ACE 4710 - serverfarm predictor
Hi, I have a pair of ACE 4710 running in failover bundle and I have a number of server farms configured on them. For one of the server farm I'd like to use a different predictor than round robin. I have two real servers members of the server farm. Usually I do select predictor round robin and put both real servers in service. In this situation I need to have only one server as active and the 2nd one to be in standby and take over when the first one is down. I have tried to put the 2nd server in standby and when I shut down the primary the 2nd one won't become active. I do have a health probe to check for the status of the server so I thought this would be enough to detect the status of the server. So my question is , how can I configure the ACE to have one server as active and the second as a backup and this second one to take traffic only when the primary is down. Thank you, Florin.
Hi,
There are a couple of ways of achieving your objective.
The first method works for the simple case of two servers:
serverfarm host FARM-Redacted
probe PROBE-Redacted
rserver am03
backup-rserver am04
inservice
rserver am04
inservice standby
or you could use two serverfarms:
serverfarm host FARM-Redacted-Pri
description Redacted Serverfarm Primary
probe PROBE-Redacted
rserver am03
inservice
serverfarm host FARM-Redacted-Sec
description Redacted Serverfarm Secondary
probe PROBE-Redacted
rserver am04
inservice
policy-map type loadbalance first-match LB-POLICY-443
class class-default
serverfarm FARM-Redacted-Pri backup FARM-Redacted-Sec
HTH
Cathy
Similar Messages
-
Need help to Configure Cisco ACE 4710 Cluster Deployment
Dear Experts,
I'm newbie for Cisco ACE 4710, and still I'm in learning stage. Meanwhile I got chance at my work place to deploy a Cisco ACE 4710 cluster which should load balance the traffic between two Application Servers based on HTTP and HTTPS traffic. So I was looking for good deployment guide in Cisco SBA knowledge base then finall found this guide.
http://www.cisco.com/en/US/docs/solutions/SBA/February2013/Cisco_SBA_DC_AdvancedServer-LoadBalancingDeploymentGuide-Feb2013.pdf
This guide totally fine with my required deployment model. I have same deployment environment as this guide contains with ACE cluster that connects to two Cisco 3750X (Stack) switches. But I have some confusion places in this guide
This guide follow the "One-armed mode" as a deployment method. But when I go through it further I have noticed that they have configured server VLAN as a 10.4.49.0/24 (all servers reside in it) and Client side VIP also in same VLAN which is 10.4.49.100/24 (even NAT pool also).
My confusion is, as I have learned about Cisco ACE 4710 one-armed mode deployment method, it should has two VLAN segments, one for Client side which client request come and hit the VIP and then second one for Server side. which means besically two VLANs. So please be kind enough to go through above document then tell me where is wrong, what shoud I need to do for the best. Please this is an urgent, so need your help quickly.
Thanks....!
-Amal-Dear Kanwal,
I need quick help for you. Following are the Application LB requirements which I received from my clinet side.
Following detail required for configuring Oracle EBS Apps tier on HA:
LBR IP and Name required to configure EBS APPS Tier (i.e, ap1ebs & ap2ebs nodes)
Suggested IP and Name for LBR:
IP : 172.25.45.x [should be on same 172.25.45 subnet of ap1ebs & ap2ebs nodes]
ebiz.xxxx.lk [on port 80 for http protocol accessibility]
This LBR IP & name must be resolve and respond on DNS network
Server Farm detail for LBR Setup
Following detail will be use for configuring the LBR:
LBR IP and Name :
IP : 172.25.45.x [should be on same 172.25.45 subnet of ap1ebs & ap2ebs nodes]
ebiz.xxxx.lk [on port 80 for http protocol accessibility]
This LBR IP & name must be resolve and respond on DNS network
Server Farm Detail for LBR setup:
Server 1 (EBS App1 Node, ap1ebs):
IP : 172.25.45.19
Server Name: ap1ebs.xxxx.lk [ap1ebs hostname is an example, actual hostname will be use]
Protocol: http
Port: 8000
Server 2 (EBS App2 Node, ap2ebs):
IP : 172.25.45.20
Server Name: ap2ebs.xxxx.lk [ap2ebs hostname is an example, actual hostname will be use]
Protocol: http
Port: 8000
Since my client needs to access URL ebiz.xxxx.lk which should be resolved by IP 172.25.45.21 (virtual IP) via http (80) before they deploy the app on the two servers I just ran web service on both servers (Linux) and was trying to access http://172.25.45.21 it was working fine and gave me index.html page. Now after my client has deployed the application then when he tries to access the page http://172.25.45.21 he cannot see his main login page. But still my testing web servers are there on both servers when I type http://172.25.45.21 it will get index.html page, but not my client web login page. What can I do for this ?
Following are my latest config :
probe http Get-Method
description Check to url access /OA_HTML/OAInfo.jsp
interval 10
faildetect 2
passdetect interval 30
request method get url /OA_HTML/OAInfo.jsp
expect status 200 200
probe udp http-8000-iRDMI
description IRDMI (HTTP - 8000)
port 8000
probe http http-probe
description HTTP Probes
interval 10
faildetect 2
passdetect interval 30
passdetect count 2
request method get url /index.html
expect status 200 200
probe https https-probe
description HTTPS traffic
interval 10
faildetect 2
passdetect interval 30
passdetect count 2
ssl version all
request method get url /index.html
probe icmp icmp-probe
description ICMP PROBE FOR TO CHECK ICMP SERVICE
rserver host ebsapp1
description ebsapp1.xxxx.lk
ip address 172.25.45.19
conn-limit max 4000000 min 4000000
probe icmp-probe
probe http-probe
inservice
rserver host ebsapp2
description ebsapp2.xxxx.lk
ip address 172.25.45.20
conn-limit max 4000000 min 4000000
probe icmp-probe
probe http-probe
inservice
serverfarm host ebsppsvrfarm
description ebsapp server farm
failaction purge
predictor response app-req-to-resp samples 4
probe http-probe
probe icmp-probe
inband-health check log 5 reset 500
retcode 404 404 check log 1 reset 3
rserver ebsapp1 80
conn-limit max 4000000 min 4000000
probe icmp-probe
inservice
rserver ebsapp2 80
conn-limit max 4000000 min 4000000
probe icmp-probe
inservice
sticky http-cookie jsessionid HTTP-COOKIE
cookie insert browser-expire
replicate sticky
serverfarm ebsppsvrfarm
class-map type http loadbalance match-any default-compression-exclusion-mime-type
description DM generated classmap for default LB compression exclusion mime types.
