Access violation error message 'WMP54GSv1_1.exe'

Hi,
Each time I start my Compaq Presario, I get the following Error message: "Access violation at address 004A55F7 in module ‘WMP54GSv1_1.exe’. Read of address 00000000." I cannot view wireless networks or access internet.
I have a Linksys wireless card in my PC and it just came back from HP for faulty on/off switch servicing.
How do I rememdy this situation?
Thanks!!
TJ

The drivers you need to download are your correct product model number and version which you may find underneath the card itself on one of the stickers... or with the card box (if you still have it)
After you have downloaded them, just 1st transfer them into the non-working PC... the file might be zipped... so you might need to unzip them first...  you then uninstall the card from the PC... either go to add/remove programs and add/remove hardware....
Then restart the PC... after you restart it, you will probably be prompted for a "found new hardware wizard"... just go through the process... if it asks your for the drivers.. select "specify a location and specify the folder where you actually unzipped the files...
Sounds lengthy I know...

Similar Messages

  • "Access Violation" error messages in Diadem 9.1

    We have recently purchased Diadem V.9.1 and are encountering numerous "Access violation" errors as well as Runtime errors.The most frustrating aspect of trying to run this software are the constant crashes we are experiencing.
    It is taking us 3X as long to process one subject as it should.  I posted a request to NI technical help but I think it is the Thanksgiving holiday in the US.

    Actually, DIAdem 9.1 is a very stable version. If you are continuously
    experiencing crashes this might be due to some problems with your
    computer hardware or configuration.
    Is your PC matching the recommended system requirements as found in the
    helpfile? What OS are you using, did you install the most recent
    servicepacks?
    Do you have similar problems with other software on this computer as
    well?  Unexpected system crashes often occure because of corrupt
    RAM chips. DIAdem is using a lot of memory - so maybe you are accessing
    regions that other programs dont use and  - for that reason - see
    the crashes only in DIAdem.
    You are writing that the processing takes 3 times longer than expected.
    How do you compare? Have you been using elder versions of DIAdem which
    were faster, or are you comparing with the processing speed of another
    computer?
    There are some things I would do to try to improve the performance.
    Check that you have at least 256MB RAM
    Check that you are using Windows 2000 with servicepack 4 or XP with servicepack 1 at least
    Reinstall DIAdem, use the version 9.1 SP2 instead of the installer you have been using. You can download this installer here.
    Add servicepack 2b afterwards. The latter is a selfextracting zipfile
    which has to be unpacked in the DIAdem directory while the first is a
    complete DIAdem installer.
    Replace the RAM modules of your PC.
    You are welcome to post again if you dont get any further. In this case
    please give some more information about the system such as CPU, OS,..
    and the crashes. When do they occure? Is it a specific function or
    module you are using when DIAdem crashes. What does the error messages
    tell you about the module in which the exeptions occure?
    Regards
    Ingo Schumacher
    Systems Engineer Sound&VibrationNational Instruments Germany

  • How to address  access violation error message

    Hi Experts,
    I got message as
    ~Errors in file d:\oracle\product\10.2.0\admin\sale\bdump\sale_p003_5996.trc:~ORA-07445: exception encountered: core dump [ACCESS_VIOLATION] [_kxsdcbc+506] [PC:0x8AAE62] [ADDR:0x18] [UNABLE_TO_READ] []~ORA-00600: internal error code, arguments: [5351], [4425995], [1712], [], [], [], [], []~
    What means about this message?
    What do I need to do?
    our system as oracle10gR2 in window 2003
    Thank
    Jim

    user589812 wrote:
    Hi Experts,
    I got message as
    ~Errors in file d:\oracle\product\10.2.0\admin\sale\bdump\sale_p003_5996.trc:~ORA-07445: exception encountered: core dump [ACCESS_VIOLATION] [_kxsdcbc+506] [PC:0x8AAE62] [ADDR:0x18] [UNABLE_TO_READ] []~ORA-00600: internal error code, arguments: [5351], [4425995], [1712], [], [], [], [], []~
    What means about this message?
    What do I need to do?
    our system as oracle10gR2 in window 2003
    Thank
    Jimora-07445 and ora-0600 are deep internal errors. You need to go to MetaLink, where they have a lookup tool specifically for these error codes.

  • Java.exe Access Violation Error(URGENT)

    Hi all,
    I have created a application for my company. This application requires a user to login into the site by giving his userid/pwd. Once the person logs into the site, there is this error "Java.exe Access Violation Error" which pops up and terminates the Web Server.
    My Login page is a HTML page which inturns calls a Jsp which authenticates the user.Once the authentication is completed, the user id is put into the session so i can check for the existence of user session on each subsequent page. After the user successfully logs in, the error pops up.
    Please get back to me incase u have ever encountered this error and what might be the solution.
    I am using Tomcat Webserver 3.2.3, Sql Server 7.0 as the Database Server, JDK1.3 .
    Regards,
    Yatin

    As far as i remember i faced this problem when the memory of my pc was broken. So it may not be a problem of java or html code.

