Access Restrictions - Blocked Applications does not save

Under the Access Restrictions section it is possible to Block Applications.
I enter a name for the application, the port range (from and to) and whether it is TCP, UDP or both. I then hit ADD which adds the application to the list of Blocked Applications in the box above. I then scroll down thru that box to find the App and [>>] add it to the Blocked List. I then hit SAVE SETTINGS
Upon returning to the policy and the Blocked Apps list the record I just created is nowhere to be found. Not in the Blocked List or under Applications.
What gives ???

Wireless-N Gigabit Router
Model: WRT310N
Firmware Version: v1.0.06
All PCs run VISTA
I don't see how a HARD RESET and POWER RECYCLE creates a fix for this. All that does is reboot the existing firmware and causes me to have to reenter all the router and security settings. The documentation for the lastest firmware (version Ver.1.0.9 build 4 12/11/2009) and the previous upgrade (1.0.07 build 14) does not include references to a fix for this problem. Has this been identified before and what firmware version is the fix included in ?
I have held off performing the 1.0.9 firmware upgrade as I have no confidence that this will fix this problem.

Similar Messages

Access Restriction on EA3500 does not work.

I tested this with my laptop by setting its access restriction/parental control to always not access the internet. But still my laptop can still search through wikipedia. Is this because of the router firmware? By the way I'm using the latest Connect cloud firmware. Thanks in advance.

I believe parental control is not really busted, it's just designed to work only with ipv4. What you can try though is to try the following:
Make sure that the laptop is only wirelessly connected to the router, because if the laptop was connected both wired and wireless then parental controls will not work since the laptop will be using two adapters.
Remove the entry under target devices, disable parental controls and save the settings.
Enable parental controls, add a target device, save the settings
Try to check if you can access wikipedia or other website because if parental control was working then it should add for a password
Try also to check the router's status tab if there's an ipv6 ip address because if there is, then parental controls will not work

HT1941 Hi i have recently updated my version of iTunes in order to sync music from my macbook air to my new ipod shuffle. After a successful installation the application does not launch and I am unable to oepn iTunes of access my music! Someone please hel

Hi,
I have recently updated my iTunes to the latest version in order to sync music onto my new ipod shuffle. However after a successful installation the application does not launch or open? There are no error messages. The application is just unresponsive.
I have already checked the compatibility with Safari, my operating system and checked my firewall is not blocking it - all is fine.
Does anyone have any other resolutions?
Many thanks

Hi Carolyn,
Thank you for your time and response. The trouble is I am unable to launch iTunes? I have restarted my macbook air a number of times to try and initiate the application but the issue persists and the application remains unresponsive. Will not launch?
Thanks

Javascript not working with 'Display as Text (does not saves state)'

Hi,
We have these following items in P3 of our application,
P3_EDIT_ACCOUNT Display as Text (saves state)
P3_USEFUL_LINKS Display as Text (saves state)
P3_LAST_APPROVED Display as Text (saves state)
P3_ARCHIVES Display as Text (saves state)
And we are initializing these items in a pl/sql process under 'Page Rendering'
For example,
:P3_ARCHIVES := '<font face="Arial, Helvetica, sans-serif" size="-1">Archives</font></a><td> ';
When our environment was upgraded from HTMLDB1.5 to HTMLDB2.0,
instead of displaying the proper value of :P3_ARCHIVES,
it was displaying the tags,
i.e. instead of displaying 'Archives', it was displaying the whole
'<font face="Arial, Helvetica, sans-serif" size="-1">Archives</font></a><td> '
So, when we changed all items to 'Display as Text (does not saves state)' and it was working.
But then we have another problem,
We render the rest of the same page with another pl/sql block,
Here is a portion from that pl/sql for your reference,
htp.p('
<script>
//Script to check the status change.
//The script source is rendered through PL/SQL.
function checkStatus()
var promptStr = someString;
if(ans.toUpperCase() == "AMBER" || ans.toUpperCase() == "RED")
          var cnfm = confirm(promptStr);
          if(cnfm)
          do something....
</script>
htp.print('
<td width="5%" bgcolor="#ebebc5" height="19" align="middle" >
<input TYPE="radio" name="'||l_g_fnumber||'" value="GREEN"');
IF l_allow_update THEN
     htp.print(' onClick="checkStatus()"');
ELSE
htp.print(' disabled onmousedown="return false;"');
                    do something....
Now the issue is , when we changed all items to 'Display as Text (does not saves state)', the checkStatus() function is not getting called in the onClick
event of the radio button and hence the confirm window for the call to
confirm(promptStr) is not coming up.
But if we revert back the items to 'Display as Text (saves state)',
the checkStatus() javascript function is getting called properly but html tags are displayed against the items instead of the proper value (as mentioned in ********)
Please do let us know a possible solution to this issue.
Thanks & Regards-
Rupak

