Access violation at address 00000000. Read of address 00000000. (WRT54G)
I recently started receiving the following pop up window (access violation at address 00000000. Read of address 00000000) every time I restart my machine.
Sometimes I have one pop up, other times I have to shut down because it continues to give me continuous pop ups.
Please advise.
Jose Escalante
Disconnect the Router from the computer & connect the computer directly to the Modem ...check if you are getting the same kind of Pop-ups ....
If so then there is an issue with your own Operating System ,,,,
Similar Messages
-
Access Violation when trying to read from Open Hub in BW
Hi,
Can someone help me out. I use BODS version 14.1.1.210. I have setup the connection to BW source and imported metadata for my OpenHub - no problem.
Then created DTP and processchain to load Open hub data in BW.
Made dataflow in BODS with Open Hub Tables as source and maintained processchain to be executed. When executing BODS job I get the following error:
6800 10580 JOB 17-03-2014 13:10:34 Job <Test_OpenHub> is terminated due to error <170101>.
6800 10580 SYS-170101 17-03-2014 13:10:34 |Session Test_OpenHub|Data flow Test Openhub
6800 10580 SYS-170101 17-03-2014 13:10:34 System Exception <ACCESS_VIOLATION> occurred. Process dump option is off. Process is not dumped.
6800 10580 SYS-170101 17-03-2014 13:10:34 Call stack:
6800 10580 SYS-170101 17-03-2014 13:10:34 (null)
6800 10580 SYS-170101 17-03-2014 13:10:34 Registers:
6800 10580 SYS-170101 17-03-2014 13:10:34 RAX=00000000747E1648 RBX=0000000000209AB8 RCX=0000000000209AB8 RDX=0000000000000160 RSI=000000000231DAC0
6800 10580 SYS-170101 17-03-2014 13:10:34 RDI=0000000008BEBAC0 RBP=0000000000000000 RSP=00000000002099C0 RIP=000000007477730A FLG=0000000000010206
6800 10580 SYS-170101 17-03-2014 13:10:34 R8=0000000000000000 R9=00000000FFFFFFFF R10=0000000000620064 R11=0000000008C93600 R12=000000000033D390
6800 10580 SYS-170101 17-03-2014 13:10:34 R13=0000000081D6FEC0 R14=000000000020A008 R15=000000000020A030
6800 10580 SYS-170101 17-03-2014 13:10:34 Exception code: C0000005 ACCESS_VIOLATION
6800 10580 SYS-170101 17-03-2014 13:10:34 Fault address: 000000007477730A 01:000000000002630A
6800 10580 SYS-170101 17-03-2014 13:10:34 C:\Windows\WinSxS\amd64_microsoft.vc80.crt_1fc8b3b9a1e18e3b_8.0.50727.4940_none_88df89932faf0bf6\MSVCP80.dll
6800 10580 SYS-170101 17-03-2014 13:10:34 ==========================================================
6800 10580 SYS-170101 17-03-2014 13:10:34 Collect the following and send to Customer Support:
6800 10580 SYS-170101 17-03-2014 13:10:34 1. Log files(error_*, monitor_*, trace_*) associated with this failed job.
6800 10580 SYS-170101 17-03-2014 13:10:34 2. Exported ATL file of this failed job.
6800 10580 SYS-170101 17-03-2014 13:10:34 3. DDL statements of tables referenced in this failed job.
6800 10580 SYS-170101 17-03-2014 13:10:34 4. Data to populate the tables referenced in the failed job. If not possible, get the last few rows (or sample of them) when
6800 10580 SYS-170101 17-03-2014 13:10:34 the job failed.
6800 10580 SYS-170101 17-03-2014 13:10:34 5. Core dump, if any, generated from this failed job.
6800 10580 SYS-170101 17-03-2014 13:10:34 ==========================================================
Any good ideas?Hello Erik,
not sure about it, but did you see this post some hours after yours?
