Access point setting

anybody who can help me to figure out what's wrong with my point, every time i try to configure my access point setting, a message will display "setting: memory full. close some appliocations and try again" pls help me

It is possible. If you give the phone at Nokia care they will also do a hard reset if required to do so. Therefore the risk is everywhere. If you have taken the full backup without problems there is small possibility of backup not getting restored if back-up and restore procedure is done correctly.
If my post has helped you please click the white star on the right

Similar Messages

N8 camera keeps asking for access point setting

Most times when I start the camera I get the popup saying "Network connection required. Define access point to connect?". I realise that it'll need a connection because I've enabled geo tagging, but shouldn't I only have to set this once? I've looked in the menus & can't find anything in there to set it permanently. It;'s most annoying & I reckon I'll be missing photo opportunities because of it.
Nokia N8 on Belle

go to connectivity settings and set to automatic instead of always ask . Or as aspergerguy suggested turn geo tagging on and off as required , but if you check your settings in connectivity it should work without asking good luck
If I have helped at all, a click on the White Star is always appreciated :
you can also help others by marking 'accept as solution'

Nokia E6 - Where is the Access point setting for Y...

I have my Nokia E6 configured for my Corporate Email, MfE and it works fine. In the settings for MfE, I see a setting for Access Point, where I choose Internet with Priority 1 as my Home WLAN and Priority 2 as my GPRS connection.
Then, I started to configure my private Yahoo mail, evertyhing is done, it works fine, but I do not see any settings for Access Point for the Yahoo mail..
Does this mean it picks up the settings from MfE???
Can any other NOkia E6 users or experts comment on this??

Hi Stuart,
To answer your question:
There is no shared secret for the ACS itself.
If the ACS is going to communicate with another device, you have to define a AAA client and define a shared secret.
ACS 4, used that shared secret to protect/secure the replication, in ACS 5, the replication secured with encryption and not shared secrets(hash).
Rate if useful

E63 Packet data Access point set to None? What hap...

What happens when Packet Data>Access point is set to None(blank)? I tried to tether with my phone and I was connected to the internet for a moment. Checked my ip and it turns out it's through my mobile phone companies subnet.
However via the Bluetooth DUN setup on my computer I specifid a computer and login information which it seemed to ignore? Can anyone explain this strange situation?
The phone I'm using is an E63 GSM phone.

that will work. You only need to change if you need to have always on (highly unlikley) or if you are using modem dial up and need to specify access point for that.
If you using Nokia One Touch access then you don't even need to define access point in this menu as that application will take care of it for you.
All other network aware applications will use access point settings as defined in settings menu.

How can I monitor the active access point + data c...

My privider (o2 Germany) requires me to use different access points (APN, proxy) on my phone (N80) depending on the type of browsing I want do do (WAP vs. "normal" access), and each of them has a "high cost trap" if I use the wrong one for the particular service.
Very annoying - up to the point that I consider not using the phone for online access at all because I'm so scared to run into uncontrollably high fees.
Anyways. I wonder if there is add-on software for my phone that helps me monitor my data connection, i.e.:
* show me the currently used access point at the top of the display (yes, I know I can go into some deep menus to look it up, but that's not very helpful or even easy to use)
* automatically disconnect when the conn is idle for a while (One of the data modes is time-based, meaning I do not want to have it open all the time by accident)
Currently, all I can see at the top of the display is that I have a data connection at all, but that does not give me enough information to know I'm in the right mode for what I'm doing.
Thomas

You can force a disconnect by pressing the red/hangup key for a couple of seconds when the phone is in the standby state.
And in menu > Tools > Settings > Connection > Packet data change the setting "Packet data conn." to "When needed" and leave the "Access point" setting there to "None".
When you or apps on your phone are not doing any data transfer, then regardless of whether it is a WAP or "full" Internet packet data connection, you should not cumulate any charges.
You can also move the Connection Manager app from the Tools submenu to the main menu, or even to the Active standby apps list (or the softkeys) for quicker access. No need to deep dive into menus for it then.
And for individual apps, you can usually set the default access point to whatever is best to use for that particular app. For the browsers ("Web" and "Services") you can also make them ask you to pick the access point every time you connect.

"No access point defined. Define one in Connection...

