Accessing the internet from flash player

Im can't view the Global security settings panel on the adobe
site. Its just a blank space. any ideas why I cant view it?
I have the latest flash player, using flash 6 to create a
small header animation to access a website. Had no problems ion the
past.....

OS 9 has no built-in ability to share an Internet connection.
You will need a software router like IPNetRouter to share the dial-up connection out to the Ethernet port.

Similar Messages

UNABLE TO ACCESS THE INTERNET FROM LOCAL PROVIDER ON A SITE-TO-SITE VPN CONNECTION

Dear All,
I have a site-to-site connection from point A to point B. From point B i am unable to access the internet from local internet provider.
I am trying to ping from 192.168.20.1 the dns 8.8.8.8 but i receive the message "destination net unreachable".
When i run "show ip nat translation" i receive nothing.
The vpn connection is working properly, i can ping the other side 192.168.10/24
Below is the configuration of the cisco router on point B.
dot11 syslog
ip source-route
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.21.254
ip dhcp pool voice
network 192.168.21.0 255.255.255.0
default-router 192.168.21.254
option 150 ip 192.168.5.10
ip cef
ip domain name neocleous.ru
ip inspect name IOS_FIREWALL tcp
ip inspect name IOS_FIREWALL udp
ip inspect name IOS_FIREWALL icmp
ip inspect name IOS_FIREWALL h323
ip inspect name IOS_FIREWALL http
ip inspect name IOS_FIREWALL https
ip inspect name IOS_FIREWALL skinny
ip inspect name IOS_FIREWALL sip
no ipv6 cef
multilink bundle-name authenticated
vty-async
isdn switch-type primary-net5
redundancy
crypto isakmp policy 5
hash md5
authentication pre-share
group 2
crypto isakmp policy 10
encr aes
authentication pre-share
group 2
lifetime 28800
crypto isakmp policy 50
encr 3des
hash md5
authentication pre-share
group 2
crypto isakmp key Pb85heuvMde9Wdac5Qohha7lziIf142u address [ip address]
crypto isakmp invalid-spi-recovery
crypto isakmp keepalive 10
crypto ipsec transform-set TRANSET esp-aes esp-sha-hmac
crypto ipsec transform-set TRANSET2 esp-des esp-md5-hmac
crypto ipsec df-bit clear
crypto map CryptoMAP1 ipsec-isakmp
set peer [ip address]
set transform-set TRANSET
match address CryptoACL
interface FastEthernet0/0
description Primary Provider
ip address [PUBLIC IP MAIN PROVIDER] 255.255.255.252
ip access-group outside_acl in
ip mtu 1390
ip nat outside
ip virtual-reassembly in
load-interval 30
duplex auto
speed auto
crypto map CryptoCY
crypto ipsec df-bit clear
interface FastEthernet0/1
description TO LAN
no ip address
load-interval 30
speed 100
full-duplex
interface FastEthernet0/1.1
description DATA VLAN
encapsulation dot1Q 20
ip address 192.168.20.254 255.255.255.0
ip access-group inside_acl in
ip nat inside
ip inspect IOS_FIREWALL in
ip virtual-reassembly in
ip tcp adjust-mss 1379
interface FastEthernet0/1.2
