Access Point Secured Registration to WLC

Hello
Which option on WLC ensure that any AP registering to WLC should be first authenticated with a password and then register to a WLC
cheers
CP

Hell there ...
Take a peek at the below link.. I think this is what you are asking ?
Lightweight Access Point (LAP) Authorization in a Cisco Unified Wireless Network Configuration Example
http://www.cisco.com/en/US/customer/products/ps6366/products_configuration_example09186a00808c7234.shtml

Similar Messages

  • Limiting access points joining a specific WLC

    Hello Cisco Forum Team!
      I am currently installing a new WLC in a VLAN/IP segment that already has WLCs configured and access points registered. I do not want existing ap's on this VLAN to join this new WLC.  Which is the best way to limit ap's joining this new WLC?
    I am thinking of some sort of AP authorization list but by IP address instead of MAC address due to the high amount of ap's currently registred on the existing WLCs (approx. 300 ap's).
    Thanks in advanced for your support!

    AP authorization list would work but you have to use MAC address & cannot use IP address for that. Once you enable AP authorization you can add AP mac to the list like below using CLI.
    (5508-1) >config auth-list add mic <AP1 mac>
    (5508-1) >config auth-list add mic <AP2 mac>
    (5508-1) >config auth-list add mic <APn mac>
    HTH
    Rasika
    **** Pls rate all useful responses ****

  • Trying to get home shaing working on apple tv using Cisco Access points and a Cisco WLC 5508 with 7.2.110 code.  I can get devices working individually but they never see each other.  I can ping the apple tv from my laptop and ipad.

    Trying to get home sharing working on a corporate wireless network.  Cisco wireless.
    WLC5508 controller
    Cisco 3502 access points
    All apple devices on same WLAN - security WPA2-PSK
    ITunes account up to date
    All devices laterst software.
    Can ping apll tv from laptop
    can ping apple tv from ipad
    Can ping ipad from laptop
    can ping laptop from ipad.
    Apple tv never sees any other device.
    Any ideas?

    Fascinating just reading about your setup. I have a WRT350N and have noticed that it will drop its speed, sometimes down to 1Mbps. It seems to do so at about the same time every day, but usually comes back to speed in about 5 minutes. In my experience, the Apple TV will disconnect if the speed falls this low. Try monitoring the Linksys with Netstumbler, Vistumbler, or just in the Windows Network utility.
    Check the "lease obtained" and "lease expired" times for your router to see if that is when the network fails. I've just finished reading an angry thread over at the Linksys forum about the WRT330N where someone mentioned that the router wasn't renewing its lease.
    "I cannot set it run off automatic DHCP from the WRT330N, the router will not assign it an IP every time the lease expires, causing me to have to manually set an IP on the Print server. That's annoying. Having the router drop IP's to individual machines after 12-48 hours...very annoying."
    http://forums.linksys.com/linksys/board/message?board.id=Wireless_Routers&thread .id=67412
    If that is the problem, then I would consider setting up a Static IP address for your Apple TV. You can do that through the user interface -> Settings -> Network -> Configure ... (Quite intuitive as you only have change IP address and the subsequent details remain the same.)
    My router assigns IP Addresses in the ranges of 192.168.1.100 ->149. The idea here is to choose an address outside of that range but is not greater than 192.168.1.253 (and should not end in the number 1). You shouldn't have to change the linksys router as long as 50 clients are assigned in that range. You'll have to figure that out by accessing your router webpage at browser address 192.168.1.1 -> the default password is "admin" (without the quotes).
    Good luck.

  • WCS displays Access Point as disassociated but WLC shows as associated

    Hi all,
    I have a WCS ver 7.0.172, a 5508 WLAN Controller with ver 7.0.116.0. At this WLC 21 Access Points (AIR-LAP1131AG-E-K9 ) were associated. As well I have one CleanAir Access Point (AIR-CAP3502E-E-K9) is associated.
    And now ... my problem:
    every time the WCS got a critical error and reports that the AP is disassociated from Controller. But if I take a look to the WLC the AP is associated and works at local mode and have two clients associated.
    I cleared the alarm - a few minutes later the alarm will be reported again. Same result if I delete the alarm.
    Could anybody give support for that issue.
    Thanks and regards
    Holger

    Hi Holgerseiler,
    Have you got any information/solution on this issue?
    I also have same kind of issue. I have a WCS with version 7.0.172.0, and around 25 WLCs (version7.0.116.0, in which i checked) and totally around 1000 APs are assiociated in wireless network.
    Some error messages are coming on my WCS device like
    "AP disassociated from Controller [ip]"
    Here AP name and WLC ip address will change randomly, but there is no impact on my network.
    Thanks in advance
    Sangeeth BS

