Access point register on anchor wlc in DMZ
Hello,
I have an environment in which two WLC 4400 are connected to an anchor WLC 4400 in DMZ, This WLC in DMZ pass the Guest Wlan to other two WLC and terminate tunnel CAPWAP. The Ap in the remote sites, that are configure to register to WLCs in the remote sites, usually are registered on the two WLCs but sometimes they register to WLC in DMZ, how is possible if between WLC in DMZ and other WLC there is a firewall that block all the traffic except CAPWAP traffic?
If I reboot the APs they register on the two correct WLCs in remote sites.
Thanks
AP also uses CAPWAP. you should only allow capwap connection from internal controllers only on the fw.
Similar Messages
-
Limiting access points joining a specific WLC
Hello Cisco Forum Team!
I am currently installing a new WLC in a VLAN/IP segment that already has WLCs configured and access points registered. I do not want existing ap's on this VLAN to join this new WLC. Which is the best way to limit ap's joining this new WLC?
I am thinking of some sort of AP authorization list but by IP address instead of MAC address due to the high amount of ap's currently registred on the existing WLCs (approx. 300 ap's).
Thanks in advanced for your support!AP authorization list would work but you have to use MAC address & cannot use IP address for that. Once you enable AP authorization you can add AP mac to the list like below using CLI.
(5508-1) >config auth-list add mic <AP1 mac>
(5508-1) >config auth-list add mic <AP2 mac>
(5508-1) >config auth-list add mic <APn mac>
HTH
Rasika
**** Pls rate all useful responses **** -
Access Point Secured Registration to WLC
Hello
Which option on WLC ensure that any AP registering to WLC should be first authenticated with a password and then register to a WLC
cheers
CPHell there ...
Take a peek at the below link.. I think this is what you are asking ?
Lightweight Access Point (LAP) Authorization in a Cisco Unified Wireless Network Configuration Example
http://www.cisco.com/en/US/customer/products/ps6366/products_configuration_example09186a00808c7234.shtml -
Access points connect to wrong WLC
Hello everybody,
I have a problem with some access point.
We have two WLC's one AIR-CT5508-K9 and one AIR-WLC4404-100-K9.
now i have 6 access points that don't register anymore to the right controller.
in high availability i have set the right name of primary controller and also the correct ip address, but somehow they keep registering to the other controller.
Does someone know how i can fix this problem.
info:
AIR-CT5508:SEDA-PM_Line_1
WLC4404: SEDA-PM_Office_1
6 accesspoints are connected to SEDA-PM_Line_1 but they should be connected to SEDA-PM_Office_1
settings in AP are correct in my opinionhere is the information,
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.0.116.0
RTOS Version..................................... 7.0.116.0
Bootloader Version............................... 3.2.195.10
Emergency Image Version.......................... N/A
Build Type....................................... DATA + WPS
System Name...................................... SEDA-PM_Office_1
System Location.................................. Mao, Brazil
System Contact................................... Network_Admin
System ObjectID.................................. 1.3.6.1.4.1.14179.1.1.4.3
IP Address....................................... 105.103.112.5
System Up Time................................... 8 days 15 hrs 9 mins 55 secs
System Timezone Location.........................
Configured Country............................... US - United States
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +38 C
--More-- or (q)uit
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Disabled
Number of WLANs.................................. 13
Number of Active Clients......................... 132
Burned-in MAC Address............................ 00:22:55:91:2B:C0
Crypto Accelerator 1............................. Absent
Crypto Accelerator 2............................. Absent
Power Supply 1................................... Absent
Power Supply 2................................... Present, OK
Maximum number of APs supported.................. 100
(Cisco Controller) >show time
Time............................................. Thu Jan 9 07:58:29 2014
Timezone delta................................... -4:0
Timezone location................................