description VOICE VLAN
encapsulation dot1Q 21
ip address 192.168.21.254 255.255.255.0
interface Serial0/2/0:15
no ip address
encapsulation hdlc
isdn switch-type primary-net5
isdn incoming-voice voice
no cdp enable
interface FastEthernet0/3/0
no ip address
ip access-group outside_acl in
ip nat outside
ip virtual-reassembly in
shutdown
duplex auto
speed auto
crypto map CryptoCY
ip local pool VPNPool 192.168.23.2 192.168.23.10
ip forward-protocol nd
ip http server
no ip http secure-server
ip nat inside source list nat_list interface FastEthernet0/3/0 overload
ip route 0.0.0.0 0.0.0.0 [default gateway ip]
ip access-list standard VTY
permit 192.168.20.0 0.0.0.255
ip access-list extended CryptoACL
permit ip 192.168.20.0 0.0.0.255 192.168.3.0 0.0.0.255
permit ip 192.168.21.0 0.0.0.255 192.168.5.0 0.0.0.255
permit ip 192.168.21.0 0.0.0.255 192.168.6.0 0.0.0.255
permit ip 192.168.21.0 0.0.0.255 192.168.12.0 0.0.0.255
permit ip 192.168.21.0 0.0.0.255 192.168.2.0 0.0.0.255
permit ip 192.168.20.0 0.0.0.255 192.168.10.0 0.0.0.255
permit ip host 192.168.22.1 192.168.5.0 0.0.0.255
permit ip host 192.168.20.1 192.168.5.0 0.0.0.255
permit ip host 192.168.22.1 192.168.6.0 0.0.0.255
ip access-list extended DFBIT_acl
permit tcp any any
ip access-list extended inside_acl
permit ip 192.168.20.0 0.0.0.255 host 192.168.3.35
permit ip 192.168.20.0 0.0.0.255 host 192.168.3.39
permit ip 192.168.20.0 0.0.0.255 host 192.168.3.23
permit ip 192.168.20.0 0.0.0.255 host 192.168.3.18
permit ip 192.168.20.0 0.0.0.255 host 192.168.3.55
permit ip 192.168.20.0 0.0.0.255 host 192.168.10.144
permit ip 192.168.20.0 0.0.0.255 host 192.168.10.146
permit ip 192.168.20.0 0.0.0.255 host 192.168.10.141
permit ip host 192.168.20.253 host 192.168.3.21
permit ip host 192.168.20.254 host 192.168.3.21
permit ip 192.168.20.0 0.0.0.255 host 192.168.3.10
permit ip 192.168.20.0 0.0.0.255 host 192.168.20.254
ip access-list extended nat_list
deny ip host 192.168.20.254 192.168.10.0 0.0.0.255
deny ip host 192.168.20.254 192.168.3.0 0.0.0.255
deny ip host 192.168.20.1 192.168.3.0 0.0.0.255
deny ip host 192.168.20.1 192.168.10.0 0.0.0.255
deny ip host 192.168.20.2 192.168.3.0 0.0.0.255
deny ip host 192.168.20.2 192.168.10.0 0.0.0.255
permit ip host 192.168.20.1 any
permit ip host 192.168.20.2 any
permit ip host 192.168.20.254 any
ip access-list extended outside_acl
permit gre any host [ip address]
permit esp any host [ip address]
deny ip any any
ip sla 2
icmp-echo 192.168.10.254 source-interface FastEthernet0/1.1
frequency 180
timeout 500
ip sla schedule 2 life forever start-time now
logging 192.168.3.21
route-map DFBIT_routemap permit 10
match ip address DFBIT_acl
set ip df 0
route-map ISP2 permit 10
match ip address nat_list
match interface FastEthernet0/3/0
route-map nonat permit 10
match ip address nonat_acl
route-map ISP1 permit 10
match ip address nat_list
match interface FastEthernet0/0