Hello, I have my Nokia N* for about two years now. I would always send MMS , but now I can't. This is the first time I am trying to send an MMS on Symbian Anna despite the fact of updating it months ago.
This is what happens:
1. I try to send a picture via SMS... which of course then becomes an MMS.
2. "No valid access point defined. Define one now?
3. I click YES
4."No access point defined. Define one in Connection settings." and the message dissapears. I then go to-->
5. TOOLS>SETTINGS>CONNECTIVITY>SETTINGS>NETWORK DESTINATIONS
6. There are 6 Internet Access Points and 4 WAP Access Points ( I added 5 Internet ones trying to figure this out and 3 wap ones trying to figure this out)
MY SETTINGS:
TOOLS>SETTINGS>CONNECTIVITY>SETTINGS
1. MOBILE DATA&colon; On
2. ALLOW MOBILE DATA USAGE: Worldwide
MESSAGES>SETTINGS
1. MMS creation Mode: FREE
2.ACCESS POINT IN USE (WITH A GREEN STAR): MMS send
3.MULTIMEDIA RETREIVAL: Always automatic
Please help me! =]

I called my provider "TIM" and they have no idea what I am talking about when I asked them to please send me a new Access Point setting for MMS. Why was this working perfectly before Anna>? and now not? My provider is the same.

E61i worldmate problems and default access point

I cannot get Worldmate to connect without error. Worldmate support tell me to ensure that the "device default access point" is correct. However, I have not been able to find a global default access point setting anywhere, including the help doc!
Once into worldmate, you can apparently change your access point, but the first time it looks for a global default. So I cant even get in!
My phone is working fine with GPRS and WLAN, as long as the application allows me to select the access point.
Perhaps this is a change between e61 and e61i?
Anybody have the same problem?
Chris

05-Aug-200708:01 PM
gtach43 wrote:
I have the same problem.
Both WorldMate and GolfPro2 workd when I first installed them. Now when I try to open them nothing happens.
I redownloaded WorldMate and re-installed, then both worked. After shutting down, neither work again.
How do you resolve this? Is it based on the access point?
Glenn
The exact same thing happens to me when I install other programs, like Nokia Maps or 3D pool. When I install them and reboot, both worldmate and the new installed program doesn't work. This doesn't happen with other programs that I've installed so far, like Gmail or google maps.

Setting up a netgear n300 as wireless bridge/access point with airport extremee

I just replaced my netgear wireless router with the airport to allow our many devices on the network without knocking each other off and also increase the speed. But would like to use the netgear as a wireless bridge or access point so that I can still connect my NTFS formatted hard drive to be shared on the network. Any suggestions would be appreciated. I can not seem to find my netgear router with 192.168.1.1 as that comes up with another device. I have tried doing this with a windows laptop in another room but can not seem to make it work. I am now hooked up directly to the airport thinking i need to do it that way and still no luck. Please help.

As long as you intend to do this over ethernet it will work.. you cannot easily wireless repeat or bridge to an apple router.. you would need specific hardware to do it.
What is the exact model of netgear you have?
The setup method depends on the functionality of the router.. but lets assume it does not have a bridge or WAP mode.
You use WAN bypass.
1. Setup the Netgear with IP address in the correct IP range for the rest of the network.. it is hard to talk generalities so lets say the apple is main router and your network is now 10.0.1.x .. then set the Netgear to 10.0.1.250 (apple uses IP 2-200 by default) you can use any value you like outside the DHCP range. Up to the limit which is 254 as long as you keep track of all static IP devices. Apply this setting and power cycle the router.. and you might need to power cycle the computer as well to pick up the new IP.
2. Turn off the DHCP server in the Netgear. You may lose connection to the netgear now.. do not worry about it.. (this can be combined with one.. if you firstly turn off dhcp before you change the IP.. but whatever is possible.. at some point you will need to change around and if you forget what IP .. you will be in a mess.. so write it on a label and stick on the base of the router.. also without dhcp you will either need to reset router to factory using reset button or use static ip on the computer. )
3. Plug ethernet from LAN of the main router to LAN of the Netgear. Reboot the whole network is often necessary.
4. In your computer plugged somewhere in the network.. open browser and go to the address you set.. 10.0.1.250 in my example.
5. You can then setup the Netgear to do whatever you like.. DIsk access is fine.. wireless is fine.. it just cannot be a router.
Many many reboots if you get lost. Hit reset and start over.