  • JDeveloper 3.2 Problems - Access violation errors

    Hi,
    I suddenly got the following error message on a dialog box when I was editing code in the visual designer:
    QUOTE
    Access violation at address 00402FC8 'jdeveloper.exe'. Read of address FFFFFFF
    UNQUOTE
    When I tried to save my work, I was not able to received a similar message. When I tried to exit, I recived the following message:
    QUOTE
    JDeveloper was unable to autosave the current workspace. Do you wish to close the workspace anyway?"
    UNQUOTE
    After exiting the workspace, I was not able to reopen the workspace. I created a new workspace and added my projects to the new workspace. I was happy that I did not lose my work.
    I have received the access violation error before. I do not know what causes it and I would appreciate very much if the JDev team explains why such an error occurs.
    Thanks.

    Hi,
    We intermittently see postings of this kind. The more information you can provide us about your environment and what you are doing when you get the error, the better:
    1. What OS are you running (include version and SP).
    2. What kind of processor does your machine run?
    3. Do you have a single processor or multiple?
    4. What kind of project were you working on? Did you create an empty project and a new class file and were just editing source code, or did you create some initial content using one of the wizards from the Object Gallery and were modifying the generated code, or did you import existing code from some other location?
    5. How many source files did you have in the project?
    6. Was the source file you were editing a .java file, or a .jsp, .xml, .html?
    7. Does this happen frequently, or is this the first time? Has it happened since?
    Again, the more detail you can provide, the better we are able to identify possible sources of trouble.

  • Access Violation error with Diadem 2011

    I've started using Diadem 2011, and have run into an Access Violation error when loading some of my existing reports.  I've created a simple example which shows what's happening:
    I've created a simple Bar plot:
    If I change the left hand bar to be "Filled" instead of "Right Diagonal", Diadem throws up an access violation error.  I've attached the TDM and TDR files used to create the graph.  The error in the log file is:
    139  Error while executing "" command
         Error type: ACCESS VIOLATION
         Error address: 0004F5E5
         Module nameIAdem.exe
    Diadem: 11.0.3f4563 TDM
    USI: 1.9.0f4551
    DataFinder: 3.0.0f4556
    (By the way, it would be great to be able to copy those version details directly from the About page!)
    Attachments:
    Data.zip ‏7 KB

    I've tried this as administrator, and have exactly the same issues, so it doesn't appear to be a permissions problem.  I've uninstalled and reinstalled DIAdem and everything's the same.
    Here's another ZIP file with hopefully all of the required files.  I've created the data files from scrathc several times, and see the same problem.  One other thing I've just noticed is that it only occurs when filling the bars with the color Black, not blue or red or anything else.
    Attachments:
    Data.zip ‏9 KB

  • How to resolve and debug access violation Error.

    Hello
    I'm stucked with an access violation error which forces my exe build to shut down. I tried also from development environment but its the same there. The error happens after 5-60minutes.
    I played around with disabling a part of the program where it was possible and I think I'm now able to accuse the vi "gastimer.vi". But since this vi leads through the measurement procedure, there are some commands outgoing which I was not able to map one to one.
    My question is: what can cause such access violation errors? I have no dll calls, no third party library, actually the hardware communication is done serial by COM ports. The architecture principle is something adapted from producer consumer loop, except that i have often more than one consumer, so I called them like controller loop - multiple task. The communication within this loops (tasks) are done by queue cluster with an enumerator and variant.
    The indicted vi "gastimer.vi" was transfered from an older and more simply architecture. This vi works with sequence structure and a lot of local variables.
    Since I'm testing sensor on their response to gas concentration I have 10 comports to which I'm listening in parallel.
    What styles or archtiecture are prone to access violations? Where can they happened? where should I look more carefully in the code?
    How can I use the desktop execution trace toolkit to get more information about the cause of the access violation?
    Attached are two different lvlog but I guess with the same error source. In the second lvlog are two vi's named. What have they to do with the access violation error? What kind of information can i get from these lvlog files?
    Last attachement shows a runtime fatal error which happens quite a bit frequently in the recent time when working with this project. Might there be a connection, propably a crashed vi, typedef or whatever?
    Thanks for any help
    U. Siegenthaler
    Solved!
    Go to Solution.
    Attachments:
    first.zip ‏203 KB
    second.zip ‏40 KB
    Fatalerror.PNG ‏21 KB