2 match http url .*gif
3 match http url .*css
4 match http url .*js
5 match http url .*class
6 match http url .*jar
7 match http url .*cab
8 match http url .*txt
9 match http url .*ps
10 match http url .*vbs
11 match http url .*xsl
12 match http url .*xml
13 match http url .*pdf
14 match http url .*swf
15 match http url .*jpg
16 match http url .*jpeg
17 match http url .*jpe
18 match http url .*png
class-map match-all ebsapp-vip
2 match virtual-address 172.25.45.21 tcp eq www
class-map type management match-any remote_access
2 match protocol xml-https any
3 match protocol icmp any
4 match protocol telnet any
5 match protocol ssh any
6 match protocol http any
7 match protocol https any
8 match protocol snmp any
policy-map type management first-match remote_mgmt_allow_policy
class remote_access
permit
policy-map type loadbalance first-match ebsapp-vip-l7slb
class default-compression-exclusion-mime-type
serverfarm ebsppsvrfarm
class class-default
compress default-method deflate
sticky-serverfarm HTTP-COOKIE
policy-map multi-match int455
class ebsapp-vip
loadbalance vip inservice
loadbalance policy ebsapp-vip-l7slb
loadbalance vip icmp-reply active
nat dynamic 1 vlan 455
interface vlan 455
ip address 172.25.45.36 255.255.255.0
peer ip address 172.25.45.35 255.255.255.0
access-group input ALL
nat-pool 1 172.25.45.22 172.25.45.22 netmask 255.255.255.0 pat
service-policy input remote_mgmt_allow_policy
service-policy input int455
no shutdown
ft interface vlan 999
ip address 10.1.1.1 255.255.255.0
peer ip address 10.1.1.2 255.255.255.0
no shutdown
ft peer 1
heartbeat interval 300
heartbeat count 10
ft-interface vlan 999
ft group 1
peer 1
no preempt
priority 110
associate-context Admin
inservice
ip route 0.0.0.0 0.0.0.0 172.25.45.1
Hope you will reply me soon
Thanks....!
-Amal- -
Using the ACE 4710 for loadbalancing a Sharepoint site.
We currently have a HTTP probe setup to check the port 80 status of the rserver.
Is there anyway to get the HTTP probe to check a DNS entry for each of the application sites? For instance http://info vs http://site are two different web sites running on the same IP. One site could have a problem but the actual port 80 for the IP may be still alive.
Thanks for any information.Has anyone figure this out? I am tring to get healthchecks/probes setup in this same fashion. I have 2 servers with 1 IP but have many sites. I want to probe each side and ensure I get a 200 code. I also have to provide credentials to the site. It seems that if i open IE I can log in just fine to the site with the credentials. However there is an active x control box that is wanting to be installed. When I set this up on my ACE it seems I am getting a http 401 unauthorized error. I have done a wireshark capture while I was browsing and I see the 401 however it also reports a 200 code after that. Do you think this is a problem because of the active x control wanting to be downloaded? Or is this an issue with the first http code that is recieved by the probe, that being the 401 and then the 200? Below is my config (cleaned of course).
probe http HTTP-80-OUR.DOMAIN.COM
interval 15
passdetect interval 60
credentials
request method get url http://our.domain.com/default.aspx
expect status 200 200
header Host header-value "our.domain.com"
open 1
rserver host SERVER-A
ip address X.X.X.47
inservice
rserver host SERVER-B
ip address X.X.X.48
inservice
serverfarm host FARM-AB
predictor leastconns
probe HTTP-80-OUR.DOMAIN.COM
rserver SERVER-A
inservice
rserver SERVER-B
inservice
ACE4710# show probe HTTP-80-OUR.DOMAIN.COM detail
probe : HTTP-80-OUR.DOMAIN.COM
type : HTTP
state : ACTIVE
description :
port : 80 address : 0.0.0.0 addr type : -
interval : 15 pass intvl : 60 pass count : 3
fail count: 3 recv timeout: 10
http method : GET
http url : http://our.domain.com
conn termination : GRACEFUL
expect offset : 0 , open timeout : 1
expect regex : -
send data : -
------------------ probe results ------------------
associations ip-address port porttype probes failed passed health
------------ ---------------+-----+--------+--------+--------+--------+------
serverfarm : OUR.DOMAIN.COM-10.25.4.12-L3-FARM
real : SERVER-A[0]
X.X.X.47 80 DEFAULT 414 406 8 FAILED
Socket state : CLOSED
No. Passed states : 1 No. Failed states : 2
No. Probes skipped : 0 Last status code : 401
No. Out of Sockets : 0 No. Internal error: 0
Last disconnect err : Received invalid status code
Last probe time : Wed Jun 2 17:44:18 2010
Last fail time : Wed Jun 2 13:37:04 2010
Last active time : Wed Jun 2 13:34:19 2010
real : SERVER-B[0]
X.X.X.48 80 DEFAULT 414 406 8 FAILED
Socket state : CLOSED
No. Passed states : 1 No. Failed states : 2
No. Probes skipped : 0 Last status code : 401
No. Out of Sockets : 0 No. Internal error: 0
Last disconnect err : Received invalid status code
Last probe time : Wed Jun 2 17:44:20 2010
Last fail time : Wed Jun 2 13:37:06 2010
Last active time : Wed Jun 2 13:34:21 2010 -
ACE 4710 - Internet Explorer cannot display the webpage randomly
We have a ACE 4710 with a basic config, (see below).
When clicking on a tab from a window within Interent explorer we occasionally get an issue with it returning: "Internet Explorer cannot display the webpage" The details show "Access is denied" accessing a particular line of a javascript file.
We have put one web server out of service in the farm to make sure that this isn't a result of stickyness not quite working.
We have tested extensively by going directly to the web server directly without the load balancer and cannot reproduce the problem but we can produce the issue within a few minutes when going to the load balanced address.
Thanks in advance for any advice.