  • Public Access Point Security

    Hi,
    Is it possible to extend the concept of layer 2 ethernet vlans to wifi networks, with a system that allocates a VLAN per user (allowing 4096 users) on wifi connection?
    I was thinking that this could help prevent Man In The Middle attacks as any new user joining a wifi network would be on their own separate subnet isolated from every other user.
    If this is achieved at the SSID level by assigning each one to a VLAN, is it possible to have this happen automatically?
    Is this how public access points work already and if so how is a MITM attack launched?
    Thanks.

    yes and no.
    the WLC will only take 512 interfaces so you could do that many /32 subnets if you really wanted to.  But you wouldn't be able to max out the 4096
    But, what you can do, is enable Peer to Peer blocking, which disallows clients to talk to each other on the same WLAN
    HTH,
    Steve
    Please remember to rate useful posts, and mark questions as answered

  • Access points connect to wrong WLC

    Hello everybody,
    I have a problem with some access point.
    We have two WLC's one AIR-CT5508-K9 and one AIR-WLC4404-100-K9.
    now i have 6 access points that don't register anymore to the right controller.
    in high availability i have set the right name of primary controller and also the correct ip address, but somehow they keep registering to the other controller.
    Does someone know how i can fix this problem.
    info:
    AIR-CT5508:SEDA-PM_Line_1
    WLC4404: SEDA-PM_Office_1
    6 accesspoints are connected to SEDA-PM_Line_1 but they should be connected to SEDA-PM_Office_1
    settings in AP are correct in my opinion

    here is the information,
    (Cisco Controller) >show sysinfo
    Manufacturer's Name.............................. Cisco Systems Inc.
    Product Name..................................... Cisco Controller
    Product Version.................................. 7.0.116.0
    RTOS Version..................................... 7.0.116.0
    Bootloader Version............................... 3.2.195.10
    Emergency Image Version.......................... N/A
    Build Type....................................... DATA + WPS
    System Name...................................... SEDA-PM_Office_1
    System Location.................................. Mao, Brazil
    System Contact................................... Network_Admin
    System ObjectID.................................. 1.3.6.1.4.1.14179.1.1.4.3
    IP Address....................................... 105.103.112.5
    System Up Time................................... 8 days 15 hrs 9 mins 55 secs
    System Timezone Location.........................
    Configured Country............................... US  - United States
    Operating Environment............................ Commercial (0 to 40 C)
    Internal Temp Alarm Limits....................... 0 to 65 C
    Internal Temperature............................. +38 C
    --More-- or (q)uit
    State of 802.11b Network......................... Enabled
    State of 802.11a Network......................... Disabled
    Number of WLANs.................................. 13
    Number of Active Clients......................... 132
    Burned-in MAC Address............................ 00:22:55:91:2B:C0
    Crypto Accelerator 1............................. Absent
    Crypto Accelerator 2............................. Absent
    Power Supply 1................................... Absent
    Power Supply 2................................... Present, OK
    Maximum number of APs supported.................. 100
    (Cisco Controller) >show time