Thanks Varad for your response.
This is the error i am getting.
1 error has occurred
PLSQL anonymous block source type can be used ONLY with Display Text (based on PLSQL) item type.
yes i am using in the source..
I also tried with the PL/SQL Expression of FUNCTION in this case it is executing the query but once i run the page ora- 06550 error occured.
Thanks
AT
Edited by: ranu on Jan 8, 2009 2:51 PM

Mac does not save settings.

Hi, I'm new here (I haven't got my mac for a long time either), so please bear with me!
I have a problem with many programs, namely my mac does not save the settings.
Word: The change of default Czech language into Polish is not permanent. Czech comes back after the restart.
Ableton: The authorisation of the program is withdrawn when I switch the laptop. I have to authorise it again after every restart.
Cubase: It changes audio input and audio output back to internal speakers and microphone after the restart.
Additionally, for example, I have changed the preferences of video files. I have changed the default player from QuickTime to VLC. Restart undoes the changes.
Has anyone have a similar problem?
Thank you in advance for your reply.

Back up all data. Don't continue unless you're sure you can restore from a backup, even if you're unable to log in.
This procedure will unlock all your user files (not system files) and reset their ownership and access-control lists to the default. If you've set special values for those attributes on any of your files, they will be reverted. In that case, either stop here, or be prepared to recreate the settings if necessary. Do so only after verifying that those settings didn't cause the problem. If none of this is meaningful to you, you don't need to worry about it.
Step 1
If you have more than one user account, and the one in question is not an administrator account, then temporarily promote it to administrator status in the Users & Groups preference pane. To do that, unlock the preference pane using the credentials of an administrator, check the box marked Allow user to administer this computer, then reboot. You can demote the problem account back to standard status when this step has been completed.
Triple-click the following line on this page to select it. Copy the selected text to the Clipboard (command-C):
{ sudo chflags -R nouchg,nouappnd ~ $TMPDIR.. ; sudo chown -R $UID:staff ~ $_ ; sudo chmod -R u+rwX ~ $_ ; chmod -R -N ~ $_ ; } 2> /dev/null
Launch the Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Paste into the Terminal window (command-V). You'll be prompted for your login password. Nothing will be displayed when you type it. You may get a one-time warning to be careful. If you don’t have a login password, you’ll need to set one before you can run the command. If you see a message that your username "is not in the sudoers file," then you're not logged in as an administrator.
The command will take a noticeable amount of time to run. Wait for a new line ending in a dollar sign (“$”) to appear, then quit Terminal.
Step 2 (optional)
Take this step only if you have trouble with Step 1 or if it doesn't solve the problem.
Boot into Recovery. When the OS X Utilities screen appears, select
Utilities ▹ Terminal
from the menu bar. A Terminal window will open.
In the Terminal window, type this:
res
Press the tab key. The partial command you typed will automatically be completed to this:
resetpassword
Press return. A Reset Password window will open. You’re not going to reset a password.
Select your boot volume ("Macintosh HD," unless you gave it a different name) if not already selected.
Select your username from the menu labeled Select the user account if not already selected.
Under Reset Home Directory Permissions and ACLs, click the Reset button.
Select
 ▹ Restart
from the menu bar.

