Access point problem... help

i have an access point which is not suppose to be in the native vlan, the port which is connected to the access point has no trunk.
when i checked the native vlan, this error prompted...
%SYS-4-P2_WARN: 1/Tag 1 on packet from <mac add> port 1/3, but port's native vlan is 2
but when i unchecked it, the connection lost between AP & switch...
what actually happened? can anyone plz help me?

Hi,
the connected switch a Cisco Switch? If yes do you have configured a "switchport access vlan xx"?
If the connected Switch is not a Cisco i had a problem similiar to yours and fixed it with the setup of the used VLAN (in my case VLAN 10) as Native VLAN in the AP.
Maybe you should setup the Native VLAN to 2 in your AP Config.
I Hope that helps.
Best regards,
Frank

Similar Messages

E75 Email (Access Point problem)

Hi,
I've setup nokia email without any problem using my WiFi and it was synchronizing without a problem. Since then I've I'm unable to change the Access Point to my Mobile provider. I keep getting "Server not found", even though the server name is still properly configured (netac3.vie.hosting.com). Can anyone help?
Regards,
Nuno

Sorry when I wrote this was in Houston at the Continental Presidents club being yelled at... sorry
The problem still exists, with no solution found so far, can anyone help?

6600 access point - pain / help me

I've just got me hands on a 6600 and it keeps asking me to select an access point (ie: GPRS or my provider) if I say yes it dials up the number - if I say no (cancel) it go's away for about a minute then "pops" back up - can anbody tell me how to STOP it poping back up!!! its driving me round the bend
ps - I have looked in the providers manual (not a Nokia manual) and its no help.
Thanks

Does this help: http://discussions.nokia.co.uk/discussions/board/message?board.id=messaging&message.id=89&query.id=0...

LAPAC1750 Access Point Problem

I have a device (Sony Xperia Z1 Compact) which cannot connect to the Access Point. The device can connect to other Access points (tried Motorola, Fritzbox, Cisco) without any problems.
It does not matter what setting I configure on the LAPAC1750. It does not work for the Sony Xperia Z1 Compact.
Any idea?
Solved!
Go to Solution.

Did Linksys ever get a resolution back to you? I noticed they have not posted any new firmware since June (stil 1.05.00), and from other threads on other products it seems this is typically resolved with a firmware update. I bought three LAPAC1750s to install in our large home on each of our three floors, and every device (PC and Mac laptops, iPad, Kindle Fire HD, iPod, iPhones) can connect to them EXCEPT my HTC One M8 running Android 4.4.4. Shows same behavior you are seeing, will try to connect and then just disable it. Same behavior on both 2.4GHz and 5GHz.

Access point problem

I installed a MIDlet in my nokia 6600. When application tries to open an Http connection I have to select the access point. In my mobile I have set my default access point. Still it asks me to select access point everytime. How can I make the access point selection automatic? Can somebody please help me?
Regards to everyone.

2.2mb of free space seems to be more than enough for you to create a new access point, hmm.. strange.
Would you want to try freeing some memory space by moving gallery items from the phone memory to the memory card? If it still don't work, restoring of factory settings might work but all data will be lost if you choose to restore all. The last resort would be to have a software reflashing which can be done either via the NSU or at the service point.

Search function + Access Point problem

I access the Google Search from the Search software pre-installed with the N97 and set the Network destination as "Internet". I got 3-4 access points under "Internet" (4 if there is a saved wifi point).
I have no problem at all conducting the search as it would use the 1st access point under Internet, but when I try to view one of the search results, which is opened in the native broswer of the phone, it would use another access point (the 3rd priority access point) to connect.
Does anyone have any clues on how to resolve this?

Hi, not sure if this will solve your problem but try:
Select 'Web'
Once there Click 'Options'
Select 'Settings'
Select 'General'
Select 'Access Point'
Choose 'Ask when needed'
Hope this helps

S110 wifi access point problems

I am trying to connect my camera to wifi by adding it as an access point. I typed in the password correctly but it keeps telling me unable to connect. Please help! Thanks in advance!

Hello Rainingmisery,
Rather than going through the steps here through the Canon Forum, we would actually like to direct you to our web site where we have a dedicated section on getting the PowerShot S110 connected wirelessly.
We anticipated that our customers would like more in depth information on wireless connections and as such made a specialized support site complete with videos and articles dedicated to this camera.
The main PowerShot S110 wireless help web site is here.
Here you will see specific videos and at the bottom are links to articles for making wireless connections through WPS or Manual. We think you will find this quite useful in setting up the camera wirelessly.
If you need further assistance or would like to speak to someone directly, we have our world class technical support team at your disposal. Get in touch with us through our service and support site!
Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well.