    Time............................................. Thu Jan  9 07:58:29 2014
    Timezone delta................................... -4:0
    Timezone location................................
    NTP Servers
        NTP Polling Interval.........................     86400
         Index     NTP Key Index     NTP Server      NTP Msg Auth Status
           1              0        211.189.10.2       AUTH DISABLED
    AP information
    Warehouse_AP-3#sh version
    Cisco IOS Software, C1240 Software (C1240-K9W8-M), Version 12.4(23c)JA2, RELEASE SOFTWARE (fc3)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2011 by Cisco Systems, Inc.
    Compiled Wed 13-Apr-11 12:58 by prod_rel_team
    ROM: Bootstrap program is C1240 boot loader
    BOOTLDR: C1240 Boot Loader (C1240-BOOT-M) Version 12.4(13d)JA, RELEASE SOFTWARE (fc2)
    Warehouse_AP-3 uptime is 18 hours, 16 minutes
    System returned to ROM by power-on
    System image file is "flash:/c1240-k9w8-mx.124-23c.JA2/c1240-k9w8-mx.124-23c.JA2"
    This product contains cryptographic features and is subject to United
    States and local country laws governing import, export, transfer and
    use. Delivery of Cisco cryptographic products does not imply
    third-party authority to import, export, distribute or use encryption.
    Importers, exporters, distributors and users are responsible for
    compliance with U.S. and local country laws. By using this product you
    agree to comply with applicable laws and regulations. If you are unable
    to comply with U.S. and local laws, return this product immediately.
    A summary of U.S. laws governing Cisco cryptographic products may be found at:
    http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
    If you require further assistance please contact us by sending email to
    [email protected].
    cisco AIR-LAP1242AG-A-K9   (PowerPCElvis) processor (revision A0) with 27638K/5120K bytes of memory.
    Processor board ID FTX1233B943
    PowerPCElvis CPU at 262Mhz, revision number 0x0950
    Last reset from power-on
    LWAPP image version 7.0.116.0
    1 FastEthernet interface
    2 802.11 Radio(s)
    32K bytes of flash-simulated non-volatile configuration memory.
    Base ethernet MAC Address: 00:1D:70:96:64:A0
    Part Number                          : 73-9925-07
    PCA Assembly Number                  : 800-26579-06
    PCA Revision Number                  : A0
    PCB Serial Number                    : FOC12320AKT
    Top Assembly Part Number             : 800-29151-03
    Top Assembly Serial Number           : FTX1233B943
    Top Revision Number                  : A0
    Product/Model Number                 : AIR-LAP1242AG-A-K9 
    Configuration register is 0xF
    Warehouse_AP-3#sh ip interface brief
    Interface                  IP-Address      OK? Method Status                Protocol
    Dot11Radio0                unassigned      NO  unset  up                    up     
    Dot11Radio1                unassigned      NO  unset  administratively down down   
    FastEthernet0              105.103.27.19   YES other  up                    up 
    Warehouse_AP-3#sh inventory
    NAME: "AP1240", DESCR: "Cisco Aironet 1240 Series (IEEE 802.11a/g) Access Point"
    PID: AIR-LAP1242AG-A-K9, VID: V03, SN: FTX1233B943
    there are 7 AP's that not register to the right controller some are different models:
    Warehouse_AP-1 - AIR-LAP1242G-A-K9
    Warehouse_AP-3 - AIR-LAP1242AG-A-K9
    Warehouse_AP-5 - AIR-LAP1242G-A-K9
    Warehouse_AP-6 - AIR-LAP1242G-A-K9
    Warehouse_AP-7 - AIR-CAP3502I-T-K9
    Warehouse_AP-9 - AIR-LAP1242AG-A-K9
    Warehouse_AP-10 - AIR-LAP1242G-A-K9
    Thank you for your help!!

