Access Restriction on EA3500 does not work.

I tested this with my laptop by setting its access restriction/parental control to always not access the internet. But still my laptop can still search through wikipedia. Is this because of the router firmware? By the way I'm using the latest Connect cloud firmware. Thanks in advance.

I believe parental control is not really busted, it's just designed to work only with ipv4. What you can try though is to try the following:
Make sure that the laptop is only wirelessly connected to the router, because if the laptop was connected both wired and wireless then parental controls will not work since the laptop will be using two adapters.
Remove the entry under target devices, disable parental controls and save the settings.
Enable parental controls, add a target device, save the settings
Try to check if you can access wikipedia or other website because if parental control was working then it should add for a password
Try also to check the router's status tab if there's an ipv6 ip address because if there is, then parental controls will not work

Similar Messages

  • Access to Outlook Anywhere does not work

    Good evening,
    I recently installed an Exchange Server 2013 CAS / MB.
    Until now, the server presented a few errors (mainly in the
    event log) that does not seem to significantly influence functionality.
    This week I published the server on the Internet and verified various malfunctions
    related to the access from outside.
    In particular from outside:
    1 - OWA does not work with Windows integrated authentication, it works with the Forms based authentication;
    2 - Outlook Anywhere does not work from internet.
    I've done a lot of research and testing without success.
    With regard to the first issue (which is not a priority but can relate to second one)
    add that in Firefox I get a first authentication request. If
    I enter credentials it ask again for identical authentication (repeatly), if I cancel it shows a second one that instead allows me access (are slightly different).
    I assume that the first is the integrated Windows application and the second is basic authentication.
    Internet Explorer shows me only the first authentication request and if I cancel shows blank page.
    The problem is
    priority 2:
    Outlook connects without problems on LAN network, the Internet
    seems to download the correct information
    (autodiscover), but then does not connect
    to the server (connection to Microsoft Exchange is unavailable).
    If you manually edit the settings,
    auto-configuration server returns as
    a [email protected]. If I change
    manually the server (and proxy settings
    http), the result does not change.
    - Setting information -
    The server is installed
    in the LAN network and is exposed on the Internet through
    a firewall (Pat on port 443, et al. not 80)
    on a public address.
    The public and private DNS have been configured with a
    host record (A) and two
    CNAME (webmail and autodiscover).
    The internal Outlook clients connect
    with autodiscover and HTTPS /
    NTLM / SSL (Outlook connectivity
    status).
    IMAP, SMTP, POP, ActiveSync function.
    Exchange remote connectivity analizer retrieves Autodiscover information but doesn't pass test for RPC/HTTP access (it discard accesson
    port 443 and try port 80, SPF isn't configured).
    The navigation to the url
    https://proxyexternalURL/rpc/rpcproxy.dll  has the same behaviour like problem 1.
    Test-OutlookConnectivity returns unmanaged error ('WARNING: An unexpected error has occurred and a Watson dump is being generated: Failed to find the probe result for invoke now request id -- and probe workdefinition id --').
    Errors in eventviewer: 5011 - WAS (one time), 139 - MSExchange OWA (some not ripetitive), 3028 - MSExchangeApplicationLogic (every 6 hours), 106 - MSExchange common (many during working hour), 65535 - application (some at nighttime 00.00 - 03.00 a.m.), 1006
    - MSExchangeDiagnostic (every 30 min), 6002 - MSExchange Mid-Tier Storage (about every 5 minutes), 5 - MSExcahnge Workload Management (one time).
    Ask for further information.
    - Cmdlet and Autodiscover output -
    Get-OutlookAnywhere | fl name,*auth*,*ssl*,*host*
    Name                               : Rpc (Default Web site)
    ExternalClientAuthenticationMethod : Basic
    InternalClientAuthenticationMethod : Ntlm
    IISAuthenticationMethods           : {Basic, Ntlm, Negotiate}
    SSLOffloading                      : True
    ExternalClientsRequireSsl          : True
    InternalClientsRequireSsl          : True
    ExternalHostname                   : webmail.name_domain.test
    InternalHostname                   : webmail.name_domain.test