You cannot access internet, because all traffic is tunneled for VPN !!!!
Please see cisco tech documentation and bypass traffic for internet.
eg. if lan traffic is going from site a to site b then through vpn
else
lan traffic to internet (any) should be out thorugh the vpn .

I keep getting popups while I am on the internet. Flash player is trying to automatically connect. Whether I say accept or deny, nothing happens and the popups continue.

I keep getting popups while I am on the internet for flash player connection. Whether I accept or decline, nothing happens and the popups continue.

Hi sallym6620766,
We need a bit more info in order to attempt to provide assistance. Please provide the following information:
Your operating system & version
Your web browser(s) & version
Your Flash Player version
Explain your problem in step-by-step detail if possible
A direct link to a page that demonstrates the problem
If you get error messages, please quote them exactly, or provide a screenshot: http://forums.adobe.com/thread/1070933
Maria

Does iTunes use Internet Explorer to access the internet from a PC with Windows Vista?

Does iTunes use Internet Explorer to access the internet from a PC with Windows Vista?

Are you using Windows XP or Windows Vista?
Did you remove iTunes and the other Apple software also, and then reinstall iTunes.
Removing and Reinstalling iTunes, QuickTime, and other software components for Windows XP
Removing and reinstalling iTunes, QuickTime, and other software components for Windows Vista or Windows 7
Did you try to put the iPhone into recovery mode?

Accesseing the internet from my Nokia 6600 on my P...

I have still not been able to access the Internet from my Nokia 6600 to my PC. I have tried using bluettoth to no avail. Can someone help me. If you have accessed your internet from your Nokia 6600 to your PC please tell me how to do this
I will truly appriciate it.
Moderator note: e-mail address remived, it is unwise to publish personal contact info on the web.
Message Edited by michaels on 01-Oct-2008 03:19 PM

I ain't got a Nokia 6600 but all models of Nokia with modem works the same way. I don't advice using bluetooth for connection is rather erratic; use cable. Make sure all configurations of phone from providers are configured like data access points. I presumed you have loaded succesfully pcsuites, in the same way the modem drivers. You can check it in your pc/laptop devices config.
Configure your browser to connect by dial-up connection(tel no. & sometimes user/password from provider), select the Nokia modem(sometimes better to disable temporarily the built-in modem of PC/Laptop if it exist), you'll be connecting by gprs & there is tariff per minute connections more expensive than landline by modem of PC/laptop.
Knowledge not shared is knowledge wasted!
If you find it helpfull, it's not hard to click the STAR..

How to make Firefox access the internet from Oracle Ent. Unbreakable Linux?

Hello
I have a Dell Duo Core x86 laptop that multiboots Windows 2003 Server, Windows XP and Oracle Enterprise Unbreakable Linux. I use Internet Explorer to
access my email while at the library so I know my laptop can access the internet. I just installed the Oracle Enterprise Unbreakable Linux in text mode and
I can still access the Internet but only if I use one of the Windows operating systems which is why I am keeping them for now. The reason is because when I
use Oracle Enterprise Unbreakable Linux, when I select Firefox to access the internet I get these messages:
"Server not found
Firefox can't find server at www.hotmail.com
-check address for typing errors
-if unable to load pages check network connection
-if computer or network protected by firewall make sure Firefox permitted to access
web"
None of those reasons are true for not gaining access to the internet. I want to use Oracle Enterprise Unbreakable Linux from now which is why I installed
but I need to know:
1) Why do I get the "Server not found" and the other error messages when I try to access the internet using Firefox and what do I have to do to make Firefox
access the internet successfully?

Hi,
First you must confirm your laptop with Oracle Enterprise Unbreakable Linux can access internet.
Please open a terminal, input the following command
1.ifconfig
2.cat /etc/resolv.conf
Regards
Jason

I can't access the internet from my home wi-fi. It works on other wi-fi, and my wi fi is working on my h ome computer. I keep getting a message that says it can't access the server

I can't access the internet using my home wi-fi. My wi-fi is working on my home computer, and the itouch can access the internet at another person's home using their wi-fi. I've looked in the settings, and can't seem to see any differences.....i'm a techno dummy - so please respond in very basic info

Before resetting try restarting. Or you can go to Settings from the home screen > Wi-Fi > your network and scroll down to 'Renew Lease' and press that. When you do you should see a button labeled 'Renew Lease?' and another labeled 'Cancel'. Select 'Renew Lease'.
You can either back out of that screen back to the home screen or just use the return button to go back to the home screen. Then select Safari and see if you can hook in.
I have to go through that process every five or ten minutes or so when in the second story of our house - weak router signal up there.

Network Two Macs, access the internet from both.

