Access Share - Wireless/USB Drive with KDE

I have an external hard drive connected to my wireless router by a USB port on the wireless router. Using Gnome I never have a problem conntecting to the external drive but I cannot do so in KDE. Browsing the network sees drive but when trying to connect just get the following message...
"The location 'smb:/' is invalid."
I just cannot figure out why I cannot connect in KDE. Help...thanks.

With only KDE I'm unsure how to do it, I use Subtle. But you can put a line in your /etc/fstab, to mount it. (https://wiki.archlinux.org/index.php/Sa … e_to_fstab). I'm assuming its samba.

Similar Messages

Can you share a hard drive with the current airport extreme

Hey all!
I read that you can share USB drives with the new airport extreme. Can you do that with the current ones?
Thanks,
B

Massi65, Welcome to the discussion area!
You really should start a new thread since your question is about the new square AEBS and the thread started with a question about the previous AEBS.
With either AEBS you could wirelessly gain access to a hard drive by one of these 3 methods:
Use a hard drive with wireless networking capabilities. The drive would connect to the wireless network like any other wireless client.
Use a hard drive with an Ethernet interface. Connect the drive to the AEBS's LAN port.
Connect a hard drive via FireWire or USB to another Mac and then share the drive from that Mac.
The new square AEBS offers a new possibility. You can connect a USB drive directly to the new AEBS and share it to devices connected to the AEBS's network.
What performance could I expect?
No one can answer this directly since no one has any of these devices to try.

MacBook Pro Retina hangs while opening mounted share or USB drive

I have a Macbook Pro Retina that I just updated to 10.8.2 over the past weekend. Now, when I try to open a mounted SMB share or USB drive, the system hangs completely! I had the system set to auto-reconnect my network shares, so when this started happening the system would hang right after login. I was able to get in with Safe Boot and disable the auto-connect, so at least I can work now, but not being able to use a flash drive is really getting on my nerves. Any ideas?

I just ran a few tests to confirm my suspicion that this is a sleep problem for me and found that my rMBP will restart as soon as it has entered the sleep cycle. Set it to auto sleep after 10 minutes and it will restart at 10 minutes, set it to sleep at 3 minutes and it will restart at 3 minutes. Command it to sleep and it will restart.
So for me at least there is a workaround and that is to set sleep to "never". The display still sleeps but my mac keeps running. So that's not a solution but it is a workaround, and if I want it to shutdown and not restart I either hold the powerbutton or take off the power cable and choose shut down from the dropdown menu (it won't restart on battery power, it'll just shut down).
I hope that helps someone else! And I hope it helps the engineers to diagnose and actually solve the very long running problem for us all..

Can I use a non apple wireless hard drive with time machine?

Can I use a non apple wireless hard drive with time Machine?

Some NAS (network storage) systems do claim to support Time Machine, with varying levels of success. For example, the Synology units have this feature. They're not officially supported by Apple, though.
Matt

Cannot mount external USB drive with FDisk_partition_scheme

Due to some recent mac issues in my lab, we updated one of the computers to Maverick 10.9.4 from Snow Leopard 10.6.8 yesterday. Anyhow, this seems to have erased the ability of the mac to read or mount several identical USB drives with the NTFS format (WD My Passport Ultra 500GB USB3.0). It could do it yesterday when it was OSX 10.6.8, but not today (OSX 10.9.4). The drives still work fine on other OSX 10.6.8, Windows 8.1 and Ubuntu 14.04 computers (this is appears to be a problem with the Maverick 10.9.4 operating system itself, rather than the flash drives which work flawlessly with every other computer I've tried). I want to remove data from the computer to create backups on the USB drives (no, I don't want to create an online backup or buy a new set of USB drives).
diskutil can see the drives, but cannot verify or repair them as they lack a GUID (GPT) partition scheme. I'm assuming this is the root of the problem. Manually mounting the drives does not work. Installing the ntfs-3g driver also did not work (I was using this to write to the NTFS drives until we upgraded OS's). Installing the WD Passport drivers for OSX also did not work. How do I get the mac to mount these drives?
I could reformat one USB drive and then copy to the others, but this would be extremely inconvenient and take days of copying files back and forth (and would prefer to fix the mac rather than go through this with every NTFS drive I own). If I did this, the FAT32 hard drive format would not be suitable, as format is unable to handle the extremely large sequencing datasets I need to transfer. I'm not super familiar with hard drive formats, but in the event we cannot get Maverick to actually work could someone possibly suggest a format able to handle large file sizes (the largest file I need to move is ~60GB) and be compatible with Windows 8.1 / OSX 10.9.4 / Ubuntu 14.04 as well?
Another workaround I thought of would be just to install an Ubuntu partition on the mac and get the files off through the Linux install. Which is also inconvenient, but would probably be faster than trying to reformat the drives and copy everything over onto them again given the amount of data I want to transfer.
Unrelated, but is there any way to view files and folders in the OSX root directory besides through Terminal? It seems like this functionality was also removed when we "upgraded" from Snow Leopard. (At this point, if it were up to me I would wipe all of the macs we own and replace them with Ubuntu... even the most minor of tasks always require some sort of workaround with them... at my wits end here ).