Access DB (& .ldb file) does not close after crystal reports

Post Author: mgold
CA Forum: Crystal Reports
Access DB (& .ldb file) does not close after crystal reports
Hi! We have a VB application using Crystal Reports 6 that has worked successfully on hundreds of systems for over 10 years. Now, on one network, the application and access database does not close. It seems to hang on the [.Close] command.
When we open the application an peruse the screens without opening up a report (using crystal reports), the application and access db closes fine. But as soon as we run a report and then close the report and try to close the application, the access db does not close. Many of the screens open the db and grab data from the access db, but it's only after running crystal reports that we have this problem. (Please see more information below.)
Setup: Application and data (access 97 db) reside on a server in the same folder, but application shortcut is kicked off on client PC. Kicking off the shortcut on the client PC means that the image/process runs on the client PC (not on the server). In this problem case, the application shortcut is on a Windows XP Pro Version 2002 SP2 PC with the app & data on a Windows 2003 server. Users are local Admins on their PCs with "Full Control"over the directory and files on the server where the data (access 97 db) resides. This type of setup is typical and has worked without any problems for clients.
The application is written in Visual Basic, using Crystal Reports 6 (using DAO). We close the recordset, set it to zero and then it hangs on closing the db (.Close command).
A few key pieces of information:
- The application closes fine if the app & data (access 97 db) are on a local PC. This includes closing fine if the application is run directly on the Windows 2003 server where the data is stored.
- It worked on this client's network until sometime in the last few weeks.
- One thing that changed is that the company is using VMWare on its servers. Not sure if they started using VMWare at the same time as it started failing. This may be unrelated. Possibly other things changed, but can't get any more information ... yet.
- It works fine running the application from a Windows Vista PC with a user who is a domain admin.
- The access db and application hang for about 10-20 minutes and then eventually closes. It appears that somehow
Crystal Reports is keeping the db open, but I'm not sure why.The application doesn't quit and the database doesn't close even if I try to end the task with the Task Manager.
- The Crystl32.ocx version being used is 8.0.0.4 (if that matters).
- I copied 6 month old program files and database files to a test folder on the Windows 2003 server. It fails using these files that worked fine 6 months ago.
Any ideas or help would be greatly appreciated! If you know of another good place to post this, please let me know.
Thanks!
- Mark

Crystal doesn't support tables in HTML interpretation.
You can probably work your way around this by doing Replace() calls on the relevant tags.
See:
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/com.sap.km.cm.docs/oss_notes_boj/sdn_oss_boj_erq/sap(bD1lbiZjPTAwMQ==)/bc/bsp/spn/scn_bosap/notes%7B6163636573733d36393736354636443646363436353344333933393338323636393736354637333631373036453646373436353733354636453735364436323635373233443330333033303331333233313337333033383334%7D.do
The supported HTML tags are:
" html
" body
" div (causes a paragraph break)
" tr (causes only a paragraph break; does not
preserve column structure of a table)
" span
" font
" p (causes a paragraph break)
" br (causes a paragraph break)
" h1 (causes a paragraph break, makes the font bold
& twice default size)
" h2 (causes a paragraph break, makes the font bold
& 1.5 times default size)
" h3 (causes a paragraph break, makes the font bold
& 9/8 default size)
" h4 (causes a paragraph break, makes the font bold)
" h5 (causes a paragraph break, makes the font bold
& 5/6 default size)
" h6 (causes a paragraph break, makes the font bold
& 5/8 default size)
" center
" big (increases font size by 2 points)
" small (decreases font size by 2 points if it's 8
points or larger)
" b
" i
" s
" strike
" u
The supported HTML attributes are:
" align
" face
" size
" color
" style
" font-family
" font-size
" font-style
" font-weight

WHEN I GO TO PRIVACY SETTINGS AND CLICK ON EXCEPTIONS AND TYPE IN A WEB ADDRESS TO ALLOW ALL THE TIME IT DOES NOT SAVE IT THE NEXT TIME I SIGN ON TO FIRE FOX IT IS LOST. IT WORKS FINE ON MY DESKTOP BUT NOT ON MY LAPTOP THAT I JUST BOUGHT in English.

Question
WHEN I GO TO PRIVACY SETTINGS AND CLICK ON EXCEPTIONS AND TYPE IN A WEB ADDRESS TO ALLOW ALL THE TIME IT DOES NOT SAVE IT THE NEXT TIME I SIGN ON TO FIRE FOX IT IS LOST. IT WORKS FINE ON MY DESKTOP BUT NOT ON MY LAPTOP THAT I JUST BOUGHT in English.