HOST-1/Admin# show run
Generating configuration....
logging enable
logging fastpath
logging standby
logging timestamp
logging trap 6
logging history 6
resource-class SLB_ResourceClass_T_R
limit-resource all minimum 10.00 maximum unlimited
resource-class sticky
limit-resource all minimum 10.00 maximum unlimited
boot system image:c4710ace-t1k9-mz.A5_1_2.bin
peer hostname HOST-2
hostname HOST-1
interface gigabitEthernet 1/1
switchport access vlan 1000
no shutdown
interface gigabitEthernet 1/2
shutdown
interface gigabitEthernet 1/3
description LB003
switchport access vlan 1
shutdown
interface gigabitEthernet 1/4
description LB004
switchport access vlan 2
shutdown
interface port-channel 1
port-channel load-balance src-dst-port
no shutdown
clock timezone standard GMT
switch-mode
context Admin
description SUTLB01
member SLB_ResourceClass_T_R
access-list ALL line 8 extended permit ip any any
access-list ALL line 16 extended permit icmp any any
access-list everyone line 8 extended permit ip any any
access-list everyone line 16 extended permit icmp any any
probe tcp probe_tcp_80
port 80
rserver host Server_S_W301
description Server_S_W301
ip address x.x.32.152
inservice
rserver host Server_S_W302
description Server_S_W302
ip address x.x.32.154
inservice
serverfarm host sfarm_T_R
description sfarm_T_R
predictor leastconns
probe probe_tcp_80
rserver Server_S_W301 80
rserver Server_S_W302 80
inservice
sticky http-cookie Cookie1 T_R_sticky_cookie
cookie insert browser-expire
timeout 3600
serverfarm sfarm_T_R
class-map match-any T_R_L4Class
2 match virtual-address x.x.33.150 tcp eq www
class-map type management match-any remote_access
2 match protocol xml-https any
3 match protocol icmp any
4 match protocol telnet any
5 match protocol ssh any
6 match protocol http any
7 match protocol https any
8 match protocol snmp any
policy-map type management first-match remote_mgmt_allow_policy
class remote_access
permit
policy-map type loadbalance first-match T_R_L7policy
class class-default
sticky-serverfarm T_R_sticky_cookie
policy-map multi-match T_R_L4Policy
class T_R_L4Class
loadbalance vip inservice
loadbalance policy T_R_L7policy
loadbalance vip icmp-reply active
nat dynamic 2 vlan 1000
interface vlan 1000
ip address x.x.33.148 255.255.254.0
access-group input ALL
nat-pool 2 x.x.33.151 x.x.33.151 netmask 255.255.254.0 pat
service-policy input remote_mgmt_allow_policy
service-policy input T_R_L4Policy
no shutdown
ip route 0.0.0.0 0.0.0.0 x.x.32.1
ssh key rsa 1024 force+------------------------------------------+
+-------------- HTTP statistics -----------+
+------------------------------------------+
LB parse result msgs sent : 421347 , TCP data msgs sent : 2099597
Inspect parse result msgs : 0 , SSL data msgs sent : 0
sent
TCP fin msgs sent : 6169 , TCP rst msgs sent: : 769
Bounced fin msgs sent : 5 , Bounced rst msgs sent: : 1
SSL fin msgs sent : 0 , SSL rst msgs sent: : 0
Drain msgs sent : 337811 , Particles read : 5040829
Reuse msgs sent : 0 , HTTP requests : 342499
Reproxied requests : 183422 , Headers removed : 37475
Headers inserted : 342124 , HTTP redirects : 0
HTTP chunks : 224859 , Pipelined requests : 71466
HTTP unproxy conns : 267246 , Pipeline flushes : 0
Whitespace appends : 0 , Second pass parsing : 0
Response entries recycled : 71302 , Analysis errors : 0
Header insert errors : 22 , Max parselen errors : 215
Static parse errors : 99 , Resource errors : 0
Invalid path errors : 0 , Bad HTTP version errors : 0
Headers rewritten : 0 , Header rewrite errors : 0
SSL headers inserted : 0 , SSL header insert errors : 0
SSL spoof headers deleted : 0 , Unproxy msgs sent : 267246
HTTP passthrough stat : 0
NOTE - We did turn on caching at one point to try and resolve the issue but it has since been turned off -
ACE 4710 transparent LB with two Caches and two routers.
Hello,
I have ACE 4710 that load balance two cach flows (bluecoat), i am doing pbr on the routers to send the traffic destined to port 80 to ACE then Cach farm. After that the Cach flow will get the page from the internet via two routers. The return traffic will match another pbr on the routers with source port 80 that will send it to the ACE then CachFlow again .....then to the users.
I am not using ip-spoofing on the CachFlow for now. In the figure attached i created a VIP 0.0.0.0 0.0.0.0 port 80 on the interface on the ACE facing the routers, but the question is do i have to create another VIP 0.0.0.0 0.0.0.0 port 80 on the interface on ACE facing the Cach Flow? or just forward the traffic on the default route? What might be the default route since i have to use two routers and i cannot use hsrp?
Kindly I need some assistance
Thank you and regards,
George
access-list PERMIT_ALL line 8 extended permit ip any any
access-list CFLOW line 8 extended permit ip any any
ip name-server 8.8.8.8
ip name-server 4.2.2.2
##################################Config for Cache Cache Servers###################
probe http CISCO_WWW_PROBE
ip address 72.163.4.161
interval 2
faildetect 2
passdetect interval 2
passdetect count 5
request method head url /index.html
expect status 200 200
exit
probe http YAHOO_WWW_PROBE
ip address 87.248.112.181
interval 2
faildetect 2
passdetect interval 2
passdetect count 5
request method head url /index.html
expect status 200 200
exit
serverfarm host TRANSPARENT_PROXY_SF
description Transparent Proxy Farm
transparent
predictor hash url
probe CISCO_WWW_PROBE
probe YAHOO_WWW_PROBE
rserver CFLOW01
inservice
rserver CFLOW02
inservice
exit
exit
############################################# Router Cache Farm ############################
probe icmp ICMP_PROBE
description *** Probe for icmp health monitoring ***
interval 5
faildetect 2
passdetect interval 60
passdetect count 2
exit
rserver host Router01
description Connection to Sodetel Router
ip address 192.168.14.4
probe ICMP_PROBE
inservice
rserver host Router02
description Connection to IDM Router
ip address 192.168.14.5
probe ICMP_PROBE
inservice
serverfarm host Routers
description Transparent Proxy Farm
transparent
predictor hash url
probe ICMP_PROBE
rserver Router01
inservice
rserver Router02
inservice
exit
exit
################################# Management################################
class-map type management match-any REMOTE_MGMT
description Allow Remote management for below protocols
8 match protocol icmp any
9 match protocol ssh source-address 172.31.13.31 255.255.255.255
10 match protocol ssh source-address 172.31.31.21 255.255.255.255
policy-map type management first-match REMOTE_MGMT_ALLOW_POLICY
class REMOTE_MGMT
permit
class-map match-all CFLO2Internet
2 match virtual-address 0.0.0.0 0.0.0.0 any
class-map match-all TRANSPARENT_VIP_CM
2 match virtual-address 0.0.0.0 0.0.0.0 tcp eq www
policy-map type loadbalance first-match TRANSPARENT_LB_PM
class class-default
serverfarm TRANSPARENT_PROXY_SF backup Routers
policy-map type loadbalance first-match CFLO2Internet_LB
class class-default
serverfarm Routers
policy-map multi-match CFLO2Internet_PM
class CFLO2Internet
loadbalance vip inservice
loadbalance policy CFLO2Internet_LB
loadbalance vip icmp-reply active
connection advanced-options TCP
policy-map multi-match L3L4_PM
class TRANSPARENT_VIP_CM
loadbalance vip inservice
loadbalance policy TRANSPARENT_LB_PM
loadbalance vip icmp-reply active
connection advanced-options TCP
====Interfaces======
interface vlan 11
description Interface between Routers and ACE
ip address 192.168.14.2 255.255.255.224
alias 192.168.14.1 255.255.255.224
peer ip address 192.168.14.3 255.255.255.224
no icmp-guard
access-group input PERMIT_ALL
service-policy input REMOTE_MGMT_ALLOW_POLICY
service-policy input L3L4_PM
no shutdown
interface vlan 21
description Connection to CFlow ServerFarm
ip address 192.168.12.2 255.255.255.224
alias 192.168.12.1 255.255.255.224
peer ip address 192.168.12.3 255.255.255.224
no icmp-guard
access-group input CFLOW
service-policy input CFLO2Internet_PM ------>>>> Is this necessary???
