ACE 4710 Device Manager Gives Blank Screen

Hi Guys,
Wish somebody could share his/her experience on this.
I have a problem with ACE4710 Device Manager that after entering username and password, it will appear just a blank screen. And it happen also to the FT peer.
I know that the workaround is to reload the ACE (as it happened one time before) but I wish somebody could share a better or probably permanent solution to this problem.
Thank you in advance guys.
Tomy.

CSCsv95366: Device Manager displays a blank page after login
Upgrade to A3(2.2) or beyond.
Gilles.

Similar Messages

ACE-4710 : Device Manager on Primary ACE cannot authenticate

Hi,
In a cluster of redundant ACE-4710, version A5(1.2), the graphical Device Manager on the primary ACE cannot authenticate users. An error message is displayed :
The strange thing is that the standby ACE Device Manager work correctly. Moreover, both ACE are perfectly synchronized :
CH01AC03/P-115-A# sh ft group summary
FT Group                     : 14
Configured Status            : in-service
Maintenance mode             : MAINT_MODE_OFF
My State                     : FSM_FT_STATE_ACTIVE
My Config Priority           : 200
My Net Priority              : 200
My Preempt                   : Enabled
Peer State                   : FSM_FT_STATE_STANDBY_HOT
Peer Config Priority         : 150
Peer Net Priority            : 150
Peer Preempt                 : Enabled
Peer Id                      : 1
No. of Contexts              : 1
Here is the details on the ACE and DM version :
CH01AC03/P-115-A# sh ver
Cisco Application Control Software (ACSW)
TAC support: http://www.cisco.com/tac
Copyright (c) 1985-2012 by Cisco Systems, Inc. All rights reserved.
The copyrights to certain works contained herein are owned by
other third parties and are used and distributed under license.
Some parts of this software are covered under the GNU Public
License. A copy of the license is available at
http://www.gnu.org/licenses/gpl.html.
Software
loader:    Version 0.95.1
system:    Version A5(1.2) [build 3.0(0)A5(1.2) adbuild_19:38:58-2012/01/17_/auto/adbure_nightly4/renumber/rel_a5_1_2_throttle/REL_3_0_0_A5_1_2]
system image file: (hd0,1)/c4710ace-t1k9-mz.A5_1_2.bin
Device Manager version 5.1 (0) 20111215:1009
What coud be the problem ?
Thank you
Yves

Hello Yves,
Try with the command "dm reload" in the Admin Context
Cesar R
ANS Team

Startx & gdm give blank screen

I'd like to get GNOME installed for a GUI environment. Proving difficult. Anybody have any idea how to help me?
typing "startx" gives blank screen
setting "systemctl enable gdm" gives blank screen after boot
setting "systemctl start gdm" gives blank screen
I installed brand new Arch (2014.10.01) following the wiki step by step. Everything worked okay. So I set out to get gnome installed.
To install gnome, I installed:
xorg-server
xorg-xinit
xf86-video-intel
libva-intel-driver
libva
lib32-mesa-libgl (after uncommenting pacman.conf)
gnome (with all 1-40)
I tried adding "exec gnome-session" to the ~./xinitrc file and then rebooting but this did nothing.
Did I miss installing something? Some file need configuring?
By the way, how do I get internet at boot automatically without having to type "dhcpcd <ethernet-adapter-name here>" after every boot?

bzpnbx wrote:
I'd like to get GNOME installed for a GUI environment. Proving difficult. Anybody have any idea how to help me?
typing "startx" gives blank screen
setting "systemctl enable gdm" gives blank screen after boot
setting "systemctl start gdm" gives blank screen
I installed brand new Arch (2014.10.01) following the wiki step by step. Everything worked okay. So I set out to get gnome installed.
To install gnome, I installed:
xorg-server
xorg-xinit
xf86-video-intel
libva-intel-driver
libva
lib32-mesa-libgl (after uncommenting pacman.conf)
gnome (with all 1-40)
I tried adding "exec gnome-session" to the ~./xinitrc file and then rebooting but this did nothing.
Did I miss installing something? Some file need configuring?
By the way, how do I get internet at boot automatically without having to type "dhcpcd <ethernet-adapter-name here>" after every boot?
Not sure how to fix it, but you should need the base install, xorg-server, gnome, and I usually include the option xorg-server-utils but that shouldn't be needed?
At that point you should be able to enable/start GDM and if everything goes good it will work. Obviously not your case, I just say this to point out that so far your not wrong...
No idea on that one, but first I would be looking at making sure I had the right video drivers for xorg (see the xorg wiki page about identifying video card with 'lspci | grep -e VGA -e 3D' ), and look up the logs to see what X is actually doing and if its running and just outputing to the wrong display or if there are errors, ect...
Internet kind depends on how/what your trying to do, however in your case the most normal thing would likely be to install network manager, then you will probably also have to download a gnome network manager applet (I think its network-manager-applet)
This will give you the normal system tray icon to manage your network manager settings.
With only a command line I typically prefer wifi-menu for ease.