    Get-OutlookProvider | ft -autosize
    Name     Server CertPrincipalName                      TTL
    EXCH            msstd:webmail.name_domain.test         1  
    EXPR             msstd:webmail.name_domain.test         1  
    WEB                                              
         1  
    Get-AutodiscoverVirtualDirectory | fl name,*auth*,*url*
    Name                          : Autodiscover (Default Web site)
    InternalAuthenticationMethods : {Basic, WSSecu.testy, OAuth}
    ExternalAuthenticationMethods : {Basic, WSSecu.testy, OAuth}
    LiveIdNegotiateAuthentication : False
    WSSecu.testyAuthentication      : True
    LiveIdBasicAuthentication     : False
    BasicAuthentication           : True
    DigestAuthentication          : False
    WindowsAuthentication         : False
    OAuthAuthentication           : True
    AdfsAuthentication            : False
    InternalUrl                   :
    ExternalUrl                   :
    Get-MapiVirtualDirectory | fl name,*auth*,*url*
    Name                          : mapi (Default Web site)
    IISAuthenticationMethods      : {Basic, Ntlm, Negotiate}
    InternalAuthenticationMethods : {Basic, Ntlm, Negotiate}
    ExternalAuthenticationMethods : {Basic, Ntlm, Negotiate}
    InternalUrl                   : https://webmail.name_domain.test/mapi
    ExternalUrl                   : https://webmail.name_domain.test/mapi
    Autodiscover.xml
    <?xml version="1.0" encoding="utf-8"?>
    <Autodiscover xmlns="http://schemas.microsoft.com/exchange/autodiscover/responseschema/2006">
      <Response xmlns="http://schemas.microsoft.com/exchange/autodiscover/outlook/responseschema/2006a">
        <User>
          <DisplayName>user</DisplayName>
          <LegacyDN>/o=organization_name/ou=Exchange Administrative Group (FYDIBOHF23SPDLT)/cn=Recipients/cn=e4c0c18c8f214afbb5152bb08823179d-user</LegacyDN>
          <AutoDiscoverSMTPAddress>user@name_domain.test</AutoDiscoverSMTPAddress>
          <DeploymentId>d60c71c9-3740-404c-a38c-aa24e6105432</DeploymentId>
        </User>
        <Account>
          <AccountType>email</AccountType>
          <Action>settings</Action>
          <MicrosoftOnline>False</MicrosoftOnline>
          <Protocol>
            <Type>EXCH</Type>
            <Server>72036b30-a4d4-4b42-9c39-445bd04c23a6@name_domain.test</Server>
            <ServerDN>/o=organization_name/ou=Exchange Administrative Group (FYDIBOHF23SPDLT)/cn=Configuration/cn=Servers/cn=72036b30-a4d4-4b42-9c39-445bd04c23a6@name_domain.test</ServerDN>
            <ServerVersion>73C082C8</ServerVersion>
            <MdbDN>/o=organization_name/ou=Exchange Administrative Group (FYDIBOHF23SPDLT)/cn=Configuration/cn=Servers/cn=72036b30-a4d4-4b42-9c39-445bd04c23a6@name_domain.test/cn=Microsoft Private MDB</MdbDN>
            <PublicFolderServer>webmail.name_domain.test</PublicFolderServer>
            <AD>DC2.name_domain.test</AD>
            <ASUrl>https://webmail.name_domain.test/EWS/Exchange.asmx</ASUrl>
            <EwsUrl>https://webmail.name_domain.test/EWS/Exchange.asmx</EwsUrl>
            <EmwsUrl>https://webmail.name_domain.test/EWS/Exchange.asmx</EmwsUrl>
            <EcpUrl>https://webmail.name_domain.test/ecp/</EcpUrl>
            <EcpUrl-um>?rfr=olk&amp;p=customize/voicemail.aspx&amp;exsvurl=1&amp;realm=name_domain.test</EcpUrl-um>
            <EcpUrl-aggr>?rfr=olk&amp;p=personalsettings/EmailSubscriptions.slab&amp;exsvurl=1&amp;realm=name_domain.test</EcpUrl-aggr>
            <EcpUrl-mt>PersonalSettings/DeliveryReport.aspx?rfr=olk&amp;exsvurl=1&amp;IsOWA=&lt;IsOWA&gt;&amp;MsgID=&lt;MsgID&gt;&amp;Mbx=&lt;Mbx&gt;&amp;realm=name_domain.test</EcpUrl-mt>
            <EcpUrl-ret>?rfr=olk&amp;p=organize/retentionpolicytags.slab&amp;exsvurl=1&amp;realm=name_domain.test</EcpUrl-ret>
            <EcpUrl-sms>?rfr=olk&amp;p=sms/textmessaging.slab&amp;exsvurl=1&amp;realm=name_domain.test</EcpUrl-sms>
            <EcpUrl-publish>customize/calendarpublishing.slab?rfr=olk&amp;exsvurl=1&amp;FldID=&lt;FldID&gt;&amp;realm=name_domain.test</EcpUrl-publish>
            <EcpUrl-photo>PersonalSettings/E.testAccount.aspx?rfr=olk&amp;chgPhoto=1&amp;exsvurl=1&amp;realm=name_domain.test</EcpUrl-photo>
            <EcpUrl-tm>?rfr=olk&amp;ftr=TeamMailbox&amp;exsvurl=1&amp;realm=name_domain.test</EcpUrl-tm>
            <EcpUrl-tmCreating>?rfr=olk&amp;ftr=TeamMailboxCreating&amp;SPUrl=&lt;SPUrl&gt;&amp;.testle=&lt;.testle&gt;&amp;SPTMAppUrl=&lt;SPTMAppUrl&gt;&amp;exsvurl=1&amp;realm=name_domain.test</EcpUrl-tmCreating>
            <EcpUrl-tmE.testing>?rfr=olk&amp;ftr=TeamMailboxE.testing&amp;Id=&lt;Id&gt;&amp;exsvurl=1&amp;realm=name_domain.test</EcpUrl-tmE.testing>
            <EcpUrl-extinstall>Extension/InstalledExtensions.slab?rfr=olk&amp;exsvurl=1&amp;realm=name_domain.test</EcpUrl-extinstall>