no shutdownHi George,
In the topology you described, only the service-policy in the interface towards the routers is necessary. For the traffic from the caches, the ACE will just forward to the default gateway.
The only problem is, as you mentioned, that you cannot use HSRP. In that case, you can still configure two default gateways, but there is no way to predict which one the ACE will use at a given time (the way it does to select the one it will use is sending an ARP request to both gateways and using the one that replies first until the ARP entry expires)
If you need to load-balance the traffic between both routers, then yes, you would need to configure a new VIP on the cache side and load-balanced to a transparent serverfarm composed of both routers.
Regards
Daniel -
ACE 4710: Find out the response time of a real server
Hi to everyone,
I have a couple of ACE 4710 and I need to find out what is the response time of a real server.
Is there a way for this?
Thank you for any answer!
giorgio romanoHi,
Kindly add the following line in your serverfarm configuration:
predictor response syn-to-synack
Suppose your serverfarm looks like this:
serverfarm host AAA_FARM
predictor response syn-to-synack
probe HTTP_PROBE
probe TCP9001_PROBE
rserver SC106
inservice
rserver SC107
inservice
rserver SC108
inservice
rserver SC109
inservice
rserver SC110
inservice
rserver SC111
inservice
rserver SC112
inservice
rserver SC113
inservice
rserver SC114
inservice
rserver SC120
inservice
rserver SC131
inservice
And then use the following command to see the average response time from your rserver as follows:
ACE1/prod# show serverfarm AAA_FARM detail
serverfarm : AAA_FARM, type: HOST
total rservers : 11
active rservers: 11
description : ServerFarm AAA
state : ACTIVE
predictor : RESPONSE
method : syn-to-synack
samples : 8
failaction : -
back-inservice : 0
partial-threshold : 0
num times failover : 0
num times back inservice : 0
total conn-dropcount : 0
Probe(s) :
HTTP_PROBE, type = HTTP
TCP9001_PROBE, type = TCP
----------connections-----------
real weight state current total failures
---+---------------------+------+------------+----------+----------+---------
rserver: SC106
x.x.x.x.:0 8 OPERATIONAL 2 1125 0
max-conns : 4000000 , out-of-rotation count : 0
min-conns : 4000000
conn-rate-limit : - , out-of-rotation count : -
bandwidth-rate-limit : - , out-of-rotation count : -
retcode out-of-rotation count : -
load value : 0
average response time (usecs) : 81 ----> thats what you might be looking for
From other day :
rserver: SC114
x.x.x.x:0 8 OPERATIONAL 70 10903 2
max-conns : 4000000 , out-of-rotation count : 0
min-conns : 4000000
conn-rate-limit : - , out-of-rotation count : -
bandwidth-rate-limit : - , out-of-rotation count : -
retcode out-of-rotation count : -
load value : 0
average response time (usecs) : 1334 ----> thats what you might be looking for
For Serverfarm BBB_FARM
serverfarm : BBB_FARM, type: HOST
total rservers : 1
active rservers: 1
description : ServerFarm BBB
state : ACTIVE
predictor : RESPONSE
method : syn-to-synack
samples : 8
failaction : -
back-inservice : 0
partial-threshold : 0
num times failover : 1
num times back inservice : 1
total conn-dropcount : 0
Probe(s) :
----------connections-----------
real weight state current total failures
---+---------------------+------+------------+----------+----------+---------
rserver: SC208
x.x.x.x:0 8 OPERATIONAL 0 0 0
max-conns : 4000000 , out-of-rotation count : 0
min-conns : 4000000
conn-rate-limit : - , out-of-rotation count : -
bandwidth-rate-limit : - , out-of-rotation count : -
retcode out-of-rotation count : -
load value : 0
average response time (usecs) : 0 ----> thats what you might be looking for
Use more detials for response predictor:
http://www.cisco.com/en/US/docs/app_ntwk_services/data_center_app_services/ace_appliances/vA3_1_0/configuration/slb/guide/rsfarms.html#wp1068831
Configuring the Application Response Predictor
To instruct the ACE to select the server with the lowest average response time for the specified response-time measurement based on the current connection count and server weight (if configured), use the predictor response command in server farm host or redirect configuration mode. This predictor is considered adaptive because the ACE continuously provides feedback to the load-balancing algorithm based on the behavior of the real server.
To select the appropriate server, the ACE measures the absolute response time for each server in the server farm and averages the result over a specified number of samples (if configured). With the default weight connection option configured, the ACE also takes into account the server's average response time and current connection count. This calculation results in a connection distribution that is proportional to the average response time of the server.
The syntax of this command is as follows:
predictor response {app-req-to-resp | syn-to-close | syn-to-synack}[samples number]
The keywords and arguments are as follows:
•app-request-to-resp—Measures the response time from when the ACE sends an HTTP request to a server to the time that the ACE receives a response from the server for that request.
•syn-to-close—Measures the response time from when the ACE sends a TCP SYN to a server to the time that the ACE receives a CLOSE from the server.
•syn-to-synack—Measures the response time from when the ACE sends a TCP SYN to a server to the time that the ACE receives the SYN-ACK from the server.