Frustration.
I have a Mac Pro, and an older Power Mac G4. I had them networked in such a way as both could access the internet. The G4's access stopped working because I had a power outage, and had to restart everything. I am guessing this has something to do the cable modems MAC address.
At any rate: Here is what I have. A LinkSYS Cable Modem, A Netgear Switch (8 Ports) and the 2 computers. Both computers are connected to the switch. The cable modem is in port 1, the MacPro port 2, The G4 Port 3. The MacPro, does connect to the Internet. The G4 does not. I had this working before. It worked wonderfully. But I think after restarting everything, and somehow not getting the sequence right or something, I cannot get it back to working. I don't want a router. As it slows down my 16MB per sec net connection, and ruins the ping rate for gaming.
Any input, light you can shed on this situation is of course greatly appreciated. Merry Christmas!

Austinscott wrote:
Frustration.
I have a Mac Pro, and an older Power Mac G4. I had them networked in such a way as both could access the internet. The G4's access stopped working because I had a power outage, and had to restart everything. I am guessing this has something to do the cable modems MAC address.
Nope. The MAC address does not change. The IP address might change.
At any rate: Here is what I have. A LinkSYS Cable Modem,
what model cable modem?
A Netgear Switch (8 Ports) and the 2 computers. Both computers are connected to the switch. The cable modem is in port 1, the MacPro port 2, The G4 Port 3. The MacPro, does connect to the Internet. The G4 does not. I had this working before. It worked wonderfully. But I think after restarting everything, and somehow not getting the sequence right or something, I cannot get it back to working. I don't want a router.
I suspect that you have a router, built into the cable modem. Virtually all Linksys cable modems have a router built into them. In addition, unless you have arranged to have two Internet connections from your cableco, you must have a router to have two devices connected to the Internet. If you have a router you can have multiple devices on one connection. If you don't, you can have only one. You may have turned off the router functions on your modem. What is the IP address showing on your Mac Pro? If it is something in the 192.168.x.y range, where 'x' is a number from 0 to 255 and 'y' is a number from 1 to 254, or in the 172.z.x.y range where 'z' is a number from 16 to 31, or in the 10.x.x.y range, then you probably have a private network which means that you have a router built into that modem and its router functions are turned on. If your IP is a different number you probably either don't have a router built in (unlikely) or its router functions are off (very likely).
If your have a private network and your G4 is not connecting, you need to determine what the IP is on the G4. If it is 0.0.0.0, then you have a damaged network card and need to replace it. If it is 169.254.x.y then your G4 is not seeing the router for some reason, likely because the router functions on your modem are off. If it is something else we need to know what it is.
As it slows down my 16MB per sec net connection, and ruins the ping rate for gaming.
Any input, light you can shed on this situation is of course greatly appreciated. Merry Christmas!

Access the internet from my laptop

This may be a silly question but I have not had this type of phone before and before I do away with my home internet I need to know how this is going to work.....
Can you access the internet if connected to the phone via your laptop or do you have to have a hotspot in order to have internet access?

do your research BEFORE you cancel your online service. the above post is correct. you can't be on the phone while it is being used as a hot spot. and you have to have the additional subscription service to use it as a hot spot. it's at least $20 (i thought it was $30) per month....on top of your data plan.

Why can my macbook only access the internet from certain wireless sources?

I have tried connecting to the internet at my friends houses with my macbook but even though I can join the network, the internet itself doesn't work. Is there a reason for this? I've even tried to connect to the internet through a wireless network that my friend was accessing with no problem, from his macbook.

Possible reasons for being unable to connect to a strange network:
- Wrong proxy information
- Wrong network password
- Your friends router has "MAC address filtering" turned on.
You might find you can connect by creating a new location like this:
System Preferences > Network
Select the AirPort from the left hand side
Click on the Locations combo box and select Edit Locations...
Click on + to add a new location, give it a memorable name
Select the AirPort tab and enter your network name
Select TCP/IP tab.
Configure IPv4 Using DHCP
Now click on Renew DHCP Lease. After a few seconds you should get an IP address (probably 192.168.x.x)
Click on Proxies tab.
Select Auto Proxy Discovery and Use Passive FTP
Click on OK and Apply, etc.

I can't access the internet from itunes?