Yeah this definitely appears to be a problem specifically with this mac. It's been having all sorts of weird problems lately, and we figured that upgrading to Maverick might fix them (but instead we got new problems).
To give an update on this, I ended up reformatting one of the drives to HFS+ and disabled journaling. It now recognizes the drive again, and I'm pulling the files off that way. I looked at exFAT, but it looks like HFS+ has much better Linux support (Windows is read-only but that's only a minor annoyance, as the algorithms to process the data only run on UNIX machines anyways). It's a shame I couldn't keep using NTFS (had to copy over literally EVERYTHING again...) but whatever. Again, no solution for the issue (where this mac can't read NTFS drives).
@rkaufmann87 - To give a bit more explanation, we recently had to disable online backups because apparently the sheer amount of data causes Time Machine to freeze the computer and fail every time it has a scheduled backup (original issue we thought that upgrading to Maverick would solve... didn't work). The hard drive has been having a lot of issues when it begins to reach max capacity as well. So I am pulling off all of my files to external hard drives and deleting the local copy before we attempt to back up online again. And the data would probably take me a year and a lot of money to recreate (for the curious, it's high throughput sequencing data). I'm choosing not to take any chances as a result.

How do I share a hard drive with the new iMac to load a disk from macbook pro

How do I share a hard drive with the new iMac to load a disk from macbook pro. I want to install office for Mac from a disk but dont know how to share har drive from macpro
thanks

The new iMac's don' t have DVD drives however almost all have a disk drive. The easiest method of installing MS Office for Mac on your new iMac is to download it from Microsoft and then input the code you received when you purchased your original license. Otherwise you can use the DVD drive on your MBP to install on your iMac, that feature is called Remote Disc. Instructions for Remote Disc can be found at:http://support.apple.com/kb/ht5287

HT1948 USB drive with install image is showing in Startup Manager on a Mac Pro, but wont boot. Showing circle with cross strip, and shut down automatically. USB device are made and work on two different MacBook Pro, but used on Mac Pro. Any help?

USB drive with install image is showing in Startup Manager on a Mac Pro, but wont boot. Showing circle with cross strip, and shut down automatically. USB device are made and work on two different MacBook Pro, but used on Mac Pro. Any help?

OS X installers have always been fairly specific, hardware-wise. I haven't read anything reflecting that situation with the Recovery HD, so it may be that the Recovery HD created for the MacBook Pro does not have the necessary drivers for the Mac Pro. Obviously, nothing definitive here, but a possibility.

E1550 - unable to access USB drive with Ubuntu

I am probably overlooking something real obvious but after screwing around for two hours I figure I need some help.
I am running Ubuntu 14.04. I have set up the E1550 router with an external drive that I formatted with the router utility. At this point I do NOT have an internet connection hooked to the router - I am not sure I want to for now. What I would like to do is to be able to access, wirelessly, a drive that multiple users can use to back up their important files onto.
I have tried using anonymous disk read/write access as well as creating shares. All the features seem to be setting up ok but at this point I have no clue how to access the drive.
I have tried using the Ubuntu files utility and then selecting 'browse network' followed by selecting 'windows network'. Alas, 'windows network' is an empty file with no drive present.
I have tried accessing the router wirelessly and also hard wired - no joy.
Am I maybe not acessing the drive properly through Ubuntu? Do I need to mount the remote drive rather than accessing it through the windows network ?
Thanks in advance for any pointers given !
Solved!
Go to Solution.

I am not expert with Ubuntu OS but have you tried to map the drive on your computer? I have no idea how to do that using Ubuntu but if you're using Windows or Mac, you can simply follow the steps from Linksys KB. It usually helps me when I am trying to enable file-sharing capabilities within my network.