How to set up the Time Capsule as an access point

Hi there,
I have home office and am having wifi-connectivity issues due to the layout of my home.
I'm getting the electrician to set up ethernet outlets in various rooms in my house so that I can get wired connections in several rooms. What I want to do is connect my Time Capsule to one of those ethernet ports (see the diagram below) so that I can still broadcast a wi-fi signal in my house while having wired connections elsewhere.
|->
Lan Port 1
Home Office (Laptop)
|
|->
Lan Port 2
Living Room (TV)
Modem
->
Wired Router
|
|->
Lan Port 3
2nd Bedroom (Xbox)
|
|->
Lan Port 4
Dining Room (Time Capsule)
In my research in how to set this up, I've come across documentation that shows how to convert an old Netgear/Linksys wifi router to an access point. Here's an example of the documentation I've run across: http://www.smallnetbuilder.com/wireless/wireless-basics/30338-how-to-convert-a-w ireless-router-into-an-access-point. What I haven't encountered is how to do this with a Time Capsule.
Here are my questions:
Do I just follow these instructions and substitute "Time Capsule" where the author references "AP"?
I currently have my network set up through the Time Capsule. Here are some of the things that I currently have set up and corresponding questions:
all computers can access the printer via wifi - under the above setup, will all computers (connected to the new network via wired OR wireless access) still have access to the printer?
I have my macbook set up as a media center for my xbox and PS3. The Xbox and PS3 connect to my macbook and access the movie files that I have saved on my Time Capsule and a 2nd HDD that is connected to the Time Capsule via USB - under the above setup, will I still be able to access those movies with my PS3 and Xbox via the macbook media center software?
Thanks a ton for any help or advice. It's much appreciated.

Excellent.. great to see people doing the job properly and wiring ethernet.
Here are my questions:
Do I just follow these instructions and substitute "Time Capsule" where the author references "AP"?
Apple system is slightly different.. although the AP method would work the TC has a programmed state for placing it in AP mode.
And Apple even documented it.
http://support.apple.com/kb/HT4260
The difference in your system, is you are not using an Apple primary router (I presume) but otherwise the same.
Any router setup as WAP, you bridge the router part.. and you use Same wireless name.. same security setting (WPA2 Personal is WPA2 AES and the only one suitable). Same passkey..
I would add one difference to the apple insstructions.. they depend on auto wireless channels working. IMHO, auto anything in wireless is akin to voodoo black arts and has more to do with beads and rattles than science. It works fine in some case.. terrible in others.. lock it down. Set the wireless yourself.. at 2.4ghz there are only 3 non overlapping channels.. 1, 6, 11 .. if you use 300mbit N on the main router, it will use 2 of those channels.. choose the third for the TC.
Of course the TC can also use 5ghz.. and I lock it down as well but that is more my control freak nature.. and strong skeptism of anything auto in the wireless world.
I currently have my network set up through the Time Capsule. Here are some of the things that I currently have set up and corresponding questions:
all computers can access the printer via wifi - under the above setup, will all computers (connected to the new network via wired OR wireless access) still have access to the printer?
I have my macbook set up as a media center for my xbox and PS3. The Xbox and PS3 connect to my macbook and access the movie files that I have saved on my Time Capsule and a 2nd HDD that is connected to the Time Capsule via USB - under the above setup, will I still be able to access those movies with my PS3 and Xbox via the macbook media center software?
Your number auto changed.. fun isn't it when i edit it shows correctly but when I post it changes the format.
On the new setup the printer will still be available to all clients .. whether wireless or wired.
And to second part, yes, all file access is not going to change.. well I don't predict any.. IP of the system might change around but overall you are creating a single flat network. And that will work fine.

How can I set up a guest access point with a Time Capsule and an Airport Extreme? I am using a Telus router with the Time Capsule used as a wireless access point (bridge mode). I don't want the guest access point to have access to my network.

How can I set up a guest access point with a Time Capsule and an Airport Extreme? I am using a Telus router with the Time Capsule used as a wireless access point (bridge mode). I don't want the guest access point to have access to my network.

The Guest Network function of the Time Capsule and AirPort Extreme cannot be enabled when the device is in Bridge Mode. Unfortunately, with another router...the Telus...upstream on your network, Bridge Mode is indicated as the correct setting for all other routers on the network.
If you can replace the Telus gateway with a simple modem (that performs no routing functions), you should be able to configure either the Time Capsule or the AirPort Extreme....whichever is connected to the modem....to provide a Guest Network.