NTP Servers
NTP Polling Interval......................... 86400
Index NTP Key Index NTP Server NTP Msg Auth Status
1 0 211.189.10.2 AUTH DISABLED
AP information
Warehouse_AP-3#sh version
Cisco IOS Software, C1240 Software (C1240-K9W8-M), Version 12.4(23c)JA2, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Wed 13-Apr-11 12:58 by prod_rel_team
ROM: Bootstrap program is C1240 boot loader
BOOTLDR: C1240 Boot Loader (C1240-BOOT-M) Version 12.4(13d)JA, RELEASE SOFTWARE (fc2)
Warehouse_AP-3 uptime is 18 hours, 16 minutes
System returned to ROM by power-on
System image file is "flash:/c1240-k9w8-mx.124-23c.JA2/c1240-k9w8-mx.124-23c.JA2"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-LAP1242AG-A-K9 (PowerPCElvis) processor (revision A0) with 27638K/5120K bytes of memory.
Processor board ID FTX1233B943
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from power-on
LWAPP image version 7.0.116.0
1 FastEthernet interface
2 802.11 Radio(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:1D:70:96:64:A0
Part Number : 73-9925-07
PCA Assembly Number : 800-26579-06
PCA Revision Number : A0
PCB Serial Number : FOC12320AKT
Top Assembly Part Number : 800-29151-03
Top Assembly Serial Number : FTX1233B943
Top Revision Number : A0
Product/Model Number : AIR-LAP1242AG-A-K9
Configuration register is 0xF
Warehouse_AP-3#sh ip interface brief
Interface IP-Address OK? Method Status Protocol
Dot11Radio0 unassigned NO unset up up
Dot11Radio1 unassigned NO unset administratively down down
FastEthernet0 105.103.27.19 YES other up up
Warehouse_AP-3#sh inventory
NAME: "AP1240", DESCR: "Cisco Aironet 1240 Series (IEEE 802.11a/g) Access Point"
PID: AIR-LAP1242AG-A-K9, VID: V03, SN: FTX1233B943
there are 7 AP's that not register to the right controller some are different models:
Warehouse_AP-1 - AIR-LAP1242G-A-K9
Warehouse_AP-3 - AIR-LAP1242AG-A-K9
Warehouse_AP-5 - AIR-LAP1242G-A-K9
Warehouse_AP-6 - AIR-LAP1242G-A-K9
Warehouse_AP-7 - AIR-CAP3502I-T-K9
Warehouse_AP-9 - AIR-LAP1242AG-A-K9
Warehouse_AP-10 - AIR-LAP1242G-A-K9
Thank you for your help!! -
WCS displays Access Point as disassociated but WLC shows as associated
Hi all,
I have a WCS ver 7.0.172, a 5508 WLAN Controller with ver 7.0.116.0. At this WLC 21 Access Points (AIR-LAP1131AG-E-K9 ) were associated. As well I have one CleanAir Access Point (AIR-CAP3502E-E-K9) is associated.
And now ... my problem:
every time the WCS got a critical error and reports that the AP is disassociated from Controller. But if I take a look to the WLC the AP is associated and works at local mode and have two clients associated.
I cleared the alarm - a few minutes later the alarm will be reported again. Same result if I delete the alarm.
Could anybody give support for that issue.
Thanks and regards
HolgerHi Holgerseiler,
Have you got any information/solution on this issue?
I also have same kind of issue. I have a WCS with version 7.0.172.0, and around 25 WLCs (version7.0.116.0, in which i checked) and totally around 1000 APs are assiociated in wireless network.
Some error messages are coming on my WCS device like
"AP disassociated from Controller [ip]"
Here AP name and WLC ip address will change randomly, but there is no impact on my network.
Thanks in advance
Sangeeth BS -
Trying to get home sharing working on a corporate wireless network. Cisco wireless.
WLC5508 controller
Cisco 3502 access points
All apple devices on same WLAN - security WPA2-PSK
ITunes account up to date
All devices laterst software.
Can ping apll tv from laptop
can ping apple tv from ipad
Can ping ipad from laptop
can ping laptop from ipad.
Apple tv never sees any other device.
Any ideas?Fascinating just reading about your setup. I have a WRT350N and have noticed that it will drop its speed, sometimes down to 1Mbps. It seems to do so at about the same time every day, but usually comes back to speed in about 5 minutes. In my experience, the Apple TV will disconnect if the speed falls this low. Try monitoring the Linksys with Netstumbler, Vistumbler, or just in the Windows Network utility.
Check the "lease obtained" and "lease expired" times for your router to see if that is when the network fails. I've just finished reading an angry thread over at the Linksys forum about the WRT330N where someone mentioned that the router wasn't renewing its lease.