Cannot access shared external hard drive with other mac accounts

I cannot access a shared external hard drive with other mac accounts (all accounts are on the same macbook Pro). The shared external drive is shared via time capsule and is connected (of course) in USB. I see well this external hard drive as a shared disk with my main account. Yes shared option has been activated with the Airport Utility .. but when I open other account these othe accounts can see the external drive but cannot access to its content that is flagged with a no way sign. Strangely enough when I close my main account and start opening a new session with one of the other account then fine I can access the external hard drive and its content .. BUT then it is from my main account than I cannot access its content the no way sign showing ..
Looks like only one account at a time can access the content of this SHARED external hard drive .. any one as an idea on how to really make it a shared hard drive so that all accounts on the same mac can also access it ? I am at my wit ends on this case. THANKS ..

Results of my enquiries at Apple Genius Bar .. the guys found the problem interesting. They've been unable to provide a fix neither to give any explanation as to the reason why. To be fair I was not much impressed by the technical level demonstrated ..
In the mean time I have found that if account no.1 can see the shared external drive content and in such case account no.2 (same Mac computer) cannot see its content (only the external HD with a no way sign) this account no.2 can UNMOUNT (by ejecting) this external HD from account 1 and then remount it (just clicking on the TC shared part in a finder window) and .. see and access its content ; whilst account no.1 cannot see its content anylonger. Unless it unmounts the shared external HD and remount it .. then account no.2 can see its content anylonger. This can goes on an on.
So eventually YES the TC can allow to share a USB external drive between several accounts and a same Mac .. BUT this require to unmount and remount EACH time the external drive is accessed from a "no.2 account". So OK to share files with seldom access but not practical in case of frequent access needed.
I just I have now to figure how iTunes can automatically unmount and remount a shared external HD when it needs to access one of this shared HD content from on time account no.1 and then next time from account no.2. May be I am asking too much ..

X220 - Access Connections Wireless issue - Driver disconnected while associating

I am trying to connect to our wireless network at work. I have verified that my settings are correct with the other X220s that we have connecting to our network. When the connections fails and I select "help me fix this" I get four error messages.
Thanks in advance if anybody has any ideas.
Connection status:  Not connected
Cause:  The driver disconnected while associating.
Error code:  229378
Recommended actions:
The selected wireless network is out of range or unavailable. Move to a location that is closer to the access point and try again.
Verify that the encryption settings (WEP/TKIP/AES) specified in this profile match those expected by the wireless network.
Verify that the wireless adapter in your computer has not been restricted from accessing the radio channels being used by the wireless network.
Verify that the wireless network name (SSID) is specified correctly. The SSID is case sensitive.
If the problem persists, contact your network administrator and provide the troubleshooting information below.
Adapter Details
Adapter name  Intel(R) WiFi Link 1000 BGN
Adapter type  Wireless LAN
Adapter speed  54 Mbps
Driver/Firmware version  14.0.1.2/ N/A
Adapter status  Enabled
Connection Status  Not connected
Disable unused cards?  No
TCP/IP Settings
DHCP enabled?  Yes
Append parent suffixes of the primary DNS suffix?  No
Register connection's DNS suffix in registration?  No
Register connection's DNS suffix in DNS registration?  Yes
Enable LMHOSTS Lookup?  No
NetBIOS setting  "Default"
Wireless Settings
Network name (SSID)  Harvest
Connection type  Access point
Wireless mode  Auto
Security encryption  802.1x/WPA2/AES/EAP
Internet Settings
IE Settings
Home page  http://www.fyifdi.com/default.aspx
Proxy settings
Automatically detect settings?  No
Use automatic configuration script?  No
Bypass proxy for local addresses?  No
System Information
System model  42872VU
BIOS version  8DET46WW (1.16 )
Operating system version  Windows 7, Service pack 1
Access connections version  5.85
Access Point scan list
Network name (SSID)              Wireless mode MAC address                   Signal strength Channel
EnGenius1                        802.11g        00:02:6F:6E:C5:6A              23%            1
                                 802.11g        30:37:A6:C8:5B0              48%            11
                                 802.11g        00:23:33:21:9B:80              95%            1
                                 802.11g        00:14:A8:7E:60:40              25%            3
Duket Architects Planners        802.11g        00:21:29:92:57:B9              25%            6
Global Settings
Network
Allow Windows users without administrator privileges to create and apply location profiles  ->No
Allow the wireless LAN radio to be turned off when inactive  -> Yes
Enable autodeletion of unused profiles  -> No
Disable the Peer to Peer community feature  -> Yes
Allow selection of location profiles with Fn+F5 On Screen Display menu  -> Yes
Notifications
Show ThinkVantage Access Connections status icon in task tray  -> No
Show wireless status icon in task tray  -> No
Display the progress indicator window when a profile is being applied  -> Yes
Show Access connections Gauge in task bar  -> Yes
Preferences
Enable sound effects  -> No
Enable animations  -> Yes
Do not show balloon tips from the Access Connections system tray icon  -> Yes
Do not show balloon tips from the Access connections Gauge  -> Yes
Automatic location profile switching list
Include Ethernet connections in automatic switching and prompt me to save Ethernet ports  -> No
Preferred Location Of WLAN  -> No
When no other connections are available, connect through Wireless WAN or WiMAX  -> No
Wireless priority list
Selection    Priority     Location profile name                                            Connection order                 Connection details
Yes                 1     Harvest                                                          Wireless LAN                     SSID: Harvest
Log File
Debug Log is disabled
Solved!
Go to Solution.