            <OOFUrl>https://webmail.name_domain.test/EWS/Exchange.asmx</OOFUrl>
            <UMUrl>https://webmail.name_domain.test/EWS/UM2007Legacy.asmx</UMUrl>
            <OABUrl>https://webmail.name_domain.test/OAB/e66d9a4a-6ed2-4512-b72f-522381524dd9/</OABUrl>
            <ServerExclusiveConnect>off</ServerExclusiveConnect>
            <CertPrincipalName>msstd:webmail.name_domain.test</CertPrincipalName>
          </Protocol>
          <Protocol>
            <Type>EXPR</Type>
            <Server>webmail.name_domain.test</Server>
            <SSL>On</SSL>
            <AuthPackage>Basic</AuthPackage>
            <ASUrl>https://webmail.name_domain.test/ews/exchange.asmx</ASUrl>
            <EwsUrl>https://webmail.name_domain.test/ews/exchange.asmx</EwsUrl>
            <EmwsUrl>https://webmail.name_domain.test/ews/exchange.asmx</EmwsUrl>
            <EcpUrl>https://webmail.name_domain.test/ecp/</EcpUrl>
            <EcpUrl-um>?rfr=olk&amp;p=customize/voicemail.aspx&amp;exsvurl=1&amp;realm=name_domain.test</EcpUrl-um>
            <EcpUrl-aggr>?rfr=olk&amp;p=personalsettings/EmailSubscriptions.slab&amp;exsvurl=1&amp;realm=name_domain.test</EcpUrl-aggr>
            <EcpUrl-mt>PersonalSettings/DeliveryReport.aspx?rfr=olk&amp;exsvurl=1&amp;IsOWA=&lt;IsOWA&gt;&amp;MsgID=&lt;MsgID&gt;&amp;Mbx=&lt;Mbx&gt;&amp;realm=name_domain.test</EcpUrl-mt>
            <EcpUrl-ret>?rfr=olk&amp;p=organize/retentionpolicytags.slab&amp;exsvurl=1&amp;realm=name_domain.test</EcpUrl-ret>
            <EcpUrl-sms>?rfr=olk&amp;p=sms/textmessaging.slab&amp;exsvurl=1&amp;realm=name_domain.test</EcpUrl-sms>
            <EcpUrl-publish>customize/calendarpublishing.slab?rfr=olk&amp;exsvurl=1&amp;FldID=&lt;FldID&gt;&amp;realm=name_domain.test</EcpUrl-publish>
            <EcpUrl-photo>PersonalSettings/E.testAccount.aspx?rfr=olk&amp;chgPhoto=1&amp;exsvurl=1&amp;realm=name_domain.test</EcpUrl-photo>
            <EcpUrl-tm>?rfr=olk&amp;ftr=TeamMailbox&amp;exsvurl=1&amp;realm=name_domain.test</EcpUrl-tm>
            <EcpUrl-tmCreating>?rfr=olk&amp;ftr=TeamMailboxCreating&amp;SPUrl=&lt;SPUrl&gt;&amp;.testle=&lt;.testle&gt;&amp;SPTMAppUrl=&lt;SPTMAppUrl&gt;&amp;exsvurl=1&amp;realm=name_domain.test</EcpUrl-tmCreating>
            <EcpUrl-tmE.testing>?rfr=olk&amp;ftr=TeamMailboxE.testing&amp;Id=&lt;Id&gt;&amp;exsvurl=1&amp;realm=name_domain.test</EcpUrl-tmE.testing>
            <EcpUrl-extinstall>Extension/InstalledExtensions.slab?rfr=olk&amp;exsvurl=1&amp;realm=name_domain.test</EcpUrl-extinstall>
            <OOFUrl>https://webmail.name_domain.test/ews/exchange.asmx</OOFUrl>
            <UMUrl>https://webmail.name_domain.test/ews/UM2007Legacy.asmx</UMUrl>
            <OABUrl>https://webmail.name_domain.test/OAB/e66d9a4a-6ed2-4512-b72f-522381524dd9/</OABUrl>
            <ServerExclusiveConnect>on</ServerExclusiveConnect>
            <CertPrincipalName>msstd:webmail.name_domain.test</CertPrincipalName>
            <EwsPartnerUrl>https://webmail.name_domain.test/ews/exchange.asmx</EwsPartnerUrl>
            <GroupingInformation>LAN</GroupingInformation>
          </Protocol>
          <Protocol>
            <Type>WEB</Type>
            <Internal>
              <OWAUrl AuthenticationMethod="Basic, Fba">https://webmail.name_domain.test/</OWAUrl>
              <Protocol>
                <Type>EXCH</Type>
                <ASUrl>https://webmail.name_domain.test/EWS/Exchange.asmx</ASUrl>
              </Protocol>
            </Internal>
            <External>
              <OWAUrl AuthenticationMethod="Basic">https://webmail.name_domain.test/</OWAUrl>
              <Protocol>
                <Type>EXPR</Type>
                <ASUrl>https://webmail.name_domain.test/ews/exchange.asmx</ASUrl>
              </Protocol>
            </External>
          </Protocol>
          <Protocol>
            <Type>EXHTTP</Type>
            <Server>webmail.name_domain.test</Server>
            <SSL>On</SSL>
            <AuthPackage>Ntlm</AuthPackage>
            <ASUrl>https://webmail.name_domain.test/EWS/Exchange.asmx</ASUrl>
            <EwsUrl>https://webmail.name_domain.test/EWS/Exchange.asmx</EwsUrl>
            <EmwsUrl>https://webmail.name_domain.test/EWS/Exchange.asmx</EmwsUrl>
            <EcpUrl>https://webmail.name_domain.test/ecp/</EcpUrl>
            <EcpUrl-um>?rfr=olk&amp;p=customize/voicemail.aspx&amp;exsvurl=1&amp;realm=name_domain.test</EcpUrl-um>
            <EcpUrl-aggr>?rfr=olk&amp;p=personalsettings/EmailSubscriptions.slab&amp;exsvurl=1&amp;realm=name_domain.test</EcpUrl-aggr>
            <EcpUrl-mt>PersonalSettings/DeliveryReport.aspx?rfr=olk&amp;exsvurl=1&amp;IsOWA=&lt;IsOWA&gt;&amp;MsgID=&lt;MsgID&gt;&amp;Mbx=&lt;Mbx&gt;&amp;realm=name_domain.test</EcpUrl-mt>
            <EcpUrl-ret>?rfr=olk&amp;p=organize/retentionpolicytags.slab&amp;exsvurl=1&amp;realm=name_domain.test</EcpUrl-ret>
