Access Server 2511 can't access Routers & Switch

Hi,
i recently bought Cisco Routers, Switch, Access Server and Frame-relay for my CCNP home lab, but problem is that my Access Server 2511 can't connect to any other devices like router or switch, i have configure "loopback 200.1.1.1" than setup "ip host Router1 2001 200.1.1.1" command for all of my other devices, when i try to connect to other devices it give me this message but do not show prompt for that device...
(Router#f2
Translating "f2"
Trying f2 (200.1.1.1, 2001)... Open)
i leave this message for a long time but Prompt never come....
i also use CLEAR line command to clear but problem still exist.
Please help me to resolve this problem...
Regards,
ABDUL

Hi
Thank you for your guidance, i have done changes which you were suggested, but problem still exit ..this is my fifth day battling with this issue..i can connect and work on all devices through network using # telnet (ip address of any device) ..i am using the right cable (72-0845-01) Cisco Cab-Octal-Async 8 Lead Octal Cable (68 pin to 8 Male RJ-45s)... now i am thinking that there is a problem with cable or Access Server 2511 physically not with configuration..any way i am waiting for your reply...
tserver#sh run
Building configuration...
Current configuration : 1054 bytes
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname tserver
boot-start-marker
boot-end-marker
enable secret 5 $1$sWZ2$iNhMYtvWsbwBSGLnYtphr/
enable password cisco
no aaa new-model
ip subnet-zero
no ip domain lookup
ip host f1 2001 172.168.1.1
ip host s1 2002 172.168.1.1
ip host r1 2007 172.168.1.1
ip host f2 2009 172.168.1.1
ip host s2 2010 172.168.1.1
ip host r2 2016 172.168.1.1
interface Loopback0
ip address 172.168.1.1 255.255.255.0
interface Ethernet0
no ip address
shutdown
interface Serial0
no ip address
shutdown
no fair-queue
interface Serial1
no ip address
shutdown
ip http server
ip classless
dialer-list 1 protocol ip permit
line con 0
password cisco
login
transport output telnet
telnet speed 9600 38400
line 1 16
transport input telnet
transport output telnet
flowcontrol hardware
line aux 0
line vty 0 4
password cisco
login
transport input telnet
transport output telnet
telnet speed 9600 38400
end

Similar Messages

After install Crystal Report Server 2011, can not access control tools

Afte install Crystal Report Server 2011, can not access control tools from web or from application.
My server OS is Windows 2008 R2 SP1. I follow the default setting. How to fix it?
Error message is above.

Is Tomcat started? On your Start menu you should have an option to get to "Tomcat Configuration" or, under the CRS menu you can run the "Central Configuration Manager" to start Tomcat.
What URL are you using to connect to the web app? By default Tomcat runs on port 8080 so your URL should look something like this: "http://<servername>:8080/BOE/CMC" or "http://<servername>:8080/BOE/BI".
If Tomcat is running and you're trying to access it from another computer, check to see if the Windows Firewall is turned on for the server - if it is, turn it off for "Domain" access.
If Tomcat won't start, go to the folder where Tomcat is installed and then look in the "logs" folder. There should be a file called "stderr.log" which you can open in Notepad to see what types of errors might be occurring (you can ignore any errors having to do with "persisted sessions".) If there are other errors, post in the BI Platform space to get assistance.
-Dell

After install Crystal Report Server 2011, can not access control tool

After install Crystal Report Server 2011, can not access cntrol tool from web or from application. My server OS is Windows 2008 R2 SP1. I follow the fedault setting. How to fix it?
Error message:

Seems like webapps are corrupted, Just redeploy the webapps.
refer the below thread to do the same.
http://scn.sap.com/thread/3400477

Need help with setting up a photolibrary on server that can be accessed/edited by multiple users

Hi:
I would like to develop an in-house photolibrary for our graphics department. The goal is to be able to add keywords to all our images so that we could have a more dynamic means of searching through our countless scanned images. Lightroom works great with regards to keywording and searching.
To make it so all the computers in our office could have access to the images, I created a photolibrary on our server that can be accessed by any of the computers in our graphics dept. However, when one computer adds keywords to an image, that info does not show up on any of the other computers. Perhaps this is an issue with the trial version and we need to get the license? A few other people suggested that it might have something to do with my export settings - I tried to play around with the settings but had little luck...Any Advise?
Thanks,
Leo

Thanks for your thorough reply. Is there a way to have one MASTER computer that could create the keywords and have the other computers access the master computer's catlogues - or something of that sort. We are small graphics dept. with three people so even that would suffice.
Lightroom is not a networked application, and cannot be set up so that multiple computers can access LR via a network.
The only real workaround with LR is to put the catalog and photos on an external HD and then physically connect the external HD to the computer of the person wanting to use it. So only one person can use the catalog at one time.
You can look up Digital Asset Management (DAM) software on Google if you really need to have multi-user access and networked.