     Have you checked your code to try to isolate any areas of possible memory leaks? I was able to find some discussion forums with similar problems. Check out the links below to see if any of these resources can be of assistance to you. 
    "Exception: Access violation (0xC0000005) at EIP=0xFDD76383" 
    http://forums.ni.com/t5/LabVIEW/Exception-Access-violation-0xC0000005-at-EIP-0xFDD76383/m-p/2257502 
    "Exception: access violation (0xc0000005) at EIP=0x00BD0984 " 
    http://forums.ni.com/t5/LabVIEW/Exception-access-violation-0xc0000005-at-EIP-0x00BD0984/m-p/2303864 
    "Access violation (0xC0000005)" 
    http://forums.ni.com/t5/LabVIEW/Access-violation-0xC0000005/m-p/2269694 
    Let me know what you find and if you have any other questions. 
    Best regards
    Matijas

  • ACCESS VIOLATION error in Report

    Hi,
    I am getting an access violation when trying to save a report.  The report only has two worksheets.  ONe is a table of contents and one of them is a template for plotting data.
    Error while executing "PicSaveAs(FileDlgName)" command
    Error Type: ACCESS VIOLATION
    Error Address: 89FFEE10
    Module Name: DIAdem.exe
    I am using Diadem 2011.
    Basically, I am trying to create a template file to make plots with.  I have a script that copies my template plot, plots the next channel, and repeats for all channels in the data portal.  The script works fine, and I got it to run once.  HOwever, I wanted to make a change, and something happened to my original template file.  So I open my report with 100 pages, delete all pages (and by the way WHY CAN I NOT DELETE MORE THAN ONE PAGE AT ONCE?  this is very annoying that i have to do this one at a time (and confirm every time) either by manage or delete options) except one, and I try to save this as my template plot and I get this error...tried several times...Any ideas?
    jason

    Hello Jason,
    a workaround for you could be to open two instances of DIAdem. Open your report in DIAdem one.
    Open first page and select "Edit->Select All" and "Edit->Copy" go to your second DIAdem and open Report with an empty report. Select "Edit->Paste" and your template is restored.
    Greetings
    Andres
    P.S.: Please post your report anyway if possible to help us to find the issue.

  • My iTunes will not start.  The box on the error message APSDaemon.exe,  And message says "This application failed to start because MSVC80.dll was not found.  Reinstalling may fix."  I did the reinstall and I get the same error.

    My iTunes will not start.  The box on the error message APSDaemon.exe,  And message says "This application failed to start because MSVC80.dll was not found.  Reinstalling may fix."  I did the reinstall and I get the same error.  The error first happened after I approved the an iTurns update.

    Same problem today. Took five times to reinstall without any error messages. Apple has posted a way to fix and you should follow their's first. I finally got to upldate correctly by doing their fix but with one difference. I did the following:
    1) Went to the C:\program files (x86)\iTunes and C:\program files\iTunes folders and moved every file ending in .dll to the desktop (even if two files in same location had the same name, just replace)
    2) Restarted computer and still got error message
    3) Uninstalled all apple programs possible in the following order......itunes, apples software update, apple mobile device support, bonjour, and apple application support.....all performed using the microsoft control panel
    4) put all the .dll files on the desktop in the trash and emptied (this is a step apple support did not specifically put in their fix but for a final try I wanted to delete everything apple).
    5) Restarted computer.
    6) Re-installed itunes from apple website
    No error messages during re-install and was able to open shortcut in one try. Even updated my ipad to make sure everything was working.

  • Error while executing "" command Error type ACCESS VIOLATION Error Address: 0006898E Module name:gfsdesk.DLL

    Hi All,
    I'm using diadem from .net Program. While on the run I'm getting the following error.
    Error While executing "" Command
    Error type ACCESS VIOLATION
    Error Address: 0006898E
    Module name:gfsdesk.DLL
    Anyone have any idea why this is happening?
    regards,
    Swaroop

    Hi Swaroop,
    It would be helpful to better understand what your code really does. The information that you called DIAdem from your enviroenment is not yet sufficient to understand what the problem might be.
    Andreas

  • When starting my computer I get the error message "AppleSyncNotifier.exe Entry point not found. this has only appeared since my last upgrade.

    Since recently upgrading to the latest ITunes,on start up I get an error message:
    "AppleSyncNotifier.exe Entry point not found .
    Procedure entry point xml TextReader Constname could not be located in
    the dynamic link library libxml2.dll"
    Any body come across this? Any solutions? 

    Doublechecking, Dad:
    I have also reloaded all other iTunes software.
    Did you use the following document as a guide?
    Removing and reinstalling iTunes, QuickTime, and other software components for Windows Vista or Windows 7
    (If we're looking at program file damage down in Apple Application Support or Apple Mobile Device Support, the 2. Verify iTunes and related components are completely uninstalled section is very important.)