ACE30 - Accessing the ACE Applicance Device Manager

Hi...
I've got basic connectivty to our ACE30 module and when I try connecting to the management IP address (attached to the Admin context), I see a very basic GUI which only lists the CSM to ACE config conversion tool. I don't see a GUI as detailed in the document:
http://www.cisco.com/en/US/docs/app_ntwk_services/data_center_app_services/ace_appliances/vA1_7_/configuration/device_manager/guide/UG_over.html#wp1072950
How do I get the ACE Applicance Device Manager GUI working so that I can then configure real servers, serverfarms etc rather than via the GUI?
Having read through copious amount of documentation I can't seem to find a refrence that would help here. This should be a fairly straight forward exercise - do I need to install some other software to get the full fledged GUI working?
thanks
Sheldon

Only the ACE 4710 appliances have the GUI. If you are looking for a GUI for the ACE30 module you will need to use Cisco Application Network Manager (ANM) It will provide the GUI for the ACE30 to be able to configure it. As you have seen, only the conversion tool is available on the module.

After iOS7 upgrade, iTunes only gives blank screens. And Netflix won't load. Any idea on what to do?

After iOS7 upgrade, iTunes only gives blank screens. And Netflix won't load. Any idea on what to do?

Yep. I did some more poking around and found that one. Downloaded it and tried to run it and got more errors. Did some more searching and found a fix for the installer on Vista. Ran the fix and tried the ipod software again. It got further, but then hung up again. I'm still trying to figure this all out. Anyone got any answers it'd be much appreciated.

Device Manager is blank

Everything started when I tried to use a Huawei EC168 USB Stick to connect to the Internet. When it installs the program used to run this device into the computer, and tries to install the drivers for this purpose it installs everything but what I suppose is a driver named Data Interface. Then I figured this could be solved by using Device Manager, but to my surprise it appears to be blank. I have tried uninstalling everything and installing it again (even by making a System Restore), I've tried updating my computer, I tried solving it through "regedt32" and so on. Any ideas on how to solve this?

Hi Friend! I have never seen that before. I'm sorry, but I don't have any more suggestions for you. The only suggestion I have is restore back to factory. There may be more replies. I'm totally amazed. How can this be?? Could this be a Virus?? I don't know. A restore back to factory should get rid of a virus and give you a clean start. Save your important data on a external USB. I'm a little disturbed my self. I registered here to help owners of Toshiba lap tops and it seems that I have been left to answer all the messages with very little help and that is up setting. I just received a another promotion and that is a good thing????? I think ???I rely on what my inner self is telling me to reply. Some times I get it right. Some times I get it wrong. I'm thinking that I have probably forgot as much as I know and what I have learned. Your problem is some thing I have never encountered. Thank you for your reply and your feed back. I'm hoping others will reply latter.
Dokie!
http://support.toshiba.com/support/staticContentDetail?contentId=3438836&isFromTOCLink=false
PS Good night Vietnam!!
I Love my Satellite L775D-S7222 Laptop. Some days you're the windshield, Some days you're the bug. The Computer world is crazy. If you have answers to computer problems, pass them forward.

GE60 Wont Boot and F3 Recovery gives blank screen

Hi,
I purchased a MSI GE60 yesterday. On the second reboot the system said it was updating the system and during this time, the laptop went into sleep mode. Now every time I power up the laptop one of 2 things happens.
1) it gives me the MSI logo and the spinner for about 20 minutes then says it is repairing windows. Gets to about 6% after about a further 20 minutes and then turns off.
2) it gives me the MSI logo and the spinner for about 10 minutes and then powers off
In both cases the Blue Turbo light stays on all the time.
I have tried using the F3 Recovery. I get the MSI Logo and the spinner and a message saying it is preparing to repair windows. This lasts for about 10 seconds and then I get a blank screen. The screen stays blank for about 15 -20 minutes and then the laptop powers down.
Does anyone have any advice about how I can get the system recovery to work.