Website appears on server, but can't access from other computers

I migrated from Server 10.5 to Snow Leopard Server. Used the migration tool to bring everything over from the previous box.
I can access the website via browser from the server, but can't access it from any other computers. I'm a decidedly non-geek type, so too many settings are gibberish to me. However, I at least ran the previous server for many years without problems.
Any clues as to what I'm missing?

What error message(s) are you getting from the remote web browser clients?
Exactly what string are you typing into the address bar of the web browser?
Are the remote clients on the same LAN as the web server, or on a remote network?
If running, is the firewall open for port 80 or port 443 for the web server?
Knowing a little more "gibberish" helps when you're running a server, too.

I need help installing Acrobat Reader - messaged failed to connect to a DDE Server. Can't access documents

I need help installing Acrobat Reader - messaged failed to connect to a DDE Server. Can't access documents

Please see if "acrobat failed to connect to dde server" when openning Adobe Acrobat XI PRo helps.

I can not access the switch through the console (solved)

Hello,
I'm having a problem.
I can not access the switch through the console. The web interface is working properly.
Model: SRW224g4
Below some pictures.
The HyperTerminal settings
error:
If anyone can help me?
Thank you and excuse the bad English.

Hello Rumenigue,
It looks to me like you are using a console cable. The reason you usually see them the other way around is because with a console cable the RJ-45 end goes into the device (an ethernet jack labeled console) whereas on this switch the console port is serial itself.
Usually the serial end of the cable you have plugs into a USB to serial adapter (because most computers today don't have serial ports anymore) and that USB connection goes into your PC, creating the virtual COM port you need in HyperTerminal.
So if you get a USB to Serial adapter you could plug that from USB to the console port, or if you computer has a serial port of its own just connect a serial cable directly from the PC to the switch, then use HyperTerminal with the settings recommended above by Tom.
Hope I have helped,
Christopher Ebert
Network Support Engineer - Cisco Small Business Support Center

Connection of LC/APC fiber patch cords to Cisco Catalyst 6500 $ Cisco Access 3750 Switches

I have an LC/APC fiber patch cord infrastructure and I want to connect it to Cisco Catalyst 6500 & Cisco Access 3750 Switches. what type of transceiver should be used?
I read a note on Cisco website stating the following for Cisco SFP+ transceivers:
Note: "Only connections with patch cords with PC or UPC connectors are supported. Patch cords with APC connectors are not supported. All cables and cable assemblies used must be compliant with the standards specified in the standards section"

Thank you, but my question is that I have a single mode fiber patch cord with LC/APC connector while cisco stating a note that only use LC/PC or LC/UPC type of connectors with SFP+ transceiver.
So what type of transceiver should I use to connect LC/APC patch cord to cisco switches? Is there another type or SFP+ still can be used?

MSTP on Access Layer Switches

Hello everyone,
When configuring MST for STP, is there a need to configure it on access layer switches in a collapsed core design? I can find docs to configure the root and secondary root bridges but I don't see anything about configuring access layer switches. In RSTP, you configure it on all switches cooperating in STP and set the root and secondary bridges accordingly. Any help is appreciated.
Regards,
Terence

Hi,
You should configure your access switches for MST as well so you are using the same STP for core and access. The only difference between the core and access is that the core is root and back up root for STP and the access layer is just default (32768).
HTH