I just updated my whatsapp...clicked on whatsapp in appstore and now can access my whatsapp

View Object Editor in JHS 10.1.2 does not save any changes....

Hi,
When I did exactly as the JHeadstart Tutorial says, I noticed that
in JHeadstart 10.1.2 with JDeveloper 10.1.2
JHeadstart does not save any changes I make in the View Object Editor
of the Application Structure File Editor !!!
For instance when I change the Width property of an Attribute from 60 to 5
it changes to 5, but when close the View Object Editor
and reopen it again, the Width is back to 60...
Even when I click the button "Validate the Application Structure File" before
closing the VO Editor....
What do I do ??? Is the only solution to edit the XML file
or something like that without using the VO Editor ?
Or is there a better solution ?
Does it maybe work in an older version of JHeadstart ?
If so, where is the older version available for download ?
Thanks,
Eric Joosse

Eric,
How did you leave the JHeadstart VO editor?
The changes should be saved when you click the OK button in the VO editor itself, but they are not saved if you click Cancel, or the little cross in the upper right corner, or leave it open while going back to the Application Structure File editor. That's because it's a standalone editor (you can also find it when right-mouse-clicking the VO in the Model project). The icon in the Application Structure File editor is just a quick way to get to it.
Hope this helps,
Sandra Muller
JHeadstart Team
Oracle Consulting

Display As Text (Does Not Save State) Render Behaviour

I suppose this is directed more at the Oracle team members (as most of my posts are...) than anyone else, but others might find this interesting.
It would seem when an item has a type of "Display As Text (Does Not Save State)" the item's value is output as pure text which shows up as text nodes under the TD cell. However if there is anything in the "HTML Form Element Attribute" text field on the "Edit Page Item" page, the APEX rendering engine will output a span tag with those attributes around the value of the item. If the attribute is left null, no span tag is output.
Further more, the span tag does not have an ID attribute. One can also not set the "HTML Form Element" text box to contain the text 'id="" ' as APEX will throw an error stating that you can not specify the id attribute. So if someone would happen to want to access/change the value via JavaScript (say after an Ajax request of a hidden id change), it requires a hack (setting the TD cell's ID to the page item's name), DOM inspecting/sniffing, outputting an ugly disabled text element, altering the flows user's tables, or altering the render cache.
Is there any reason, why this span tag is not always output with the ID attribute set?

Hello Andrew,
You are, of course, correct. The APEX engine does not use the item ID for the "Display as Text (does not save state)". However, if you need to manipulate the item, using JS, you can use the "Display as Text (save state)", which does use the item ID. The on-screen effect is the same, but the JS use is easier.
Your original question though, remains open.
Regards,
Arie.

DISPLAY AS TEXT (DOES NOT SAVE STATE)

can i use the pl/sql anonymous block or pl/sql function body for item which is DISPLAY AS TEXT (DOES NOT SAVE STATE). I am using this query and getting an error in case of pl/sql anonymous block can be used only for save state item. my apex version is 2.2.1.00.04.
my query is
declare
vCNT number;
v_exception_detail varchar2(200);
BEGIN
SELECT COUNT(*)
INTO vCNT
FROM table a
WHERE a.col1 IN
(SELECT DISTINCT x.col1
FROM table1 x)
AND a.col2 = TRIM(:P21_col2);
IF vCNT > 1 THEN
IF NVL(&P21_col2, -1) <> -1 THEN
SELECT DISTINCT SR.col3
INTO v_exception_detail
FROM table1 SR
WHERE SR.col1 IN
(SELECT col1
FROM table
WHERE col2 = TRIM(:P21_col2)
AND col4 = :P21_col4);
ELSE
v_exception_detail := NULL;
END IF;
ELSE
SELECT DISTINCT SR.col3
INTO v_exception_detail
FROM table1 SR
WHERE SR.col1 IN
(SELECT col1
FROM table
WHERE col2 = TRIM(:P21_col2));
END IF;
--DBMS_OUTPUT.PUT_LINE(v_exception_detail);
RETURN v_exception_detail;
END;
Could any one suggest how i can execute this code in case of item of DISPLAY AS TEXT (DOES NOT SAVE STATE).
Thanks,
AT