  • Access-point 1131G registration issues on Wireless controller over Layer3 transport mode.

    There are set of 1131G access points which belong to different segment  than management couldn’t be registered on Wireless Controller (Catalyst 6509 WISM). However access points allocated in same range of management network is easily registering on controller. I have created AP-Manager interface which allowing Dynamic AP-Management. Once I’m creating dynamic interface on Controller which pointed to Layer3 interface of APs vlan, the controller starts deducting those access points as not-joined APs  and displaying following messages. Please suggest.
    Lwapp discovery request rejected.
    Layer 3 discovery request not received on management VLAN.

    Hi Pankaj,
    Here is the bug ID..
    http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCti54658
    Please create a seperate Dynamic interafce and then see what happens as per the bug work around..
    lemme know if this answered your question..
    Regards
    Surendra
    ====
    Please dont forget to rate the post which answered your question or was usefull

  • Access points no longer join WLC

    I have a 2106 v6.0.199 controller that was working fine with 3 access points. The Access points lost power and now will not rejoin to the controller. DHCP option 43 is in place. Any ideas on what is causing them to not join.
    *Jan 17 08:24:43.726: 1c:df:0f:5a:4e:00 Discovery Request from 10.22.4.102:62025
    *Jan 17 08:24:43.726: 1c:df:0f:5a:4e:00 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 6, joined Aps =0
    *Jan 17 08:24:43.727: 1c:df:0f:5a:4e:00 Discovery Response sent to 10.22.4.102:62025
    *Jan 17 08:24:43.727: 1c:df:0f:5a:4e:00 Discovery Request from 10.22.4.102:62025
    *Jan 17 08:24:43.727: 1c:df:0f:5a:4e:00 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 6, joined Aps =0
    *Jan 17 08:24:43.727: 1c:df:0f:5a:4e:00 Discovery Response sent to 10.22.4.102:62025
    *Jan 17 08:24:43.727: 1c:df:0f:5a:4e:00 Received LWAPP DISCOVERY REQUEST to 00:25:84:f2:2a:20 on port '1'
    *Jan 17 08:24:43.727: 1c:df:0f:5a:4e:00 Discarding discovery request in LWAPP from AP supporting CAPWAP
    *Jan 17 08:24:58.237: 1c:df:0f:5a:43:50 Discovery Request from 10.22.4.103:62008
    *Jan 17 08:24:58.237: 1c:df:0f:5a:43:50 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 6, joined Aps =0
    *Jan 17 08:24:58.237: 1c:df:0f:5a:43:50 Discovery Response sent to 10.22.4.103:62008
    *Jan 17 08:24:58.238: 1c:df:0f:5a:43:50 Discovery Request from 10.22.4.103:62008
    *Jan 17 08:24:58.238: 1c:df:0f:5a:43:50 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 6, joined Aps =0
    *Jan 17 08:24:58.238: 1c:df:0f:5a:43:50 Discovery Response sent to 10.22.4.103:62008
    *Jan 17 08:24:58.238: 1c:df:0f:5a:43:50 Received LWAPP DISCOVERY REQUEST to 00:25:84:f2:2a:20 on port '1'
    *Jan 17 08:24:58.238: 1c:df:0f:5a:43:50 Discarding discovery request in LWAPP from AP supporting CAPWAP
    *Jan 17 08:25:06.815: ec:c8:82:a4:e7:d0 Discovery Request from 10.22.4.101:60911
    *Jan 17 08:25:06.815: ec:c8:82:a4:e7:d0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 6, joined Aps =0
    *Jan 17 08:25:06.815: ec:c8:82:a4:e7:d0 Discovery Response sent to 10.22.4.101:60911
    *Jan 17 08:25:06.815: ec:c8:82:a4:e7:d0 Discovery Request from 10.22.4.101:60911
    *Jan 17 08:25:06.815: ec:c8:82:a4:e7:d0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 6, joined Aps =0
    *Jan 17 08:25:06.815: ec:c8:82:a4:e7:d0 Discovery Response sent to 10.22.4.101:60911
    *Jan 17 08:25:28.719: sshpmLscTask: LSC Task received a message 4
    *Jan 17 08:25:53.772: 1c:df:0f:5a:4e:00 Discovery Request from 10.22.4.102:62024
    *Jan 17 08:25:53.772: 1c:df:0f:5a:4e:00 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 6, joined Aps =0
    *Jan 17 08:25:53.772: 1c:df:0f:5a:4e:00 Discovery Response sent to 10.22.4.102:62024
    *Jan 17 08:25:53.773: 1c:df:0f:5a:4e:00 Discovery Request from 10.22.4.102:62024
    *Jan 17 08:25:53.773: 1c:df:0f:5a:4e:00 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 6, joined Aps =0
    *Jan 17 08:25:53.773: 1c:df:0f:5a:4e:00 Discovery Response sent to 10.22.4.102:62024
    *Jan 17 08:25:53.773: 1c:df:0f:5a:4e:00 Received LWAPP DISCOVERY REQUEST to 00:25:84:f2:2a:20 on port '1'

    Hi glwendt,
    Could you tell me how did resolved the problem with the AP certificate?
    I am with the same problem here.
    Thanks!

  • Access point register on anchor wlc in DMZ

    Hello,
    I have an environment in which two WLC 4400 are connected to an anchor WLC 4400 in DMZ, This WLC in DMZ pass the Guest Wlan to other two WLC and terminate tunnel CAPWAP. The Ap in the remote sites, that are configure to register to WLCs in the remote sites, usually are registered on the two WLCs but sometimes they register to WLC in DMZ, how is possible if between WLC in DMZ and other WLC there is a firewall that block all the traffic except CAPWAP traffic? 
    If I reboot the APs they register on the two correct WLCs in remote sites.
    Thanks

    AP also uses CAPWAP.  you should only allow capwap connection from internal controllers only on the fw.