Lost access to switch after upgrade to metro access image

Hello
After an upgrade of a 3400 ME switch image to metro access one (340x), the switch was reloaded. After that, the only way to access the switch is the console port. I am beginner with cisco switches but I managed to configure the switch to make an upgrade through TFTP. Now I want to configure port 0/1 on vlan access mode to vlan 1. Any help on this is more than welcome. Thank you.
Switch Ports Model SW Version SW Image
* 1 26 ME-3400-24TS-D 12.2(35)SE3 ME340x-METROACCESS-M
no aaa new-model
system mtu routing 1500
ip subnet-zero
no file verify auto
spanning-tree mode rapid-pvst
spanning-tree extend system-id
vlan internal allocation policy ascending
vlan 10
name management
interface FastEthernet0/1
speed 100
duplex full
interface FastEthernet0/2
shutdown
interface FastEthernet0/3
no switchport
no ip address
no ip route-cache
shutdown
interface FastEthernet0/4
shutdown
--More--
interface GigabitEthernet0/2
port-type nni
interface Vlan1
ip address 192.168.1.252 255.255.255.0
no ip route-cache
interface Vlan10
no ip address
no ip route-cache
shutdown
ip default-gateway 192.168.1.1
no ip http server
cisco3400#sh int fastEthernet 0/1 switchport
Name: Fa0/1
Switchport: Enabled
Administrative Mode: static access
Operational Mode: static access
Administrative Trunking Encapsulation: dot1q
Operational Trunking Encapsulation: native
Negotiation of Trunking: Off
Access Mode VLAN: 1 (default)
Trunking Native Mode VLAN: 1 (default)
Administrative Native VLAN tagging: enabled
Administrative private-vlan host-association: none
Administrative private-vlan mapping: none
Administrative private-vlan trunk native VLAN: none
Administrative private-vlan trunk Native VLAN tagging: enabled
Administrative private-vlan trunk encapsulation: dot1q
Administrative private-vlan trunk normal VLANs: none
Administrative private-vlan trunk private VLANs: none
Operational private-vlan: none
Trunking VLANs Enabled: ALL
Capture Mode Disabled
Capture VLANs Allowed: ALL

I found the source of the problem. My switch was connected to another one. I had to explicitly put port type to nni.
Hope it helps someone.

Packets dropped to Access layer switch???

We have a 6509 running in Native IOS that has 2gb port channels connecting to our 7 access layer switches. About a week ago we were working with Remote span vlans and added a remote span from the 6509 to our other core (6513) which is connected via a 20Gbps portchannel. We began to notice that a lot of people were calling in reporting devices as being slow and we noticed that from the 6509 (Which was the root bridge) we were disgarding millions of packets on the transmit side of our access layer switches. We took out the remote span but it appears that we are still disgarding packets. There are no input or output errors on either side. The Remote span VLAN does not exist on the access layer switch's VLAN database. Does anybody have any idea what we should be looking for?

you can use an acl to match the number of packets that come into / out of each of the devices. Simply use two lines in each acl where on the first line you match the packet in question and on the second line you have "permit ip any any" so you don't block any packets. Then simply apply the acl either inbound or outbound on the interface in question. If you want more than one acl on a given device, such as inbound one interfaceand outbound another, be sure to use two different acl numbers.
create the acl's and apply them
ensure there isn't an active call
clear access-list counters on all devices where you configured the acl's so we ensure all of them are set to 0

Can Cisco Routers, Switches, or Firewalls run AV?

Can anyone point me to a document or official statement from Cisco stating that their routers, switches, and firewalls are not capable of running Anti-Virus/Anti-Malware to protect their IOS? NERC CIP standards require that all devices contained within the Electronic Security Perimeter run Anti-Virus/Anti-Malware software "where technically feasible", if the devices cannot run AV/AM you have to submit a "Technical Feasibility Exception"....done that...now they want proof that Cisco devices (routers, switches, firewalls) are not capable of running AV/AM to protect their IOS. Please don't confuse this with all of the offering that Cisco has to protect end-user devices...this applies only to the routers, switches, and firewalls.
Any answers would be greatly appreciated, even comments from others dealing with this issue.

A couple of years ago in a conference there was a presentation that claimed to install a rootkit to Cisco IOS devices.
Here is the response from Cisco http://www.cisco.com/warp/public/707/cisco-sr-20080516-rootkits.shtml
That is the closest I can think of that could help you.
PK

How can i upgrade system IOS images of routers, switches and firewalls

Hi,
I am very much surprised and less of understanding yet how Cisco's licensing program or IOS upgrades are done. I have many routers, switches & ASA's of whom i wan to upgrade the IOS's but i cannot do so. How ever i can download those images from internet but i want to know how can i do this from Cisco as i don't want to trust those IOS's available over internet.
As per my study what i have found that i need to have Cisco Service Contract number for that devices so that i can download updated IOS Images for them.
Someone kindly explain what are the best methods for the above requirements.
Regards
@Mohammed