Quote from: prestondocks on 03-August-13, 22:27:05
Hi,
I purchased a MSI GE60 yesterday. On the second reboot the system said it was updating the system and during this time, the laptop went into sleep mode. Now every time I power up the laptop one of 2 things happens.
1) it gives me the MSI logo and the spinner for about 20 minutes then says it is repairing windows. Gets to about 6% after about a further 20 minutes and then turns off.
2) it gives me the MSI logo and the spinner for about 10 minutes and then powers off
In both cases the Blue Turbo light stays on all the time.
I have tried using the F3 Recovery. I get the MSI Logo and the spinner and a message saying it is preparing to repair windows. This lasts for about 10 seconds and then I get a blank screen. The screen stays blank for about 15 -20 minutes and then the laptop powers down.
Does anyone have any advice about how I can get the system recovery to work.
Hi!
I have a GE60 2oc and had the same problem and found out that it is because the notebook is delivered with nearly 30 language packs and at each restart windows remove 1 (ONE) language pack. I.e. it takes 30 restarts to get rid of all the unused language packs.
If you run lpksetup as administrator you can delete the language packs you do not need. However it do take a lot of time to do, but you get rid of them in one go!
Kurt

Clicking Google search results in a frame gives blank screen

The back story to this is that i use Firefox and I use a simple frames home page where my fave links(ebay,craigslist links mainly) are on the left frame of the screen and google opens up on the right frame. When I do a search with google it does what it does and gives me its search results. Normally when i click on one of the Google results the frame on the left stays and the right side goes to the link i clicked on. Not today though. All I get is a blank screen and Done in the status bar. The left frame is still there. This occurs on 2 computers. IE does not have a problem. Is it Google? Firefox? Or a combo of both?
Here's the code for my main frames page. I dont need to include the 2nd one.
1.htm
== This happened ==
Not sure how often
== May 25th, 2010

On this forum you need to use the HTML entity '''&lt;''' for "'''<'''" and '''&gt;''' for "'''>'''".
Use the CODE button after you have selected the text to put the text in a CODE block
A good place to ask questions and advice about web development is at the MozillaZine Web Development/Standards Evangelism forum.
The helpers at that forum are more knowledgeable about web development issues.
You need to register at the MozillaZine forum site in order to post at that forum.
See http://forums.mozillazine.org/viewforum.php?f=25

Device Manager window blank

I am running win 7 pro on X1 carbon. My device manager window is blank. No devices displayed. I ensured plug and play is set to automatic and all services are enabled. I also looked at my registery and ensured the proper permissions were set. I also update the BIOS. Running SP 1. Any ideas thank you

Hi stardrop,
Welcome to Apple Discussions
See if this link helps: iPod not recognized and Windows Device Manager is empty
Regards
Colin R.

Managing Subscription blank screen. When I click manage against any subscription it takes me to a blank screen

OK Had Dreamweaver and Indesign single programme subscriptions.
These were installed in an OLD pc and old laptop. Both machines developed faults that could not be fixed.
So I bought new PC and I am trying to manage subscriptions in adobe to download the programs and remove the old registrations.
Problem is that when I click manage subscriptions on
https://www.adobe.com/uk/account.html
I just go to a blank screen
So I cant update the subscription OR download the programe.
Win 7 machine. 16 GB. over 700 GB free on drive.

I had a problem with that page yesterday; it didn't fully load. Today it's fine.
If you still have problem, try using a different browser.

Air SDK version 15.0.0.249 gives blank screen

Hi Guys,
I really need your help.
I have been working on an Air ios app for the last months. I have build the app with 14.0.0.137 and that seems to work fine.
However today i upgraded to 15.0.0.249 and still it works fine in the Flash CC IDE.
But when I install in on an device the app installs allright but when I run the app all it shows me is a blank/white screen !
Any help is greatly appriciated..I am totally lost here.
Thanks in advance.
/Henry

If you read this long thread:
Need to submit iPad app today [HELP]
you'll see how you can get the command line that Flash Pro uses.
Back to your main issue here, what happens if you do a debug test movie, onto the device? Generally you only get blank screens if a script error happens, and doing a debug test might show what line is failing.

MSI K8N TV tuner card gives blank screen?