            <EcpUrl-sms>?rfr=olk&amp;p=sms/textmessaging.slab&amp;exsvurl=1&amp;realm=name_domain.test</EcpUrl-sms>
            <EcpUrl-publish>customize/calendarpublishing.slab?rfr=olk&amp;exsvurl=1&amp;FldID=&lt;FldID&gt;&amp;realm=name_domain.test</EcpUrl-publish>
            <EcpUrl-photo>PersonalSettings/E.testAccount.aspx?rfr=olk&amp;chgPhoto=1&amp;exsvurl=1&amp;realm=name_domain.test</EcpUrl-photo>
            <EcpUrl-tm>?rfr=olk&amp;ftr=TeamMailbox&amp;exsvurl=1&amp;realm=name_domain.test</EcpUrl-tm>
            <EcpUrl-tmCreating>?rfr=olk&amp;ftr=TeamMailboxCreating&amp;SPUrl=&lt;SPUrl&gt;&amp;.testle=&lt;.testle&gt;&amp;SPTMAppUrl=&lt;SPTMAppUrl&gt;&amp;exsvurl=1&amp;realm=name_domain.test</EcpUrl-tmCreating>
            <EcpUrl-tmE.testing>?rfr=olk&amp;ftr=TeamMailboxE.testing&amp;Id=&lt;Id&gt;&amp;exsvurl=1&amp;realm=name_domain.test</EcpUrl-tmE.testing>
            <EcpUrl-extinstall>Extension/InstalledExtensions.slab?rfr=olk&amp;exsvurl=1&amp;realm=name_domain.test</EcpUrl-extinstall>
            <OOFUrl>https://webmail.name_domain.test/EWS/Exchange.asmx</OOFUrl>
            <UMUrl>https://webmail.name_domain.test/EWS/UM2007Legacy.asmx</UMUrl>
            <OABUrl>https://webmail.name_domain.test/OAB/e66d9a4a-6ed2-4512-b72f-522381524dd9/</OABUrl>
            <ServerExclusiveConnect>On</ServerExclusiveConnect>
            <CertPrincipalName>msstd:webmail.name_domain.test</CertPrincipalName>
          </Protocol>
          <Protocol>
            <Type>EXHTTP</Type>
            <Server>webmail.name_domain.test</Server>
            <SSL>On</SSL>
            <AuthPackage>Basic</AuthPackage>
            <ASUrl>https://webmail.name_domain.test/ews/exchange.asmx</ASUrl>
            <EwsUrl>https://webmail.name_domain.test/ews/exchange.asmx</EwsUrl>
            <EmwsUrl>https://webmail.name_domain.test/ews/exchange.asmx</EmwsUrl>
            <EcpUrl>https://webmail.name_domain.test/ecp/</EcpUrl>
            <EcpUrl-um>?rfr=olk&amp;p=customize/voicemail.aspx&amp;exsvurl=1&amp;realm=name_domain.test</EcpUrl-um>
            <EcpUrl-aggr>?rfr=olk&amp;p=personalsettings/EmailSubscriptions.slab&amp;exsvurl=1&amp;realm=name_domain.test</EcpUrl-aggr>
            <EcpUrl-mt>PersonalSettings/DeliveryReport.aspx?rfr=olk&amp;exsvurl=1&amp;IsOWA=&lt;IsOWA&gt;&amp;MsgID=&lt;MsgID&gt;&amp;Mbx=&lt;Mbx&gt;&amp;realm=name_domain.test</EcpUrl-mt>
            <EcpUrl-ret>?rfr=olk&amp;p=organize/retentionpolicytags.slab&amp;exsvurl=1&amp;realm=name_domain.test</EcpUrl-ret>
            <EcpUrl-sms>?rfr=olk&amp;p=sms/textmessaging.slab&amp;exsvurl=1&amp;realm=name_domain.test</EcpUrl-sms>
            <EcpUrl-publish>customize/calendarpublishing.slab?rfr=olk&amp;exsvurl=1&amp;FldID=&lt;FldID&gt;&amp;realm=name_domain.test</EcpUrl-publish>
            <EcpUrl-photo>PersonalSettings/E.testAccount.aspx?rfr=olk&amp;chgPhoto=1&amp;exsvurl=1&amp;realm=name_domain.test</EcpUrl-photo>
            <EcpUrl-tm>?rfr=olk&amp;ftr=TeamMailbox&amp;exsvurl=1&amp;realm=name_domain.test</EcpUrl-tm>
            <EcpUrl-tmCreating>?rfr=olk&amp;ftr=TeamMailboxCreating&amp;SPUrl=&lt;SPUrl&gt;&amp;.testle=&lt;.testle&gt;&amp;SPTMAppUrl=&lt;SPTMAppUrl&gt;&amp;exsvurl=1&amp;realm=name_domain.test</EcpUrl-tmCreating>
            <EcpUrl-tmE.testing>?rfr=olk&amp;ftr=TeamMailboxE.testing&amp;Id=&lt;Id&gt;&amp;exsvurl=1&amp;realm=name_domain.test</EcpUrl-tmE.testing>
            <EcpUrl-extinstall>Extension/InstalledExtensions.slab?rfr=olk&amp;exsvurl=1&amp;realm=name_domain.test</EcpUrl-extinstall>
            <OOFUrl>https://webmail.name_domain.test/ews/exchange.asmx</OOFUrl>
            <UMUrl>https://webmail.name_domain.test/ews/UM2007Legacy.asmx</UMUrl>
            <OABUrl>https://webmail.name_domain.test/OAB/e66d9a4a-6ed2-4512-b72f-522381524dd9/</OABUrl>
            <ServerExclusiveConnect>On</ServerExclusiveConnect>
            <CertPrincipalName>msstd:webmail.name_domain.test</CertPrincipalName>
          </Protocol>
        </Account>
      </Response>
    </Autodiscover>
    Get-OwaVirtualDirectory | fl name,*auth*,*url*
    Name                          : owa (Default Web Site)
    ClientAuthCleanupLevel        : High
    InternalAuthenticationMethods : {Basic, Fba}
    BasicAuthentication           : True
    WindowsAuthentication         : False
    DigestAuthentication          : False
    FormsAuthentication           : True
    LiveIdAuthentication          : False
    AdfsAuthentication            : False
    OAuthAuthentication           : False
    ExternalAuthenticationMethods : {Basic}
    Url                           : {}
    SetPhotoURL                   :
    Exchange2003Url               :
    FailbackUrl                   :
    InternalUrl                   : https://webmail.name_domain.test/
    ExternalUrl                   : https://webmail.name_domain.test/