•samples number—(Optional) Specifies the number of samples over which you want to average the results of the response time measurement. Enter an integer from 1 to 16 in powers of 2. Valid values are 1, 2, 4, 8, and 16. The default is 8.
For example, to configure the response predictor to load balance a request based on the response time from when the ACE sends an HTTP request to a server to when the ACE receives a response back from the server and average the results over four samples, enter:
host1/Admin(config)# serverfarm SFARM1
host1/Admin(config-sfarm-host)# predictor response app-req-to-resp
samples 4
To reset the predictor method to the default of round-robin, enter:
host1/Admin(config-sfarm-host)# no predictor
To configure an additional parameter to take into account the current connection count of the servers in a server farm, use the weight connection command in server farm host predictor configuration mode. By default, this command is enabled. The syntax of this command is as follows:
weight connection
For example, enter:
host1/Admin(config)# serverfarm SF1
host1/Admin(config-sfarm-host)# predictor response app-request-to-resp
samples 4
host1/Admin(config-sfarm-host-predictor)# weight connection
To remove the current connection count from the calculation of the average server response time, enter:
host1/Admin(config-sfarm-host-predictor)# no weight connection
You can use threshold milliseconds parameter which is optional Specifies the required minimum average response time for a server. If the server response time is greater than the specified threshold value, the ACE removes the server from the load-balancing decision process (takes the server out of service).
Enter an integer from 1 to 300000 milliseconds (5 minutes). The default is no threshold (servers are not taken out of service).
In case if you have measures the response time from when the ACE sends a TCP SYN to a server to the time that the ACE receives a CLOSE from the server use syn-to-close (already discussed previously)
If you have to measures the response time from when the ACE sends a TCP SYN to a server to the time that the ACE receives the SYN-ACK from the server use syn-to-synack (already discussed previously)
SAMPLES parameter is optional and specifies the number of samples that you want to average from the results of the response time measurement and response time is used to select the server with the lowest response time for the requested response-time measurement. If you do not specify a response-time measurement method, the ACE uses the HTTP app-req-to-response method.
Whenever a server's load reaches zero, by default, the ACE uses the autoadjust feature to assign a maximum load value of 16000 to that server to prevent it from being flooded with new incoming connections. The ACE periodically adjusts this load value based on feedback from the server's SNMP probe and other configured options.
Using the least-loaded predictor with the configured server weight and the current connection count option enabled, the ACE calculates the final load of a real server as follows:
final load = weighted load × static weight × current connection count
where:
•weighted load is the load reported by the SNMP probe
•static weight is the configured weight of the real server
•current connection count is the total number of active connections to the real server
The ACE recalculates the final load whenever the connection count changes, provided that the (config-sfarm-host-predictor) weight connection command is configured. If the (config-sfarm-host-predictor) weight connection command is not configured, the ACE updates the final load when the next load update arrives from the SNMP probe.
If two servers have the same lowest load (either zero or nonzero), the ACE load balances the connections between the two servers in a round-robin manner.
HTH
Plz rate if u find it useful.
Sachin -
ACE 4710: Possible to allow a user to clear counters but nothing else?
Hello all,
Using an ACE 4710 we have a user setup with the Network-Monitor role which allows the user to view config, interface status, etc. We would also like to allow this user to clear the interface error counters as well, but nothing else. Is this possible?
Thanks!Hello Brandon-
Network-Monitor only lets you browse outputs, it is a not a role that allows a user to make any changes including clearing stats. You can create custom roles and domains to get closer to what you want, but you cannot zero in on a single command like that.
i.e.
ACE# conif t
ACE(config)# role MyRole
ACE(config-role)# rule 1 permit modify feature ?
AAA AAA related commands
access-list ACL related commands
connection TCP/UDP related commands
fault-tolerant Fault tolerance related commands
inspect Appln inspection related commands
interface Interface related commands
loadbalance Loadbalancing policy and class commands
pki PKI related commands
probe Health probe related commands
rserver Real server related commands
serverfarm Serverfarm related commands
ssl SSL related commands
sticky Sticky related commands
vip Virtual server related commands
You can create a permit or deny rule, within that, create/debug/modify/monitor each feature seperately.
Domains allow you to create containers for objects. You can place specific rservers, serverfarms, etc. into it - then apply it to a role so that the user assigned to it can only touch those objects.
Regards,
Chris Higgins -
ACE 4710 in bridge mode not working
I am trying to configure ACE 4710 bridge mode and I am stuck up in physical interface configuration. I have configured gig1/2 of ACE as trunk port and on layer 2 switch I have assigned that interface (gig1/2) to VLAN 11. I tried trunk port also but it got disabled due to BPDU error.
I am not able to ping servers as well as gateway. Below are the topology and context configuration:
Router (vlan 13: IP 172.16.11.254)
|
ACE (int gig1/2)
|
L2 Switch
|
Servers (vlan 11: IP 172.16.11.1 and 11.2)
Admin Context
===========
resource-class rc1
limit-resource all minimum 0.00 maximum unlimited
limit-resource sticky minimum 0.20 maximum unlimited
boot system image:c4710ace-mz.A3_2_4.bin
interface gigabitEthernet 1/1
switchport access vlan 1000
no shutdown
interface gigabitEthernet 1/2
switchport trunk allowed vlan 11,13
no shutdown
interface gigabitEthernet 1/3
shutdown
interface gigabitEthernet 1/4
shutdown
access-list ALL line 8 extended permit ip any any
access-list everyone line 8 extended permit ip any any
access-list everyone line 16 extended permit icmp any any
class-map type management match-any remote_access
2 match protocol xml-https any
3 match protocol icmp any
4 match protocol telnet any
5 match protocol ssh any
6 match protocol http any
7 match protocol https any
8 match protocol snmp any
policy-map type management first-match remote_mgmt_allow_policy
class remote_access
permit
interface vlan 1000
ip address 172.16.16.16 255.255.255.0
access-group input ALL
service-policy input remote_mgmt_allow_policy
no shutdown
ip route 0.0.0.0 0.0.0.0 172.16.16.254
context test
allocate-interface vlan 11
allocate-interface vlan 13
member rc1
test Context
=========
access-list bpdu-fixup ethertype permit bpdu
access-list ALL line 8 extended permit ip any any
access-list ALL line 16 extended permit icmp any any
rserver host srv1
ip address 172.16.11.1
inservice
rserver host srv2
ip address 172.16.11.2
inservice
serverfarm host srv
rserver srv1
inservice
rserver srv2
inservice
sticky ip-netmask 255.255.255.255 address both SG1
timeout 120
serverfarm srv
class-map type management match-any remote-mgmt
201 match protocol snmp any
202 match protocol ssh any
203 match protocol icmp any
204 match protocol http any
205 match protocol https any
206 match protocol xml-https any
class-map match-all slb-vip
2 match virtual-address 172.16.11.10 any
policy-map type management first-match remote-mgmt
class remote-mgmt
permit
policy-map type loadbalance first-match slb
class class-default
sticky-serverfarm SG1
policy-map multi-match client-vips
class slb-vip
loadbalance vip inservice
loadbalance policy slb
loadbalance vip icmp-reply
interface vlan 11
bridge-group 1
access-group input bpdu-fixup
access-group input ALL
access-group output ALL
no shutdown
interface vlan 13
bridge-group 1
access-group input bpdu-fixup
access-group input ALL
access-group output ALL
service-policy input remote-mgmt
service-policy input client-vips
no shutdown
interface bvi 1
ip address 172.16.11.9 255.255.255.0
no shutdown
ip route 0.0.0.0 0.0.0.0 172.16.11.254
Could you pls. suggest where I am doing wrong?