"I cannot set it run off automatic DHCP from the WRT330N, the router will not assign it an IP every time the lease expires, causing me to have to manually set an IP on the Print server. That's annoying. Having the router drop IP's to individual machines after 12-48 hours...very annoying."
http://forums.linksys.com/linksys/board/message?board.id=Wireless_Routers&thread .id=67412
If that is the problem, then I would consider setting up a Static IP address for your Apple TV. You can do that through the user interface -> Settings -> Network -> Configure ... (Quite intuitive as you only have change IP address and the subsequent details remain the same.)
My router assigns IP Addresses in the ranges of 192.168.1.100 ->149. The idea here is to choose an address outside of that range but is not greater than 192.168.1.253 (and should not end in the number 1). You shouldn't have to change the linksys router as long as 50 clients are assigned in that range. You'll have to figure that out by accessing your router webpage at browser address 192.168.1.1 -> the default password is "admin" (without the quotes).
Good luck. -
Access points no longer join WLC
I have a 2106 v6.0.199 controller that was working fine with 3 access points. The Access points lost power and now will not rejoin to the controller. DHCP option 43 is in place. Any ideas on what is causing them to not join.
*Jan 17 08:24:43.726: 1c:df:0f:5a:4e:00 Discovery Request from 10.22.4.102:62025
*Jan 17 08:24:43.726: 1c:df:0f:5a:4e:00 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 6, joined Aps =0
*Jan 17 08:24:43.727: 1c:df:0f:5a:4e:00 Discovery Response sent to 10.22.4.102:62025
*Jan 17 08:24:43.727: 1c:df:0f:5a:4e:00 Discovery Request from 10.22.4.102:62025
*Jan 17 08:24:43.727: 1c:df:0f:5a:4e:00 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 6, joined Aps =0
*Jan 17 08:24:43.727: 1c:df:0f:5a:4e:00 Discovery Response sent to 10.22.4.102:62025
*Jan 17 08:24:43.727: 1c:df:0f:5a:4e:00 Received LWAPP DISCOVERY REQUEST to 00:25:84:f2:2a:20 on port '1'
*Jan 17 08:24:43.727: 1c:df:0f:5a:4e:00 Discarding discovery request in LWAPP from AP supporting CAPWAP
*Jan 17 08:24:58.237: 1c:df:0f:5a:43:50 Discovery Request from 10.22.4.103:62008
*Jan 17 08:24:58.237: 1c:df:0f:5a:43:50 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 6, joined Aps =0
*Jan 17 08:24:58.237: 1c:df:0f:5a:43:50 Discovery Response sent to 10.22.4.103:62008
*Jan 17 08:24:58.238: 1c:df:0f:5a:43:50 Discovery Request from 10.22.4.103:62008
*Jan 17 08:24:58.238: 1c:df:0f:5a:43:50 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 6, joined Aps =0
*Jan 17 08:24:58.238: 1c:df:0f:5a:43:50 Discovery Response sent to 10.22.4.103:62008
*Jan 17 08:24:58.238: 1c:df:0f:5a:43:50 Received LWAPP DISCOVERY REQUEST to 00:25:84:f2:2a:20 on port '1'
*Jan 17 08:24:58.238: 1c:df:0f:5a:43:50 Discarding discovery request in LWAPP from AP supporting CAPWAP
*Jan 17 08:25:06.815: ec:c8:82:a4:e7:d0 Discovery Request from 10.22.4.101:60911
*Jan 17 08:25:06.815: ec:c8:82:a4:e7:d0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 6, joined Aps =0
*Jan 17 08:25:06.815: ec:c8:82:a4:e7:d0 Discovery Response sent to 10.22.4.101:60911
*Jan 17 08:25:06.815: ec:c8:82:a4:e7:d0 Discovery Request from 10.22.4.101:60911
*Jan 17 08:25:06.815: ec:c8:82:a4:e7:d0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 6, joined Aps =0
*Jan 17 08:25:06.815: ec:c8:82:a4:e7:d0 Discovery Response sent to 10.22.4.101:60911
*Jan 17 08:25:28.719: sshpmLscTask: LSC Task received a message 4
*Jan 17 08:25:53.772: 1c:df:0f:5a:4e:00 Discovery Request from 10.22.4.102:62024
*Jan 17 08:25:53.772: 1c:df:0f:5a:4e:00 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 6, joined Aps =0
*Jan 17 08:25:53.772: 1c:df:0f:5a:4e:00 Discovery Response sent to 10.22.4.102:62024
*Jan 17 08:25:53.773: 1c:df:0f:5a:4e:00 Discovery Request from 10.22.4.102:62024
*Jan 17 08:25:53.773: 1c:df:0f:5a:4e:00 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 6, joined Aps =0
*Jan 17 08:25:53.773: 1c:df:0f:5a:4e:00 Discovery Response sent to 10.22.4.102:62024
*Jan 17 08:25:53.773: 1c:df:0f:5a:4e:00 Received LWAPP DISCOVERY REQUEST to 00:25:84:f2:2a:20 on port '1'Hi glwendt,
Could you tell me how did resolved the problem with the AP certificate?