    Follow the results of the test
    Outlook Anywhere (RPC over HTTP).
    Has been used an account for which
    outlook anywhere works. The account
    for which the outlook anywhere does not work is
    an administrative account and therefore
    can not be used in the test.
    Autodiscovery returns the
    same result for both mailbox.
    I'm testing RPC/HTTP connectivity.
    Testing RPC over HTTP has not been exceeded.
    Test steps
    Microsoft connectivity Analyzer is attempting to test the Autodiscover service for user_test@domain_name.test.
    Test the Autodiscover service has not been exceeded.
    Test steps
    I'm trying to contact the Autodiscover service with each method available.
    I was not able to contact the Autodiscover service with no method.
    Test steps
    I'm trying to test the possible URL for the Autodiscover service https://domain_name.test/AutoDiscover/AutoDiscover.xml
    The test of this potential URL for the Autodiscover service has not been exceeded.
    Test steps
    I'm trying to resolve the host name domain_name. DNS test.
    I was able to resolve the host name.
    IP addresses are returned: xxx.yyy.zzz.www
    I'm testing the TCP port 443 on the host domain_name. tests to check that is open and listening.
    The door has been opened properly.
    I'm testing the validity of your SSL certificate.
    The SSL certificate has not exceeded one or more validation controls.
    Test steps
    Microsoft connectivity Analyzer is attempting to obtain the SSL certificate from the remote server domain_name. test on port 443.
    Microsoft connectivity Analyzer got the remote SSL certificate.
    Remote certificate subject: E = it_staff@domain_name.test, CN = * domain_name. test, OU = it staff, O = domain_name, L = city, S = state, C = test issuer: E = it_staff@domain_name.test, CN = * domain_name. test, OU = it staff, O = domain_name,
    L = city, S = state, C = test.
    I am validating the certificate name.
    I could not validate the certificate name.
    More info about this issue and how to resove it
    The host name domain_name. testing does not match any name found on the certificate and server = it_staff@domain_name.test, CN = * domain_name. test, OU = it staff, O = domain_name, L = city, S = state, C = test.
    I'm trying to test the possible URL for the Autodiscover service https://autodiscover.domain_name.test/AutoDiscover/AutoDiscover.xml
    The test of this potential URL for the Autodiscover service has not been exceeded.
    Test steps
    I'm trying to resolve the host name autodiscover. domain_name. DNS test.
    I was able to resolve the host name.
    IP addresses are returned: xxx.yyy.zzz.kkk
    I'm testing the TCP port 443 on the host autodiscover. domain_name. tests to check that is open and listening.
    The door has been opened properly.
    I'm testing the validity of your SSL certificate.
    The SSL certificate has not exceeded one or more validation controls.
    Test steps
    Microsoft connectivity Analyzer is attempting to obtain the SSL certificate from the remote server autodiscover. domain_name. test on port 443.
    Microsoft connectivity Analyzer got the remote SSL certificate.
    Other details
    Remote certificate subject: CN = webmail. domain_name. test, OU = it staff, O = domain_name, L = city, S = city, C = test issuer: CN = domain_name-DC1-CA, DC = domain_name, DC = test.
    I am validating the certificate name.
    I validated the certificate name.
    Other details
    I found the host name autodiscover. domain_name. test in the voice of the alternative name of the certificate object.
    Elapsed time: 1 ms.
    I am validating the reliability of certificates.
    I was not able to validate the reliability of the certificate.
    Test steps
    Microsoft connectivity Analyzer is attempting to generate certificate chains to a certificate CN = webmail. domain_name. test, OU = it staff, O = domain_name, L = city, S = city, C = test.
    I failed to build a certificate chain for the certificate.
    Other details
    Failed to generate the certificate chain.
    May be missing the required intermediate certificates.
    I'm trying to contact the Autodiscover service using the HTTP redirect method.
    I was not able to contact the Autodiscover service using the HTTP redirect method.
    Test steps
    I'm trying to resolve the host name autodiscover. domain_name. DNS test.
    I was able to resolve the host name.
    IP addresses are returned: xxx.yyy.zzz.kkk
    I'm testing the TCP port 80 on the host autodiscover. domain_name. tests to check that is open and listening.
    The specified port is blocked, is not listening or doesn't produce the expected response.
    More info about this issue and how to resove it
    I encountered a network error while communicating with the remote host.
    I'm trying to
    find the
    SRV DNS record _audiscover._tcp.domain_name.test.
    I failed to find
    the SRV record of the
    Autodiscover service
    in DNS.
    Some clarifications:
    1 - xxx.yyy.zzz.www and xxx.yyy.zzz.kkk
    are two static public addresses
    of which only the latter exposes Exchange services;
    2 - The certificate
    *. Domain_name.test is not related
    to Exchange services;
    3 -I imported the certificate
    of the issuing CA on the standalone test PC to validate the certificate.
    3- The port 80 is not open and are not published SRV records.
    Best regards.

