Access Point not connecting with 1G ethernet

HI everyone.
I just noticed this. I have different series of AP , 1142 , 1252 , 3500 , 3700. it is happening on any series. if I set the duplex and speed to Auto some of my AP are connecting with 100mb not 1Gps.
if I set duplex to full and speed to 1000 then the AP shows not connected on the switch and the AP it self is blinking like a Christmas tree!
I have different series I switches as well and it happening on all of them. they are Gig
this is the 3850 series out put of the interface
description Class7.1A
switchport access vlan 10
switchport mode access
spanning-tree portfast
end
speed and duplex is auto and it is connected with 100mb!
any comment appreciated

Hi my friend Manannalage
the switch ios is 03.03.00.SE
i have other APs (same series) running on 1G on the same switch
here is the proof :)
can it be the cable quality dropping from 1000 to 100? I'm going to un-mount the AP from the wall and connect it directly to the switch to see what will happen
Gi1/0/23 connected trunk a-full a-1000 10/100/1000Ba
seTX
Gi1/0/24 connected trunk a-full a-1000 10/100/1000Ba
seTX
Gi2/0/1 Class8.1B connected 10 a-full a-1000 10/100/1000Ba
seTX
Gi2/0/3 AP connected 10 a-full a-1000 10/100/1000Ba
seTX
Gi2/0/10 Class8.1A connected 10 a-full a-1000 10/100/1000Ba
seTX
Gi2/0/11 Class8.3 connected 10 a-full a-1000 10/100/1000Ba
seTX
Gi2/0/12 AP connected 10 a-full a-1000 10/100/1000Ba
seTX
Gi2/0/15 Class8.2 connected 10 a-full a-1000 10/100/1000Ba
seTX
Gi2/0/16 AP connected 10 a-full a-1000 10/100/1000Ba
seTX
Gi2/0/18 AP connected 10 a-full a-1000 10/100/1000Ba
seTX
Gi2/0/21 AP connected 10 a-full a-1000 10/100/1000Ba
seTX
Gi2/0/22 AP connected 10 a-full a-1000 10/100/1000Ba
seTX
Gi2/0/23 connected trunk a-full a-1000 10/100/1000Ba
seTX
Gi2/0/24 connected trunk a-full a-1000 10/100/1000Ba
By the way , now I have a nightmare every night because of you :) im like oh you are not updating your website any more :) thanks for the us full stuff you post there.

Similar Messages

Access points not registering with WLC

Hi all,
I have a 5508 WLC in LAG mode and have 14 1231G WAPs connected to it already. However I still have to migrate 9 more WAPs from my old 4404 controller to the new 5508 controller. I cannot get remaining 9 WAPs to register with new WLC. I found following debug message from the WLC. My WLC license is valid for 50 APs. Have any of you guys seen this? What am I doing wrong here? Any lead is much appriciated.
I have LAG setup with 2 ports out of 8 ports. Don't understand why it's giving error of not having enough capacity.
Any advice is much appriciated. Thanks in advance.
*spamApTask4: May 21 18:58:29.468: 00:23:04:c9:72:00 Echo Timer Expiry: Did not receive heartbeat reply from AP 00:23:04:c9:72:00 (10:4:12:26/36602)
*spamApTask0: May 21 18:58:50.588: 00:13:60:7e:28:30 Join Priority Processing status = 0, Incoming Ap's Priority 0, MaxLrads = 50,joined Aps =14
*spamApTask0: May 21 18:58:50.588: 00:13:60:7e:28:30 Refusing Discovery Request from AP 00:13:60:7e:28:30 - no AP manager with available capacity
*spamApTask0: May 21 18:58:50.588: 00:13:60:7e:28:30 Join Priority Processing status = 0, Incoming Ap's Priority 0, MaxLrads = 50,joined Aps =14
*spamApTask0: May 21 18:58:50.588: 00:13:60:7e:28:30 Refusing Discovery Request from AP 00:13:60:7e:28:30 - no AP manager with available capacity
*spamApTask0: May 21 18:59:00.589: Could not find BoardDataPayload
*spamApTask0: May 21 18:59:00.636:
*spamApTask0: May 21 18:59:05.593: Could not find BoardDataPayload
*spamApTask0: May 21 18:59:05.639:
*spamApTask0: May 21 18:59:53.564: 00:13:60:7e:28:30 Join Priority Processing status = 0, Incoming Ap's Priority 0, MaxLrads = 50,joined Aps =14
*spamApTask0: May 21 18:59:53.565: 00:13:60:7e:28:30 Refusing Discovery Request from AP 00:13:60:7e:28:30 - no AP manager with available capacity
*spamApTask0: May 21 18:59:53.565: 00:13:60:7e:28:30 Join Priority Processing status = 0, Incoming Ap's Priority 0, MaxLrads = 50,joined Aps =14
*spamApTask0: May 21 18:59:53.565: 00:13:60:7e:28:30 Refusing Discovery Request from AP 00:13:60:7e:28:30 - no AP manager with available capacity

Guess the SSC got corrupted..
Run the command "debug pm pki enable" on the WLC, copy the SSC and paste it on the WLC and see if that helps.. here is the link to do the same!!
http://www.cisco.com/en/US/products/ps6366/products_configuration_example09186a00806a426c.shtml
Lemme know if this answered ur question and please dont forget to rate the usefull posts!!
Regards
Surendra

Define access point to connect?