I am with the same problem here.
Thanks! -
Access Points at branch and WLC located at Head Quarters
Guys,
Please excuse these entry-level questions, but we are just starting here with Cisco wireless technologies.... Can we deploy, let's say 8 3600 APs in one branch and have the WLC deployed at another branch? Could this be possible?
thank you in advanceGuys, thank you very much for the input so far.
You are always not one, but many steps ahead from a novice
George Stefanick, yes, we have IPSec site-to-site tunnels with all the branches from the main site. Is via the vpn tunnels where FlexConnect limitations come to play? What exactly are the limitations of FlexConnect that I need to be aware of??/
As you can see, we have many branches all over the states and also overseas. The initial thought was only to deploy APs where we have warehouses (we really have over 20 branches - and growing - but only 5 of them have warehouses...) So, as I look deeper into cisco WiFi technologies, I can really see all these good features that we can certainly use. So with these features, I think it might make more sense, like rasikanayanajith advised, to really keep the WLC at the main site and deploy the APs at the warehouse with the FlexConnect feature.
This way, all the executives, as they travel to all the 5 warehouses, will only need to be concerned with one single set of credentials (their AD credentials), is this correct???? as I assume we can setup Radius Authentication for the clients to login via the WiFi.
please advise and thank you again -
Hi All,
I'm trying to put together a Guest WLAN setup and want to know the best approach.
If I use ISE for Guest portal/access control do I still have the standard setup of Anchor WLCs in DMZ for the guest WLANs?
Or does the ISE tell the internal WLC's to place the allowed guest users onto a guest VLAN accessible to the internal WLCs?
Do I lose anything with ISE compared to the old WCS/WLC guest portal methods?
Any thoughts would be appreciated.
Thanks,
BrendanBrendan,
From my experience you still should use a dmz guest anchor controller. The only difference is the ports you will need to open on the FW between the guest anchor and ISE. Now you can still do this without a guest anchor if there isn't an existing one or one not planned for.
Thanks,
Scott Fella
Sent from my iPhone -
Guest VLAN - FlexConnnect Central Switching vs Anchor WLC
I have a general question about securing the guest WLAN in FlexConnect deployment -
Option 1: In the Centralized WLC deployment scenario, the guest VLAN is centrally switched to the datacenter WLC and the guest VLAN is trunked from that WLC to the firewall DMZ through a switch
Option 2: In the Centralized WLC deployment scenario, the guest VLAN is centrally switched to the datacenter WLC but tunneled to an anchor WLC in DMZ
Option 3: In the Centralized WLC deployment scenario, the guest VLAN is centrally switched to the datacenter WLC and an ACL is applied to the Guest interface/VLAN in the WLC itself
What would be the best option in the FlexConnect Centralized WLC deployment to restriect guest traffic from accessing corporate network? What are the advantages and disadvantages of those three options?
I would highly appraciate your input on this topic.
Thank you.Yes, you're right.
Once anchor/tunnel goes down, all the L3 services will be initiated for guest wlan from the Foreign until the Anchor comes up.
On Anchor down situation - Need to configure the foreign WLC's guest wlan mapped to dummy interface, this way guest clients will have no network access.