DS 4.1 job aborts with Access Violation
Also, did you check ST22 to see if it generates any dump?
And if you're able to check the BODS log files, it might me helpful. They're located at %LINK_DIR%\log directory. Check the names with the execution of the job.
Hope it helps!
Regards.
Bruna Dupim -
"Access violation at address 00000000. Read of address 00000000" in Toad
Dear DBA,
I am using Oracle 10g R2 in Windows XP and Toad Version 9.6.0.27 And While Connecting to the Database , I am having *"Access violation at address 00000000. Read of address 00000000"* in Toad . Is there any Solution ?
Thanks & Regards
Vikash ChauradiaWe have the same issue here. I put a ticket in with support and received
this response
==============================
If you have two 10g clients installed only the first one listed in the
environment variable path works in Toad 9.5. The other gets an access
violation error. Could you please try and switch them just to confirm
that is the same with yours?
For Example:
1. Right Click My Computer
2. Properties | Advanced tab
3. Environment Variables
4. Scroll down system variables to Path | Edit
Path=Developer-Suite 10 GR2 ; Oracle Client 10.2.0.1.0;
to
Path=Oracle Client 10.2.0.1.0 ; Developer-Suite 10 GR2;
Thank you,
Emran Elbrashy
Senior technical consultant -
Error: Access violation at 02271d4a in module observerdll.dll read address
I am using Delphi 5, SAP DI API for SAP 2004.
On a users machine, when we try to connect, we get an error "Access violation at 02271d4a in module observerdll.dll read address 00000000".
Anyone know why they could be getting this error? And what I need to do to fix it?
thanks
BillThe problem is I have not been able to reproduce the problem on any of the machines in my office, this is only happening on a client machine. They have just the SAP client, and our program that uses the DI API.
I have instructed my client to search for that dll, and try to rename it, and rerun it. Not sure whether this will fix it or not.
Here is some example code I am using, I do not at this time know the exact point where the error is returning from, I assume from the Connect function.
function TtcSAP.Connect: string;
begin
// return empty on success
Result := '';
try
// make sure it was created
if not Assigned(oCompany) then
begin
Result := 'Error creating Company object.';
Exit;
end;
if oCompany.Connected then
oCompany.Disconnect;
// Specify the user name and password
oCompany.UserName := sUserName;
oCompany.Password := sPassword;
oCompany.DbUserName := sDbUserName;
oCompany.DbPassword := sDbPassword;
oCompany.UseTrusted := bUseTrusted;
// misc settins
oCompany.language := ln_English;
// Specify the Company database
oCompany.CompanyDB := sCompanyDB;
// specify the server
oCompany.Server := sServer;
// connect (0 = success)
if oCompany.Connect() <> 0 then
begin
Result := GetLastError;
if Trim(Result) = '' then
Result := 'Connection failed.';
end;
except
on E: Exception do
Result := E.Message;
end;
end; -
Access violation at address 67690153 in module 'ORA805.dll'. Read of addres
Hi,
Access violation at address 67690153 in module 'ORA805.dll'. Read of address 00000000
Please solve the avove problem.Mahfuz wrote:
Access violation at address 67690153 in module 'ORA805.dll'. Read of address 00000000
Please solve the avove problem.Easy. Install a supported version of Oracle. Oracle 8 is long dead. -
Hello,
We are having an issue running Diadem 8.1 on a new HP XW 9400 with Windows XP SP2. 3 errors have been occuring with frequent crashes, they are:
1) "1Exception EAccessViolation in module ntdll.dll at 000111DE. Access violation at address 7C9111DE in module 'ntdll.dll". Read address 37363430.
2) The instruction at "0x7c9111de" referenced memory at "0x352e302d". The memory could not be "read".
3) ---Error--- DIAdem
Error in Autosequence - processing in line: 74 (IARV_VAR_GET)
Runtime Error while executing command "Iarv2Txt$ := FR(T9,L1)"
Error type: ACCESS VIOLATION
Error address: 000101DE
Module name:ntdll.dll
We are using the same scripts and version 8.1 on a variety of Dell desktop computers (W2K and XP SP2) without any issue, looking for suggestions as this affects no other software on the HP XW 9400 other than DIAdem. Appreciate any suggestions.