A couple of applications on my phone, particularly Ovi Maps keep doing this and it's getting REALLY annoying.
Start using the application, it comes up with the following:
"Network connection required.Define access point to connect?
Then it'll give me a selection from a list of my networks various protocols.
It will regularly ask me again and again while the app is running, often coming up in front of other applications i am using at the time!
How can I stop this?
I don't want to have to define anything for specific applications. I want my phone to connect in one of two ways without my input:
1. If I am within range of a Wifi connection it knows, connect via that.
2. If not, connect via 'O2 Active'
Is there a way I can set this so my phone just does the above and never asks again?

jezston wrote:
A couple of applications on my phone, particularly Ovi Maps keep doing this and it's getting REALLY annoying.
Start using the application, it comes up with the following:
"Network connection required.Define access point to connect?
Then it'll give me a selection from a list of my networks various protocols.
It will regularly ask me again and again while the app is running, often coming up in front of other applications i am using at the time!
How can I stop this?
It is the Assisted GPS positioning method access found in Menu > Settings > Application Settings > Positioning > Positioning server use which keeps asking for a Network access point not OVI Maps application itself which may be set "Offline" or "Online".
If you have not set "Save location info" = No - in Camera > Options > Settings - you may get the same response.
Happy to have helped forum with a Support Ratio = 42.5

Access Points not overwritten when restoring a bac...

Hi people,
Seems like the new and still buggy firmware of the E70 has another problem.
Before restoring a backup, if you do not remove the Access Point definitions (only operator Access Points, not Wi-Fi or others), the restore does not overwrite the definitions and makes new copies of the Access Points.
That would be OK if we could remove the extra Access Points but we cannot. When you delete one of the copies, it seems like it is removed but its definition is still somewhere on the phone, so while "Connection Settings" program cannot see it, all programs that use Access Points can see it (but cannot use it because it is a stale record).
Does anyone know where this info is stored so, if I forget to remove them before restoring a backup, I can remove them afterwards?
Kerem Erkan
IT Professional
E70 (2.0618.07.10 - 31.08.06 RM-10)

Welcome to the many problems of the LAPAC1750. I finally gave up and went with Ubnt. Uptime is at 75 days now and would've been longer if not for a firmware update.
The LAPAC had good range and worked well when it worked, but it's unstable to be marketed right now. Hopefully Linksys issues a firmware update to fix everything.

Access Points not joining WLC

Hello All,
I am trying to deploy several AIR-CAP3502E-E-K9 access points from a cisco 5508 wire lan contoller running ver 7 code. However iam having difficulty regiserting the access points with the WLC. The wlc is connect to a 3650 switch, and each access point is connected to a 2960 switch.
Problem Solved. A bad update was not allowing the access points to get their correct firmware.

You need to provide what Leo stated, that would help a lot. Anyways you can't telnet or ssh into a capwap AP if it has not joined the WLC. So that being said, provide the info Leo requested and then console into the ap and provide use with output from the console. Make sure you reboot the AP and then start capturing the output for around 5 minutes.
Sent from Cisco Technical Support iPad App

HELP! Ovi Suite "Packet Data Access Point Not Vali...

So i downloaded Ovi suite to get internet from my phone i have a Nokia 3711 and when i try to connect i get this message on my phone "Packet data access point not valid" what does this mean? and how can i fix it? I have unlimited internet data thing..

I guess you can call up your service provider customer service and ask them to re-send the settings!

My itunes on a windows 7 pc with dsl connection will not connect with the itunes store

my itunes on a windows 7 pc with dsl connection will not connect with the itunes store. Any suggestions about why not or how to get it to connect?

After reading the whole post, I still don't capture the exact error message or code from it when you failed to install Office 2013.
The only clue is that "bootstrap loader error" ...
It seems that you want to upgrade Office 2007 to new Office 2013, by default, we could complete the uninstall previous Office version and install the new Office in the installation wizard.
At this point, if you get the install source through CD or other media. I recommand that we copy/paste the installation to local drive. Then turn off all of anti-virus and firewall, begin to setup in
Windows clean boot mode.
Please use a setup log to troubleshoot setup problems in Office if the installation problem still occurs.
http://support.microsoft.com/kb/826511/en-us
Tony Chen
TechNet Community Support

My Contacts app for macbook pro will not connect with my yahoo and keeps asking for password.

My Contacts app for macbook pro will not connect with my yahoo account and repeatedly asks for yahoo password, any soliutions to this?

This is due to a change in Yahoo's security settings. You need to go into your Yahoo account settings and create a special App Password, then use that password in Contacts to access your account. Same goes for Calendar.

Itunes can not connect with the Itunes store

Every time I try to connect to the ITunes Store an error pops up : Itunes can not connect with the Itunes store. I have downloaded the updated software and have access to the internet. Anyone ever run into this problem?