If multiple Anchors are mapped to the datacenter's foreign on the guest wlan then the guest users will tunnel the traffic to available anchor, by default it'll round robin among anchors. -
3502 access point will not connect to 4400 Series WLAN controller
I recently upgraded our controllers to the latest version 7 software, as I read this was one of the requirements to get them to connect. But I am not having any luck getting into a controller. Normally I plug them in to the network, they pop into the controller listed as something like AP5057.a844.xxxx and then I can finish configuring them, but a static IP on them, etc...
This is the first of this model AP I have tried to deploy, so I am wondering what is different with these. or what I might be missing in the default config in the WLAN controllers.
Niether of which are set to "Master" either.
Thanks in advance, TandristHi,
The 3500 as you mention are supported on code 7.0
To get the access point to join the WLC we have different options.
If the access points will be on the same subnet as the WLC then you just need to get the APs to get a valid IP address from the DHCP server and once they have an IP address they will join the WLC because they are on the same subnet as the WLC.
If the access points are on a different subnet then the WLC you will need to have a DHCP server configured to give the unit an IP address and use option 43 or DNS so that the APs can send the join request to the correct WLC on a different subnet.
Or if not configure the AP via the console port with the static IP address and WLC IP address.
Also make sure that you have the correct country code enable on the WLC, and that the APs you purchased are the ones to work in this country, because if not the AP will not join the WLC.
http://www.cisco.com/en/US/prod/collateral/wireless/ps5678/ps10981/data_sheet_c78-594630.html -
Cisco Outdoor Controller Based Access Point
Hi,
I am looking for Cisco Outdoor Controller Based access point model. The WLC is Cisco 2500 Series.
I have checked couple of outdoor models but all are mesh access point. I am looking for normal controller based outdoor access point ( just like controller based indoor access point models )
Thanks.adding to Leo...
Cisco Aironet 1300 Series
http://www.cisco.com/en/US/products/ps5861/index.html
Cisco Aironet 1550 Series
http://www.cisco.com/en/US/products/ps11451/index.html
Cisco Aironet 1520 Series
http://www.cisco.com/en/US/products/ps8368/index.html
these all are Cisco OUTdoor APs.
Now u can choose as per ur req.
Regards
Dont forget to rate helpful posts -
Access Points do not show in CDP neighbor
Hi All,
Last night I was performing mainteance on access points throughout the network. I was converting them from Local to H-REAP to allow for vlan support. The maintenance went well however afterwards I've noticed access points are not showing up in CDP neighbor and with a "show power inline" the access points shows as a IEEE PD. This is causing some weird issues where a client can connect but then will lose it's DHCP address. The problem happened on 9 of the 12 floors that I did this on and there is no configuration differences and bouncing the access points did not resolve the issue. The access points do show a blue light.
Has anyone ever experienced this before? If so what did you do to fix it?
I have a mix of 1131 and 1142N access points on a 4402 WLC running version 6.0.188.0.
Thank you,
Chris PrattThe maintenance went well however afterwards I've noticed access points are not showing up in CDP neighbor and with a "show power inline" the access points shows as a IEEE PD.
I see all the time.
"sh cdp neigh" shows nothing and "sh power inline" shows the port connected to the WAP as "IEEE". This is mostly caused by faulty cabling. If you have the right Cisco switch, you can test the cable using the in-built TDR feature.
Here's how you do it:
1. Command: test cable tdr interface
2. Wait for about 5 to 7 seconds;
3. Command: sh cable tdr interface
4. Please post the complete output. -
What is best practise to configure 10 access points? working on project in big warehouse.
Sent from Cisco Technical Support Android AppHi,
You can use any option you like to get the access points to join the WLC.
If the access points are on the same subnet as the WLC then you can stay with basic layer 2 discovery method that what the AP will do is once it gets an IP address if will send a broadcast request on the same subnet to join a WLC and since there is a WLC on the same subnet it will reply back and the AP will be able to join the WLC.
If the access points are on a different subnet then the WLC you need to use a layer 3 discovery method so that the AP can learn the IP address of the WLC that is on a different subnet and send a unicast join request to the specifc IP address.
The options would be option 43 or DNS lockup.
DNS option.
http://www.cisco.com/en/US/products/ps6366/products_tech_note09186a00809d5097.shtml
Option 43.