  • Access Restrictions - Blocked Applications does not save

    Under the Access Restrictions section it is possible to Block Applications.
    I enter a name for the application, the port range (from and to) and whether it is TCP, UDP or both. I then hit ADD which adds the application to the list of Blocked Applications in the box above. I then scroll down thru that box to find the App and [>>] add it to the Blocked List. I then hit SAVE SETTINGS
    Upon returning to the policy and the Blocked Apps list the record I just created is nowhere to be found. Not in the Blocked List or under Applications.
    What gives ???

    Wireless-N Gigabit Router
    Model: WRT310N
    Firmware Version: v1.0.06
    All PCs run VISTA
    I don't see how a HARD RESET and POWER RECYCLE creates a fix for this. All that does is reboot the existing firmware and causes me to have to reenter all the router and security settings. The documentation for the lastest firmware (version Ver.1.0.9 build 4 12/11/2009) and the previous upgrade (1.0.07 build 14) does not include references to a fix for this problem. Has this been identified before and what firmware version is the fix included in ?
    I have held off performing the 1.0.9 firmware upgrade as I have no confidence that this will fix this problem.

  • Problem with my iPod touch: Frozen screen, unable to access anything as slider does not work, will not accept a full restore.  Apple Store advised that it is a 'hardware' problem and I could trade-in!