If it still has problems after trying the steps above, try resetting Winsock. It looks like it worked for a few people in this thread -> With iTunes 10.4 I can access iTunes store.
MTG68 wrote - In windows 7, click on your start menu, go to accessories, right click on the command prompt icon and choose "run as administrator". Once it opens, type in the following command...
netsh winsock reset
hit enter and it should say something like winsock reset successful now reboot your computer.

Facebook setting is not connecting with server Facebook is not connecting with server

Facebook is not connecting with server

May friend i try that one but the problem for may ipad air is on #2 the disable facebook. There is no button, nothing on the screen, only this " applications that have requested access to your facebook account will be appear here" that the only on the screen, no button to off on facebook.. Can you help me about this pls?

Hi, my MacBook Air is not working anymore if it's not connected with the power cable. It's pretty new so I can't imagine that the battery is dead already. Why can't I use my MacBook Air without the power cable even though I charged it for hours?

Hi, my MacBook Air is not working anymore if it's not connected with the power cable. It's pretty new so I can't imagine that the battery is dead already. Why can't I use my MacBook Air without the power cable even though I charged it for hours?

Please take the Mac to Apple store to have it checked out.
Genius Bar reservation
http://www.apple.com/retail/geniusbar/
Best.

Problems setting up my TC. Have just bought new iMac(OS 10.6.8) and TC. I set it up. iMac cannot find it. I have tried direct connection with an ethernet cable to Mac or my wireless router but nothing. Just a flashing orange light. Help for a simpleton p

Problems setting up my TC. Have just bought new iMac(OS 10.6.8) and TC. I tried to set it up. iMac cannot find it. I have tried direct connection with an ethernet cable to Mac or direct to my wireless router but nothing. Just a flashing orange light. Help for a simpleton please. Have tried reseting TC, but to no avail.

Just updated from 10.6.7 ---> 10.6.8 and had the same issue. Despite having done a clean install from 10.6 and got everything back off my TC, now Time Machine can't find it!
Green light is on, ethernet cable conected, network CP says its conected but nothing. Airport Utility can't find it. Hit reset button, Orange flashing light but still no show in Airport Utility.
But I know its there, as rebooting from 10.6 SL disk shows the backups are still ok?
Hmm, ideas anyone?
SBB

I have an account for apple but this is not acceptable for i cloud. It say it is correct ID and password but this is not icloud account. So my phone can not connect with my computer and not synchronization too

I have an account for apple but this is not acceptable for i cloud. It say it is correct ID and password but this is not icloud account. So my phone can not connect with my computer and not synchronization too. Last a few months i have not use this phone. Just i start to use again. So most probably i gave my old mail address as a ID or password. So how can i clearing this subject. regards

ErolSinan wrote:
... there is no button for update between the About and Usage buttons in the General. ...
Correct. That is only a feature of iOS 5 or later...
ErolSinan wrote:
... yes my phone is 3G.
then it can only go as far as iOS 4.2.1

I recently updated my MacBook Pro to the new software, and now my iMessage and my FaceTime are not connected with my computer. How do I get them to match so that I would be able to use my cellphone number?

I recently updated my MacBook Pro to the new software, and now my iMessage and my FaceTime are not connected with my phone number like it is supposed to be. How do I get them to match so that I would be able to use my cellphone number on my notebook?

To reset any OS X program just go to the folder and trash the affected files.
Open a new Finder Window
Click "Go" in the above status bar
Click and HOLD the "option/alt" key and you will see "Library" now show in the above list
Click Library while still holding the option/alt key and a new window will open with all of your system files
Go to the preference file (NOT Preference Panes)
Locate a file named <com.apple.FaceTime.bag.plist>
Locate another file named <com.apple.FaceTime.plist>
Locate the file <com.apple.iMessage.bag.plist>
Drag the files to the trash
Delete the trash
Close FaceTime and iMessage if not already closed
Relaunch FaceTime and iMessage from Applications folder
This should reset the program back to default. You will have to put your information back into the program but it should work.
Good Luck.

My iPhone 4s will not connect with my home WiFi network. I have ios6 on my phone. I have updated my IMac and my MacBook Pro with iOS 10.8.2. Anyone have any suggestions? It was connecting with no problems prior to updating my two computers.

My iPhone 4s will not connect with my home WiFi network. I have ios6 on my iPhone. The connection was working perfectly before I updated my IMac and my MacBook Pro to ios 10.8.2. I have had ios6 since I purchased the phone a couple of months ago. It searches for a network and finds them, but when it asks for my password, it will not accept the password. Have never had this happen before.

Hello krosebear,
Thank you for using Apple Support Communities.
If you are having difficulties connecting your iPhone to a Wi-Fi network, the following article should provide troubleshooting that should help you resolve the issue.
If your iPhone, iPad, or iPod touch won’t connect to a Wi-Fi network - Apple Support
Regards,
Jeff D.

Access Point not connecting with 1G ethernet

Similar Messages

Maybe you are looking for