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a00808714fe.shtml -
Access points not registering with WLC
Hi all,
I have a 5508 WLC in LAG mode and have 14 1231G WAPs connected to it already. However I still have to migrate 9 more WAPs from my old 4404 controller to the new 5508 controller. I cannot get remaining 9 WAPs to register with new WLC. I found following debug message from the WLC. My WLC license is valid for 50 APs. Have any of you guys seen this? What am I doing wrong here? Any lead is much appriciated.
I have LAG setup with 2 ports out of 8 ports. Don't understand why it's giving error of not having enough capacity.
Any advice is much appriciated. Thanks in advance.
*spamApTask4: May 21 18:58:29.468: 00:23:04:c9:72:00 Echo Timer Expiry: Did not receive heartbeat reply from AP 00:23:04:c9:72:00 (10:4:12:26/36602)
*spamApTask0: May 21 18:58:50.588: 00:13:60:7e:28:30 Join Priority Processing status = 0, Incoming Ap's Priority 0, MaxLrads = 50,joined Aps =14
*spamApTask0: May 21 18:58:50.588: 00:13:60:7e:28:30 Refusing Discovery Request from AP 00:13:60:7e:28:30 - no AP manager with available capacity
*spamApTask0: May 21 18:58:50.588: 00:13:60:7e:28:30 Join Priority Processing status = 0, Incoming Ap's Priority 0, MaxLrads = 50,joined Aps =14
*spamApTask0: May 21 18:58:50.588: 00:13:60:7e:28:30 Refusing Discovery Request from AP 00:13:60:7e:28:30 - no AP manager with available capacity
*spamApTask0: May 21 18:59:00.589: Could not find BoardDataPayload
*spamApTask0: May 21 18:59:00.636:
*spamApTask0: May 21 18:59:05.593: Could not find BoardDataPayload
*spamApTask0: May 21 18:59:05.639:
*spamApTask0: May 21 18:59:53.564: 00:13:60:7e:28:30 Join Priority Processing status = 0, Incoming Ap's Priority 0, MaxLrads = 50,joined Aps =14
*spamApTask0: May 21 18:59:53.565: 00:13:60:7e:28:30 Refusing Discovery Request from AP 00:13:60:7e:28:30 - no AP manager with available capacity
*spamApTask0: May 21 18:59:53.565: 00:13:60:7e:28:30 Join Priority Processing status = 0, Incoming Ap's Priority 0, MaxLrads = 50,joined Aps =14
*spamApTask0: May 21 18:59:53.565: 00:13:60:7e:28:30 Refusing Discovery Request from AP 00:13:60:7e:28:30 - no AP manager with available capacityGuess the SSC got corrupted..
Run the command "debug pm pki enable" on the WLC, copy the SSC and paste it on the WLC and see if that helps.. here is the link to do the same!!
http://www.cisco.com/en/US/products/ps6366/products_configuration_example09186a00806a426c.shtml
Lemme know if this answered ur question and please dont forget to rate the usefull posts!!
Regards
Surendra
Maybe you are looking for
-
Problem in using client_image.read_image_file
Hi all I want to load a picture file into a forms item at Develeoper Forms 10g Rel.2 with the following procedure, but it doesnt work and i also get no error. PROCEDURE import_image IS vFileName VARCHAR2(512); BEGIN -- Transfer Picture from File Dire
-
I would like to encrypt/decrypt a binary file (not text based) in FLEX 3.4 (AIR). I went through the forum, but I did not found any samples on how to do this. Any idea or help is appreciated. Thanks in advanced.
-
Can I order a recovery disc for my HPG72 259WM
i cant create a recovery disc on my computer. the manager recovery said "the partition can be found" so i would like to know if can i order a recovery disc
-
Optimizing After Effects Performance/ Rendering Speed for large projects
Problem: My after effects is extremely slow and i want to use an external harddrive to increase the speed temporarily until i can afford to change the internal hard drive. i also have other video production software like Cinema 4D, Final Cut Pro, Pr
-
Refresh master block - best way?
hi, i want to refresh the master block every time a change is saved from the detail one (they have common items/fields). I want to do it by the fastest possible way cause it is gonna be on the web. Downloading all master rows again would not be an op