Message Edited by swillh on 06-25-2007 08:55 AMChristian,
I will answer your questions in the text below. Thanks for your help.
Hi swillh,
I also would like to help you.
Unfortunately, The reported access violation in the central Windows ntdll.dll is very unspecific.
May be the following questions will help you to provide me more info.
1. You mentioned that the aut's and - I think - also the accessed text file reside on a server.
Is there a stable network connection?
The server can sometimes be a little slow but the connection is good. This computer is using the same connection that the prior computer utilized without issue.
Are the files accessed by multiple clients simultaneously?
It is possible that more than one computer can be accessing the same file, but again, this has never been an issue. We are reading the files only, not writing to them.
The processing routines we are running have used for over 5 years without any issues until adding this computer.
Is the text file read by one client while another client is writing the same file?
No, files are "read only"
2. Have you already tested opening the file with the FileOpen command before calling FR?
Yes
Do you see any chance to convert the aut to a vbs file? This gives you more alternatives in accessing text files.
3. What do you mean with "processing ATD's with 30 or more channels of data"? Where is the relation between ATD files and data channels?
Processing Crash Dummy data with file sets low in channel count (15 channels) result in successful processing without any crashes or access errors. When processing dummies with more than 20 channels we sometimes encounter these issues. The higher channel count may be the only common factor I can find in these faults.
Steve
Message Edited by swillh on 07-09-2007 08:44 AM -
When installing Acrobat Pro, I receive these errors:
EAccess violation in module AcrobatPro_11_Web_WWMUI.exe at 0001B7D6
access violation at address 0041B7D6 in module AcrobatPro_11_Web_WWMUI.exe Read of access 00000008
The program will not run.
Help?Sounds like you have a corrupt file and need to download again. As large as the download is, it is not surprising that an error occurs.
-
What does this error mean? Error: Access violation at address 0053DD46
I am trying to run diff reports using batch scripts, and its very puzzling that some of the diff report scripts within the batch script are running and some are not, there is no consistency to what is getting errored out.
I then tried running them manually in foreground on the client and I get the same issue. Has anyone encountered this issue? What do I make of it?,
4/24/2013 1:29:30 PM - *** MDMConnect starting ***
4/24/2013 1:29:30 PM - Logged in successfully.
4/24/2013 1:29:30 PM - Started export job for PLN_FLD_ACCT_DIFF
4/24/2013 1:29:34 PM - ERemotableException with message: "Server was unable to process request. ---> Error during Export. Export was unable to run. Error: Access violation at address 0053DD46 in module 'mdm_ntier_engine.exe'. Read of address 00000024" while running Export
4/24/2013 1:29:34 PM - => ERROR: Data Relationship Management Server returned error: "Server was unable to process request. ---> Error during Export. Export was unable to run. Error: Access violation at address 0053DD46 in module 'mdm_ntier_engine.exe'. Read of address 00000024."
4/24/2013 1:29:34 PM - *** MDMConnect stopping ***
Thank you
Tanuja DonavalliThis is issue is coherent in DRM version 11.1.1.2
Whenever a property is deleted, the references to that property would still exists/stored in tables. The next version of DRM is made to address this issue, where in it takes care of removing all references whenever we delete the property.
Cause: Properties was deleted from DRM client but the value was still stored in the compare table for Difference export and causing export to fail.
Solution: Need to recreate the deleted properties and remove the properties in the exports and delete the properties.
Going Forward: Instead of deleting the properties we need to remove the property from the export and hide the property.
Hope this helps. -
Access violation at address 6761D581 in module 'ORA805.dll'.
hi Gurus,
When ever I try to connect the database through toad , I got this error 'Access violation at address 6761D581 in module 'ORA805.dll'. Read of address 00000010'. Please help me to resolve this issue.