Now besides other problems, My TV tuner card, that has and still does , run perfectly normal in every other board I have. Abit KV8, KV8-Pro, and NF7S, gives me black blank screen after watching it for more than 5 minutes. I have never had any such problems before. I have read all support at Hauppage and found no mention of this problem.
When I take it out of this board and put it into another machine, it works perfect.
Help please.
MSI K8N Neo MS-7030
1.4 Bios
Radeon 9800
Corsair 3200XL and tried Muchkin Special222
Maxtor Diamond Plus
Hauppage TV Tuner Card
Win XP-Pro
All normal updates etc, graphics drivers, DX9c
Never had this many problems with a Mobo since using cheapo Elite MB.

I have been seeing some amazing video using my msi TV-Tuner card (older card) and HDTV S-video inputs from my digital HDTV cable box. I understand what SteveK is saying about how S-video is not capable of displaying 1080i, but dang it looks awesome using dscaler. I did some searching and this guys says:
A better solution is S-video. Almost all players have s-video output. S-video looks much better than composite video, and only slightly inferior to component video. Hook an s-video cable from the player to the display (or to an A/V receiver that can switch s-video). The round, 4-pin connectors may be labelled Y/C, s-video, or S-VHS.
Link found here: http://www.home-theater-faq.com/whats_the_difference_between_composite_s-video_component_and_rgb_video.htm
Anyway I found some similar links that said about the same. In any case, if anyone wants to play with the HDTV viewing using dscaler and an HDTV s-video connection, it might be of interest.

Some odd warnings and messages for my Helix in the Lenovo Device Manager "Check Up" screen

If I open up the Lenovo Solution Center software, and go to the Check Up tab and select Device Manager, it shows a warning that says "One or more devices have problems", and lists two drivers that show "Unknown device" with a status of "Not installed".
There's no other information and I'm not sure what to make of this. Does anyone else have this issue? If I open up the Windows 8 Device Manager and expand all nodes in the tree, I don't see any devices with warning icons.
Also if I go back to the Hardware Scan button in the Check Up tab, and run it, althought he scan passes, it shows a Warning for the SMART short self test, and notes that the test is "Not supported", with a result code of WHD01V000-WIVZ2I. Is this anything to be concerned about? Note that it's not a failure, but a non supported test. Does anyone else's Helix complete this test?

I have the exact same problem with regard to 2 unknown devices not installed. I got the message after first getting the Helix and running the updates. I called Lenovo support and the tech could not figure it out and her response was "Well if is not causing any problems, I would not worry about it" which sounds like an excuse to just get me off the line. I was in a hurry to get somewhere and so did not push the issue.
The message only says 2 divices not installed, but does not tell you which ones. The tech said that if it was a real problem, the message would tell me what divices are not loaded.
I have seen another post or two from people with the same issue but not suggested fixes.

Transaction launcher gives blank screen

Hii All
I have configured a TL to launch Tx. - crmd_order(CRM) but it displays a blank screen.
I have already tried the following (by referring to SDN posts) :-
1. Notes 1620007 and 1521043 are already implemented in our system.
2. Maintained proper URL in CRMS_IC_CROSS_SYS. It is wokring fine when opened directly in IE.
3. Activated and tested the relevant ITS services (SICF).
4. In sicf service, the SAP implementation area is selected as "Signature Design" ( from the posts i found that if thevalue is "Netweaver Classic" then the blank screen issue comes).
5. Executed the report to publish ITS services : SIAC_PUBLISH_ALL_INTERNAL.
6. Executed BOR object in swo1. It is wokring fine.
But it still displays the blank screen. Please suggest some solution or the step which I am missing.
Thanks in advance.
Shafali

Hi Shafali,
You can find the detailed steps of implementation here:
[http://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/3059fb20-987f-2e10-ef82-d147b9b5e8b4?QuickLink=index&overridelayout=true|http://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/3059fb20-987f-2e10-ef82-d147b9b5e8b4?QuickLink=index&overridelayout=true]
Regards
Leon

Full Screen gives blank screen

Hi,
When I click the Display Full Screen button on any site, such as YouTube, I get a full blank white screen, and still have the audio playing. Pressing Esc returns to regular display. How can I get the Full Screen to work?
I have:
XP
IE8
Flash Player 10.2
Thanks,
Mike

Hi mikeytexas, I love it!! You solved your own problem. Great advice by the way
Glad you posted and especially your solution!!!
Regards,
eidnolb

ACE 4710 Device Manager Gives Blank Screen

Similar Messages

Maybe you are looking for