    I am a relatively 'new' user.  Touch was a gift, I used it in a simplistic way - listened to music took a few photos, added a few calendar events.  After a year I then decided to be more proactive and found a few free apps (Solitaire) - then had a the frozen screen problem which I though was connected to low battery, but it wasn't.  I recharged it, still could not access, then tried a full restore and got an error message.  Took it to a Genius Bar and was told it was a hardware problem and as it is out of warranty  I could trade in or just buy a different product.  As this is my first Apple product is this usual?  Do Apple products have a very short shelf life - I anticipated that it would last me longer than a year!  Has anyone else had this problem?  Was it able to be resolved? Or is it worth trying to get it repaired - and if so who can do it - Apple  Store did not offer that to me as an option?

    Sure sounds like a hardware problem. It happens some times. The iPod is just an electrical device.
    Apple will exchange it for a refurbished one for this price. Apple does not repair your iPod.
    Apple - Support - iPod - Repair pricing
    A third-party place like the following maybe less expensive. Google for more places.
    iPhone Repair, Service & Parts: iPod Touch, iPad, MacBook Pro Screens

  • Restricting by 0MAT_PLANT does not work

    All,
    0MAT_PLANT is a compound of 0MATERIAL and 0PLANT.
    When I try to restrict a query by 0MAT_PLANT I am expecting that it's by Plant and material
    Example:
    Query with no restrictions:
    0MAT_PLANT
    001/1000123
    001/1000124
    002/1000123
    002/1000123
    Then when I restrict by:  001/1000123 I get the following
    0MAT_PLANT
    001/1000123
    002/1000123
    I was expecting this:
    0MAT_PLANT
    001/1000123
    BW doesn't seem to hold the plant value in the restriction.  Is there something that I can do to make this restriction work?
    Thanks,
    Chris

    Bump

  • How do you get out of guided access if the password does not work

    HOw do i access my phone, if the guided access is on but i dont remember the password?

    Hey BeastStitch,
    You can end a Guided Access session by triple clicking the home button on your iPhone. See this article for reference -
    iOS: About Guided Access - Apple Support
    Thanks for using Apple Support Communities.
    Be well,
    Brett L 

  • I am trying to allow guests on windows to connect to shares on my Lion server but it keeps asking for a password for guest. I have allow guest users to access this share enabled but it still does not work.

    I am trying to allow guests on windows to connect to shares on my Lion server but it keeps asking for a password for guest. I have allow guest users to access this share enabled but it still does not work.

    Ditto. Guest accounts shouldn't have a password. No way to enter one in System Prefs...

  • Safari 5.1.1 I no longer have access to my bookmark folders, just a search that does not work well. How can I retrieve access to bookmark folders?

    OS 10.6.8 Safari 5.1.1 I no longer have access to the bookmark folders. There is just a search function that does not work well. Is there any way to get access back to my bookmark folders?

    This site didn't say anything about one wrong ID, but only talks about changing the Apple ID.  If it didn't work the first time why should it work now?

  • HT1222 I just installed this update and now I cannot access "Mail" at all.  I tried reinstalling the program, but that does not work, either.  Help!!!!!!

    I just installed this update and now I cannot access "Mail" at all.  I tried reinstalling the program, but that does not work, either.  Help!

    Paldeng, thanks for the suggestion.  I've done all that.  I can connect to the server, but apparently they are not recognizing my ID and password.  I can use the server program if I don't go through Mail (using the same ID and password).  My mother in another state with another provider has had the same email issue, as also my husband on his laptop who uses the same internet connection I do.  His worked fine until we had it repaired at the Apple store and all the original programs reloaded (with the required updates, I assume).  We can receive email in Mail, we just cannot send.
    I contacted my service provider, and we went over my connections.  They said it was not their problem and connected me with Apple, resulting in a charge to me because my warranty is long expired.  Apple swears it is not their problem, it is the provider, so here I sit.  My son was able to fix my Mom's Mail (she's 97) and got my husband's working also, until mine went out, by tweaking connection descriptions and ports remotely.  The thing is, we had not messed with any of those settings, so what changed?  I just did not want to bother my son again, as he has many other demands on his time.
    Since this fiasco with the Mail v4.6 update, I'm wondering if something else was updated that works well with Lion and Mountain Lion, but does not work well with Snow Leopard and Leopard.  I think the problem I had with the Mail update was that my Mail program had been renamed to Mail (original), and therefore was not being recognized by the update.  Perhaps they had another tweak in there somewhere that is affecting outgoing mail connections?

  • Hello everybody,i've forgot my apple password and i wanted to reset it to a new one but i also forgot the security question and the alternative email does not work and i am really need to log in to my apple i d because my iPhone 4g won't  let me access it

    Hello everybody,i've forgot my apple password and i wanted to reset it to a new one but i also forgot the security question and the alternative email does not work and i am really need to log in to my apple i d because my iPhone 4g won't  let me access it so anyone can help me with it or can i put another apple id to it without putting the first password?THANKS FOR YOUR HELP.

    Then call AppleCare and talk to someone in account security.