Oracle database: 10.2.0.1.0
Oracle client: oracle froms 6i (sql 8.0.6.0.0)
toad: 10.5.0.41
Thanks in advance
SadiqToad Advisor shows
Warnings
1- Incompatible Client and Server
Client version (8.0.6.0.0) and server version (8.0.0.0) should not be used together according to metalink note 207313.1.
Incorrect NLS_LANG
2-
NLS_LANG is AMERICAN_AMERICA.WE8ISO8859P1. Expected WE8MSWIN1252 (AMERICAN_AMERICA.WE8MSWIN1252) for Code Page 1252, Language ID 1033 (English (United States)) -
Hi All,
I'm using diadem from .net Program. While on the run I'm getting the following error.
Error While executing "" Command
Error type ACCESS VIOLATION
Error Address: 0006898E
Module name:gfsdesk.DLL
Anyone have any idea why this is happening?
regards,
SwaroopHi Swaroop,
It would be helpful to better understand what your code really does. The information that you called DIAdem from your enviroenment is not yet sufficient to understand what the problem might be.
Andreas -
Unable to access only Read Write addresses of AB Micrologix 1400 PLC using NI DSC and NI OPC server
Hi,
I have been using NI DSC and OPC servers (NI and Kepware) to communicate with Allen Bradley Micrologix 1400 PLC (1766-L32BXB). Recently at one site I found that I could access Process values from the PLC correctly (Read Only tags) but could not access the Read Write Tags at all. The latter are addresses to which it should be possible to write Set (i.e., references) values from MMI or PC software. I am able to do so from the MMI not from the PC software. I get communication error message on the MMI and PC, mentioning the PLC address being accessed (e.g. N7:0).
Support from the supplier is not available. Hence can anyone let me know if ladder logic could have been written to prevent PC software based access of Read/write addresses (N7:0 to 9 in this case), while permitting access to Read only addresses? Is the problem at the PLC end or OPC server end? Is there a way to get around this?
Thanks in advance.The OPC Server cannot force Outputs so if th registers in question are the outputs of ladder rungs you cannot write to them via the server. The controller will accept the write from the server but will not execute the write. In some cases the server event log will post an error if it is the PLC. Do you get errors when you try to write and if so what are the posted error messages.
Fred Loveless
Kepware Technologies
http://www.kepware.com -
SQL Issue Access Violation at address 09513DC9
Access violation at address 09513DC9 in module 'WDBHandler.dll'. Write of address 00000000
I use Taxware to make the backup
I don't no how to run @@ on 2005 I use SQL Server management studio
Same as you do for other SQL server versions. Just go to SSMS open new query and type below
select @@version
Can you give more error information did you got any stack dump. Can you please check SQL server errorlog . I guess this could be issue with tool you are using but not sure
Please mark this reply as answer if it solved your issue or vote as helpful if it helped so that other forum members can benefit from it
My Technet Articles -
Access Violation at Address 7C91B21A
I keep getting the following Linksys error:
"Access violation at address 7C91B21A in module 'ntdll.dll'. Write of address 00000010."
Also, whenever I open the Linksys Wireless Network Monitor, it says something about not being able to connect to/at the access point?
I'm so confused. Just yesterday, I wasn't having any problem connecting to the internet. Now, it's not even showing that I have an available wireless network. If I right click on "wireless network connection" in my network connections, and click "view available wireless networks", it doesn't show any in range!
I'm currently using my neighbor's internet (with their permission) to send this message, in an attempt at resolving the issue, but it's honestly driving me absolutely mad. Is there anyone who has any idea what the problem is?
Also, if it helps at all, I'm under the impression that my PC is the problem, as opposed to the router, because my PS3 is picking up the wireless signal just fine.
I appreciate any and all feedback!
Thanks.Un-install the Linksys Montior from the Programs Menu and then try to re-install the adapter...