I share your pain with same Intel WiFi Link 1000 bgn. After many, many hours yesterday I am now solidly running Wireless N at 144 Mbps on a LinkSys E4200, 99% reception from 30 feet away.
Previous to yesterday I could not get 'N' to work at all.
First, if you have a newer dual frequency Router, this Intel adapter only supports 2.4ghz..
1. I am using Access Connections 5.85, Windows 7
2. Router: 2.4 Ghz Network Mode: Mixed
3. On my LinkSys router Channel: Auto NEVER worked for either 'G' or 'N'. I picked channel 4 by chance and things got better. No further experiments.
3. Channel Width: Auto (20mhz or 40mhz).
4. Earlier forums indicate WPA2-P and AES must be selected. That's what I am running.
5. Numerous references to "power" conflicts. Set all Power Management to Maximum Power.
(Control Panel -> Device Manager ->Network Adapters -> Intel WiFi Link 1000 bgn -> Power Management)
(Access Connections -> Wireless Settings -> 4. Advanced Configuration-> Maximum Performance)
If you followed these steps, Wireless G should be working stabily for you now.
Now for the secret sauce to make Wireless N work: go to http://communities.intel.com/message/82098#82098
See Feb 3, 2010 post How to get 5100 AGN to connect at N speed?
I am indebted to this guy.
Save the instructions! For some reason my EDGE 14 wireless totally quit this week and that's what sent me down this wireless rabbit hole again. At least this time I was able to make N mode work for the first time.
Frustrated but relieved,
Lew

Share a USB Drive ?

Hi
I have just set up a new mini mac server, i managed to clone the os disk and then set them to raid 1 and then clone back the os from usb to the new raid mirror with no problems
Now i plugged in a new 2TB usb hard disk and formatted to HFS, this comes up in disk utilities, i mounted this....
Now how do i share the whole hard disk ? Or do i have to create seperate directories and share these ?
And whats AFS NFS ? etc ?
Cheers
Dave

Now how do i share the whole hard disk ? Or do i have to create seperate directories and share these ?
You can do it either way - share the entire drive, or share specific directories. Your choice.
And whats AFS NFS ? etc ?
I assume you mean 'AFP', not 'AFS', right?
There are multiple protocols used for file sharing - each developed by different companies to meet their specific needs, each have different strengths and weaknesses including client support.
NFS is the classic Network File System developed by Sun and is the standard for most UNIX environments.
SMB is Microsoft's file sharing protocol and is the standard for Windows computers.
AFP is Apple Filing Protocol developed (not surprisingly) by Apple and is the standard for Mac systems.
It's not that clear-cut, though. Most operating systems can talk multiple protocols but in general I recommend sharing the file systems via whatever the client is most comfortable with. In other words, use SMB for directories that will be shared by Windows clients, use AFP for Mac clients and NFS for UNIX clients.
Bear in mind that the options are not exclusive - it's entirely valid to share a directory via more than one protocol at a time based on the clients that will be accessing it.

How to share external USB drive connected to airport time capsule

I have a 4TB Seagate USB Hard Drive connected to my Airport Time Capsule. The Time Capsule connected to a newer iMac running Maverick.
I use the Time Capsule for Time Machines Backups and as a Router, as it was designed for.
I want to use the external Seagate drive to share content with other devices (Mac, IOS, Windows) on my home network
Problem: I cannot figure out how to SHARE the external Seagate drive so that any other devices can see it.
Steps tried: Go to System Preferences, Sharing, and I am unable to add this Seagate drive to list of sharable objects. It is grayed out.

the drive is formatted as AppleShare. Is that a potential problem?
No, that is the correct setting if you want to share out the drive.
Finally, when I run Disk Utility I don't see the Seagate drive (nor the Time Capsule) at all.
Remember that the Time Capsule is a network drive. Any other drive connected to the USB port on the Time Capsule is also a network drive.
Disk Utility cannot be used on a network drive. It only works on a drive that is directly attached to a Mac. If you need to partition the USB drive or something similar, you will need to connect it directly to your Mac for the operation.
Otherwise, everything looks correct in AirPort Utility.