Thanks Varad for your response.
This is the error i am getting.
1 error has occurred
PLSQL anonymous block source type can be used ONLY with Display Text (based on PLSQL) item type.
yes i am using in the source..
I also tried with the PL/SQL Expression of FUNCTION in this case it is executing the query but once i run the page ora- 06550 error occured.
Thanks
AT
Edited by: ranu on Jan 8, 2009 2:51 PM

My Fire Fox does not save my History

My Fire Fox 3.6.6 Does not save my History
After 3 days my History does update and places.sqlite after reaching 1000 KB it does not save important links
== User Agent ==
Mozilla/4.0 (compatible; MSIE 7.0; Windows NT 5.1; (R1 1.5))

Firefox now always stores the old session, and you can access it by going to the History menu and selecting "Restore Previous Session"
If you want Firefox to display the message to save the session, it can be turned back on by changing some preferences.
# Type '''about:config''' into the location bar and press enter
# Accept the warning message that appears, you will be taken to a list of preferences
# Locate the preference '''browser.tabs.warnOnClose''', if its value is set to '''false''', double-click on it to change its value to '''true'''
# Repeat this for these 3 preferences '''browser.warnOnQuit''', '''browser.warnOnRestart''' and '''browser.showQuitWarning'''
If you always open the last set of tabs, an alternative approach is this:
# Click the orange Firefox button, then select options to open the options window
# Go to the General panel
# Change the setting "When Firefox starts" to "Show my windows and tabs from last time"

Safari 7.02 does not save my preference or view changes

Safari 7.02 does not save my preference or view changes

Triple-click anywhere in the line below on this page to select it:
~/Library/Preferences/com.apple.Safari.plist
Right-click or control-click the highlighted line and select
Services ▹ Show Info in Finder (or just Show Info)
from the contextual menu.* An Info dialog should open.
Does the dialog show "You can read and write" in the Sharing & Permissions section?
In the General section, is the box labeled Locked checked?
What is the Modified date?
If you don't have read and write access to the item, change the settings as directed here. Note, however, that if one file has wrong access settings, most likely others do as well. If the item is locked, unlock it.
*If you don't see the contextual menu item, copy the selected text to the Clipboard by pressing the key combination command-C. Open a TextEdit window and paste into it (command-V). Select the line you just pasted and continue as above.

My MacBook Pro does not save bettery life.i use 4 hrs for the full charge better instead of 7 hrs.what is the problem.Please help.

My MacBook Pro does not save bettery.I use 100% bettery charge 3-4 hrs instead of 7 hrs.what could be the problem?

7 hours mentioned is possible when run under lab conditions.
Running GPU intensive applications will decrease battery runtime.
Maximize Runtime / Tips for maximizing your battery charge
http://support.apple.com/kb/HT1446
Runawy applications can shorten battery runtime,affect performances and
increase heat and fan activity.
http://support.apple.com/kb/TS1473

TS3274 Camera does not save photos to picture roll

I snap pictures and shoot video but it does not save to "Photos" camera roll. This is a newly restored IPAD since I broke the screen on my old one. Everything worked as expected on old one. I have everything "on" under privacy.

If you are sure that all privacy settings are correct including anything in Photos in restrictions, did you try quitting the camera app and rebooting the iPad?
Go to the home screen first by tapping the home button. Double tap the home button and the task bar will appear with all of your recent/open apps displayed at the bottom. Tap and hold down on any app icon until it begins to wiggle. Tap the minus sign in the upper left corner of the app that you want to close. Tap the home button or anywhere above the task bar.
Reboot the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons.

Delivery block 01 does not allow requirements

Hi,
I am doing assembly processing for creation of Projects through sales order,
selected the following requirement class 212-PS04
requirement types- KMPN-212.
Now when i am creating Sales Order and saving,it is not creating any projects,
and is giving following error
"Delivery block 01 does not allow requirements"
also i have created standard WBS and Network and assignment material to it.
Please help.
Thanks,
Nitin

hi
please check in the sales order header whether delivery block indicator is set "01"
if so remove and save.

Access Restrictions - Blocked Applications does not save

Similar Messages

Maybe you are looking for