WAP2000 Wireless-G Access Point (Setup Help)

Hi,
We have a wireless-g access point typically (and previously, in this case) used for a small business. We were given the device for free and wanted to reset the device to use as our wireless router at home. First and foremost, can a wireless access point double as a home wireless router? I was told that only one computer/laptop at a time can connect to a wireless access point, unlike a wireless router which allows multiple devices to connect to a wireless home network at a time? Is this true?
Second, because the device is not new, we no longer have the setup instructions. Upon resetting the device (holding down the reset button for 10 or more seconds), we were unable to access the WAP2000 online setup page for a username and password. The device is being picked up by our macbooks and shows up in the Airport as "linksys-g." However, we are unable to access the setup page or communicate with the access point. We have tried typing http://198.162.1.1/ in our address bar, but have had no luck.
Do you have any suggestions as to how to set up the device? Also, can this device double as a router that will allow multiple laptops and devices (i.e. sony playstation) to access and use the wireless network simultaneously.
Thank you for your help.

Sam,
First yes you won't to factory reset the unit. You should hold down the reset button longer than 30 seconds and no longer than 45.Once this is back to factory default, the current ip address should be 192.168.1.245 , you will need to statically assign your pc an address in 192.168.1.1 /24 range and make sure you are plugged directly into WAP2000. Now you should be able to access the AP. Default username = admin password = admin
http://www.cisco.com/en/US/docs/wireless/access_point/csbap/wap2000/quick_start/guide/WAP2000_Quick_Start_Guide.pdf
Above is a quick start guide for reference.
Now just configure accordingly.
Thanks,
Jasbryan
Cisco Support Engineer
.:|:.:|:.

3600 Series Access Point Problem

Have a AIR-CT5508-K9 Controller running 7.0.116.0 software.
Just purchased 3 AIR-CAP3602I-A-K9 access points.
When these try to join the controller we receive the following error message.
%CAPWAP-3-UNSUPPORTED_WLC_VERSION: Unsupported version 7.0.116.0 on WLC Plt-72-Controller-1
Do the 3600's require a certain revision of code?
Also I read were the 3600's require a GE connection. Will they work on a FE connection?
Please advise.....................

Yes, you need to be funning 7.2 code for the 3600 to join and work.
Make sure you check the release notes for hte supported AP, incase you are running any that are not supported in 7.2
Steve

Just Moved, Want to Use My e3000 as just an access point NEED HELP

Hey, I just moved into a house the other day, the router/modem is upstairs, my desktop/xbox only has wired capabilities, and my laptop has wifi. I was trying to just make a bridge with my my laptop to my desktop while i try and figure out how to get all my stuff working again, but found out the jack in my laptop is broken, so it only has WIFI.
My question is, am I able to use my e3000 to connect to their wifi signal via wifi, in which i can just run a cable to my xbox and desktop within the room?
I cant run 2 cable from upstairs to downstairs for my desktop/xbox, so was hoping this was possible. thanks

Yes, and you can turn wi-fi access on after enabling airplane mode if you want or need internet access via an available wi-fi network.

Linksys Wireless-B Router & Access Point question

Ok, I have a Linksys wireless B router (cant remember the model name off of the top of my head) and it connected to a desktop that I have. I just purchased a Buffalo Wireless-G MIMO router which has the ability to act as an access point. I was wondering if I set the Wireless-B router up to my desktop where my modem is, and then turn on the Access Point feature with my Buffalo router, would the two brands work together or no? Also, if they did work and the Buffalo router acted as an access point would I be able to connect my PS3 via one of the ethernet port on the back of the Buffalo access point? Help would be greatly appreciated, thanks.
I just purchased this Buffalo router after returning the Linksys Wireless-G with SpeedBooster and having numerous problems with my Verizon DSL (Westell 6100 modem).

Yes you can. Here is a LINK to use as a reference. The only thing you will run into is the routers IP's may be different so make sure they are in the same range. Example router 1:192.168.1.1 and router 2:192.168.1.2 but it may vary depending on what you want your private IP range to be.
The router you want to set as a AP make sure it has the latest firmware and has the SSID/security all set up. Make sure the IP for the router is set then disable the DHCP. Then connect router 1 via numbered port to the number 1 port of the second router.
Message Edited by Ikester on 07-16-2007 09:43 AM
Richard Aichner (Ikester)

MSI AP11b wireless IEEE802.11b Access Point

hi to all msi admin there and members.
im new here in this forum can anyone help me to answer my question about MSI AP11b wireless IEEE802.11b Access Point product.
I'm planning to buy MSI AP11b wireless IEEE802.11b Access Point to use my new laptop with wireless and enable me to share my internet using ap11b accesspoint..My problem is im using an usb adsl modem with (no Rj45 jack)only USB. so i can only connect my adsl modem to my desktop pc and i want to share my internet to my laptop using the wireless connection,but the problem is i dont know if this MSI AP11b wireless IEEE802.11b Access Point can help me to share my internet connection over my laptop. i have an idea and i dont think if this would work ex. if i buy MSI AP11b wireless IEEE802.11b Access Point and right after then, as usual my desktop pc is currently connected in the internet using my usb adsl modem, i want to use my desktop pc as a server using internet connection sharing(ICS) (im using WinXP) i have ethernet card that is built on my board and which ap11b available is RJ45 JACK im gonna plug my rj45 and connect it to rj45 jack of ap11b.
is this possible that im going to use my desktop pc to become serve because my adsl modem(USB)(no rj45)r and share my internet using ap11b wireless accesspoint on my wireless laptop?
anyone i need some good advice in this cases...