I need to share an USB disk with a Vista machine

I currently have two MBP's accessing a usb drive plugged into a USB hub off an AEBS wirelessly. I need at add a Vista machine to the mix. I have Bonjour for WIndows installed on the machine and all it does it allow me to connect the the printer that is attached to the AEBS. I have Googled and found nothing that gets me a solution. This seems like it should be fairly easy or is it?
Ideally, I would like to be able to access this drive remotely from my home office. Pardon the pun, but is that even remotely possible?

That looks right.
Remote Access: Open Finder and select Go > Connect Server and type in your IP address or FQDN.
Note: Most ISP's would have blocked NetBIOS ports required for Windows File Sharing to work. And Vista will unlike to gain access to your AEBS's AirDisk.
Local Access From Windows PC: Open the AirDisk Utility and select the name of AEBS and click connect.

Suddenly can't share external USB drive

I have all of my iTunes music on an external USB drive called 'iTunes_Drive', attached to my G5 iMac in the basement. For a long time, my wife would just run iTunes on the G4 iMac in the living room and play music through the Shared Libraries feature. However, this is slow to start up each day, so I came up with the idea of just sharing the external drive, and having her maintain her own library based on the music in the shared drive.
Just today, it became impossible to access this shared drive from the G4. Interestingly, when I shared a FireWire external drive with the same settings, then that drive WAS visible as an available shared folder when connecting from the G4.
Rebooting both computers hasn't changed anything. The firewall on the G5 is turned off, and it's allowing AFP, SMB and FTP sharing of the drive. The G4 CAN mount the iTunes_Drive using SMB, but iTunes doesn't recognize it as the same drive (possibly because under SMB it's called "ITUNES_DRIVE:" whereas in AFP it's "iTunes_Drive").
Is there something new in security which is preventing AFP sharing of external USB drives? Neither googling nor searching through this forum has turned up anything that helps me.
I should note that the G5 is running Leopard 10.5.1, and the G4 is running Tiger 10.4.11, and I just ran Software Update on both computers last night, with the attendant reboots this morning.

I've experienced a similar problem with my two external hard drives connected to my AirPort Extreme Base. Since installing yesterday's security update, I can no longer see either hard drive. From my Shared folder in Finder, it's now constantly in 'Connecting' mode. I've tried rebooting and checking everything to no avail.
Any help out there would be appreciated.

Lock a USB Drive with 10.6.8

Hello, I have an original MacBook1,1 running Snow Leopard 10.6.8. I would like to password protect my USB Drive. I have heard of OS X Lion being able to password protect USB Drives but I cannot upgrade to Lion, only 10.6.8, which I'm sure you know. I have seen many apps on the Mac App Store, but none are compatible with my MacBook. (Because of my OS and 32-bit. processor.) I want the password to come up automatically when you plug in the USB Drive. Or I would like to have the password come up when you try to open up the USB Drive. I do NOT want to have one that copies something onto the USB Drive that you can put stuff in. I know that must sound very wordy. Thank you in advance.

There may be some security options in OS X Disk Utility, but to
avoid a File Vault if possible should you forget the password;
and usually a bootable full running OS X could have Security
settings in System Preferences engaged, not an external file.
You may be able to encrypt the entire content, not sure how
because after hearing horror stories of lost access to very
important files or drives, or partitions, I've not bothered; as
a single user there are other ways to lose file access that do
not involve setting up these concepts. Backups to secure a
working copy of ones archive and to have a bootable clone
are better goals to overcome other kinds of loss.
Physical access to the computer and media are the first level
of security; then passwords, then encryption, as/when needed.
While they likely do not provide a simple path to your needs
the security guides in .PDF download document form, from
Apple Support may be helpful as they cover Mac OS X 10.3
through 10.6.8.
•Security Configuration Guides - Apple Support
(Mac OS X: 10.3/10.4/10.5/10.6)
https://ssl.apple.com/support/security/guides/
Hopefully you can find a workable security measure for use
with a USB flash drive to password protect its content.
Good luck & happy computing!

Access Share - Wireless/USB Drive with KDE

Similar Messages

Maybe you are looking for