS Access-Request
11018
RADIUS is re-using an existing session
12304
Extracted EAP-Response containing PEAP challenge-response
12305
Prepared EAP-Request with another PEAP challenge
11006
Returned RADIUS Access-Challenge
11001
Received RADIUS Access-Request
11018
RADIUS is re-using an existing session
12304
Extracted EAP-Response containing PEAP challenge-response
12305
Prepared EAP-Request with another PEAP challenge
11006
Returned RADIUS Access-Challenge
11001
Received RADIUS Access-Request
11018
RADIUS is re-using an existing session
12304
Extracted EAP-Response containing PEAP challenge-response
12305
Prepared EAP-Request with another PEAP challenge
11006
Returned RADIUS Access-Challenge
11001
Received RADIUS Access-Request
11018
RADIUS is re-using an existing session
12304
Extracted EAP-Response containing PEAP challenge-response
12305
Prepared EAP-Request with another PEAP challenge
11006
Returned RADIUS Access-Challenge
11001
Received RADIUS Access-Request
11018
RADIUS is re-using an existing session
12304
Extracted EAP-Response containing PEAP challenge-response
12305
Prepared EAP-Request with another PEAP challenge
11006
Returned RADIUS Access-Challenge
11001
Received RADIUS Access-Request
11018
RADIUS is re-using an existing session
12304
Extracted EAP-Response containing PEAP challenge-response
12305
Prepared EAP-Request with another PEAP challenge
11006
Returned RADIUS Access-Challenge
11001
Received RADIUS Access-Request
11018
RADIUS is re-using an existing session
12304
Extracted EAP-Response containing PEAP challenge-response
11514
Unexpectedly received empty TLS message; treating as a rejection by the client
12512
Treat the unexpected TLS acknowledge message as a rejection from the client
11504
Prepared EAP-Failure
11003
Returned RADIUS Access-Reject

Can I use the Ethernet Port for a computer when it is also used as a wireless network with an Airport Extreme as the access point for the wireless network

Can I use the Ethernet Port of the A1264 Airport Express to connect to the Ethernet port of a computer that does not have wireless capability when the Airport Express is also used on a wireless network with an Airport Extreme 5th generation as the access point for the network?
I have AE 5th gen
looking to buy (from ebay) the AEX A1264
Various computers, printers and hubs for the network
Is this possible to do?

Bob, Thanks for the info. I have read different articles that said yes, but I wanted to make sure before I commit to buy. I have an older A1084 which I could not use the Ethernet port. I know at one point I was able to when I was on 10.4. Now that I am on an Intel processor and 10.8 I am going to have to upgrade some of my Apple wireless hardware.
Thanks Again.

1300 Series Access Point/Bridge Power Injector - Using power over ethernet

Can I use power over ethernet to supply the Injector with power?

Hi Mikael,
Sorry, this will not work. Have a look at these specs;
1300 Series Power
Power
The access point/bridge receives inline power from the Cisco Aironet Power Injector (hereafter called the power injector). Dual-coax cables are used to provide Ethernet data and power from the power injector to the access point/bridge. The power injector is an external unit designed for operation in a sheltered environment, such as inside a building or vehicle. The power injector also functions as an Ethernet repeater by connecting to a Category 5 LAN backbone and using the dual-coax cable interface to the access point/bridge.
The power injector is available in two models:
Cisco Aironet Power Injector LR2 standard version (included with the access point/bridge)
48-VDC input power
Uses the 48-VDC power module (included with the access point/bridge)
Cisco Aironet Power Injector LR2T optional transportation version
12- to 40-VDC input power
Note The power injector and the power module must not be placed in an outdoor unprotected environment. The power module must not be placed in a building's environmental air space, such as above a suspended ceiling.
http://www.cisco.com/en/US/products/ps5861/products_installation_guide_chapter09186a008079b93b.html#wp1051840
Dual coaxial cable to run from the power injector to the 1300. See attached notes:
Cisco Aironet 1300 Series
Cisco Aironet 1300 Series Access Point/Bridge Power Injector
The Cisco Aironet 1300 Series Outdoor Access Point/Bridge Power Injector,converts the standard 10/100 BaseT Ethernet interface that is suitable for weather protected areas to a dual F-Type connector interface for coax cables that are more suitable for harsh outdoor environments. The Power Injector also provides power to the outdoor unit over the same cables with a power discover feature and surge protection. To support longer cable runs from your wireless network switch or router, the Power Injector LR is designed to accommodate up to a 100 meter coaxial cable run plus 100 meters of indoor cat5 cable?enabling total cable runs up to 200 meters. The Cisco Aironet 1300 Series Outdoor Access Point/Bridge ships with the Power Injector LR2 and an AC power supply.
From this link:
http://www.cisco.com/en/US/products/ps5861/products_data_sheet09186a008022551d.html
Cisco Aironet 1300 Series Outdoor Access Point/Bridge Hardware Installation Guide
Ethernet Ports
The access point/bridge dual-coax Ethernet ports consists of a pair of 75-ohm F-type connectors, linking the unit to your 100BASE-T Ethernet LAN through the power injector. The dual-coax cables are used to send and receive Ethernet data and to supply inline 48-VDC power from the power injector to the access point/bridge.
From this link:
http://www.cisco.com/en/US/products/ps5861/products_installation_guide_book09186a00804d3095.html
AIR-PWRINJ-BLR2
F-Type Connectors
Dual coaxial cable carries full-duplex Ethernet, DC power, and full-duplex console port (RS-232 connection)
From this link:
http://www.cisco.com/en/US/products/ps5861/products_data_sheet09186a00802252e1.html
Hope this helps!
Rob

Making my powerbook a wifi access point with ethernet

i have ethernet plugged into my powerbook g4 12' and i would like to make an access point for my psp. ive seen this done before but i have no idea how to do it

Click here and follow the instructions.
(25674)

Access point ethernet issue

Similar Messages

Maybe you are looking for