Thanks,
Pawan" I tried trunk port also but it got disabled" <----- if your L2 config is not correct, nothing will work.
What is the setup on the switch ? Trunk or access vlan ?
What is the status of the interface ? up ? down ?
Do you see something in your arp table ?
Gilles. -
Hi All ,
I am facing problem with my ACE 4710 in active-standby environment . When I check Show ft group detail on my Active ACE , it shows peer state as
FSM_FT_STATE_STANDBY_COLD for Admin context . Below is the output :
Primary_ACE/Admin#sh ft group detail
FT Group : 1
No. of Contexts : 1
Context Name : Admin
Context Id : 0
Configured Status : in-service
Maintenance mode : MAINT_MODE_OFF
My State : FSM_FT_STATE_ACTIVE
My Config Priority : 120
My Net Priority : 120
My Preempt : Enabled
Peer State : FSM_FT_STATE_STANDBY_COLD
Peer Config Priority : 100
Peer Net Priority : 100
Peer Preempt : Enabled
Peer Id : 1
Last State Change time : Tue Jan 1 05:32:55 2002
Running cfg sync enabled : Enabled
Running cfg sync status : Peer in Cold State. Error on Standby device when
applying configuration file replicated from active
Startup cfg sync enabled : Enabled
Startup cfg sync status : Peer in Cold State. Startup configuration sync ha
[7m--More--[m
s completed
Bulk sync done for ARP: 0
Bulk sync done for LB: 0
Bulk sync done for ICM: 0
FT Group : 2
No. of Contexts : 1
Context Name : APP_Context
Context Id : 1
Configured Status : in-service
Maintenance mode : MAINT_MODE_OFF
My State : FSM_FT_STATE_ACTIVE
My Config Priority : 120
My Net Priority : 120
My Preempt : Enabled
Peer State : FSM_FT_STATE_STANDBY_HOT
Peer Config Priority : 100
Peer Net Priority : 100
Peer Preempt : Enabled
Peer Id : 1
Last State Change time : Tue Jan 1 05:32:56 2002
Running cfg sync enabled : Enabled
[7m--More--[m
Running cfg sync status : Running configuration sync has completed
Startup cfg sync enabled : Enabled
Startup cfg sync status : Startup configuration sync has completed
Bulk sync done for ARP: 0
Bulk sync done for LB: 0
Bulk sync done for ICM: 0
Also when I give show ft config-errors on my secondary ACE it gives the following result .
Secondary_ACE/Admin#sh ft config-error
Mon Jun 10 00:04:11 IST 2002
`no 3 match virtual-address 10.40.3.15 tcp eq https`
Error: LB action requires match vip command
`no 3 match virtual-address 10.40.3.15 tcp eq 8082`
Error: LB action requires match vip command
`no 3 match virtual-address 10.40.3.21 tcp eq www`
Error: LB action requires match vip command
`no 3 match virtual-address 10.40.3.21 tcp eq https`
Error: LB action requires match vip command
`2 match virtual-address 10.40.3.21 tcp eq https`
Error: This configuration already exists
`2 match virtual-address 10.40.3.21 tcp eq www`
Error: This configuration already exists
`2 match virtual-address 10.40.3.15 tcp eq 8082`
Error: This configuration already exists
`2 match virtual-address 10.40.3.15 tcp eq https`
Error: This configuration already exists
Error(s) while applying config.
I am attaching the running configuration of both the ACE's . Kindly help me in resolving the issue .
Also I noticed one thing . There is configuration difference in Primary and Secondary ACE . I guess this is causing the issue .
Need help to fix this asap .
Following configuration is missing on the secondary ACE .
======================================================================
class-map match-all WEB_FARM_VIP-80
3 match virtual-address 10.40.3.15 tcp eq www
policy-map type loadbalance first-match WEB_FARM_VIP-80-l7slb
class class-default
serverfarm HTTP-2-HTTPS
class WEB_FARM_VIP-80
loadbalance vip inservice
loadbalance policy WEB_FARM_VIP-80-l7slb
Thanks ,
TusharDear all,
Pls help me out in this regard, I dont have much idea about ACE.
Regards,
Sashi -
ACE 4710 HTTPS load balance configuration
Have two ACE 4710 in HA setup. We would like to setup HTTPS loadbalance(actually just a primary and standby configuration in the serverfarm). Initially this would be for Exchange OWA connections but may expand to more HTTPS connections later.
I know there are several ways to do SSL with the ACE( client, server, end-to-end). I am just wanting to know the easiest way to deploy this? Is a certificate always needed on the ACE for each connection? In HA mode would a certificate be needed for both or does it replicate in some way to the other ACE?
Any configuration examples would be helpful.
Thanks.IF you terminate SSL on the ACE you need certificates and key on ace in the context in which you are doing the termination. The certs and keys need to be installed on the active and standby (manually unless using anm to manage).
when speaking of SSL
SSL termination refers to ace terminating SSL and sending to server as clear text
end to end - ACE terminates SSL (to look into payload to make a loadbalance decision or sticky decision) and then re-encrypts to the server, so to the client ACE is an ssl server and to the server the ace is an ssl client.
You can find some config examples at
http://docwiki.cisco.com/wiki/Category:Data_Center_Application_Services_Configuration_Examples -
ACE 4710 - can I dynamically sticky all traffic to 1 server based on URL?
Hello all, I'm new to the ACE 4710 and need to know some details about stickyness.
As background, we are a small company with a SaaS product and a pair of webservers.