  • I have iMovie '11, and I am unable to access mpeg HD video files that I want to edit.  The files are fine (I can open and watch them using VLC), but I cannot seem to import the files into iMovie. File Import does not work.  Any suggestions??

    More detail: I have a bunch of mpeg HD video files that were shot on a SONY HDR-HC3 Handycam camcorder.  I would like to edit these into a single video production.  I can access and view the mpeg files using VLC (Quicktime does not work with them).  However, I seem to be unable to get the mpeg files to interface with iMovie '11 -- I cannot use the File --> Import command, nor can I drag-and-drop them into iMovie.
    Is there something anyone might suggest to get this to work?  Or are these files incompatible with iMovie?  If so, I assume I must purchase a different video editing software program (e.g. Adobe Premeir Pro).  Suggestions???
    Many thanks in advance for your time and consideration

      Yes, I tried that.   The files were ordered by their original numbers as imported from the camera, but I batched them through Phocoshop to downsize all of them into a more manageable file size.   I opened that destination folder from quick time  from where it said select image sequence.   I clicked on the first one and opened it.   The result was a large image with an arrow indicating a movie was ready to go.   When I pressed the arrow, though, I realized it had only imported that one frame so there was no movie.   The files are Jpgs and are about 450 KB each. 
        To your knowledge are there any links to iMovie tutorials or quick time tutorials that may address this situation?  Maybe there will be one I haven't looked at yet. 
        Thanks

  • Link does not work for-End-of-Sale and End-of-Life Announcement for the Cisco Secure Access Control System 5.4

    Link does not work for
    End-of-Sale and End-of-Life Announcement for the Cisco Secure Access Control System 5.4
    How do we get Cisco to fix?
    see attachment

    Give it a couple of days - it looks like they just sent out the notification before the notice was published on the public page.
    Once the ACS 5.4 EoS/EoL notice is published you should see it linked from this page.

  • Save a published Access services database site as a template with contents does not work

    Hi
    I have a Access site on the SharePoint. I wanted the site to be duplicated to another subsite, I then did the usual - save site as a template with contents and made a copy of it, however it does not work. I have been getting the error as stated below
     error has occurred during report processing. (rsProcessingAborted)
    Query execution failed for dataset 'Default'. (rsErrorExecutingCommand)
    For more information about this error navigate to the report server on the local server machine, or enable remote errors
    However, it works if I make a local copy and publish it to the subsite? How does access services work on SharePoint and why the template option can't be chosen.

    Hi cally, check the following links for possible solutions:
    https://social.msdn.microsoft.com/Forums/sqlserver/en-US/1e2b77ba-4cfa-4aa3-97e4-b7b39fbd46fd/error-with-ssrs-report-that-has-a-sharepoint-list-data-connection-ssrs-r2-and-sharepoint-2010?forum=sqlreportingservices
    http://blog.mikehacker.net/2012/05/16/sharepoint-2010-access-services-reporting-with-sql-2012/
    cameron rautmann

  • My passcode is working to unlock the screen but does not work with restriction passcode. Should they be different?

    My passcode is working to unlock the screen but does not work with restriction passcode.
    Tried it several times but it did not work, though i can use the phone and all features even after 13 failed attempts.
    Should restriction passcode be different from what i set?

    There is no default restriction password. If you didn't set it someone else may have. If you can't find it then you may have to follow the steps here:
    Forgot passcode for your iPhone, iPad, or iPod touch, or ...
    Do you have a backup which might not have this restriction passcode? If so restore to that backup?

  • Itunes now requesting PW for old purchases. Current PW does not work. How to fix and gain access to songs purchased 6 years ago. Other, more recent songs all OK.

    Itunes now requesting PW for old purchases. Current PW does not work. How to fix and gain access to songs purchased 6 years ago. Other, more recent songs all OK.

    If you bought the music with another itunes account, then you will have to authorize the computer for that account.

Maybe you are looking for

  • Noted item

    hi, can get clarification on this. 1) by looking at this statement, it says no noted item for vendor, right? what about tcode f-57? 2) down payment request is for customer ONLY, right? "The down payment to a vendor is a real posting and thus cannot i

  • Is there any module in XI called XI admin

    Is there any module in XI called XI admin if yes then what does it comprise of

  • Why is my video cropped?

    The video I'm trying to edit is already cropped in the preview window. It's like the aspect ratio is off, but when I adjust those settings I just see zoomed-in/out versions of the aspect. When I play the video on Cyberlink, it looks fine, but in Prim

  • Armenian Firmware for Nokia 5800

    Can anyone help me , how I can make Armenian resource files .r38 for my Nokia 5800 Is there  Armenian Firmware for Nokia 5800 ?????

  • Project open error.

    Whan I open a ADF base web project from jdev 10.1.3.3 IDE fallowing error occurs. How can I solve this error. Thanks. oracle.jbo.dt.objects.JboException: Entity Attribute for this View Attribute cannot be found. model.EntObjDepartman.DepartmanAdi Mod