If you could not un-install the adapter you should reboot the system in Safe Mode and then perform the un-install...Once un-installed you should re-install the drivers...
To re-install the Drivers insert the Linksys Setup CD into your CD-ROM drive, When the Welcome screen appears click Exit.Leave the adapter connected to the PC and reboot your computer...Once the computer is rebooted you should see a message "Found new Hardware"...When the Hardware Update Wizard window appears, click Install the software automatically (Recommended) then click Next and it should install the adapter drivers...
NOTE : This installation doesn't install the software(Linksys Monitor)...
Once the Adapter is installed, Click on the Start button >>> Control Panel >>> Network Connections- Right click on the "Wireless Network Connection" icon and select "View Available Wireless Networks"- If you see your wireless network in the list, highlight it by 'single' clicking on it- Now click on the 'Connect' button below- If your wireless network is secured, it would ask you to provide the network key- Provide the wireless network key and confirm it again in the confirmation box and click "Connect"...It should connect to your Network and Internet...
Message Edited by Klatch on 06-29-2009 01:28 PM -
Error Access violation address 000835D7
Hi,
Does anyone know what Error Access violation address 000835D7 in Diadem 2012 is??
ThanksHi Leillo,
If it never throws an error when you run it without debugging, then I'd suggest you debug with MsgBox commands instead of the VBScript Debugger. Probably it will throw an error when run without debugging, though. If you can describe a recipe for causing this error, please send/post all required files ([email protected]) and the recipe description to us, and we'll see if we can track down the problem. Those hex error codes mean nothing to me.
Brad Turpin
DIAdem Product Support Engineer
National Instruments -
Java.exe crashing with Dr Watson access violation at address 500bf974
We have been sucessfully runing an application delveloped with JDK 1.2.2 on a Pentium III machine with Windows NT 4 SP5 (384Mb RAM). I have replaced the Pentium III machine with a pentium 4 with 1Gb RAM (still running NT4 SP5). In fact, I simply took the HDD out of the PIII and installed it in the P4.
All applications work correctly (Sybiz Vision, MS Office 97 suite), however, when I go to run the java application is crashes and a Dr Watson Access Violation in java.exe error is generated.
I have:
1. Reinstalled the JDK 1.2.2.
2. Confirmed that all hardware drivers (new NIC, Video and Sound Card) were updated with the appropriate versions from the hardware suppliers web pages.
3. Read thru previous posts on this site (and others) for similar errors, but have only been able to find similar questions.
4. Lowered the video card display colours to 256 rather than 65,536.
None of the above have made any difference.
I hope this question will prompt the java/Dr Watson gurus out there to help me resolve this frustrating problem.
Thanks in anticipation.
GregConsider getting 1.2.2_014, or whatever is the latest version of 1.2.2. I think there were some issues with Pentium IV processors which were fixed in one of the later incarnations of the JDK.
You can get the latest version of 1.2.2 from the following url:
http://java.sun.com/products/jdk/1.2/download.html
Maybe you are looking for
-
2.6.24 - which module is loaded [rt2x00 problem]?
Hey, I recently upgraded to 2.6.24 because I wanted to use the new rt2x00 wifi modules. But, those modules are really crappy and buggy - so I want to continue using the 2.6.24 kernel, but switch back to the legacy rt73 wifi module. I managed to compi
-
How do I recover my contact list which I lost while transferring it from iphone3gs to windows address book.
-
How to Set A Default Start Time For New Events In Calendar?
How to Set A Default Start Time For New Events In Calendar?
-
Is it possible to make a hierarchy of application ...
I can add a new folder to the root folder but it doesn't seem possible to move an application folder to the new folder. One can only move applications to the new folder. What I want to do is to create a folder in the Main/Root menu called something l
-
please help. i did a hard reset. now the palm desktop has my contacts and calendar. i'm trying to get them back to my treo by sync-ing. but they won't come back to my handheld! arrgh! does anyone know how to get the contacts back after a hard reset?