I have set up the loadbalancing default L7 Load-balancing rule to sticky based on a Cookie based Stickey Group.
That seems to be working and session traffic is sticking to a server during the user's session.
Based on a request from our outsourced developer they would like the Loadbalancer to not only sticky the users sessions, but also sticky a url to a server.
I would like this to happen dynamically as each of our clients will have their own url based on our standard domain like clientname.fixeddomain.com and I don't want to have to come back to the loadbalancer every time we add a client.
As I said, I'm new to these devices but understand the concepts, and am in the position of having to make it work little to no tranining on this hardware and no budget at this point to pay someone else for configuration and setup.
I just need to know at this point if I can stick all requests for a specific URL to a server to avoid caching issue while those sessions are active and have new connections to other client urls balanced among the webservers.
Hopefully this request makes sense.
Thanks,
Mark Steeves.Daniel,
Thanks for the reply, but I cannot reach the URL you included. It gives me a 403.
Therfore without reading the article, I wanted to ask if the proper setup would be:
1. Default L7 load-balancing action: Primary action: Sticky: Stickey Group using
Type = HTTP Header: Header name = Host
2. Server Farm: Predictor: Least Connections or Round Robin to distribute the load between the 2 web servers.
Using this setting in testing, it looks like all the traffic keeps going to 1 server only. Granted there is not much traffic t the servers, but I have 2 different url being tested. url1.ourdomain.com & url2.ourdomain.com
If you have another link for the above document, please let me know.
Thanks,
Mark Steeves. -
Configuring ACE 4710 for Load Balancing Speech servers
Hello, I'm configuring ACE 4710's for the first time and I want to load balance my Nuance speech servers on port 554. Here's my configuration on ACE01:
hostname ace471001
interface gigabitEthernet 1/1
switchport access vlan 1000
no shutdown
interface gigabitEthernet 1/2
shutdown
interface gigabitEthernet 1/3
shutdown
interface gigabitEthernet 1/4
shutdown
access-list ALL line 8 extended permit ip any any
rserver host nss01
class-map type management match-any remote_access
2 match protocol xml-https any
3 match protocol icmp any
4 match protocol telnet any
5 match protocol ssh any
6 match protocol http any
7 match protocol https any
8 match protocol snmp any
policy-map type management first-match remote_mgmt_allow_policy
class remote_access
permit
interface vlan 1000
ip address 10.20.17.21 255.255.248.0
access-group input ALL
service-policy input remote_mgmt_allow_policy
no shutdown
How would I configure my speech server to isten on 554?
Thanks in advanceHello Reginald
Currently you have only basic network configuration, there is no loadbalancing config
I'm not sure what exactly you're asking about , but basically you need to have
- real servers configured on ACE (
http://www.cisco.com/en/US/docs/app_ntwk_services/data_center_app_services/ace_appliances/vA3_1_0/configuration/slb/guide/rsfarms.html#wp999495)
- serverfarm configured on ACE (
http://www.cisco.com/en/US/docs/app_ntwk_services/data_center_app_services/ace_appliances/vA3_1_0/configuration/slb/guide/rsfarms.html#wp1014522)
- L7 policy map (
http://www.cisco.com/en/US/docs/app_ntwk_services/data_center_app_services/ace_appliances/vA3_1_0/configuration/slb/guide/classlb.html#wp1171109 ,
http://www.cisco.com/en/US/docs/app_ntwk_services/data_center_app_services/ace_appliances/vA3_1_0/configuration/slb/guide/classlb.html#wp1027248 )
- L4 policy map , class-map (
http://www.cisco.com/en/US/docs/app_ntwk_services/data_center_app_services/ace_appliances/vA3_1_0/configuration/slb/guide/classlb.html#wp1027819)
And then apply it on necessary interface.
This is a general configuration, in your specific case you may need to configure some additinal features (e.g. I think you will need to have stickiness enabled
http://www.cisco.com/en/US/docs/app_ntwk_services/data_center_app_services/ace_appliances/vA3_1_0/configuration/slb/guide/sticky.html but it depends on your application)
links are for old config guids , but basic is pretty much the same for all versions.
Please check them and try to narrow down your question a bit. -
SIP load balancing issue with ACE 4710
SIP Load balancing Issue with ACE 4710
I have a Cisco ace 4710 with vesion Version A4(2.2). i configued simple SIP load balancing first without stickiness. without stikeiness we are having a problem because bye packet at the was not going to the same server all the time that left our port in used even though user hang up the phone. its happen randmly. i have a total 20 licenced ports and its fill out very quickly. so i dicided to use the stickiness with call-ID but still same issue. below is the config
rserver host CIN-VOX-31
ip address 172.20.130.31
inservice
rserver host CIN-VOX-32
ip address 172.20.130.32
inservice
serverfarm host CIN-VOX
probe SIP-5060
rserver CIN-VOX-31
inservice
rserver CIN-VOX-32
inservice
sticky sip-header Call-ID VOX_SIP_GROUP
timeout 1
timeout activeconns
replicate sticky
serverfarm CIN-VOX
class-map match-all CIN_VOX_L4_CLASS
2 match virtual-address 172.22.12.30 any
class-map match-all CIN_VOX_SIP_L4_CLASS
2 match virtual-address 172.22.12.30 udp eq sip
policy-map type loadbalance sip first-match CIN_VOX_LB_SIP_POLICY
class class-default
sticky-serverfarm VOX_SIP_GROUP
policy-map multi-match GLOBAL_DMZ_POLICY
class CIN_VOX_SIP_L4_CLASS
loadbalance vip inservice
loadbalance policy CIN_VOX_LB_SIP_POLICY
loadbalance vip icmp-reply
class CIN_VOX_L4_CLASS
loadbalance vip inservice
loadbalance policy CIN_VOX_LB_SIP_POLICY
loadbalance vip icmp-reply
interface vlan 20
description VIP_DMZ_VLAN
ip address 172.22.12.4 255.255.255.192
alias 172.22.12.3 255.255.255.192
peer ip address 172.22.12.5 255.255.255.192
access-group input PERMIT-ANY-LB
service-policy input GLOBAL_DMZ_POLICY
could you please help me on this...
thanks
Rakesh PatelI mean there should be one more statement-
class-map type sip loadbalance match-any CIN_VOX_LB_SIP_POLICY
match sip header Call_ID header-value sip:
and that will be called under-
policy-map multi-match GLOBAL_DMZ_POLICY
class CIN_VOX_SIP_L4_CLASS
loadbalance vip inservice
loadbalance policy CIN_VOX_LB_SIP_POLICY
loadbalance vip icmp-reply
is that missing in your config ? -
Hi,
Pls can you help me find out where is my error in the below:
I have an ACE 4710. Also I have 2 Bluecoat Proxy SG working in proxy mode. I want the ACE to be the Load Balancer for these 2 Proxy SG. I configure the ACE as below and put the vip-address in the Internet Explorer LAN Settings but it did not work. Also I configure Policy-based Routing on the Core Switch (for any http or https traffic going through core apply set ip next-hop vip-address).