You're correct regarding a service contract. Cisco calls this Smartnet support. It includes both hardware support (i.e. returns for failed hardware), software support (including right to download and upgrade your software) and technical assistance (via the Cisco TAC). Smartnet is charged separately for each covered device. Once you have it, your cisco.com userid needs to be associated with your service contract number. Doing that will then allow you to download the software from cisco.com. (There are some very limited cases in which you don't have to have a support contract - mostly when there is a security advisory (PSIRT) indicating the Cisco software was flawed as it was initially released.)
Every product (or product family) has a product support page on cisco.com. That page includes release notes, configuration guide, users guides, and a link to software downloads for that product. Start by reading the release notes and determining which (if any) upgrade is appropriate for your product. Then you can download and upgrade the software as necessary.

Server wont communicate with new network switch.

Hi, I hope someone can help.
I have a small office network running Macs with OS 10.6.4, HPs with Windows XP, and a mac mini server running 10.6.4 server, file sharing only.
DHCP and internet access etc is controlled by a Netgear ADSL router. All machines are connected by a 16 port 10/100 Netgear switch.
The problem is I replaced the switch with a 10/100/1000 switch and all machines connect fine except the server. This will not connect at all with the new switch, not even do any lights come on. However if I connect the server to the old 10/100 switch then to the new gigabit switch it connects fine but this defeats the purpose of the gigabit access to the server and the high speed macs on the network. The reason I upgraded in the first place! The standard Macs are Imac G5 Intel based late Snow leopard models and they have no trouble with the new switch.
Does Snow Leopard server somehow remember specific hardware on the network when setup? And needs to be changed to recognize the new?? I tried switching everything off and restarting the whole network.
I don't have a heap of knowledge but thought this should have been simple.
Any help would be greatly appreciated.
Cheers, paul

Thanks for the reply.
No it is not managed, No uplink port, uplink is auto controlled on any port.
I have swapped and swapped and swapped this is what led me to using the old switch on the server.
This is what happens.
Putting the server cable from the server into the new gigabit switch Tried with 300m cable directly next to it. No connection on any of the 16 ports. tried several cables including longer ones etc.
Now if I use the same cable from the gigabit switch to any port on the old switch then connect a cable from any other port of the old switch to the server. Connection, no problems at all. I.E the Old switch is uplinking to the new.
It is as if the server says "hey where is the old switch I can't work without it" Thats why I thought maybe OS X server kept some sort of register of the devices when it is initially setup and this may need to be changed.
Also any other computer works fine when placed at the same access point as the server including the Standard Snow leopard Macs.
I am thinking maybe to reinstall the server OS to see what happens?
Was supposed to be a simple job. Both switches are physically exactly the same. Pull a cable out of port 1 and stick it in port 1 of the new switch etc plug it in and turn it on????

Terminal server 2511

hello folks i am new to cisco i have 14 cisco routers some 2500,2600,3600,switches,1900,2900,3500,i have read the setup for telnetting with the 2511 can telnet to most but not to all,i am using both asyn lines any reason why i cant connect to all the units, thanks for you help in advance.

here is an outerminal_server#sh run
Building configuration...
Current configuration : 1167 bytes
version 12.2
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname terminal_server
enable secret xxx
ip subnet-zero
no ip domain lookup
ip host sw2924b 2002 192.168.0.211
ip host sw2924c 2003 192.168.0.211
ip host r4 2004 192.168.0.211
ip host r5 2005 192.168.0.211
ip host r13 2013 192.168.0.211
ip host r16 2016 192.168.0.211
ip host sw2924a 2001 192.168.0.211
ip host r6 2006 192.168.0.211
ip host r7 2007 192.168.0.211
ip host r8 2008 192.168.0.211
ip host r9 2009 192.168.0.211
ip host r10 2010 192.168.0.211
ip host r11 2011 192.168.0.211
ip host r12 2012 192.168.0.211
ip host r14 2014 192.168.0.211
ip host r15 2015 192.168.0.211
interface Loopback0
ip address 192.168.0.211 255.255.255.0
interface Ethernet0
no ip address
shutdown
interface Serial0
no ip address
shutdown
interface Serial1
no ip address
shutdown
ip classless
ip http server
banner incoming ^C
welcome to my terminal server do you have my password ^C
line con 0
line 1 16
flush-at-activation
transport input all
stopbits 1
line aux 0
line vty 0 4
login
end
terminal_server#tput of my config

Access Server 2511 can't access Routers & Switch

Similar Messages

Maybe you are looking for