  • Access points not registering with WLC

    Hi all,
    I have a 5508 WLC in LAG mode and have 14 1231G WAPs connected to it already. However I still have to migrate 9 more WAPs from my old 4404 controller to the new 5508 controller. I cannot get remaining 9 WAPs to register with new WLC. I found following debug message from the WLC. My WLC license is valid for 50 APs. Have any of you guys seen this? What am I doing wrong here? Any lead is much appriciated.
    I have LAG setup with 2 ports out of 8 ports. Don't understand why it's giving error of not having enough capacity.
    Any advice is much appriciated. Thanks in advance.
    *spamApTask4: May 21 18:58:29.468: 00:23:04:c9:72:00 Echo Timer Expiry: Did not receive heartbeat reply from AP 00:23:04:c9:72:00 (10:4:12:26/36602)
    *spamApTask0: May 21 18:58:50.588: 00:13:60:7e:28:30 Join Priority Processing status = 0, Incoming Ap's Priority 0, MaxLrads = 50,joined Aps =14
    *spamApTask0: May 21 18:58:50.588: 00:13:60:7e:28:30 Refusing Discovery Request from AP 00:13:60:7e:28:30 - no AP manager with available capacity
    *spamApTask0: May 21 18:58:50.588: 00:13:60:7e:28:30 Join Priority Processing status = 0, Incoming Ap's Priority 0, MaxLrads = 50,joined Aps =14
    *spamApTask0: May 21 18:58:50.588: 00:13:60:7e:28:30 Refusing Discovery Request from AP 00:13:60:7e:28:30 - no AP manager with available capacity
    *spamApTask0: May 21 18:59:00.589: Could not find BoardDataPayload
    *spamApTask0: May 21 18:59:00.636:
    *spamApTask0: May 21 18:59:05.593: Could not find BoardDataPayload
    *spamApTask0: May 21 18:59:05.639:
    *spamApTask0: May 21 18:59:53.564: 00:13:60:7e:28:30 Join Priority Processing status = 0, Incoming Ap's Priority 0, MaxLrads = 50,joined Aps =14
    *spamApTask0: May 21 18:59:53.565: 00:13:60:7e:28:30 Refusing Discovery Request from AP 00:13:60:7e:28:30 - no AP manager with available capacity
    *spamApTask0: May 21 18:59:53.565: 00:13:60:7e:28:30 Join Priority Processing status = 0, Incoming Ap's Priority 0, MaxLrads = 50,joined Aps =14
    *spamApTask0: May 21 18:59:53.565: 00:13:60:7e:28:30 Refusing Discovery Request from AP 00:13:60:7e:28:30 - no AP manager with available capacity

    Guess the SSC got corrupted..
    Run the command "debug pm pki enable" on the WLC, copy the SSC and paste it on the WLC and see if that helps.. here is the link to do the same!!
    http://www.cisco.com/en/US/products/ps6366/products_configuration_example09186a00806a426c.shtml
    Lemme know if this answered ur question and please dont forget to rate the usefull posts!!
    Regards
    Surendra

  • Access Points at branch and WLC located at Head Quarters

    Guys,
    Please excuse these entry-level questions, but we are just starting here with Cisco wireless technologies.... Can we deploy, let's say 8 3600 APs in one branch and have the WLC deployed at another branch? Could this be possible?
    thank you in advance                  

    Guys, thank you very much for the input so far.
    You are always not one, but many steps ahead from a novice
    George Stefanick, yes, we have IPSec site-to-site tunnels with all the branches from the main site. Is via the vpn tunnels where FlexConnect limitations come to play?  What exactly are the limitations of FlexConnect that I need to be aware of??/
    As you can see, we have many branches all over the states and also overseas. The initial thought was only to deploy APs where we have warehouses (we really have over 20 branches - and growing - but only 5 of them have warehouses...) So, as I look deeper into cisco WiFi technologies, I can really see all these good features that we can certainly use. So with these features, I think it might make more sense, like rasikanayanajith advised, to really keep the WLC at the main site and deploy the APs at the warehouse with the FlexConnect feature.
    This way, all the executives, as they travel to all the 5 warehouses, will only need to be concerned with one single set of credentials (their AD credentials), is this correct????  as I assume we can setup Radius Authentication for the clients to login via the WiFi.
    please advise and thank you again

  • L3 connections between Access points and WLC

    hi,
    we have a customer asking us to configure wireless system as per attached drawing.
     WLC is in Data Center which is connected to Data Center Switch ( Cisco 3850), then this DC-Switch is connected to DC-Core ( Cisco Nexus-7K).
    this Nexus-7K is connected to many campus Networks. in all campuses there is Cisco 4507 Campus Core which is connected to Nexus-7K.
    then from Campus core many distribution switches are connected.
    all Vlans for data and wifi is created in Distribution Switches. Distribution Switches are VTP Servers and many access switches with connected APs are connected back to this Distribution Switch.
    All Access Points are registered at WLC in Data Center, but wifi clients are not getting ip address from DHCP Server, as well as even if we configured static ip address at wifi clients they are not able to communicate correctly.
    please correct me if there is a mistake in this design , or we have a solution to solve this problem please let me know.
    attached topology diagram 
    thanks,
    anvar