I can't access the ITunes store from ITunes and CD titles aren't loading.
Under one user ITunes locks up when I insert a CD

Try:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Download the song on your syncing computer and sync via iTunes.
Then delete/redownload as necessary.

Most times i am not within range of a wi-fi connection if there something i can add to my ipod touch to access the internet from afar?

Hello Most times I am not within range of a wi-fi connection is there something i can add to my ipod touch to connect to the internet ?

You can purchase a MiFi or similar device. It acts like a wifi hotspot and connects to the internet via a cellular connection. You need a data plane too.
https://www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=1&ved=0CHsQFjAA&ur l=http%3A%2F%2Fwww.verizonwireless.com%2Fb2c%2Fmobilebroadband%2F%3Fpage%3Dprodu cts_mifi&ei=rcWKT-jeBYes8ATi7pDeCQ&usg=AFQjCNGEnpTkiGCnUOHacw5dEOr0BOc7zg&sig2=M 4Xf1Hglj2FYYYfnC5rJTg

I can't access the internet from my iPad! I have Wi-Fi but my iPAD won't allow me to join. Any suggestions?

I have tried to reset my Wi-Fi settings. I have powered my iPad 2 off and still can't get it to join. There isn't anything wrong with the internet connection because my laptop is still working just fine. Are there any other ideas on how to get this to connect?

I am having a similar issue. ipad was working fine last night but this morning will not connect to wifi network. wifi is okay as am using it on my laptop. I have turned router on/off dozens of times, have disconnected all cables, unplugged form power, reset my ipad to factory settings, deleted my network and set up again, still no luck, airplane mode is off etc etc. very annoying...

Why can't I access the internet from my ipad2

This problem started after the most recent update. Hotspot is on my iPhone4, carrier is Verizon. Did not have this problem before update. Do I need to restore iPad to original? What do you think?

personalities_233 wrote:
Hello, thanks for the help but it did not work. I wonder what the problem is? =/
What did not work?
Did the airport router you are trying to connect to not show up under the airport symbol in the menubar?
If it did show up, did it have any symbols by it like a padlock for instance?
In other words, exactly what did you do and exactly what did you experience?
If your Mac does not even list the router in the menubar under the icon/symbol (triangle with curved lines, supposed to appear to be radio waves radiating) then the router may have a setting set that does not allow it to be seen except to computers with MAC addresses that have been entered into it as allowable. If this is the case then your MAC address will have to be entered into the router's list. MAC stands for Media Access Control. "Mac" is the abbreviation for Macintosh.
The fact that you mention you have two new symbols in your menu bar suggests that someone has been playing with the computer and making changes that you are unaware of. If this is the case then there are many possibilities for problems.
The fact is, a Mac fresh out of the box will see any router within range and connect to it unless the router requires a password or the router has Access Control set such that it cannot be seen by a computer that does not exist in its 'OK' list. Since yours works at school, that rules out a hardware or problem or most software problems with your computer. But networking is complicated enough that you have to be quite specific when you try to tell others what you have tried and what results you got.

Trouble accessing the internet on a WRT54G wireless router

I’ve run into a problem setting up a wireless network at my friends’ house. The problem is accessing the internet from the wireless PC that has a WMP11 Wireless PCI Card to a WRT54G wireless router.
The wireless PC is running Windows XP and it sees and connects to the router with “excellent” signal strength but will not connect to the internet.
The router is currently set to WEP 128 bit encryption security. I’ve tried disabling the wireless security all together but when I do that the wireless PC no longer sees the router.
I have no trouble connection to the internet thru the wireless network I have set up at my house when I bring his computer there. But my router is an older Linksys 802.11b so maybe that’s why.
Anyone have any ideas what I should try other than telling him to buy a new wireless G adapter card?

If earlier your Wireless Adapter is working fine with the same network & computer .... try upgrading the drivers of the aqdapter .... from http://linksys.com/download .... uninstall the older drivers & reinstall newer drivers ....

Accessing the internet from flash player

Similar Messages

Maybe you are looking for