Core SW SVI:
interface Vlan56
description BC Proxy
ip address 10.0.1.33 255.255.255.224
interface Vlan57
description ACE-LB-Alias
ip address 10.0.1.65 255.255.255.224
ACE 4710:
hostname VSS-ACE-BC-01
interface gigabitEthernet 1/1
description Management
speed 1000M
duplex FULL
switchport access vlan 101
no shutdown
interface gigabitEthernet 1/2
description User Side
speed 1000M
duplex FULL
switchport access vlan 56
no shutdown
interface gigabitEthernet 1/3
description BC Proxy Side
speed 1000M
duplex FULL
switchport access vlan 57
no shutdown
interface gigabitEthernet 1/4
description Failover
speed 1000M
duplex FULL
ft-port vlan 900
no shutdown
context Admin
member sticky
access-list external line 10 extended permit ip any any
access-list external line 20 extended permit icmp any any
access-list external line 30 extended permit tcp any any
access-list external line 40 extended permit udp any any
access-list internal line 10 extended permit ip any any
access-list internal line 20 extended permit icmp any any
access-list internal line 30 extended permit tcp any any
access-list internal line 40 extended permit udp any any
probe tcp web443
port 443
interval 30
faildetect 1
passdetect interval 30
passdetect count 1
open 1
probe tcp web8080
port 8080
interval 30
faildetect 1
passdetect interval 30
passdetect count 1
open 1
rserver host BC01
ip address 10.0.1.41
inservice
rserver host BC02
ip address 10.0.1.42
inservice
serverfarm host web443
probe web443
rserver BC01
inservice
rserver BC02
inservice
serverfarm host web8080
probe web8080
rserver BC01
inservice
rserver BC02
inservice
sticky ip-netmask 255.255.255.255 address source group1
replicate sticky
serverfarm web8080
sticky ip-netmask 255.255.255.255 address source group2
replicate sticky
serverfarm web443
class-map type management match-any REMOTE_ACCESS
2 match protocol telnet any
3 match protocol ssh any
4 match protocol icmp any
5 match protocol http any
6 match protocol snmp any
class-map match-all external-web
2 match virtual-address 10.0.1.70 any
class-map match-all external-web443
2 match virtual-address 10.0.1.70 any
class-map match-any nat-class
2 match access-list external
policy-map type management first-match REMOTE_MGMT
class REMOTE_ACCESS
permit
policy-map type loadbalance http first-match slb
class class-default
sticky-serverfarm group1
policy-map type loadbalance http first-match slb443
class class-default
sticky-serverfarm group2
policy-map multi-match external-access
class nat-class
nat dynamic 1 vlan 57
class external-web
loadbalance vip inservice
loadbalance policy slb
class external-web443
loadbalance vip inservice
loadbalance policy slb443
timeout xlate 120
interface vlan 56
description Server-Side
ip address 10.0.1.43 255.255.255.224
ip verify reverse-path
alias 10.0.1.40 255.255.255.224
peer ip address 10.0.1.44 255.255.255.224
mac-address autogenerate
access-group input internal
service-policy input REMOTE_MGMT
no shutdown
interface vlan 57
description VIP-Interface
ip address 10.0.1.67 255.255.255.224
alias 10.0.1.66 255.255.255.224
peer ip address 10.0.1.68 255.255.255.224
mac-address autogenerate
access-group input external
service-policy input external-access
service-policy input REMOTE_MGMT
no shutdown
interface vlan 101
description Management
ip address 10.220.1.131 255.255.255.0
alias 10.220.1.133 255.255.255.0
peer ip address 10.220.1.132 255.255.255.0
mac-address autogenerate
service-policy input REMOTE_MGMT
no shutdown
ft interface vlan 900
ip address 172.20.100.1 255.255.255.252
peer ip address 172.20.100.2 255.255.255.252
no shutdown
ft peer 1
heartbeat interval 300
heartbeat count 20
ft-interface vlan 900
ft group 1
peer 1
priority 200
peer priority 150
associate-context Admin
inservice
ip route 0.0.0.0 0.0.0.0 10.0.1.65I see that you used:
nat dynamic 1 vlan 57
Where is the nat pool on Vlan 57 ?
May be you can try to assign that and that should help.
Something like below:
Interface vlan 57
nat-pool 1 10.0.1.93 10.0.1.93 netmask 255.255.255.224 pat
regards,
Ajay Kumar -
ACE 4710 - Gracefully Shutting Down a Server
Hi,
Recently I had to stop an RServer to allow for software upgrades. I entered a no inservice command in the rserver config and all the connections on the serverfarm disappeared. I thought the no inservice should allow existing connections to finish. Is there another way of taking a server out of service?
We are running on an ACE 4710 version A3(2.5). We offload SSL on the ACE and use sticky connections using cookie insert
Thanks for your helpHi,
To gracefully shutdown use the "no inservice" on the rserver within the serverfarm rather than on the rserver definition.
HTH
Cathy
Maybe you are looking for
-
Error while creating a new paymentgroup
Hi, I implemented a new payment method by following the guide in section Extending the Payment Process to Support a New Payment Method, i followed all the steps to create it and i created a new form handler extending GenericFormHandler to receive all
-
Unable to open the Projects from Project center with the Alias name PWA 2010
Hi, I am unable to open the Projects from Project center with the Alias name with the server name i am able to open the projects, version is project server 2010, My system is ABC.DC.IN alias name i have given is DEF.AD.COM With the system name i
-
Manage multiple Adobe Type Kit sets
Is there a way to manage or see my teams Adobe Type Kit sets from the plan administrator's console? If not do you have a method or recommendation for monitoring or consolidating the Adobe Type Kit sets across multiple users?
-
When I upgrade to Snow Leopard, do I need to reinstall all of my programs?
When I upgrade to Snow Leopard from OS x 10.4.11, do I need to reinstall all of my programs, such as Microsoft Office Suite?
-
How To Uninstall Cateye?
I installed cateye today and it made my photo booth run really slow. I've tried to uninstall it by going to System > Library > Composition. In "Composition" all I found was the .qtz files of the original photo booth effect - I couldn't find any catey