  • TS1286 At my PC startup, I get an error message "AppleSyncNotifier.exe--Entry Point Not Found"  My iPhone now doesn't show up as a Device in either iTunes or My Computer on my PC. I've uninstalled/ reinstalled iTunes & run diagnostics-no luck. Ideas?

    At my PC startup, I get an error message "AppleSyncNotifier.exe--Entry Point Not Found"  My iPhone now doesn't show up as a Device in either iTunes or My Computer on my PC. I've uninstalled/ reinstalled iTunes & run diagnostics-no luck. Ideas?

    I think my problem is fixed now.
    For the fun of it, I reinstalled iTunes 9.2.1 today (using the exact same installer as I did yesterday), but this time I didn't uninstall iTunes first. As expected, iTunes recognized my iPhone (as I expected it to, until my next reboot).
    A few minutes later, Software Update showed up and among the updates is "iPhone SDK Compatibility Update". The description indicates that installing this should fix an issue where iPhones and iPod touches aren't recognized by iTunes. Isn't that interesting?
    I installed that update and most of the others waiting for me (including Java, Safari 5.0.1, and a few others - not 10.6.4 though, due to the issues with nVidia graphics cards). After the reboot, I started iTunes, and it saw my iPhone!
    So, if you're having this same problem, I'd recommend tracking down this update and see if that does the trick for you. Hopefully it will.

  • When I try to start iTunes I get the following error message: Itunes.exe – Entry Point Not Found - The procedure entry point kCMByteStreamNotification_AvailableLengthChanged could not be located in the dynamic link library CoreMedia.dll.

    When I try to start iTunes I get the following error message: Itunes.exe – Entry Point Not Found - The procedure entry point kCMByteStreamNotification_AvailableLengthChanged could not be located in the dynamic link library CoreMedia.dll.

    Any answers how to fix it? All Im getting is error for the past 3 days!

  • HT4913 How do I resolve this issue when I try to download iTunes. I receive this error message " iTunes64Setup.exe is corrupt or invalid"

    How do I resolve this issue when I try to download iTunes on my laptop?  It fails because of this error message " iTunes64Setup.exe is corrupt or invalid"

    That suggests that the installer is getting damaged during the download.
    I'd first try downloading an installer from the Apple website using a different web browser:
    http://www.apple.com/itunes/download/
    If you use Firefox instead of IE for the download (or vice versa), do you get a working installer?

  • Error Message: itunes.exe corrupt file

    Error Message: itunes.exe corrupt file
    \ipod_control\itunes\temp
    run chkdsk utility
    Itunes gives me this message, then acts normal
    downloads latest podcasts and videos but when I turn on the ipod video it hasn't been updated at all.
    Also from the start menu, I've tried to run chkdsk utility. when I do it does something 3-4 seconds and then that's it.
    My ipod shuffle works fine.
    Anybody have any ideas.
    Thanks

    try installing de software of that ipod, reinstall de ipod sofware and the itunes, after that go 2 apple.com and download the new updator. then install that too, and if possible redownload the new version of itunes. b4 u do all this , delete the software (old one ) of that ipod and itunes.. only the one that is giving u the problem, meaning b4 u reinstall the software that came with ur ipod, go 2 control panel.2.find add /remove programs.3then delete the old ipod and itunes software. then retstart ur computer. 4 then now go and reinstall the ipod software and itunes that came with ur ipod then after that redownload de ipod updator(new version is march 2006. get this and after that download the new version of itunes. then install all these, then u can also restore ur ipod by clicking on de updator when it opens press restore u will be commanded 2 plug in ur ipod. then follow de instructions. after all these ur itunes should be fine, and ur ipod software should be fine. ur itunes is corrupt , that might be causing the problem.

Maybe you are looking for

  • Probably a stupid display question

    I shoot with a canon xh-a1 edit with a mbp 15". What im wondering is if I wanted to edit on a bigger screen then my laptop and do some coloring, would it be stupid to think that using a lcd tv as a display would work? The reason I ask is I could go t

  • Two sided printing with wordperfect HP Photosmart 6515

    Any ideas how to set up two sided printing with wordperfect documents using  HP Photosmart 6515

  • How to add a custom element to a SOAP Header in c#

    I am new to SOAP and web-services, and not an expert on c# either so sorry if I have made an infuriatingly simple error. I am calling several web-services and I now need to add an element called *pcimask* to the SoapHeader in order to get a response

  • Panel, title window buttons

    Hi everybody I wonder, i know its possible to add buttons, to the titlebar of a title window, but i don't know how its done, can someone explain me please? or send me a link with a tutorial. Also i'd like to know if its possible to add another type o

  • Validating Opportunity close date

    I was requested to create a validation for Opt. Close Date - Something like: If changed from the previous value it should be in the same quarter. Other than that it would be invalid. I still trying but started using PRE(JulianQtr([<CloseDate>])) and