    Hey Anvar,
    Too much details about network, to make it simple:
    1- APs and WLC can be in separate VLANs (Not a problem)
    2- As APs have joined, these two VLANs look fine for me
    If your clients can't communicate probably with static IP address
    1- From the WLC, ping default gateway for that VLAN
    2- If the WLC can reach the gateway, its wired VLAN issue that you need to investigate in the path (maybe using wired device in the same VLAN as the clients in the switch where the APs are connected)
    Now, about why the clients are not taking IP:
    1- What is your DHCP, where its located? Is it the same one for all clients?
    2- Do you have local APs or FlexConnect ?
    3- When you run the debugs for DHCP where the process breaks?
    Cheers,
    Nour

  • 3502 access point will not connect to 4400 Series WLAN controller

    I recently upgraded our controllers to the latest version 7 software, as I read this was one of the requirements to get them to connect.  But I am not having any luck getting into a controller.  Normally I plug them in to the network, they pop into the controller listed as something like AP5057.a844.xxxx and then I can finish configuring them, but a static IP on them, etc...
    This is the first of this model AP I have tried to deploy, so I am wondering what is different with these. or what I might be missing in the default config in the WLAN controllers.
    Niether of which are set to "Master" either.
    Thanks in advance, Tandrist

    Hi,
    The 3500 as you mention are supported on code 7.0
    To get the access point to join the WLC we have different options.
    If the access points will be on the same subnet as the WLC then you just need to get the APs to get a valid IP address from the DHCP server and once they have an IP address they will join the WLC because they are on the same subnet as the WLC.
    If the access points are on a different subnet then the WLC you will need to have a DHCP server configured to give the unit an IP address and use option 43 or DNS so that the APs can send the join request to the correct WLC on a different subnet.
    Or if not configure the AP via the console port with the static IP address and WLC IP address.
    Also make sure that you have the correct country code enable on the WLC, and that the APs you purchased are the ones to work in this country, because if not the AP will not join the WLC.
    http://www.cisco.com/en/US/prod/collateral/wireless/ps5678/ps10981/data_sheet_c78-594630.html

  • Cisco Outdoor Controller Based Access Point

    Hi,
    I am looking for Cisco Outdoor Controller Based access point model. The WLC is Cisco 2500 Series.
    I have checked couple of outdoor models but all are mesh access point. I am looking for  normal controller based outdoor access point ( just like controller based indoor access point models )
    Thanks.

    adding to Leo...
    Cisco Aironet 1300 Series
    http://www.cisco.com/en/US/products/ps5861/index.html
    Cisco Aironet 1550 Series
    http://www.cisco.com/en/US/products/ps11451/index.html
    Cisco Aironet 1520 Series
    http://www.cisco.com/en/US/products/ps8368/index.html
    these all are Cisco OUTdoor APs.
    Now u can choose as per ur req.
    Regards
    Dont forget to rate helpful posts

  • Access Points do not show in CDP neighbor

    Hi All,
    Last night I was performing mainteance on access points throughout the network. I was converting them from Local to H-REAP to allow for vlan support. The maintenance went well however afterwards I've noticed access points are not showing up in CDP neighbor and with a "show power inline" the access points shows as a IEEE PD. This is causing some weird issues where a client can connect but then will lose it's DHCP address. The problem happened on 9 of the 12 floors that I did this on and there is no configuration differences and bouncing the access points did not resolve the issue. The access points do show a blue light.
    Has anyone ever experienced this before? If so what did you do to fix it?
    I have a mix of 1131 and 1142N access points on a 4402 WLC running version 6.0.188.0.
    Thank you,
    Chris Pratt

    The maintenance went well however afterwards I've noticed access points are not showing up in CDP neighbor and with a "show power inline" the access points shows as a IEEE PD.
    I see all the time.
    "sh cdp neigh" shows nothing and "sh power inline" shows the port connected to the WAP as "IEEE".  This is mostly caused by faulty cabling.  If you have the right Cisco switch, you can test the cable using the in-built TDR feature.
    Here's how you do it:
    1.  Command:  test cable tdr interface
    2.  Wait for about 5 to 7 seconds;
    3.  Command:  sh cable tdr interface
    4.  Please post the complete output. 

Maybe you are looking for