Trying to set up BEFW11S4 as a "slave" router/access point

I want to set up the BEFW11S4 as a router and access point in the opposite corner of the house from the main wireless router. My main router is address 192.168.1.1, and I configured the BEFW11S4 as 192.168.1.2, with a different WEP key and turned off DHCP, so the main router will hand out addresses.
I am not able to ping the BEFW11S4, nor can I access it with IE. I have a CAT5 Ethernet cable going to the WAN port, and configured the WAN address as 192.168.1.1. I also have an Ethernet-connected PC to the BEFW11S4 and can't see it nor ping it.
What should I do to make this work?
Thanks,
Rocky

you need to connect the 2 routers using regular ports. example, from port 1 of main router going to port1 of befw11s4. do not configure the wan ip of befw11s4 anymore. it should only be set to "obtain an ip automatically".

Setting up a WRT150N as an Access Point.

Hello everyone! Today I bought a Linksys WRT150N router. I am trying to setup the router as a simple access point because I already have a router. My configuration is as follows: Modem > Draytek Vigor 2900V > Linksys WRT150N now my question is how to setup the linksys to work with the draytek. The Draytek has an IP address of 192.168.1.1 and subnet 255.255.255.0 Thanks in advance for the help!

I ran into a similar problem while setting up my wrt150n on my previous isp. The default ip address for the wrt150n is 192.168.1.1, see the problem? If you go into the setup for the router you can change the network address for the router to 192.168.2.1 and this should solve your problem. You can confirm with Linksys tech support that this is the problem, they were very helpful when I called them.

Set E1000 as an Access Point

I am wanting to setup my E1000 as an access point to an internet connected wired network so I can access the computers on the wired network and the internet. I attempted to use the Linksys "Guide Me" support, but it directed me to how to on another type of router using a different firmware. Does anyone have any suggestions?
Thank you,
Eric

Note that below when I say router I mean the modem/router
Assuming you wanted to know what the DHCP was assigning, it should be assigning the lower half of the 100s (it assigned 192.168.1.101). Gateway and DNS are set to the router itself.
Messing some more with it, it seems like it might actually be the E1000 blocking on it's LAN switch. Something connected behind it won't get DHCP, but if I manually assign it an address then I can hit both the E1000 and the router, but no DNS. Right now I'm thinking the E1000 is blocking DNS and DHCP requests. I'd tried turning off the firewall and unchecking everything as well, but no dice.

How do i set up a wireless access point with ny time capsule

I am using a new Airport Extreme and want to utilize my older TC to create a wireless access point or maybe an aditional router using the same newtwork. What are the steps to set this up?
Thanks
Alamo

You will first need to perform a Factory Default Reset on the Time Capsule.
Resetting an AirPort Base Station or Time Capsule FAQ
Then, temporarily locate it in close proximity (same room or nearby) to the AirPort Extreme.
Open Macintosh HD > Applications > Utilities > AirPort Utility
Click the tab in the upper left hand corner of the AirPort Utility window that reads Other AirPort Base Stations (1), then click the Time Capsule
AirPort Utility will take a moment or two to analyze your network, then announce that the TC will be configured to extend your wireless network.
Enter a name for the TC (you can use the same device name that you used before if you wish) and click Next.
AirPort Utility will take a another minute or two to configure the TC and then tell you that the setup is complete. Click Done
At this point, power down the TC and move it to a location that is approximately half the distance from the AirPort Extreme and the area that needs more wireless coverage.....to give the TC a good strong signal to "extend"
Power up the TC and wait for the green light and then you are all set.

A tech company just set up a wifi network in my house and does not use my existing TC; how do I get it in the network to serve as backup for my iMac? (I don't need it as a wifi access point anymore)

a tech company just set up a wifi network in my house and does not use my existing TC; how do I get it in the network to serve as backup for my iMac? (I don't need it as a wifi access point anymore) thanks

Just bridge the TC and plug it by ethernet into the main router.
Bridge in v5 airport utility.
In v6 it is under network.. change it from DHCP and NAT to Off bridge mode.
Turn off the wireless.

Access point setting

Similar Messages

Maybe you are looking for