yes, you could use ap11b to become server and share internet for your wireless laptop.
You have to connect the ap11b to your desktop PC ethernet card via RJ45.
If the ASP can give you more than 2 IP, you can choose "Bridge model" in the "Network Connections" setup.
If the ASP only give you 1 IP, you should share the Internet Connection.
Network connections-->Local Area Connection-->right click-properties-->Advanced-->click "Allow other network users to connect through this computer's Internet connection"

Nokia Email Access Point Configuration Disappeared

I`ve just upgraded to the new Nokia Email client on my N95-1 (model RM-159). It says it's version 9.04 (21).
Since upgrading, I haven't been able to configure the Access Point to be used by the email app, which used to be under General|Service Info. This is quite important to me, since I only want to let the app work when using WiFi.
Does anyone know what happened, or how can I fix it ?

This works for the E71: for the time being a workaround for the access point problem:
I set my SmartConnect connection (you can only download this from the Download icon on your phone) group as the default APN, I have the client using Wifi if available and the cellular network if not. This MUST be configured at initial setup, ie when you install Nokia Messaging, change it from "default" to the SmartConnect access point group.

Nokia email - access point

I have an N96 with S60 r3 fp2. It supports "destinations" (ie access point groups) as well as the concept of a "default" access point (group).
Only "new" apps use these capabilities. The internal imap client seems to be ok with default, but "nokia messaging" is not and will only allow a specific AP to be selected.
Since I have trouble with 3G/GSM at work I roam onto WIFI for other apps. NOkia messaging needs to do the same.
Ideas?

This works for the E71: for the time being a workaround for the access point problem:
I set my SmartConnect connection (you can only download this from the Download icon on your phone) group as the default APN, I have the client using Wifi if available and the cellular network if not. This MUST be configured at initial setup, ie when you install Nokia Messaging, change it from "default" to the SmartConnect access point group.

CISCO Aironet access point - not able to connect by user.

Hi,
I have CISCO Aironet access point C1130 in my network , but not able to connect by users, I can see below logs from access point. please help on this.
Jun 13 17:50:10.686: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000
Jun 13 17:50:10.686: RADIUS: Retransmit to (20.33.100.11:1645,1646) for id 1645/247
Jun 13 17:50:15.678: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000
Jun 13 17:50:15.678: RADIUS: Retransmit to (20.33.100.11:1645,1646) for id 1645/247
Jun 13 17:50:20.544: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000
Jun 13 17:50:20.544: RADIUS: Retransmit to (20.33.100.11:1645,1646) for id 1645/247
Jun 13 17:50:24.832: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000
Jun 13 17:50:24.832: RADIUS: Retransmit to (20.33.100.11:1645,1646) for id 1645/247
Jun 13 17:50:29.741: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000
Jun 13 17:50:29.741: RADIUS: Fail-over denied to (20.33.100.11:1645,1646) for id 1645/247
Jun 13 17:50:29.741: RADIUS: No response from (20.33.100.11:1645,1646) for id 1645/247
Jun 13 17:50:29.741: RADIUS/DECODE: No response from radius-server; parse response; FAIL
Jun 13 17:50:29.741: RADIUS/DECODE: Case error(no response/ bad packet/ op decode);parse response; FAIL
Jun 13 17:50:29.741: dot11_auth_dot1x_parse_aaa_resp: Received server response: FAILOVER_RETRY
Jun 13 17:50:29.742: dot11_auth_dot1x_parse_aaa_resp: found eap pak in server response
Jun 13 17:50:29.742: Client 5864.6c67.3718 failed: EAP reason 0
Jun 13 17:50:29.742: dot11_auth_dot1x_parse_aaa_resp: Failed client 5894.6b37.3518 with aaa_req_status_detail 0
Jun 13 17:50:29.742: dot11_auth_dot1x_run_rfsm: Executing Action(SERVER_WAIT,SERVER_FAIL) for 5894.6b37.3518
Jun 13 17:50:29.742: dot11_auth_dot1x_send_response_to_client: Forwarding server message to client 5894.6b37.3518
Jun 13 17:50:29.742: dot11_auth_dot1x_send_response_to_client: Started timer client_timeout 30 seconds
Jun 13 17:50:29.743: dot11_auth_dot1x_send_client_fail: Authentication failed for 5894.6b37.3518
Jun 13 17:50:29.743: %DOT11-7-AUTH_FAILED: Station 5894.6b37.3518 Authentication failed
Regards,

Hi Niham,
You can try few things to troubleshoot this -
1. check the reachability of Radius server from your wlc (ping).
2. verify the IP address of Raduis server configured on wlc.
3. wlc in the Radius server ?
4. Shared Secret must be same on wlc and in raduis server.
Plz do not forget to rate useful post.
Thanks

Access point problem... help

Similar Messages

Maybe you are looking for